Water distribuition characteristics and soil loss of LEPA Quad-Spray emitter nozzles

The objective of this study was to characterize water application rate, water application pattern width, flow rate, water distribution uniformity and soil loss caused by nozzles of the Low Energy Precision Aplication (LEPA) type Quad-Spray emitter. The study was carried out at the Hydraulic and Irrigation Laboratory of the Department of Engineering at the Federal University of Lavras, in Lavras, state of Minas Gerais - MG, Brazil. Twenty-two (22) LEPA Quad-Spray emitter nozzles were evaluated, with nozzle diameter ranging from 1.59 to 9.92 mm. The experimental design used was entirely randomized, with three replications.Increasing values of nozzle flow rate ranging from 77.44 up to 3,044 L h-1, were obtained with increasing nozzle diameter sizes. Application pattern width ranged from 0.56 up to 3.24m, according to nozzles diameter size. Low values of CDU (maximum of 35.73%) were observed when using the Quad-Spray nozzles. Observed average water application rates covered the range between 68.05 mm h-1 (the lowest value that was obtained with the 2.38mm nozzle) and 258.15 mm h-1 (the highest value that was observed with the 9.92 mm). Average water application rates increased in a simple non-linear function with the increase of nozzle size diameter. However, the weighted average increase in the amount of soil loss by erosion was not related to the increase of weighted average water application values.

Beta and debt premium for a Finnish distribution company

Suomessa sähkönjakelu on säännelty monopoli. Energiamarkkinavirasto tuottaa ohjeistuksen sekä mallin yritysten ansaintamahdollisuuksille. Karkeasti sanottuna tulomalli on sijoitetun pääoman ja pääoman painotetun kustannuksen tulo. Pääoman painotettu kustannus koostuu useista parametreista kuten beta ja vieraan pääoman riskipreemio. Näiden parametrien taso ja määrittämisajankohta perustuvat subjektiivisiin näkemyksiin, kun objektiivista parametrien määrittämismenetelmää tulisi käyttää. Nykyiset beta ja vieraan pääoman riskipreemio perustuvat energiamarkkinaviraston ja asiantuntijoiden lausuntoihin. Aihealuetta on tutkittu erittäin vähän, mikä johtunee pääasiassa siitä, ettei ole olemassa listautuneita puhtaita jakeluverkkoyhtiöitä. Betan nykytaso on 0.529 ja vieraan pääoman riskipreemio on 1.0 %. Tässä pro gradu –työssä määritetään markkinaperusteisesti betan ja vieraan pääoman riskipreemion nykytaso. Tässä työssä esiteltävä määrittämismalli perustuu puhtaasti markkinadataan eikä sen soveltamisessa käytetä subjektiivisia mielipiteitä. Markkinaehtoisia tietoja käyttäen betan pitäisi olla tasolla 0.525 ja vieraan pääoman riskipreemion tasolla 1.34 %. Nämä luvut, mikäli ne otettaisiin käyttöön, vaikuttaisivat suoraan ja positiivisesti jakeluverkkoyhtiöiden sallittuun tuottoon Suomessa.

Energy Efficiency of a Diesel-Electric MobileWorking Machine

The power demand of many mobile working machines such as mine loaders, straddle carriers and harvesters varies significantly during operation, and typically, the average power demand of a working machine is considerably lower than the demand for maximum power. Consequently, for most of the time, the diesel engine of a working machine operates at a poor efficiency far from its optimum efficiency range. However, the energy efficiency of dieseldriven working machines can be improved by electric hybridization. This way, the diesel engine can be dimensioned to operate within its optimum efficiency range, and the electric drive with its energy storages responds to changes in machine loading. A hybrid working machine can be implemented in many ways either as a parallel hybrid, a series hybrid or a combination of these two. The energy efficiency of hybrid working machines can be further enhanced by energy recovery and reuse. This doctoral thesis introduces the component models required in the simulation model of a working machine. Component efficiency maps are applied to the modelling; the efficiency maps for electrical machines are determined analytically in the whole torque–rotational speed plane based on the electricalmachine parameters. Furthermore, the thesis provides simulation models for parallel, series and parallel-series hybrid working machines. With these simulation models, the energy consumption of the working machine can be analysed. In addition, the hybridization process is introduced and described. The thesis provides a case example of the hybridization and dimensioning process of a working machine, starting from the work cycle of the machine. The selection and dimensioning of the hybrid system have a significant impact on the energy consumption of a hybrid working machine. The thesis compares the energy consumption of a working machine implemented by three different hybrid systems (parallel, series and parallel-series) and with different component dimensions. The payback time of a hybrid working machine and the energy storage lifetime are also estimated in the study.

