Alleviation of chronic venous leg ulcers with a hand-held dielectric barrier discharge plasma generator (PlasmaDerm(®) VU-2010): results of a monocentric, two-armed, open, prospective, randomized and controlled trial (NCT01415622).

BACKGROUND Cold atmospheric plasma (CAP, i.e. ionized air) is an innovating promising tool in reducing bacteria. OBJECTIVE We conducted the first clinical trial with the novel PlasmaDerm(®) VU-2010 device to assess safety and, as secondary endpoints, efficacy and applicability of 45 s/cm(2) cold atmospheric plasma as add-on therapy against chronic venous leg ulcers. METHODS From April 2011 to April 2012, 14 patients were randomized to receive standardized modern wound care (n = 7) or plasma in addition to standard care (n = 7) 3× per week for 8 weeks. The ulcer size was determined weekly (Visitrak(®) , photodocumentation). Bacterial load (bacterial swabs, contact agar plates) and pain during and between treatments (visual analogue scales) were assessed. Patients and doctors rated the applicability of plasma (questionnaires). RESULTS The plasma treatment was safe with 2 SAEs and 77 AEs approximately equally distributed among both groups (P = 0.77 and P = 1.0, Fisher's exact test). Two AEs probably related to plasma. Plasma treatment resulted in a significant reduction in lesional bacterial load (P = 0.04, Wilcoxon signed-rank test). A more than 50% ulcer size reduction was noted in 5/7 and 4/7 patients in the standard and plasma groups, respectively, and a greater size reduction occurred in the plasma group (plasma -5.3 cm(2) , standard: -3.4 cm(2) ) (non-significant, P = 0.42, log-rank test). The only ulcer that closed after 7 weeks received plasma. Patients in the plasma group quoted less pain compared to the control group. The plasma applicability was not rated inferior to standard wound care (P = 0.94, Wilcoxon-Mann-Whitney test). Physicians would recommend (P = 0.06, Wilcoxon-Mann-Whitney test) or repeat (P = 0.08, Wilcoxon-Mann-Whitney test) plasma treatment by trend. CONCLUSION Cold atmospheric plasma displays favourable antibacterial effects. We demonstrated that plasma treatment with the PlasmaDerm(®) VU-2010 device is safe and effective in patients with chronic venous leg ulcers. Thus, larger controlled trials and the development of devices with larger application surfaces are warranted.

Small quantity but large effect — How minor phases control strain localization in upper mantle shear zones

Low viscosity domains such as localized shear zones exert an important control on the geodynamics of the uppermost mantle. Grain size reduction and subsequent strain localization related to a switch from dislocation to diffusion creep is one mechanism to form low viscosity domains. To sustain strain localization, the grain size of mantle minerals needs to be kept small over geological timescales. One way to keep olivine grain sizes small is by pinning of mobile grain boundaries during grain growth by other minerals (second phases). Detailed microstructural studies based on natural samples from three shear zones formed at different geodynamic settings, allowed the derivation of the olivine grain-size dependence on the second-phase content. The polymineralic olivine grain-size evolution with increasing strain is similar in the three shear zones. If the second phases are to pin the mobile olivine grain boundary the phases need to be well mixed before grain growth. We suggest that melt-rock and metamorphic reactions are crucial for the initial phase mixing in mantle rocks. With ongoing deformation and increasing strain, grain boundary sliding combined with mass transfer processes and nucleation of grains promotes phase mixing resulting in fine-grained polymineralic mixtures that deform by diffusion creep. Strain localization due to the presence of volumetrically minor minerals in polymineralic mantle rocks is only important at high strain deformation (ultramylonites) at low temperatures (<~800°C). At smaller strain and stress conditions and/or higher temperatures other parameters like overall energy available to deform a given rock volume, the inheritance of mechanical anisotropies or the presence of water or melts needs to be considered to explain strain localization in the upper mantle.

Reduced serum chemerin in patients with more severe liver cirrhosis

Chemerin is a well-established modulator of immune cell function and its serum levels are induced in inflammatory diseases. Liver cirrhosis is associated with inflammation which is aggravated by portal hypertension. The objective of this study was to evaluate whether chemerin is induced in patients with more severe liver cirrhosis and portal hypertension. Chemerin has been measured by ELISA in the portal venous serum (PVS), systemic venous serum (SVS) and hepatic venous serum (HVS) of 45 patients with liver cirrhosis. Chemerin is higher in HVS compared to PVS in accordance with our recently published finding. SVS, HVS and PVS chemerin decline in patients with more advanced liver injury defined by the CHILD-PUGH score. Hepatic chemerin has been determined in a small cohort and is similarly expressed in normal and cirrhotic liver. MELD score and serum markers of liver and kidney function do not correlate with chemerin. There is a positive correlation of chemerin in all compartments with Quick prothrombin time and of SVS chemerin with systolic blood pressure. PVS chemerin is induced in patients with modest/massive ascites but this does not translate into higher HVS and SVS levels. Chemerin is not associated with variceal size. Reduction of portal pressure by transjugular intrahepatic portosystemic shunt does not affect chemerin levels. These data show that low chemerin in patients with more severe liver cirrhosis is associated with reduced Quick prothrombin time.

