Mass-splittings of doubly heavy baryons in QCD

We consider (for the first time) the ratios of doubly heavy baryon masses (spin 3/2 over spin 1/2 and SU(3) mass-splittings) using double ratios of sum rules (DRSR), which are more accurate than the usual simple ratios often used in the literature for getting the hadron masses. In general, our results agree and compete in precision with potential model predictions. In our approach, the alpha(s) corrections induced by the anomalous dimensions of the correlators are the main sources of the Xi(QQ)*-Xi(QQ) mass-splittings, which seem to indicate a 1/M(Q) behaviour and can only allow the electromagnetic decay Xi(QQ)* -> Xi(QQ) + gamma but not to Xi(QQ) + pi. Our results also show that the SU(3) mass-splittings are (almost) independent of the spin of the baryons and behave approximately like 1/M(Q), which could be understood from the QCD expressions of the corresponding two-point correlator. Our results can improved by including radiative corrections to the SU(3) breaking terms and can be tested, in the near future, at Tevatron and LHCb. (C) 2010 Published by Elsevier B.V.

Transfer reactions in the investigation of light-nuclei nucleosynthesis

Cross sections for the (6)Li(p,gamma)(7)Be, (7)Li(n,gamma)(8)Li (8)Li(n,gamma)(9)Li and (8)Li(p,gamma)(9)Be capture reactions have been investigated in the framework of the potential model. The main ingredients of the potential model are the potentials used to generate the continuum and bound-state wave functions and spectroscopic factors of the corresponding bound systems. The spectroscopic factors for the (7)Li circle times n=(8)Li(gs), (8)Li circle times n=(9)Li(gs) bound systems were obtained from a FR-DWBA analysis of neutron transfer reactions induced by (8)Li radioactive beam on a (9)Be target, while spetroscopic factor for the (8)Li circle times n=(9)Be(gs) bound system were obained from a proton transfer reaction. From the obtained capture reaction cross section, reaction rate for the (8)Li(n,gamma)(9)Li and (8)Li(p,gamma)(9)Be direct neutron and proton capture were determined and compared with other experimental and calculated values.

The low-lying electronic states of BeAs: a first principles characterization

The electronic structure and spectroscopic properties of a manifold of states of a new molecular species, BeAs, have been investigated theoretically at the complete active space self-consistent field/multireference single and double excitations configuration interaction (CASSCF/MRSDCI) approach, using the aug-cc-pV5Z-PP basis set for arsenic, which includes a relativistic effective core potential, and the cc-pV5Z set for beryllium. Potential energy curves of five quartet and eight doublet (I > + S) states correlating with the five lowest-lying dissociation limit are constructed. The effect of spin-orbit coupling is also included in the description of the ground state, and of the doublet states correlating with the second dissociation channel. Dipole moment functions and vibrationally averaged dipole moments are also evaluated. The similarities and differences between BeAs, BeP, and BeN are analyzed. Spin-orbit effects are small for the ground state close to the equilibrium distance, but avoided crossings between Omega = 1/2 states, and between Omega = 3/2 states changes significantly the I > + S curves for the lowest-lying doublets.

In situ synchrotron SAXS study of polymerizable microemulsions

We present for the first time a real-time small-angle X-ray scattering (SAXS) study of the structural transition of fluid microemulsion to solid polymerized material in a silicone polymerizable microemulsion system. A reactive methacrylate-terminated siloxane macromonomer (MTSM, Mn ∼ 1000 g/mol) was synthesized and used for microemulsion formulations comprising MTSM (oil phase), water, and a mixture of nonionic surfactant (Teric G9A8) with isopropanol. In situ synchrotron SAXS was used to investigate time-dependent nanostructure evolution during the polymerization reaction, which was directly initiated by X-ray radiation. The SAXS data were analyzed using both the Teubner-Strey model and the core-shell model. The results obtained by the Teubner-Strey model showed that the domain size (d) decreased while the correlation length (ξ) increased upon polymerization. The analysis in terms of the core-shell model displayed that adding water to the precursor microemulsion caused the water droplets to start swelling, which resulted in the discontinuity of water in oil microemulsion. There exhibited large differences in morphologies of polymerized materials from the microemulsion formulations with different water and surfactant contents. The core and shell sizes of water droplets decreased during the course of polymerization when there was 15 wt % or more water in the microemulsion formulation; the polymerized material thus exhibited increasingly discrete granular morphology. When there was 10 wt % or less water content in the precursor microemulsion, the rearrangement of water domains could be minimized during the course of polymerization and transparent polymerized material was obtained.