Real-time monitoring of laser scribing process utilizing high-speed camera

Currently, laser scribing is growing material processing method in the industry. Benefits of laser scribing technology are studied for example for improving an efficiency of solar cells. Due high-quality requirement of the fast scribing process, it is important to monitor the process in real time for detecting possible defects during the process. However, there is a lack of studies of laser scribing real time monitoring. Commonly used monitoring methods developed for other laser processes such a laser welding, are sufficient slow and existed applications cannot be implemented in fast laser scribing monitoring. The aim of this thesis is to find a method for laser scribing monitoring with a high-speed camera and evaluate reliability and performance of the developed monitoring system with experiments. The laser used in experiments is an IPG ytterbium pulsed fiber laser with 20 W maximum average power and Scan head optics used in the laser is Scanlab’s Hurryscan 14 II with an f100 tele-centric lens. The camera was connected to laser scanner using camera adapter to follow the laser process. A powerful fully programmable industrial computer was chosen for executing image processing and analysis. Algorithms for defect analysis, which are based on particle analysis, were developed using LabVIEW system design software. The performance of the algorithms was analyzed by analyzing a non-moving image from the scribing line with resolution 960x20 pixel. As a result, the maximum analysis speed was 560 frames per second. Reliability of the algorithm was evaluated by imaging scribing path with a variable number of defects 2000 mm/s when the laser was turned off and image analysis speed was 430 frames per second. The experiment was successful and as a result, the algorithms detected all defects from the scribing path. The final monitoring experiment was performed during a laser process. However, it was challenging to get active laser illumination work with the laser scanner due physical dimensions of the laser lens and the scanner. For reliable error detection, the illumination system is needed to be replaced.

Diatoms as indicators of lake trophic status

Relationships between surface sediment diatom assemblages and lake trophic status were studied in 50 Canadian Precambrian Shield lakes in the Muskoka-Haliburton and southern Ontario regions. The purpose of this study was to develop mathematical regression models to infer lake trophic status from diatom assemblage data. To achieve this goal, however, additional investigations dealing with the evaluation of lake trophic status and the autecological features of key diatom species were carried out. Because a unifying index and classification for lake trophic status was not available, a new multiple index was developed in this study, by the computation of the physical, chemical and biological data from 85 south Ontario lakes. By using the new trophic parameter, the lake trophic level (TL) was determined: TL = 1.37 In[1 +(TP x Chl-a / SD)], where, TP=total phosphorus, Chl-a=chlorophyll-a and SD=Secchi depth. The boundaries between 7 lake trophic categories (Ultra-oligotrophic lakes: 0-0.24; Oligotrophic lakes: 0.241-1.8; Oligomesotrophic lakes: 1.813.0; Mesotrophic lakes: 3.01-4.20; Mesoeutrophic lakes: 4.21-5.4; Eutrophic lakes: 5.41-10 and Hyper-eutrophic lakes: above 10) were established. The new trophic parameter was more convenient for management of water quality, communication to the public and comparison with other lake trophic status indices than many of the previously published indices because the TL index attempts to Increase understanding of the characteristics of lakes and their comprehensive trophic states. It is more reasonable and clear for a unifying determination of true trophic states of lakes. Diatom specIes autecology analysis was central to this thesis. However, the autecological relationship of diatom species and lake trophic status had not previously been well documented. Based on the investigation of the diatom composition and variety of species abundance in 30 study lakes, the distribution optima of diatom species were determined. These determinations were based on a quantitative method called "weighted average" (Charles 1985). On this basis, the diatom species were classified into five trophic categories (oligotrophic, oligomesotrophic, mesotrophic, mesoeutrophic and eutrophic species groups). The resulting diatom trophic status autecological features were used in the regressIon analysis between diatom assemblages and lake trophic status. When the TL trophic level values of the 30 lakes were regressed against their fi ve corresponding diatom trophic groups, the two mathematical equations for expressing the assumed linear relationship between the diatom assemblages composition were determined by (1) uSIng a single regression technique: Trophic level of lake (TL) = 2.643 - 7.575 log (Index D) (r = 0.88 r2 = 0.77 P = 0.0001; n = 30) Where, Index D = (0% + OM% + M%)/(E% + ME% + M%); 4 (2) uSIng a' multiple regressIon technique: TL=4.285-0.076 0%- 0.055 OM% - 0.026 M% + 0.033 ME% + 0.065 E% (r=0.89, r2=0.792, P=O.OOOl, n=30) There was a significant correlation between measured and diatom inferred trophic levels both by single and multiple regressIon methods (P < 0.0001, n=20), when both models were applied to another 20 test lakes. Their correlation coefficients (r2 ) were also statistically significant (r2 >0.68, n=20). As such, the two transfer function models between diatoms and lake trophic status were validated. The two models obtained as noted above were developed using one group of lakes and then tested using an entirely different group of lakes. This study indicated that diatom assemblages are sensitive to lake trophic status. As indicators of lake trophic status, diatoms are especially useful in situations where no local trophic information is available and in studies of the paleotrophic history of lakes. Diatom autecological information was used to develop a theory assessing water quality and lake trophic status.

