The impact of location and type on the performance of Low-Voltage network connected Battery Energy Storage Systems

This paper assesses the impact of the location and configuration of Battery Energy Storage Systems (BESS) on Low-Voltage (LV) feeders. BESS are now being deployed on LV networks by Distribution Network Operators (DNOs) as an alternative to conventional reinforcement (e.g. upgrading cables and transformers) in response to increased electricity demand from new technologies such as electric vehicles. By storing energy during periods of low demand and then releasing that energy at times of high demand, the peak demand of a given LV substation on the grid can be reduced therefore mitigating or at least delaying the need for replacement and upgrade. However, existing research into this application of BESS tends to evaluate the aggregated impact of such systems at the substation level and does not systematically consider the impact of the location and configuration of BESS on the voltage profiles, losses and utilisation within a given feeder. In this paper, four configurations of BESS are considered: single-phase, unlinked three-phase, linked three-phase without storage for phase-balancing only, and linked three-phase with storage. These four configurations are then assessed based on models of two real LV networks. In each case, the impact of the BESS is systematically evaluated at every node in the LV network using Matlab linked with OpenDSS. The location and configuration of a BESS is shown to be critical when seeking the best overall network impact or when considering specific impacts on voltage, losses, or utilisation separately. Furthermore, the paper also demonstrates that phase-balancing without energy storage can provide much of the gains on unbalanced networks compared to systems with energy storage.

Hollow-fiber liquid-phase microextraction of amphetamine-type stimulants in human hair samples

A fast method was optimized and validated in order to quantify amphetamine-type stimulants (amphetamine, AMP; methamphetamine, MAMP; fenproporex, FPX; 3,4-methylenedioxymethamphetamine, MDMA; and 3,4-methylenedioxyamphetamine, MDA) in human hair samples. The method was based in an initial procedure of decontamination of hair samples (50 mg) with dichloromethane, followed by alkaline hydrolysis and extraction of the amphetamines using hollow-fiber liquid-phase micro extraction (HF-LPME) in the three-phase mode. Gas chromatography-mass spectrometry (GC-MS) was used for identification and quantification of the analytes. The LoQs obtained for all amphetamines (around 0.05 ng/mg) were below the cut-off value (0.2 ng/mg) established by the Society of Hair Testing (SoHT). The method showed to be simple and precise. The intra-day and inter-day precisions were within 10.6% and 11.4%, respectively, with the use of only two deuteratecl internal standards (AMP-d5 and MDMA-d5). By using the weighted least squares linear regression (1/x(2)), the accuracy of the method was satisfied in the lower concentration levels (accuracy values better than 87%). Hair samples collected from six volunteers who reported regular use of amphetamines were submitted to the developed method. Drug detection was observed in all samples of the volunteers. (c) 2012 Elsevier B.V. All rights reserved.

Pollen analyses of sediment core GeoB9508-5

Millennial-scale dry events in the Northern Hemisphere monsoon regions during the last Glacial period are commonly attributed to southward shifts of the Intertropical Convergence Zone (ITCZ) associated with an intensification of the northeasterly (NE) trade wind system during intervals of reduced Atlantic meridional overturning circulation (AMOC). Through the use of high-resolution last deglaciation pollen records from the continental slope off Senegal, our data show that one of the longest and most extreme droughts in the western Sahel history, which occurred during the North Atlantic Heinrich Stadial 1 (HS1), displayed a succession of three major phases. These phases progressed from an interval of maximum pollen representation of Saharan elements between ~19 and 17.4 kyr BP indicating the onset of aridity and intensified NE trade winds, followed by a millennial interlude of reduced input of Saharan pollen and increased input of Sahelian pollen, to a final phase between ~16.2 and 15 kyr BP that was characterized by a second maximum of Saharan pollen abundances. This change in the pollen assemblage indicates a mid-HS1 interlude of NE trade wind relaxation, occurring between two distinct trade wind maxima, along with an intensified mid-tropospheric African Easterly Jet (AEJ) indicating a substantial change in West African atmospheric processes. The pollen data thus suggest that although the NE trades have weakened, the Sahel drought remained severe during this time interval. Therefore, a simple strengthening of trade winds and a southward shift of the West African monsoon trough alone cannot fully explain millennial-scale Sahel droughts during periods of AMOC weakening. Instead, we suggest that an intensification of the AEJ is needed to explain the persistence of the drought during HS1. Simulations with the Community Climate System Model indicate that an intensified AEJ during periods of reduced AMOC affected the North African climate by enhancing moisture divergence over the West African realm, thereby extending the Sahel drought for about 4000 years.