Maastrichtian calcareous nannofossils of the Indian Ocean and Shatsky Rise

The biotic effects of volcanism have long been the unknown factors in creating biotic stress, and the contribution of the Deccan volcanism to the K-T mass extinction remains largely unknown. Detailed studies of the volcanic-rich sediments of Indian Ocean Ninetyeast Ridge Sites 216 and 217 and Wharton Basin Site 212 reveal that the biotic effects of late Maastrichtian volcanism on planktic foraminifera and calcareous nannofossils are locally as severe as those of the K-T mass extinction. The biotic expressions of these high stress environments are characterized by the Lilliput effect, which includes reduced diversity by eliminating most K-strategy species, and reduction in specimen size (dwarfing), frequently to less than half their normal adult size of both r-strategy and surviving K-strategy species. In planktic foraminifera, the most extreme biotic stress results are nearly monospecific assemblages dominated by the disaster opportunist Guembelitria, similar to the aftermath of the K-T mass extinction. The first stage of improving environmental conditions results in dominance of dwarfed low oxygen tolerant Heterohelix species and the presence of a few small r-strategy species (Hedbergella, Globigerinelloides). Calcareous nannofossil assemblages show similar biotic stress signals with the dominance of Micula decussata, the disaster opportunist, and size reduction in the mean length of subordinate r-strategy species particularly in Arkhangelskiella cymbiformis and Watznaueria barnesiae. These impoverished and dwarfed late Maastrichtian assemblages appear to be the direct consequences of mantle plume volcanism and associated environmental changes, including high nutrient influx leading to eutrophic and mesotrophic waters, low oxygen in the water column and decreased watermass stratification.

Whole rock and elements concentrations from IODP Hole 343-C0019E

The microstructures, mineralogy and chemistry of four representative samples collected from cores extracted from the Japan Trench during Integrated Ocean Drilling Project Expedition 343, the Japan Trench Fast Drilling Project (JFAST) have been studied using optical microscopy, TEM, SEM, XRF, XRD and microprobe analyses. The samples provide a transect from relatively undeformed marine sediments in the hanging wall, to the undeformed footwall material, crossing the thrust interface between the Pacific and North American plate, where the fault slipped during the March 2011 Tohoku-Oki earthquake. Our preliminary results suggest that the low strength of JFAST fault gouge material is caused by the high amount of clay minerals (~ 60% smectite, ~ 14 illite). Clay minerals in the décollement (gouge) sample are partly replaced by newly formed manganese oxide, which precipitated from hydrothermal fluids. Dauphine twins were found in quartz grains of the décollement sample suggesting local high stress possible during seismic loading. Other microstructures cannot be assigned unambiguously to co-seismic or a-seismic faulting processes. The observed scaly clay fabric is consistent with observations in many other plate-boundary fault zones. Significant grain size reduction was found in the fault (decollement) zone sample. But a change in lithology of the fault material cannot be ruled out. Microstructures typical for a-seismic deformation like dissolution-precipitation features (e.g. dissolved grain boundaries, mineral alteration) occur in all JFAST core samples, but more frequently in the décollement sample.

Caracterización funcional de los genes sgb (suppressors of agb1-2 susceptibility to pathogens): Nuevos reguladores de la respuesta de inmunidad innata de Arabidopsis thaliana