Large-Size AlGaN/GaN HEMT Large-Signal Electrothermal Characterization and Modeling for Wireless Digital Communications

The rapid growth in high data rate communication systems has introduced new high spectral efficient modulation techniques and standards such as LTE-A (long term evolution-advanced) for 4G (4th generation) systems. These techniques have provided a broader bandwidth but introduced high peak-to-average power ratio (PAR) problem at the high power amplifier (HPA) level of the communication system base transceiver station (BTS). To avoid spectral spreading due to high PAR, stringent requirement on linearity is needed which brings the HPA to operate at large back-off power at the expense of power efficiency. Consequently, high power devices are fundamental in HPAs for high linearity and efficiency. Recent development in wide bandgap power devices, in particular AlGaN/GaN HEMT, has offered higher power level with superior linearity-efficiency trade-off in microwaves communication. For cost-effective HPA design to production cycle, rigorous computer aided design (CAD) AlGaN/GaN HEMT models are essential to reflect real response with increasing power level and channel temperature. Therefore, large-size AlGaN/GaN HEMT large-signal electrothermal modeling procedure is proposed. The HEMT structure analysis, characterization, data processing, model extraction and model implementation phases have been covered in this thesis including trapping and self-heating dispersion accounting for nonlinear drain current collapse. The small-signal model is extracted using the 22-element modeling procedure developed in our department. The intrinsic large-signal model is deeply investigated in conjunction with linearity prediction. The accuracy of the nonlinear drain current has been enhanced through several issues such as trapping and self-heating characterization. Also, the HEMT structure thermal profile has been investigated and corresponding thermal resistance has been extracted through thermal simulation and chuck-controlled temperature pulsed I(V) and static DC measurements. Higher-order equivalent thermal model is extracted and implemented in the HEMT large-signal model to accurately estimate instantaneous channel temperature. Moreover, trapping and self-heating transients has been characterized through transient measurements. The obtained time constants are represented by equivalent sub-circuits and integrated in the nonlinear drain current implementation to account for complex communication signals dynamic prediction. The obtained verification of this table-based large-size large-signal electrothermal model implementation has illustrated high accuracy in terms of output power, gain, efficiency and nonlinearity prediction with respect to standard large-signal test signals.

Valoración del costo de los recursos propios de las empresas. caso particular: empresas de servicios a la persona en Francia

El WACC o Coste Medio Ponderado de Capital es la tasa a la que se deben descontar los flujos para evaluar un proyecto o empresa. Para calcular esta tasa es necesario determinar el costo de la deuda y el costo de los recursos propios de la compañía; el costo de la deuda es la tasa actual del mercado que la empresa está pagando por su deuda, sin embargo el costo de los recursos propios podría ser difícil y más complejo de estimar ya que no existe un costo explícito. En este trabajo se presenta un panorama de las teorías propuestas a lo largo de la historia para calcular el costo de los recursos propios. Como caso particular, se estimará el costo de los recursos propios sin apalancamiento financiero de seis empresas francesas que no cotizan en bolsa y pertenecientes al sector de Servicios a la Persona (SAP). Para lograr lo anterior, se utilizará el Proceso de Análisis Jerárquico (AHP) y el Modelo de Valoración del Precio de los Activos Financieros (CAPM) con base en lo presentado por Martha Pachón (2013) en “Modelo alternativo para calcular el costo de los recursos propios”.