Redes-em-chip de baixo custo

Com as recentes tecnologias de fabricação é possível integrar milhões de transistores em um único chip, permitindo a criação dos chamados System-on-Chip (SoCs), que integram em um único chip um grande número de componentes (tipicamente blocos reutilizáveis conhecidos por núcleos). Quanto mais complexos forem estes sistemas, melhores técnicas de projeto serão necessárias para também reduzir o tempo e custo do projeto. Uma destas técnicas, chamada de Network-on-Chip (NoC), permite melhorar a performance da comunicação entre os núcleos e, ao mesmo tempo, fornecer uma plataforma de comunicação escalável e que pode ser reutilizada para um grande número de sistemas. Uma NoC pode ser definida como uma estrutura de roteadores e canais ponto-a-ponto que interconectam os núcleos de um sistema, provendo o suporte de comunicação entre eles. Os dados são transmitidos pela rede na forma de mensagens, que podem ser divididas em unidades menores chamadas de pacote. Uma das desvantagens desta plataforma de comunicação é o impacto na área do sistema causado pelos roteadores. Dentro deste contexto, este trabalho apresenta uma arquitetura de roteador de baixo custo, com o objetivo de permitir o uso de NoCs em sistemas onde a área do roteador representará um grande impacto no custo do sistema. A arquitetura deste roteador, chamado de Tonga, é baseada em um roteador chamado RASoC, um soft-core para SoCs. Nesta dissertação será apresentada também uma rede heterogênea, baseada na rede SoCIN, e composta por dois tipos de roteadores – RASoC e Tonga. Estes roteadores visam diferentes objetivos: Rasoc alcança uma maior performance comparada ao Tonga, mas ocupa área consideravelmente maior. Potencialmente, uma NoC heterogênea otimizada pode ser desenvolvida combinando estes roteadores, procurando o melhor compromisso entre área e latência. Os modelos desenvolvidos permitem a estimativa de área e do desempenho das arquiteturas de comunicação propostas e são apresentados resultados de performance para algumas aplicações.

Implementação em hardware de uma Rede Neuronal com ummicroprocessador embebido em FPGA

O objectivo deste trabalho é a implementação em hardware de uma Rede Neuronal com um microprocessador embebido, podendo ser um recurso valioso em várias áreas científicas. A importância das implementações em hardware deve-se à flexibilidade, maior desempenho e baixo consumo de energia. Para esta implementação foi utilizado o dispositivo FPGA Virtex II Pro XC2VP30 com um MicroBlaze soft core, da Xilinx. O MicroBlaze tem vantagens como a simplicidade no design, sua reutilização e fácil integração com outras tecnologias. A primeira fase do trabalho consistiu num estudo sobre o FPGA, um sistema reconfigurável que possui características importantes como a capacidade de executar em paralelo tarefas complexas. Em seguida, desenvolveu-se o código de implementação de uma Rede Neuronal Artificial baseado numa linguagem de programação de alto nível. Na implementação da Rede Neuronal aplicou-se, na camada escondida, a função de activação tangente hiperbólica, que serve para fornecer a não linearidade à Rede Neuronal. A implementação é feita usando um tipo de Rede Neuronal que permite apenas ligações no sentido de saída, chamado Redes Neuronais sem realimentação (do Inglês Feedforward Neural Networks - FNN). Como as Redes Neuronais Artificiais são sistemas de processamento de informações, e as suas características são comuns às Redes Neuronais Biológicas, aplicaram-se testes na implementação em hardware e analisou-se a sua importância, a sua eficiência e o seu desempenho. E finalmente, diante dos resultados, fez-se uma análise de abordagem e metodologia adoptada e sua viabilidade.

Effective theory for trapped few-fermion systems

We apply the general principles of effective field theories to the construction of effective interactions suitable for few- and many-body calculations in a no-core shell model framework. We calculate the spectrum of systems with three and four two-component fermions in a harmonic trap. In the unitary limit, we find that three-particle results are within 10% of known semianalytical values even in small model spaces. The method is very general, and can be readily extended to other regimes, more particles, different species (e.g., protons and neutrons in nuclear physics), or more-component fermions (as well as bosons). As an illustration, we present calculations of the lowest-energy three-fermion states away from the unitary limit and find a possible inversion of parity in the ground state in the limit of trap size large compared to the scattering length. Furthermore, we investigate the lowest positive-parity states for four fermions, although we are limited by the dimensions we can currently handle in this case.

Glueballs as intermediate states in hadronic transitions

Hadronic transitions rates in the heavy quarkonium systems are calculated within the framework of the QCD multipole expansion. The spectrum of glueballs consisting of two massive gluons, obtained by the use of the potential model, is adopted as a suitable description of the intermediate states. Comparisons with the quark confining string model (QCS) and the bag model are made. © 1990 Springer-Verlag.