Un porcentaje importante de las pérdidas de la producción agrícola se deben a las enfermedades que causan en los cultivos los hongos necrótrofos y vasculares. Para mejorar la productividad agrícola es necesario tener un conocimiento detallado de las bases genéticas y moleculares que regulan la resistencia de las plantas a este tipo de patógenos. En Arabidopsis thaliana la resistencia frente a patógenos necrótrofos, como el hongo Plectosphaerella cucumerina BMM (PcBMM), es genéticamente compleja y depende de la activación coordinada de distintas rutas de señalización, como las reguladas por las hormonas ácido salicílico (SA), ácido jasmónico (JA), etileno (ET) y ácido abscísico (ABA), así como de la síntesis de compuestos antimicrobianos derivados del Triptófano y de la integridad de la pared celular (Llorente et al., 2005, Hernández-Blanco et al., 2007; Delgado-Cerezo et al., 2012). Uno de los componentes claves en la regulación de la resistencia de las plantas a patógenos (incluidos hongos necrótrofos y biótrofos) es la proteína G heterotrimérica, un complejo proteico formado por tres subunidades (Gα, Gβ y Gγ), que también regula distintos procesos del desarrollo vegetal. En Arabidopsis hay un gen que codifica para la subunidad α (GPA1), otro para la β (AGB1), y tres genes para la subunidad γ (AGG1, AGG2 y AGG3). El complejo GPA1-AGB1-AGG (1-3) se activa y disocia tras la percepción de una señal específica, actuando el dímero AGB1-AGG1/2 como un monómero funcional que regula las respuestas de defensa (Delgado-Cerezo et al., 2012). Estudios transcriptómicos y análisis bioquímicos de la pared celular en los que se comparaban los mutantes agb1-2 y agg1 agg2, y plantas silvestres (Col-0) revelaron que la resistencia mediada por Gβ-Gγ1/2 no es dependiente de rutas de defensa previamente caracterizadas, y sugieren que la proteína G podría modular la composición/estructura (integridad) de la pared celular (Delgado-Cerezo et al., 2012). Recientemente, se ha demostrado que AGB1 es un componente fundamental de la respuesta inmune mediada por Pathogen- Associated Molecular Patterns (PTI), ya que los mutantes agb1-2 son incapaces de activar tras el tratamiento con PAMPs respuestas de inmunidad, como la producción de especies reactivas de oxígeno (ROS; Liu et al., 2013). Dada la importancia de la proteína G heterotrimérica en la regulación de la respuestas de defensa (incluida la PTI) realizamos un escrutinio de mutantes supresores de la susceptibilidad de agb1-2 al hongo necrótrofo, PcBMM, para identificar componentes adicionales de las rutas de señalización reguladas por AGB1. En este escrutinio se aislaron cuatro mutantes sgb (suppressors of agb1-2 susceptibility to pathogens), dos de los cuales, sgb10 y sgb11, se han caracterizado en la presente Tesis Doctoral. El mutante sgb10 es un segundo alelo nulo del gen MKP1 (At3g55270) que codifica la MAP quinasa-fosfatasa 1 (Bartels et al., 2009). Este mutante presenta lesiones espontáneas en plantas adultas y una activación constitutiva de las principales rutas de defensa (SA, JA y ET, y de metabolitos secundarios, como la camalexina), que explicaría su elevada resistencia a PcBMM y Pseudomonas syringae. Estudios epistáticos sugieren que la resistencia mediada por SGB10 no es dependiente, si no complementaria a la regulada por AGB1. El mutante sgb10 es capaz de restablecer en agb1-2 la producción de ROS y otras respuestas PTI (fosforilación de las MAPK6/3/4/11) tras el tratamiento con PAMPs tan diversos como flg22, elf18 y quitina, lo que demuestra el papel relevante de SGB10/MKP1 y de AGB1 en PTI. El mutante sgb11 se caracteriza por presentar un fenotipo similar a los mutantes irregular xylem (e.g. irx1) afectado en pared celular secundaria: irregularidades en las células xilemáticas, reducción en el tamaño de la roseta y altura de planta, y hojas con un mayor contenido de clorofila. La resistencia de sgb11 a PcBMM es independiente de agb1-2, ya que la susceptibilidad del doble mutante sgb11 agb1-2 es intermedia entre la de agb1-2 y sgb11. El mutante sgb11 no revierte la deficiente PTI de agb1-2 tras el tratamiento con flg22, lo que indica que está alterado en una ruta distinta de la regulada por SGB10. sgb11 presenta una sobreactivación de la ruta del ácido abscísico (ABA), lo que podría explicar su resistencia a PcBMM. La mutación sgb11 ha sido cartografiada en el cromosoma III de Arabidopsis entre los marcadores AthFUS6 (81,64cM) y nga6 (86,41cM) en un intervalo de aproximadamente 200 kb, que comprende genes, entre los que no se encuentra ninguno previamente descrito como IRX. El aislamiento y caracterización de SGB11 apoya la relevancia de la proteína G heterotrimérica en la regulación de la interconexión entre integridad de la pared celular e inmunidad. ABSTRACT A significant percentage of agricultural losses are due to diseases caused by necrotrophic and vascular fungi. To enhance crop yields is necessary to have a detailed knowledge of the genetic and molecular bases regulating plant resistance to these pathogens. Arabidopsis thaliana resistance to necrotrophic pathogens, such as Plectosphaerella cucumerina BMM (PcBMM) fungus, is genetically complex and depends on the coordinated activation of various signaling pathways. These include those regulated by salicylic acid (SA), jasmonic acid (JA), ethylene (ET) and abscisic acid (ABA) hormones and the synthesis of tryptophan-derived antimicrobial compounds and cell wall integrity (Llorente et al., 2005, Hernández-Blanco et al., 2007; Delgado-Cerezo et al., 2012). One key component in the regulation of plant resistance to pathogens (including biotrophic and necrotrophic fungi) is the heterotrimeric G-protein. This protein complex is formed by three subunits (Gα, Gβ and Gγ), which also regulates various plant developmental processes. In Arabidopsis only one gene encodes for subunits α (GPA1) and β (AGB1), and three genes for subunit γ (AGG1, AGG2 y AGG3). The complex GPA1- AGB1-AGG(1-3) is activated and dissociates after perception of an specific signal, AGB1- AGG1/2 acts as a functional monomer regulating defense responses (Delgado-Cerezo et al., 2012). Comparative transcriptomic studies and biochemical analyses of the cell wall of agb1-2 and agg1agg2 mutant and wild plants (Col-0), showed that Gβ-Gγ1/2-mediated resistance is not dependent on previously characterized defense pathways. In addition, it suggests that G protein may modulate the composition/structure (integrity) of the plant cell wall (Delgado-Cerezo et al., 2012). Recently, it has been shown that AGB1 is a critical component of the immune response mediated by Pathogen-Associated Molecular Patterns (PTI), as agb1-2 mutants are unable to activate immune responses such as oxygen reactive species (ROS) production after PAMPs treatment (Liu et al., 2013). Considering the importance of the heterotrimeric G protein in regulation of defense responses (including PTI), we performed a screening for suppressors of agb1-2 susceptibility to the necrotrophic fungus PcBMM. This would allow the identification of additional components of the signaling pathways regulated by AGB1. In this search four sgb mutants (suppressors of agb1-2 susceptibility to pathogens) were isolated, two of which, sgb10 and sgb11, have been characterized in this PhD thesis. sgb10 mutant is a second null allele of MKP1 gene (At3g55270), which encodes the MAP kinase-phosphatase 1 (Bartels et al., 2009). This mutant exhibits spontaneous lesions in adult plants and a constitutive activation of the main defense pathways (SA, JA and ET, and secondary metabolites, such as camalexin), which explains its high resistance to Pseudomonas syringae and PcBMM. Epistatic studies suggest that SGB10- mediated resistance is not dependent, but complementary to the regulated by AGB1. The sgb10 mutant is able to restore agb1-2 ROS production and other PTI responses (MAPK6/3/4/11 phosphorylation) upon treatment with PAMPs as diverse as, flg22, elf18 and chitin, demonstrating the relevant role of SGB10/MKP1 and AGB1 in PTI. sgb11 mutant is characterized by showing a similar phenotype to irregular xylem mutants (e.g. irx1), affected in secondary cell wall: irregular xylems cells, rosette size reduction and plant height, and higher chlorophyll content on leaves. The resistance of sgb11 to PcBMM is independent of agb1-2, as susceptibility of the double mutant agb1-2sgb11 is intermediate between agb1-2 and sgb11. The sgb11 mutant does not revert the deficient PTI response in agb1-2 after flg22 treatment, indicating that is altered in a pathway different to the one regulated by SGB10. sgb11 presents an over-activation of the abscisic acid pathway (ABA), which could explain its resistance to PcBMM. The sgb11 mutation has been mapped on chromosome III of Arabidopsis, between AthFUS6 (81.64 cM) and nga6 (86.41 cM) markers, in 200 kb interval, which does not include previously known IRX genes. The isolation and characterization of SGB11 supports the importance of heterotrimeric G protein in the regulation of the interconnection between the cell wall integrity and immunity.