Caracterización de la exposición ocupacional a los gases, dióxido de azufre (so2), sulfuro de hidrógeno (h2s), y monóxido de carbono (co), y la percepción de salud de los trabajadores, en una empresa del sector hidrocarburo en Colombia

En el proceso de extracción de petróleo (crudo) deben realizarse tratamientos físicos y químicos en estaciones de recolección del hidrocarburo con el fin de garantizar su calidad antes de su entrega para el transporte y comercialización. Para la realización de esta actividad el personal operativo requerido (operadores) debe realizar diferentes actividades, tales como ronda operacional, verificación de sistemas de almacenamiento del crudo, agua residual del proceso e insumos químicos utilizados en su tratamiento y manipulación de facilidades en las estaciones de recolección, entre otras. Como resultados de las actividades rutinarias los operadores están expuestos a factores de riesgo químico asociados a gases y vapores orgánicos generados en los procesos de tratamiento del crudo. En el presente trabajo se realizaron mediciones de calidad de aire e higiene industrial en diferentes estaciones tratamiento de crudo, con el propósito de evaluar los niveles de exposición de los operadores a gases y vapores de hidrocarburos durante el proceso de tratamiento de crudo y dar respuesta a la siguiente pregunta: ¿existe relación entre la exposición ocupacional, las emisiones atmosféricas de gases (SO2, CO, H2S) y la percepción de afectación de la salud de los trabajadores que se encuentran expuestos durante la actividad laboral, en una empresa del sector de hidrocarburos? Se realizó un estudio de corte transversal, mediante la aplicación de cuestionarios sobre las condiciones de trabajo y de salud a 30 trabajadores que laboran en una estación de tratamiento de crudo de una compañía del sector de hidrocarburos. Los operadores objeto de estudio laboran en turnos rotativos, han estado vinculados con la compañía por más de dos años y tienen contrato directo, adicionalmente, se identificaron los factores de riesgos ambientales y ocupacionales para el grupo de trabajadores y se realizó una revisión de los informes de medición de higiene industrial y de calidad de aire de las estaciones donde labora el personal seleccionado con el fin de establecer si los resultados se relacionan. Los resultados obtenidos indican que el 100% de los trabajadores son de género masculino y se desempeñan en cargos de operadores, recorredores de pozos de crudo y supervisores. El 97% de los operadores tiene más de cuarenta años de edad y el 80% de los mismos ha laborado por más de 6 años en la compañía. Acerca de la percepción de los trabajadores sobre su estado de salud el 90% afirma que su salud es buena, el 97% respondió que no presenta problemas respiratorios, el 23% manifiesta que presenta trastornos dermatológicos y el 27% indican que presenta dolor de cabeza constante. De la revisión de los informes de calidad de aire disponibles se encontró que las mediciones de Dióxido de Azufre SO2, Monóxido de Carbono CO se encuentran dentro del rango definido como el de menor impacto para la salud humana. De los datos del informe se puede concluir que la calidad del aire es buena en el 100% de las áreas de influencia de las estaciones de tratamiento de crudo. Según los informes de higiene industrial el 34% de las instalaciones presenta concentraciones de Sulfuro de Hidrógeno (H2S) en el límite permisible para exposiciones crónicas en un promedio ponderado de tiempo (TLV-TWA) y el límite permisible para exposiciones agudas en un límite de exposición a corto plazo (TLV-STEL). Solo el 37% de los trabajadores objeto de este estudio percibe el riesgo por la exposición a factores de riesgo químicos y son claramente consientes que se encuentran expuestos a estos riesgos por la manipulación de productos químicos y exposición a sustancias químicas producto de sus actividades rutinarias, el 73% no percibe el riesgo de exposición por su actividad laboral. Se recomienda que la compañía fortalezca su esquema de vigilancia para generar alternativas que eleven los niveles de consciencia del riesgo del trabajador. Los factores de riesgo ambiental y ocupacional, de los gases y vapores generados se deben al proceso de tratamiento de crudo, están mutuamente relacionados dado que al generarse una emisión y/o escape no controlado como consecuencia se tiene una afectación directa al medio ambiente y a los trabajadores.