Coeficientes de perda de carga em valvulas e acessorios no escoamento laminar de fluidos nao-Newtonianos

Friction loss coefficients for laminar flow of xantan gum solutions (concentrations in the range of 0.1-0.5% by weight) through valves and fittings were experimentally determined. The rheological behavior, studied by means of a concentric cylinder rheometer, was pseudoplastic, being well described by the Ostwald-De Waele model with non-linear correlation coefficients (r) between 0.998 and 0.999. In the pressure drop measurements the following fittings were employed: completely open and half way open ball valve, completely open and half way open angle valve, tee used like coupling, tee used like a 90° elbow, short radius 90° elbow and coupling. The results showed that the friction loss coefficients increased with decreasing generalized Reynolds number. The friction loss coefficients could be well adjusted by a potential model, suggested by Kittredge & Rowley (1957) for Newtonian fluids, K f = A(Re g) -B, with correlation coefficients between 0.837 and 0.999.

Modeling the growth of LT and TL-oriented fatigue cracks in longitudinally and transversely pre-strained Al 2524-T3 alloy

The aluminum alloy 2524 (Al-Cu-Mg) was developed during the 90s mainly to be employed in aircraft fuselage panels, replacing the standard Al 2024. In the present analysis the fatigue crack growth (FCG) behavior of 2524-T3 was investigated, regarding the influence of three parameters: load ratio, pre strain and crack plane orientation of the material. The pre strain of aluminum alloys is usually performed in order to obtain a more homogeneous precipitates distribution, accompanied by an increase in the yield strength. In this work, it was evaluated the resistance of Al 2524-T3 sheet samples to the fatigue crack growth, having L-T and T-L crack orientations. FCG tests were performed under constant amplitude loading at three distinct positive load ratios. The three material conditions were tested: as received(AR), pre strained longitudinally (SL) and transversally (ST) in relation to rolling direction. In order to describe FCG behavior, two-parameter kinetic equations were compared: a Paris-type potential model and a new exponential equation introduced in a previous work conducted by our research group. It was observed that the exponential model, which takes into account the deviations from linearity presented by da/dN versus AK data, describes more adequately the FCG behavior of Al 224-T3 in relation to load ratio, pre strain effects and crack plane orientation. © 2011 Published by Elsevier Ltd.

Universality in Four-Boson Systems

We report recent advances on the study of universal weakly bound four-boson states from the solutions of the Faddeev-Yakubovsky equations with zero-range two-body interactions. In particular, we present the correlation between the energies of successive tetramers between two neighbor Efimov trimers and compare it to recent finite range potential model calculations. We provide further results on the large momentum structure of the tetramer wave function, where the four-body scale, introduced in the regularization procedure of the bound state equations in momentum space, is clearly manifested. The results we are presenting confirm a previous conjecture on a four-body scaling behavior, which is independent of the three-body one. We show that the correlation between the positions of two successive resonant four-boson recombination peaks are consistent with recent data, as well as with recent calculations close to the unitary limit. Systematic deviations suggest the relevance of range corrections. © 2012 Springer-Verlag.

Avaliação da expressão proteica de PTEN, MDM2, P53 e AR em lesões proliferativas da próstata canina

Pós-graduação em Medicina Veterinária - FCAV

Mass spectra of glueballs and hybrids

Assuming massive constituent gluons the mass spectroscopy of glueballs and hybrids is analysed in the framework of the potential model. Only pairwise potentials are considered.

Calculation of the eigenfunctions of the two-group neutron diffusion equation and application to modal decomposition of BWR instabilities

In this thesis, numerical methods aiming at determining the eigenfunctions, their adjoint and the corresponding eigenvalues of the two-group neutron diffusion equations representing any heterogeneous system are investigated. First, the classical power iteration method is modified so that the calculation of modes higher than the fundamental mode is possible. Thereafter, the Explicitly-Restarted Arnoldi method, belonging to the class of Krylov subspace methods, is touched upon. Although the modified power iteration method is a computationally-expensive algorithm, its main advantage is its robustness, i.e. the method always converges to the desired eigenfunctions without any need from the user to set up any parameter in the algorithm. On the other hand, the Arnoldi method, which requires some parameters to be defined by the user, is a very efficient method for calculating eigenfunctions of large sparse system of equations with a minimum computational effort. These methods are thereafter used for off-line analysis of the stability of Boiling Water Reactors. Since several oscillation modes are usually excited (global and regional oscillations) when unstable conditions are encountered, the characterization of the stability of the reactor using for instance the Decay Ratio as a stability indicator might be difficult if the contribution from each of the modes are not separated from each other. Such a modal decomposition is applied to a stability test performed at the Swedish Ringhals-1 unit in September 2002, after the use of the Arnoldi method for pre-calculating the different eigenmodes of the neutron flux throughout the reactor. The modal decomposition clearly demonstrates the excitation of both the global and regional oscillations. Furthermore, such oscillations are found to be intermittent with a time-varying phase shift between the first and second azimuthal modes.