Diseño y síntesis de materiales nanoestructurados basados en aluminatos de estroncio con propiedades fotoluminiscentes

Durante la última década, se han llevado acabo numeroso estudios sobre la síntesis de materiales fotoluminiscentes sub-micrónicos, en gran medida, al amplio número de aplicaciones que demandan este tipo de materiales. En concreto dentro de los materiales fosforescentes o también denominados materiales con una prolongada persistencia de la luminiscencia, los estudios se han enfocado en la matriz de SrAl2O4 dopada con Europio (Eu2+) y Disprosio (Dy3+) dado que tiene mayor estabilidad y persistencia de la fosforescencia con respecto a otras matrices. Estos materiales se emplean mayoritariamente en pinturas luminiscentes, tintas, señalización de seguridad pública, cerámicas, relojes, textiles y juguetes fosforescentes. Dado al amplio campo de aplicación de los SrAl2O4:Eu, Dy, se han investigado múltiples rutas de síntesis como la ruta sol-gel, la síntesis hidrotermal, la síntesis por combustión, la síntesis láser y la síntesis en estado sólido con el fin de desarrollar un método eficiente y que sea fácilmente escalable. Sin embargo, en la actualidad el método que se emplea para el procesamiento a nivel industrial de los materiales basados en aluminato de estroncio es la síntesis por estado sólido, que requiere de temperaturas de entre 1300 a 1900oC y largos tiempos de procesamiento. Además el material obtenido tiene un tamaño de partícula de 20 a 100 μm; siendo este tamaño restrictivo para el empleo de este tipo de material en determinadas aplicaciones. Por tanto, el objetivo de este trabajo es el desarrollo de nuevas estrategias que solventen las actuales limitaciones. Dentro de este marco se plantean una serie de objetivos específicos: Estudio de los parámetros que gobiernan los procesos de reducción del tamaño de partícula mediante molienda y su relación en la respuesta fotoluminiscente. Estudio de la síntesis por combustión de SrAl2O4:Eu, Dy, evaluando el efecto de la temperatura y la cantidad de combustible (urea) en el proceso para la obtención de partículas cristalinas minimizando la presencia de fases secundarias. Desarrollo de nuevas rutas de síntesis de SrAl2O4:Eu, Dy empleando el método de sales fundidas. Determinación de los mecanismos de reacción en presencia de la sal fundida en función de los parámetros de proceso que comprende la relación de sales y reactivos, la naturaleza de la alúmina y su tamaño, la temperatura y atmósfera de tratamiento. Mejora de la eficiencia de los procesos de síntesis para obtener productos con propiedades finales óptimas en procesos factibles industrialmente para su transferencia tecnológica. Es este trabajo han sido evaluados los efectos de diferentes procesos de molienda para la reducción del tamaño de partícula del material de SrAl2O4:Eu, Dy comercial. En el proceso de molienda en medio húmedo por atrición se observa la alteración de la estructura cristalina del material debido a la reacción de hidrólisis generada incluso empleando como medio líquido etanol absoluto. Con el fin de solventar las desventajas de la molienda en medio húmedo se llevo a cabo un estudio de la molturación en seco del material. La molturación en seco de alta energía reduce significativamente el tamaño medio de partícula. Sin embargo, procesos de molienda superiores a una duración de 10 minutos ocasionan un aumento del estado de aglomeración de las partículas y disminuyen drásticamente la respuesta fotoluminiscente del material. Por tanto, se lleva a cabo un proceso de molienda en seco de baja energía. Mediante este método se consigue reducir el tamaño medio de partícula, d50=2.8 μm, y se mejora la homogeneidad de la distribución del tamaño de partícula evitando la amorfización del material. A partir de los resultados obtenidos mediante difracción de rayos X y microscopia electrónica de barrido se infiere que la disminución de la intensidad de la fotoluminiscencia después de la molienda en seco de alta energía con respecto al material inicial se debe principalmente a la reducción del tamaño de cristalito. Se observan menores variaciones en la intensidad de la fotoluminiscencia cuando se emplea un método de molienda de baja de energía ya que en estos procesos se preserva el dominio cristalino y se reduce la amorfización significativamente. Estos resultados corroboran que la intensidad de la fotoluminiscencia y la persistencia de la luminiscencia de los materiales de SrAl2O4:Eu2+, Dy3+ dependen extrínsecamente de la morfología de las partículas, del tamaño de partícula, el tamaño de grano, los defectos superficiales e intrínsecamente del tamaño de cristalito. Siendo las características intrínsecas las que dominan con respecto a las extrínsecas y por tanto tienen mayor relevancia en la respuesta fotoluminiscente. Mediante síntesis por combustión se obtuvieron láminas nanoestructuradas de SrAl2O4:Eu, Dy de ≤1 μm de espesor. La cantidad de combustible, urea, en la reacción influye significativamente en la formación de determinadas fases cristalinas. Para la síntesis del material de SrAl2O4:Eu, Dy es necesario incluir un contenido de urea mayor que el estequiométrico (siendo m=1 la relación estequiométrica). La incorporación de un exceso de urea (m>1) requiere de la presencia de un agente oxidante interno, HNO3, para que la reacción tenga lugar. El empleo de un mayor contenido de urea como combustible permite una quelación efectiva de los cationes en el sistema y la creación de las condiciones reductoras para obtener un material de mayor cristalinidad y con mejores propiedades fotoluminiscentes. El material de SrAl2O4:Eu, Dy sintetizado a una temperatura de ignición de 600oC tiene un tamaño medio 5-25 μm con un espesor de ≤1 μm. Mediante procesos de molturación en seco de baja energía es posible disminuir el tamaño medio de partícula ≈2 μm y homogenizar la distribución del tamaño de partícula pero hay un deterioro asociado de la respuesta luminiscente. Sin embargo, se puede mejorar la respuesta fotoluminiscente empleando un tratamiento térmico posterior a 900oC N2-H2 durante 1 hora que no supone un aumento del tamaño de partícula pero si permite aumentar el tamaño de cristalito y la reducción del Eu3+ a Eu2+. Con respecto a la respuesta fotoluminiscente, se obtiene valores de la intensidad de la fotoluminiscencia entre un 35%-21% con respecto a la intensidad de un material comercial de referencia. Además la intensidad inicial del decaimiento de la fosforescencia es un 20% de la intensidad del material de referencia. Por tanto, teniendo en cuenta estos