A converter compensator for power factor control in 3-phase induction machines

The advent of the harmonic neutralised shunt Converter Compensator as a practical means of reactive power compensation in power transmission systems has cleared ground for wider application of this type of equipment. An experimental 24-pulse voltage sourced convector has been successfully applied in controlling the terminal power factor of a 1.5kW, 240V three phase cage rotor induction motor, whose winding has been used in place of the usual phase shifting transformers. To achieve this, modifications have been made to the conventional stator winding of the induction machine. These include an unconventional phase spread and facilitation of compensator connections to selected tapping points between stator coils to give a three phase winding with a twelve phase connection to the twenty four pulse converter. Theoretical and experimental assessments of the impact of these modifications and attachment of the compensator have shown that there is a slight reduction in the torque developed at a given slip and in the combined system efficiency. There is also an increase in the noise level, also a consequence of the harmonics. The stator leakage inductance gave inadequate coupling reactance between the converter and the effective voltage source, necessitating the use of external inductors in each of the twelve phases. The terminal power factor is fully controllable when the induction machine is used either as a motor or as a generator.

Fuzzy risk index for power transformer failures due to external short-circuits

A novel methodology to assess the risk of power transformer failures caused by external faults, such as short-circuit, taking the paper insulation condition into account, is presented. The risk index is obtained by contrasting the insulation paper condition with the probability that the transformer withstands the short-circuit current flowing along the winding during an external fault. In order to assess the risk, this probability and the value of the degree of polymerization of the insulating paper are regarded as inputs of a type-2 fuzzy logic system (T2-FLS), which computes the fuzzy risk level. A Monte Carlo simulation has been used to find the survival function of the currents flowing through the transformer winding during a single-phase or a three-phase short-circuit. The Roy Billinton Test System and a real power system have been used to test the results. (C) 2008 Elsevier B.V. All rights reserved.

Redução do tempo de montagem final de transformadores CORE através da aplicação de ferramentas LEAN

Dissertação de mestrado em Engenharia Industrial

Late mesozoic to neogene radiolarian biostratigraphy and palaeoceanography in the Caribbean and East pacific region