Studio parametrico del comportamento di opere di sostegno flessibili mediante modellazione numerica

Oggetto di questa tesi è lo studio parametrico del comportamento di paratie mediante modellazione numerica agli elementi finiti. Si è anche analizzato l’aspetto normativo relativo ad esse ed in particolare si è applicato il D.M. 2008 ad una paratia sottolineando le innovazioni nella progettazione geotecnica. Le paratie sono opere di sostegno flessibili interagenti con i fronti di scavo e costituite da una porzione fuori terra, soggetta a condizioni di spinta attiva, e una porzione interrata che contrappone la resistenza passiva del terreno. Le opere di sostegno flessibile si dividono in due categorie: diaframmi e palancole che differiscono molto fra loro sia per il materiale con cui sono realizzate, sia per la tecnica di messa in opera, sia per la geometria, ma hanno in comune il meccanismo di funzionamento. Sono stati illustrati i metodi di calcolo per lo studio delle paratie: metodi dell’equilibrio limite a rottura, metodi a molle e metodi agli elementi finiti. I metodi agli elementi finiti negli ultimi anni hanno avuto maggior successo grazie alla possibilità di definire il modello costitutivo sforzi-deformazioni, le condizioni al contorno e le condizioni iniziali. Esistono numerosi programmi di calcolo che si basano sul metodo agli elementi finiti, tra i quali è da annoverare il programma Plaxis che viene molto usato grazie alla presenza di vari modelli costitutivi in grado di simulare il comportamento del terreno. Tra i legami costitutivi presenti nel programma Plaxis, sono stati presi in esame il modello Mohr-Coulomb, l’Hardening model e il Soft Soil Creep model e sono poi stati applicati per eseguire uno studio parametrico del comportamento delle paratie. Si è voluto comprendere la sensibilità dei modelli al variare dei parametri inseriti nel programma. In particolare si è posta attenzione alla modellazione dei terreni in base ai diversi modelli costitutivi studiando il loro effetto sui risultati ottenuti. Si è inoltre eseguito un confronto tra il programma Plaxis e il programma Paratie. Quest’ultimo è un programma di calcolo che prevede la modellazione del terreno con molle elasto-plastiche incrudenti. Il lavoro di tesi viene illustrato in questo volume come segue: nel capitolo 1 si analizzano le principali caratteristiche e tipologie di paratie mettendo in evidenza la complessità dell’analisi di queste opere e i principali metodi di calcolo usati nella progettazione, nel capitolo 2 si è illustrato lo studio delle paratie secondo le prescrizioni del D.M. 2008. Per comprendere l’argomento è stato necessario illustrare i principi base di questo decreto e le caratteristiche generali del capitolo 6 dedicato alla progettazione geotecnica. Le paratie sono poi state studiate in condizioni sismiche secondo quanto previsto dal D.M. 2008 partendo dall’analisi degli aspetti innovativi nella progettazione sismica per poi illustrare i metodi pseudo-statici utilizzati nello studio delle paratie soggette ad azione sismica. Nel capitolo 3 si sono presi in esame i due programmi di calcolo maggiormente utilizzati per la modellazione delle paratie: Paratie e Plaxis. Dopo aver illustrato i due programmi per comprenderne le potenzialità, i limiti e le differenze, si sono analizzati i principali modelli costituitivi implementati nel programma Plaxis, infine si sono mostrati alcuni studi di modellazione presenti in letteratura. Si è posta molta attenzione ai modelli costitutivi, in particolare a quelli di Mohr-Coulomb, Hardening Soil model e Soft Soil Creep model capaci di rappresentare il comportamento dei diversi tipi di terreno. Nel capitolo 4, con il programma Plaxis si è eseguita un’analisi parametrica di due modelli di paratie al fine di comprendere come i parametri del terreno, della paratia e dei modelli costitutivi condizionino i risultati. Anche in questo caso si è posta molta attenzione alla modellazione del terreno, aspetto che in questa tesi ha assunto notevole importanza. Dato che nella progettazione delle paratie è spesso utilizzato il programma Paratie (Ceas) si è provveduto ad eseguire un confronto tra i risultati ottenuti con questo programma con quelli ricavati con il programma Plaxis. E’ stata inoltra eseguita la verifica della paratia secondo le prescrizioni del D.M. 2008 dal momento che tale decreto è cogente.