resultados, es necesario explorar otros métodos de síntesis para la obtención de los materiales bajo estudio. Por esta razón, en este trabajo se desarrollo una ruta de síntesis novedosa para sintetizar SrAl2O4:Eu, Dy mediante el método de sales fundidas para la obtención de materiales de gran cristalinidad con tamaños de cristalito del orden nanométrico. Se empleo como sal fundente la mezcla eutéctica de NaCl y KCl, denominada (NaCl-KCl)e. La principal ventaja de la incorporación de la mezcla es el incremento la reactividad del sistema, reduciendo la temperatura de formación del SrAl2O4 y la duración del tratamiento térmico en comparación con la síntesis en estado sólido. La formación del SrAl2O4 es favorecida ya que se aumenta la difusión de los cationes de Sr2+ en el medio líquido. Se emplearon diferentes tipos de Al2O3 para evaluar el papel del tamaño de partícula y su naturaleza en la reacción asistida por sales fundidas y por tanto en la morfología y propiedades del producto final. Se obtuvieron partículas de morfología pseudo-esférica de tamaño ≤0.5 μm al emplear como alúmina precursora partículas sub-micrónicas ( 0.5 μm Al2O3, 0.1 μm Al2 O3 y γ-Al2O3). El mecanismo de reacción que tiene lugar se asocia a procesos de disolución-precipitación que dominan al emplear partículas de alúmina pequeñas y reactivas. Mientras al emplear una alúmina de 6 μm Al2O3 prevalecen los procesos de crecimiento cristalino siguiendo un patrón o plantilla debido a la menor reactividad del sistema. La nucleación y crecimiento de nanocristales de SrAl2O4:Eu, Dy se genera sobre la superficie de la alúmina que actúa como soporte. De esta forma se desarrolla una estructura del tipo coraza-núcleo («core-shell» en inglés) donde la superficie externa está formada por los cristales fosforescentes de SrAl2O4 y el núcleo está formado por alúmina. Las partículas obtenidas tienen una respuesta fotoluminiscente diferente en función de la morfología final obtenida. La optimización de la relación Al2O3/SrO del material de SrAl2O4:Eu, Dy sintetizado a partir de la alúmina de 6 μm permite reducir las fases secundarias y la concentración de dopantes manteniendo la respuesta fotoluminiscente. Comparativamente con un material comercial de SrAl2O4:Eu, Dy de referencia, se han alcanzado valores de la intensidad de la emisión de hasta el 90% y de la intensidad inicial de las curvas de decaimiento de la luminiscencia de un 60% para el material sintetizado por sales fundidas que tiene un tamaño medio ≤ 10μm. Por otra parte, es necesario tener en cuenta que el SrAl2O4 tiene dos polimorfos, la fase monoclínica que es estable a temperaturas inferiores a 650oC y la fase hexagonal, fase de alta temperatura, estable a temperaturas superiores de 650oC. Se ha determinado que fase monoclínica presenta propiedades luminiscentes, sin embargo existen discordancias a cerca de las propiedades luminiscentes de la fase hexagonal. Mediante la síntesis por sales fundidas es posible estabilizar la fase hexagonal empleando como alúmina precursora γ-Al2O3 y un exceso de Al2O3 (Al2O3/SrO:2). La estabilización de la fase hexagonal a temperatura ambiente se produce cuando el tamaño de los cristales de SrAl2O4 es ≤20 nm. Además se observó que la fase hexagonal presenta respuesta fotoluminiscente. El diseño de materiales de SrAl2O4:Eu,Dy nanoestructurados permite modular la morfología del material y por tanto la intensidad de la de la fotoluminiscencia y la persistencia de la luminiscencia. La disminución de los materiales precursores, la temperatura y el tiempo de tratamiento significa la reducción de los costes económicos del material. De ahí la viabilidad de los materiales de SrAl2O4:Eu,Dy obtenidos mediante los procesos de síntesis propuestos en esta memoria de tesis para su posterior escalado industrial. ABSTRACT The synthesis of sub-micron photoluminescent particles has been widely studied during the past decade because of the promising industrial applications of these materials. A large number of matrices has been developed, being SrAl2O4 host doped with europium (Eu2+) and dysprosium (Dy3+) the most extensively studied, because of its better stability and long-lasting luminescence. These functional inorganic materials have a wide field of application in persistent luminous paints, inks and ceramics. Large attention has been paid to the development of an efficient method of preparation of SrAl2O4 powders, including solgel method, hydrothermal synthesis, laser synthesis, combustion synthesis and solid state reaction. Many of these techniques are not compatible with large-scale production and with the principles of sustainability. Moreover, industrial processing of highly crystalline powders usually requires high synthesis temperatures, typically between 1300 a 1900oC, with long processing times, especially for solid state reaction. As a result, the average particle size is typically within the 20-100 μm range. This large particle size is limiting for current applications that demand sub-micron particles. Therefore, the objective of this work is to develop new approaches to overcome these limitations. Within this frame, it is necessary to undertake the following purposes: To study the parameters that govern the particle size reduction by milling and their relation with the photoluminescence properties. To obtain SrAl2O4:Eu, Dy by combustion synthesis, assessing the effect of the temperature and the amount of fuel (urea) to synthesize highly crystalline particles minimizing the presence of secondary phases. To develop new synthesis methods to obtain SrAl2O4:Eu, Dy powders. The molten salt synthesis has been proposed. As the method is a novel route, the reaction mechanism should be determine as a function of the salt mixture, the ratio of the salt, the kind of Al2O3 and their particle size and the temperature and the atmosphere of the thermal treatment. To improve the efficiency of the synthesis process to obtain SrAl2O4:Eu, Dy powders with optimal final properties and easily scalable. On the basis of decreasing the particle size by using commercial product SrAl2O4:Eu2+, Dy3+ as raw material, the effects of different milling methods have been evaluated. Wet milling can significantly alter the structure of the material through hydrolysis reaction even in ethanol media. For overcoming the drawbacks of wet milling, a dry milling-based processes are studied. High energy dry milling process allows a great reduction of the particle size, however milling times above 10 min produce agglomeration and accelerates the decrease of the photoluminescence