Modelos de presupuestación de capital en finanzas corporativas y utilidad de los mismos

La siguiente investigación describe una aproximación teórica al tema de los modelos de presupuestación de capital, el objetivo fundamental se basa en comprender su enfoque e importancia al momento de tomar decisiones de inversión por parte de los directores de una empresa, así como de prever los efectos de esta en un futuro. Al respecto, y sobre la base de que los modelos de presupuestación de capital son herramientas para analizar posibles erogaciones de capital por parte de una empresa, es necesario para efectos del presente proyecto de investigación, definir sus diferentes modelos desde lo teórico y metodológico, explicando los diferentes conceptos relacionados con el tema. Así mismo, se explican algunos de los indicadores financieros utilizados en las compañías para medir y estimar la “salud financiera” de la empresa, además de puntualizar su impacto en la perdurabilidad de las entidades, lo cual permite dar una visión más general sobre la importancia que trasciende de los indicadores financieros, generando un impacto positivo en la evolución o crecimiento de la organización. En complemento, la investigación aborda la presupuestación de capital de manera particular aplicado en la gestión empresarial, sean estas privadas o públicas (estatal y gubernamental). En este sentido, se abordan conceptos elaborados por diferentes académicos en los que se exponen algunas aproximaciones respecto al posible mejoramiento de la presupuestación para los sectores a los que pertenecen determinadas entidades. Finalmente, se presenta de manera explícita las conclusiones que surgieron a lo largo de la construcción del documento de investigación, con el fin de dar cumplimiento concreto al objetivo general del trabajo, el cual constituye una respuesta a la pregunta de investigación que se enunciará en el desarrollo del documento.

The return due to diversification of real estate to the US mixed-asset portfolio

Booth and Fama (1992) observe that the compound return and so the terminal wealth of a portfolio is greater than the weighted average of the compound returns of the individual investments, a difference referred to as the return due to diversification (RDD). Thus assets that offer high RDD should be particularly attractive investments. This paper test the proposition that US direct real estate is such an asset class using annual data over the period 1951-2001. The results show that adding real estate to an existing mixed-asset portfolio increases the compound return and so the terminal wealth of the fund. However, the results are dependent on the percentage allocation to real estate and the asset class replaced.

Cyclic prefixed OQAM-OFDM and its application to single-carrier FDMA

Single-carrier frequency division multiple access (SC-FDMA) has appeared to be a promising technique for high data rate uplink communications. Aimed at SC-FDMA applications, a cyclic prefixed version of the offset quadrature amplitude modulation based OFDM (OQAM-OFDM) is first proposed in this paper. We show that cyclic prefixed OQAMOFDM CP-OQAM-OFDM) can be realized within the framework of the standard OFDM system, and perfect recovery condition in the ideal channel is derived. We then apply CP-OQAMOFDM to SC-FDMA transmission in frequency selective fading channels. Signal model and joint widely linear minimum mean square error (WLMMSE) equalization using a prior information with low complexity are developed. Compared with the existing DFTS-OFDM based SC-FDMA, the proposed SC-FDMA can significantly reduce envelope fluctuation (EF) of the transmitted signal while maintaining the bandwidth efficiency. The inherent structure of CP-OQAM-OFDM enables low-complexity joint equalization in the frequency domain to combat both the multiple access interference and the intersymbol interference. The joint WLMMSE equalization using a prior information guarantees optimal MMSE performance and supports Turbo receiver for improved bit error rate (BER) performance. Simulation resultsconfirm the effectiveness of the proposed SC-FDMA in termsof EF (including peak-to-average power ratio, instantaneous-toaverage power ratio and cubic metric) and BER performances.