^Raduolarians constitute a good tool for contributing to the biostratigraphy of accreted terranes and in deep-sea sediment sequences. The use of radiolarians is also proven to be valuable as a palaeoceanographic indicator. The present study evaluates radiolarians in three different geological settings, in order to better constrain the age of the sites and to try to understand their palaeoenvironmental situation at different periods, particularly in the Caribbean-Central America area. On the Jarabacoa Block, in Central Dominican Republic, a hundred meters of siliceous mudstones (Pedro Brand section in the Tireo Group) was dated as Turonian- Coniancian in age using radiolarians. A 40Ar-39Ar whole rock age of 75.1±1.1 Ma (Campanian), obtained in a basalt dyke crosscutting the radiolarian bearing rocks, a consistent minimum age for the pelagic-hemipelagic Pedro Brand section. The Jarabacoa Block is considered as the most complete outcrop section of Pacific ocean crust overlain by a first Aptian-Albian phase of Caribbean Large Igneous Province-type activity (CLIP), followed by the development of a Cenomanian-Santonian intraoceanic arc, which is in turn overlain by a late Campanian-Maastrichtian CLIP-phase. The Tireo Group records an episode of pelagic to hemi-pelagic and intermediate to acidic arc-derived sedimentation, previous to the youngest magmatic phase of the CLIP. Thus, the section of Pedro Brand has been interpreted in this study as being part of the intraoceanic arc. In northern Venezuela, a greenish radiolarite section from Siquisique Ophiolite (basalts, gabbros and some associated cherts) in Guaparo Creek has been studied. In previous studies, the Ophiolite unit (Petacas Creek section) has been dated as Bajocian-Bathonian, based on ammonites present in interpillow sediments from basalt blocks. New dating of the present study concluded in an Aptian?-Albian-Cenomanian age for the Guaparo creek section (middle Cretaceous), based on radiolarian assemblage associated to basalts-gabbros rocks of the unit. Previous plagioclase 40Ar-39Ar ages from the Siquisuique Ophiolite may be slightly younger (94-90 Ma.) and may, therefore, represent younger dykes that intruded onto a well-developed sheeted dyke complex of the Siquisique. The geochemistry of these rocks and the palaeotectonic reconstruction of the Caribbean area during this period suggest that these rocks were derived from a mid-ocean ridge with an influence of deep mantle plume. The Siquisique Ophiolite most probably represents a fragment of the proto-Caribbean basin. The Integrated Ocean Drilling Program Expedition 344 drilled a transect across the convergent margin off Costa Rica. Two sites of this expedition were chosen for radiolarian biostratigraphy and palaeoceanographic studies. Both sites (U1381C and U1414A) are located in the incoming Cocos plate, in the eastern Equatorial Pacific. The succession of U1381C yields a Middle Miocene to Pleistocene age, and presents an important hiatus of approximately 10 Ma. The core of U1414A exposes a continuous sequence that deposited during Late Miocene to Pleistocene (radiolarian zones RN6-RN16). The ages were assigned based on radiolarians and correlated with nannofossil zonation and tephra 40Ar-39Ar datation. With those results, and considering the northward movement of the Cocos plate motion (about 7 cm/year), deduction is made that the sites U1381C and U1414A were initially deposited during the Miocene, several hundreds of kilometres from the current location, slightly south of the Equator. This suggests that the faunas of these sites have been subjected to different currents, first influenced by the cold tongue of the South Equatorial Current and followed by the warm Equatorial Countercurrent. At last, coastal upwelling influenced faunas of the Pleistocene. -- Les radiolaires sont considérés comme un outil utile à la biostratigraphie des terrains accrétés et des sédiments profonds. Leur utilité est aussi prouvée comme étant remarquable au niveau des reconstructions paléocéanographiques. La présente étude évalue l'importance et la présence des radiolaires de trois localités géologiquement différentes d'Amérique Centrale-Caraïbes, dans le but d'améliorer les model d'âges et de mieux comprendre la situation paléoenvironnementale à travers le temps. Dans le Bloque de Jarabacoa, au centre de la République Dominicaine, une section de cent mètres (section de Pedro Brand, Groupe de Tireo) a été datée comme faisant partie du Turonien-Santonien, en utilisant les radiolaires. Une datation 40Ar-39Ar sur roche totale de 75±1.1 Ma (Campanien) a été obtenu pour vin dyke traversant les sédiments riches en radiolaires, en cohérence avec l'âge minimum accordé à la section de Pedro Brand. Aux Caraïbes, le Bloque de Jarabacoa est considéré comme l'affleurement le plus complet présentant une succession de croûte océanique d'origine Pacifique recouverte d'une première phase d'activité volcanique de type CLIP (Caribbean Large Igneous Province) d'âge Aptien- Albien, de dépôts d'arc volcanique intra-océanique d'âge Cénomanien-Santonien, puis d'une seconde phase de type CLIP d'âge Campanien-Maastrichtien. Le Groupe de Tireo enregistre un épisode de dépôt pélagiques-hémipélagiques et d'arc volcanique, antérieur à la plus jeune phase de type CLIP. Cette étude place donc la formation de la section de Pedro Brand au moment du développement de l'arc intra-océanique. A Guaparo Creek (nord du Vénézuela), une section de radiolarite verdâtre faisant partie des ophiolites de Siquisique (basaltes, gabbros, cherts) a été étudiée. Dans des études précédentes, sur la localité de Petacas Creek, l'unité ophiolitique a été daté d'âge Bajocien- Bathonien (Jurassique) sur la base d'ammonites trouvées dans des sédiments intercalés entre des laves en coussins. Les nouvelles datations de notre étude, basées sur des assemblages à radiolaires de l'unité à basaltes-gabbros, donnent un âge Aptien?-Albien-Cénomanien (Crétacé moyen). Les âges de l'Ophiolite de Siquisique, précédement calculés par la méthode sur plagioclases, pourraient être légèrement plus jeune (94-90 Ma) et donc représenter des intrusions plus récentes de dykes dans le complexe filonien déjà bien dévelopé. La géochimie de ces roches magmatiques, ainsi que les reconstructions paléotectoniques de la zone Caraïbes durant cette période, suggèrent que ces formations sont dérivées d'une ride médio-océanique associée à l'influence d'un panache mantellique. L'ophiolite de Siquisique représente très probablement un fragment du bassin de proto¬Caraïbe. L'expédition 344 du programme IODP (Integrated Ocean Drilling Program) a eu lieu dans l'optique de forer et dresser une coupe de la marge convergente au large du Costa Rica. Deux sites de cette expédition ont été choisis pour les besoins des études de biostratigraphie et de reconstruction paléocéanographique. Ces deux sites (U1381C et U1414A) sont situés sur la plaque subductante de Cocos, dans la zone Pacifique est-équatoriale. La carotte U1381C expose une séquence s'étalant du Miocène moyen au Pléistocène, et présente un important hiatus d'environ 10 Ma. La carotte U1414A expose une séquence continue s'étalant du Miocène tardif au Pléistocène (zone à radiolaires RN6-RN16). Les âges ont été assignés sur la base des radiolaires et corrélés avec les zones à nanofossiles et les datations 40Ar-39Ar sur téphras. Avec ces résultats, et en considérant le mouvement nord de la plaque de Cocos (environ 7 cm/an), déduction est faite que les deux sites étaient initialement situés, au cours du Miocène, à plusieurs centaines de kilomètres de leur location actuelle, au sud de l'équateur. Cela suggère que les faunes de ces sites ont été sujettes à différents courants; premièrement influencées par la langue froide du SEC (South Equatorial Current), puis par les eaux chaudes du ECC (Equatorial Countercurrent). Pour terminer, les remontées d'eau côtières ont influencées les faunes Pléistocène.

Transformers 3

A 36 minute covering transformer testing, use in three-phase connections and power systems by Prof Jan Sykulski of the University of Southampton.

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Distribution transformers modeling with angular displacement: actual values and per unit analysis

In this work a detailed modeling of three-phase distribution transformers aimed at complementing well-known approaches is presented. Thus, incidence of angular displacement and tapping is taken into account in the proposed models, considering both actual values and per unit. The analysis is based on minimal data requirement: solely short-circuit admittance is needed since three-phase transformers are treated as non-magnetically-coupled single-phase transformers. In order to support the proposed methodology, results obtained through laboratory tests are presented.

Generalised single-equation load flow method for unbalanced distribution systems

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)