feature. To solve these issues the low energy dry milling process proposed effectively reduces the particle size to d50=2.8 μm, and improves the homogeneity avoiding the amorphization in comparison with previous methods. The X-ray diffraction and scanning electron microscope characterization allow to infer that the large variations in PL (Photoluminescence) values by high energy milling process are a consequence mainly of the crystallite size reduction. The lesser variation in PL values by low energy milling proces is related to the coherent crystalline domain preservation and the unnoticeable amorphization. These results corroborate that the photoluminescence intensity and the persistent luminescence of the SrAl2O4:Eu2+, Dy3+ powders depend extrinsically on the morphology of the particles such as particle size, grain size, surface damage and intrinsically on the crystallinity (crystallite size); being the intrinsically effects the ones that have a significant influence on the photoluminescent response. By combustion method, nanostructured SrAl2O4:Eu2+, Dy3+ sheets with a thickness ≤1 μm have been obtained. The amount of fuel (urea) in the reaction has an important influence on the phase composition; urea contents larger than the stoichiometric one require the presence of an oxidant agent such as HNO3 to complete the reaction. A higher amount of urea (excess of urea: denoted m>1, being m=1 the stoichiometric composition) including an oxidizing agent produces SrAl2O4:Eu2+,Dy3+ particles with persistent luminescence due to the effective chelation of the cations and the creation of suitable atmospheric conditions to reduce the Eu3+ to Eu2+. Therefore, optimizing the synthesis parameters in combustion synthesis by using a higher amount of urea and an internal oxidizing agent allows to complete the reaction. The amount of secondary phases can be significantly reduced and the photoluminescence response can be enhanced. This situation is attributed to a higher energy that improves the crystallinity of the powders. The powders obtained have a particle size c.a. 5-25 μm with a thickness ≤1 μm and require relatively low ignition temperatures (600oC). It is possible to reduce the particle size by a low energy dry milling but this process implies the decrease of the photoluminescent response. However, a post-thermal treatment in a reducing atmosphere allows the improvement of the properties due to the increment of crystallinity and the reduction of Eu3+ to Eu2+. Compared with the powder resulted from solid state method (commercial reference: average particle size, 20 μm and heterogeneous particle size distribution) the emission intensity of the powder prepared by combustion method achieve the values between 35% to 21% of the reference powder intensity. Moreover, the initial intensity of the decay curve is 20% of the intensity of the reference powder. Taking in account these results, it is necessary to explore other methods to synthesize the powders For that reason, an original synthetic route has been developed in this study: the molten salt assisted process to obtain highly crystalline SrAl2O4 powders with nanometric sized crystallites. The molten salt was composed of a mixture of NaCl and KCl using a 0.5:0.5 molar ratio (eutectic mixture hereafter abbreviated as (NaCl-KCl)e). The main advantages of salt addition is the increase of the reaction rate, the significant reduction of the synthesis temperature and the duration of the thermal treatment in comparison with classic solid state method. The SrAl2O4 formation is promoted due to the high mobility of the Sr2+ cations in the liquid medium. Different kinds of Al2O3 have been employed to evaluate the role of the size and the nature of this precursor on the kinetics of reaction, on the morphology and the final properties of the product. The SrAl2O4:Eu2+, Dy3+ powders have pseudo-spherical morphology and particle size ≤0.5 μm when a sub-micron Al2O3 ( 0.5 μm Al2O3, 0.1 μm Al2O3 and γ-Al2O3) has been used. This can be attributed to a higher reactivity in the system and the dominance of dissolution-precipitation mechanism. However, the use of larger alumina (6 μm Al2O3) modifies the reaction pathway leading to a different reaction evolution. More specifically, the growth of SrAl2O4 sub-micron particles on the surface of hexagonal platelets of 6μm Al2O3 is promoted. The particles retain the shape of the original Al2O3 and this formation process can be attributed to a «core-shell» mechanism. The particles obtained exhibit different photoluminescent response as a function of the final morphology of the powder. Therefore, through this study, it has been elucidated the reaction mechanisms of SrAl2O4 formation assisted by (NaCl-KCl)e that are governed by the diffusion of SrCO3 and the reactivity of the alumina particles. Optimizing the Al2O3/SrO ratio of the SrAl2O4:Eu, Dy powders synthesized with 6 μm Al2O3 as a precursor, the secondary phases and the concentration of dopant needed can be reduced keeping the photoluminescent response of the synthesized powder. Compared with the commercial reference powder, up to 90% of the emission intensity of the reference powder has been achieved for the powder prepared by molten salt method using 6μm Al2O3 as alumina precursor. Concerning the initial intensity of the decay curve, 60% of the initial intensity of the reference powder has been obtained. Additionally, it is necessary to take into account that SrAl2O4 has two polymorphs: monoclinic symmetry that is stable at temperatures below 650oC and hexagonal symmetry that is stable above this temperature. Monoclinic phase shows luminescent properties. However, there is no clear agreement on the emission of the hexagonal structure. By molten salt, it is possible to stabilize the hexagonal phase of SrAl2O4 employing an excess of Al2O3 (Al2O3/SrO: 2) and γ-Al2O3 as a precursor. The existence of nanometric crystalline domains with lower size (≤20 nm) allows the stabilization of the hexagonal phase. Moreover, it has been evidenced that the hexagonal polymorph exhibits photoluminescent response. To sum up, the design of nanostructured SrAl2O4:Eu2+, Dy3+ materials allows to obtain different morphologies and as consequence different photoluminescent responses. The reduction of temperature, duration of the thermal treatment and the precursors materials needed imply the decrease of the economic cost of the material. Therefore, the viability, suitability and scalability of the synthesis strategy developed in this work to process SrAl2O4:Eu2+, Dy3+ are demonstrated.

Proximo–distal specification in the wing disc of Drosophila by the nubbin gene

Mutations in the nubbin (nub) gene have a phenotype consisting of a severe wing size reduction and pattern alterations, such as transformations of distal elements into proximal ones. nub expression is restricted to the wing pouch cells in wing discs since early larval development. These effects are also observed in genetic mosaics where cell proliferation is reduced in all wing blade regions autonomously, and transformation into proximal elements is observed in distal clones. Clones located in the proximal region of the wing blade cause in addition nonautonomous reduction of the whole wing. Cell lineage experiments in a nub mutant background show that clones respect neither the anterior–posterior nor the dorsal–ventral boundary but that the selector genes have been correctly expressed since early larval development. The phenotypes of nub el and nub dpp genetic combinations are synergistic and the overexpression of dpp in clones in nub wings does not result in overproliferation of the surrounding wild-type cells. We discuss the role of nub in the wing’s proximo–distal axis and in the formation of compartment boundaries.

Importance of newly generated neurons in the adult olfactory bulb for odor discrimination

In adult rodents, neurons are continually generated in the subventricular zone of the forebrain, from where they migrate tangentially toward the olfactory bulb, the only known target for these neuronal precursors. Within the main olfactory bulb, they ascend radially into the granule and periglomerular cell layers, where they differentiate mainly into local interneurons. The functional consequences of this permanent generation and integration of new neurons into existing circuits are unknown. To address this question, we used neural cell adhesion molecule-deficient mice that have documented deficits in the migration of olfactory-bulb neuron precursors, leading to about 40% size reduction of this structure. Our anatomical study reveals that this reduction is restricted to the granule cell layer, a structure that contains exclusively γ-aminobutyric acid (GABA)ergic interneurons. Furthermore, mutant mice were subjected to experiments designed to examine the behavioral consequences of such anatomical alteration. We found that the specific reduction in the newly generated interneuron population resulted in an impairment of discrimination between odors. In contrast, both the detection thresholds for odors and short-term olfactory memory were unaltered, demonstrating that a critical number of bulbar granule cells is crucial only for odor discrimination but not for general olfactory functions.