CP-OQAM-OFDM based SC-FDMA: adjustable user bandwidth and space-time coding

The discrete Fourier transmission spread OFDM DFTS-OFDM) based single-carrier frequency division multiple access (SC-FDMA) has been widely adopted due to its lower peak-to-average power ratio (PAPR) of transmit signals compared with OFDM. However, the offset modulation, which has lower PAPR than general modulation, cannot be directly applied into the existing SC-FDMA. When pulse-shaping filters are employed to further reduce the envelope fluctuation of transmit signals of SC-FDMA, the spectral efficiency degrades as well. In order to overcome such limitations of conventional SC-FDMA, this paper for the first time investigated cyclic prefixed OQAMOFDM (CP-OQAM-OFDM) based SC-FDMA transmission with adjustable user bandwidth and space-time coding. Firstly, we propose CP-OQAM-OFDM transmission with unequally-spaced subbands. We then apply it to SC-FDMA transmission and propose a SC-FDMA scheme with the following features: a) the transmit signal of each user is offset modulated single-carrier with frequency-domain pulse-shaping; b) the bandwidth of each user is adjustable; c) the spectral efficiency does not decrease with increasing roll-off factors. To combat both inter-symbolinterference and multiple access interference in frequencyselective fading channels, a joint linear minimum mean square error frequency domain equalization using a prior information with low complexity is developed. Subsequently, we construct space-time codes for the proposed SC-FDMA. Simulation results confirm the powerfulness of the proposed CP-OQAM-OFDM scheme (i.e., effective yet with low complexity).

TCL/TK for EDA tools

Tcl/Tk scripting language has become the de-facto standard for EDA tools. This paper explains how to start working with Tcl/Tk using simple examples. Two complete applications are presented to show in more detail the capabilities of the language. In one script average power consumption of a digital system is automated. A second script creates a virtual display driven by the simulation of a graphic card.

Low-level Laser Therapy Improves Skeletal Muscle Performance, Decreases Skeletal Muscle Damage and Modulates mRNA Expression of COX-1 and COX-2 in a Dose-dependent Manner

We tested if modulation in mRNA expression of cyclooxygenase isoforms (COX-1 and COX-2) can be related to protective effects of phototherapy in skeletal muscle. Thirty male Wistar rats were divided into five groups receiving either one of four laser doses (0.1, 0.3, 1.0 and 3.0 J) or a no-treatment control group. Laser irradiation (904 nm, 15 mW average power) was performed immediately before the first contraction for treated groups. Electrical stimulation was used to induce six tetanic tibial anterior muscle contractions. Immediately after sixth contraction, blood samples were collected to evaluate creatine kinase activity and muscles were dissected and frozen in liquid nitrogen to evaluate mRNA expression of COX-1 and COX-2. The 1.0 and 3.0 J groups showed significant enhancement (P < 0.01) in total work performed in six tetanic contractions compared with control group. All laser groups, except the 3.0 J group, presented significantly lower post-exercise CK activity than control group. Additionally, 1.0 J group showed increased COX-1 and decreased COX-2 mRNA expression compared with control group and 0.1, 0.3 and 3.0 J laser groups (P < 0.01). We conclude that pre-exercise infrared laser irradiation with dose of 1.0 J enhances skeletal muscle performance and decreases post-exercise skeletal muscle damage and inflammation.

Determination of dental decay rates with optical coherence tomography

We report the use of optical coherence tomography (OCT) to detect and quantify demineralization process induced by S. mutans biofilm in third molars human teeth. Artificial lesions were induced by a S. mutans microbiological culture and the samples (N = 50) were divided into groups according to the demineralization time: 3, 5, 7, 9, and 11days. The OCT system was implemented using a light source delivering an average power of 96 mu W in the sample arm, and spectral characteristics allowing 23 mu m of axial resolution. The images were produced with lateral scans step of 10 pan and analyzed individually. As a result of the evaluation of theses images, lesion depth was calculated as function of demineralization time. The depth of the lesion in the root dentine increased from 70 pm to 230,urn (corrected by the enamel refraction index, 1.62 @ 856 nm), depending of exposure time. The lesion depth in root dentine was correlated to demineralization time, showing that it follows a geometrical progression like a bacteria growth law. [GRAPHICS] Progression of lesion depth in root dentine as function of exposure time, showing that it follows a geometrical progression like a bacteria growth law(C) 2009 by Astro Ltd. Published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA