Superbroadband 1310 nm emission from bismuth and tantalum codoped germanium oxide glasses

Near-infrared broadband emission from bismuth-tantalum-codoped germanium oxide glasses was observed at room temperature when the glasses were pumped by an 808 nm laser diode. The emission band covered the 0, E, S, C, and L bands (1260-1625 nm), with a maximum peak at similar to 1310 nm, a FWHM broader than 400 nm, and a lifetime longer than 200 lis. The observed broadband luminescence was attributed to bismuth clusters in the glasses. Bismuth-tantalum-codoped germanium oxide glass might be promising as amplification media for broadly tunable lasers and wideband amplifiers in optical communications. (c) 2005 Optical Society of America.

Bismuth-doped fiber integrated ring laser mode-locked with a nanotube-based saturable absorber

We demonstrate passive mode-locking of a bismuth-doped fiber laser using a single-wall nanotube-based saturable absorber. Stable operation in the all-normal dispersion and average soliton regime is obtained, with an all-fiber integrated format. © 2010 Optical Society of America.

Anodic Stripping Voltammetry at Bismuth-Coated and Uncoated Carbon Microdisk Electrodes:Application to Trace Metals Analysis in Flood Samples

This article reports on the performance of a bismuth-coated carbon microdisk electrode (BiFμE) for the determination of trace heavy metals by anodic stripping voltammetry (ASV). The BiFμE was prepared by electrodeposition of a metallic bismuth film onto the microdisk, by applying an in-situ electroplating procedure. To test the performance of the BiFμE, ASV measurements were performed on synthetic solutions containing Cd2+, Pb2+, and Cu2+ as target ions. The results indicated that cadmium and lead gave well-defined ASV peaks with no interference, and their quantitative determination could be carried out straightforwardly. In particular, linear calibration curves over the range 5.0 x 10-8-1.0 x 10-6M for both ions, and detection limits of 7.8 and 2.9 nM, for cadmium and lead, respectively, after applying a 60 sec preconcentration step, were obtained. The reproducibility was also satisfactory, the relative standard deviation (RSD) being within 2.5% for both ions. Copper, instead, gave an ASV response that. in most experimental conditions, overlapped with that of bismuth. This circumstance made the determination of copper at the BiFμE difficult. Since the latter element could be detected reliably at the uncoated carbon microdisk electrode (CμE), both BiFμE and CμE were employed, respectively, for the determination of lead and copper ions in drinking water, wine, and tomato sauce.

Stripping voltammetric determination of Pb(II) and Cd(II) based on the multiwalled carbon nanotubes-Nafion-bismuth modified glassy carbon electrodes

In this work, a new method for the simultaneous determination of Pb(II) and Cd(II) on the multiwalled carbon nanotubes (MWNT)-Nafion-bismuth modified glassy carbon electrode (GCE) using square-wave anodic stripping voltammetry has been studied. Scanning electron microscopy was used to investigate the characteristics of the MWNT-Nafion-bismuth modified GCE.

Properties of poly(sodium 4-styrenesulfonate)-ionic liquid composite film and its application in the determination of trace metals combined with bismuth film electrode

A new kind of bismuth film modified electrode to sensitively detect trace metal ions based on incorporating highly conductive ionic liquids 1-butyl-3-methyl-imidazolium hexafluorophosphate (BMIMPF6) in solid matrices at glassy carbon (GC) was investigated. Poly(sodium 4-styrenesulfonate) (PSS), silica, and Nafion were selected as the solid matrices. The electrochemical properties of the mixed films modified GC were evaluated. The electron transfer rate of Fe(CN)(6)(4-)/Fe(CN)(6)(3-) can be effectively improved at the PSS-BMIMPF6 modified GC.

Sensitive determination of Cd and Pb by differential pulse stripping voltammetry with in situ bismuth-modified zeolite doped carbon paste electrodes

Here we investigated the analytical performances of the bismuth-modified zeolite doped carbon paste electrode (BiF-ZDCPE) for trace Cd and Pb analysis. The characteristics of bismuth-modified electrodes were improved greatly via addition of synthetic zeolite into carbon paste. To obtain high reproducibility and sensitivity, optimum experimental conditions for bismuth deposition Were Studied.

Narion/Poly(sodium 4-styrenesulfonate) mixed coating modified bismuth film electrode for the determination of trace metals by anodic stripping voltammetry

To improve the reproducibility, stability, and sensitivity of bismuth film electrode (BiFE), we studied the performances of a mixed coating of two cation-exchange polymers, Nafion (NA) and poly(sodium 4-styrenesulfonate) (PSS), modified glassy carbon BiFE (GC/NA-PSS/BiFE). The characteristics of GC/NA-PSS/BiFE were investigated by scanning electron microscopy and cyclic voltammetry. Various parameters were studied in terms of their effect on the anodic stripping voltarnmetry (ASV) signals. Under optimized conditions, the limits of detection were 71 ng L-1 for Cd(II) and 93 ng L-1 for Pb(II) with a 10 min preconcentration. The results exhibited that GC/NA-PSS/BiFE can be a reproducible and robust toot for monitor of trace metals by ASV rapidly and environmentally friendly, even in the presence of surface-active compounds.

Cathodic electrochemiluminescence in aqueous solutions at bismuth electrodes

The high hydrogen evolution overpotential of a bismuth electrode makes it a powerful electrode for cathodic electro-chemiluminescence studies in aqueous solutions.

Luminescence of unusual bismuth in barium berates BaB8O13 : Bi)

The luminescence of unusual divalent bismuth (Bi2+) in BaB8O13 is reported. The emission band with maximum peak at 592 nm corresponds to the P-2(3/2)-->P-2(1/2) transition of Bi2+ in the matrix and the excitation spectrum with two bands peaked at 470 and 580 nm respectively corresponds to two split crystal-field levels of P-2(3/2) state. The small Stokes shift (similar to 350 cm(-1)) reflects the rigid structure of the host for the Bi2+ ions.

Catalytic mechanisms of triphenyl bismuth, dibutyltin dilaurate, and their combination in polyurethane-forming reaction

The catalytic mechanisms of triphenyl bismuth (TPB), dibutyltin dilaurate (DBTDL) and their combination have been studied in a model polyurethane reaction system consisting of copolyether (tetrahydrofuran-ethyleneoxide) and N-100; NMR spectroscopy was used to detect the associations between reactants and catalysts. A relatively stable complex was shown to be formed between hydroxyl and isocyanate; the catalysts showed different effects on the isocyanate-hydroxyl complex, therefore resulting in different curing characteristics. The formation of hydrogen bonding between the complexed hydroxyl and other hydroxyl or the resulting urethane provided an ''auto-catalysis'' to urethane formation. DBTDL destroyed the isocyanate-hydroxyl complex before catalyzing the reaction through the formation of a ternary complex, whereas TPB was able to activate the isocyanate-hydroxyl complex directly to form urethane. The reaction catalyzed by the combination of TPB and DBTDL gained advantages from the multiple catalytic entities, i.e., TPB, DBTDL, and a TPB-DBTDL complex. (C) 1997 John Wiley & Sons, Inc.

Influence of crystal structure on the luminescence properties of bismuth(III), europium(III) and dysprosium(III) in Y2SiO5

The luminescence properties of Bi3+, EU(3+), Dy3+ and energy transfer from Bi3+ to Dy3+ and EU(3+) have been studied in two modifications of Y2SiO5 (low-temperature X(1) type and high-temperature X(2) type) and discussed in relation to their crystal structures. The Bi3+ ion luminesces in the blue region of the spectrum in X(1)-Y2SiO5 but in the UV region in X(2)-Y2SiO5. Two obviously different luminescent centres have been observed for Bi3+ and Eu3+ ill X(1)-Y2SiO5, but only one has been seen in X(2)-Y2SiO5. The Stokes shift (9200 cm(-1)) for Bi3+ in X(1)-Y2SiO5 is much larger than that (5000 cm(-1)) in X(2)-Y2SiO5. This suggests that the host lattice is more rigid in X(2)-Y2SiO5 than in X(1)-Y2SiO5. As a result, the Bi3+, EU(3+) and Dy3+ ions show higher emission intensity in the former than in the latter type. X(1)-Y2SiO5 is more suitable for Bi3+ --> EU(3+) energy transfer and X(2)-Y2SiO5 is more suitable for Bi3+ --> Dy3+ energy transfer.

PREPARATION AND ELECTRICAL-PROPERTIES OF BISMUTH STRONTIUM DIMANGANESE HEXOXIDE [BISRMN2O6]

BiSrMn2O6 is prepared by solid state reaction at 850 degrees C. It is tetragonal with a= 0.7821nm c= 0.3790 nm. It is a black n-type semiconductor below 820K. Its resistivity is 3 Omega-CM at room temperature. A semiconductor -metal transition is observed around 820K, Bi1+xSr1-xMn2O6-y is a solid solution for -0.2 less than or equal to x less than or equal to 0.2. Its unit cell dimensions increase but resistivity decreases when the Bi contents increase.