On the initiation of boudinage and folding instabilities in layered elasto-visco-plastic solids - Insights from natural microstructures and numerical simulations

The present understanding of the initiation of boudinage and folding structures is based on viscosity contrasts and stress exponents, considering an intrinsically unstable state of the layer. The criterion of localization is believed to be prescribed by geometry-material interactions, which are often encountered in natural structures. An alternative localization phenomenon has been established for ductile materials, in which instability emerges for critical material parameters and loading rates from homogeneous conditions. In this thesis, conditions are sought under which this type of instability prevails and whether localization in geological materials necessarily requires a trigger by geometric imperfections. The relevance of critical deformation conditions, material parameters and the spatial configuration of instabilities are discussed in a geological context. In order to analyze boudinage geometries, a numerical eigenmode analysis is introduced. This method allows determining natural frequencies and wavelengths of a structure and inducing perturbations on these frequencies. In the subsequent coupled thermo-mechanical simulations, using a grain size evolution and end-member flow laws, localization emerges when material softening through grain size sensitive viscous creep sets in. Pinch-and-swell structures evolve along slip lines through a positive feedback between the matrix response and material bifurcations inside the layer, independent from the mesh-discretization length scale. Since boudinage and folding are considered to express the same general instability, both structures should arise independently of the sign of the loading conditions and for identical material parameters. To this end, the link between material to energy instabilities is approached by means of bifurcation analyses of the field equations and finite element simulations of the coupled system of equations. Boudinage and folding structures develop at the same critical energy threshold, where dissipative work by temperature-sensitive creep overcomes the diffusive capacity of the layer. This finding provides basis for a unified theory for strain localization in layered ductile materials. The numerical simulations are compared to natural pinch-and-swell microstructures, tracing the adaption of grain sizes, textures and creep mechanisms in calcite veins. The switch from dislocation to diffusion creep relates to strain-rate weakening, which is induced by dissipated heat from grain size reduction, and marks the onset of continuous necking. The time-dependent sequence uncovers multiple steady states at different time intervals. Microstructurally and mechanically stable conditions are finally expressed in the pinch-and-swell end members. The major outcome of this study is that boudinage and folding can be described as the same coupled energy-mechanical bifurcation, or as one critical energy attractor. This finding allows the derivation of critical deformation conditions and fundamental material parameters directly from localized structures in the field.

Improvement of compact terminal antenna performance by incorporating open-end slots in ground plane

This letter describes a new idea of increasing operational bandwidth of a compact planar inverted F antenna (PIFA) by introducing open-end slots in the ground plane under the radiating patch. The slots are not in the way of active modules of a wireless transceiver and thus the proposed antenna size reduction method is attractive from the point of view of practical implementation.

Design of a compact ultra-wideband antenna

A simple method for the design of ultra-wideband antennas in planar format is presented. This method is demonstrated for a high-dielectric-constant substrate material, which allows for a considerable antenna size reduction. Simulations are performed using Ansoft's High-Frequency Structure Simulator (HFSS) for antennas assuming Du-Pont951 (epsilon(r) = 7.8) and RT6010LM (epsilon(r) = 10.2) substrates. For the 1-mm-thick DuPont951, the designed antenna with 22 X 28 nun dimensions features a 10-dB return-loss band width front 2.7 GHz to more than 15 GHz. For the 0.64-mm-thick RT6010LM a 20 X 26 nun antenna exhibits a 10-dB return loss bandwidth from 3.1 to 15 GHz. Both antennas feature nearly omnidirectional properties across the whole 10-dB return-loss bandwidth. The validity of the presented UWB antenna design strategy is confirmed by measurements performed on a prototype developed on RT6010LM substrate. (c) 2006 Wiley Periodicals, Inc.

Mechanical disruption of seagrass in the digestive tract of the dugong

The cheek teeth in dugongs are considered to be largely non-functional whereas the oral horny pads are important both in mechanical disruption of the diet and in conveying seagrass through the mouth. Particle size distributions of digesta from 41 dead stranded dugongs were examined to investigate the relationship between degree of food breakdown, gut region and functional surface area of the mouthparts. The in vitro ease of fracture of major dietary seagrass species were compared. The rate of food breakdown through the gut appears to be more closely linked to fibre level of the diet than to size or age of the dugong and its mouthparts. Low fibre seagrass, for example Halophila ovalis, breaks down at a faster rate than high fibre seagrass, for example Zostera capricorni both in dugong guts and in vitro. Several structural characteristics of seagrass, including level and arrangement of fibre, and water content, make it particularly amenable to mechanical breakdown. The soft mouthparts of the dugong are highly modified so that the entire oral cavity functions to crush low fibre seagrasses. Thus, the dugong has developed an efficient method of food ingestion and mastication that is suited to processing large quantities of soft seagrass during short dive times. The potential cost to the dugong in having lost its hard dental surfaces is that it has become restricted to a low fibre diet.

The role of advanced DEM based modelling tools in increasing comminution energy efficiency

Particle breakage is an essential part of mineral processing. The aim is to reduce run of mine mineral ore to an optimal size for liberating target minerals and for subsequent recovery by separation processes such as flotation. This size reduction is typically accomplished in a series of stages in a grinding circuit tailored to the properties of the particular mine ore. Commonly this involves two or more classes of equipment starting with crushers, followed by SAG mills and then sometimes ball mills. Occasionally, high pressure grinding rolls or other novel devices are substituted. Broadly, energy consumption increases and energy efficiency decreases with the fineness of the material produced by each piece of equipment.