A study of thermodynamic characteristics and predictive computer modelling of an air to water heat pump system

A study on heat pump thermodynamic characteristics has been made in the laboratory on a specially designed and instrumented air to water heat pump system. The design, using refrigerant R12, was based on the requirement to produce domestic hot water at a temperature of about 50 °C and was assembled in the laboratory. All the experimental data were fed to a microcomputer and stored on disk automatically from appropriate transducers via amplifier and 16 channel analogue to digital converters. The measurements taken were R12 pressures and temperatures, water and R12 mass flow rates, air speed, fan and compressor input powers, water and air inlet and outlet temperatures, wet and dry bulb temperatures. The time interval between the observations could be varied. The results showed, as expected, that the COP was higher at higher air inlet temperatures and at lower hot water output temperatures. The optimum air speed was found to be at a speed when the fan input power was about 4% of the condenser heat output. It was also found that the hot water can be produced at a temperature higher than the appropriate R12 condensing temperature corresponding to condensing pressure. This was achieved by condenser design to take advantage of discharge superheat and by further heating the water using heat recovery from the compressor. Of the input power to the compressor, typically about 85% was transferred to the refrigerant, 50 % by the compression work and 35% due to the heating of the refrigerant by the cylinder wall, and the remaining 15% (of the input power) was rejected to the cooling medium. The evaporator effectiveness was found to be about 75% and sensitive to the air speed. Using the data collected, a steady state computer model was developed. For given input conditions s air inlet temperature, air speed, the degree of suction superheat , water inlet and outlet temperatures; the model is capable of predicting the refrigerant cycle, compressor efficiency, evaporator effectiveness, condenser water flow rate and system Cop.

The Model of Unreliable Elements (Human Resources) Intellectual Management System on the Basis of Their Psychological and Personal Characteristics

The Article suggests a possible approach to creation of the Intellectual Management System for human resources and personnel (during their professional tasks solving), and that could consider personal characteristics and psychological condition of the human resources as an “unreliable” element. The Article describes some elements of the Intellectual Management System: professional activity model and “unreliable” element (human resources) model.

Sediment and ice characteristics at a buried ice-wedge system at Barrow

Barrow, the northernmost point in Alaska, is one of the most intensively studied areas in the Arctic. However, paleoenvironmental evidence is limited for northern Alaska for the Lateglacial-Holocene transition. For a regional paleoenvironmental reconstruction, we investigated a permafrost ice-wedge tunnel near Barrow, Alaska. The studied site was first excavated in the early 1960s and intercepts a buried ice-wedge system at 3-6 m depth below the surface. A multi-methodological approach was applied to this buried ice-wedge system and the enclosing sediments, which in their combination, give new insight into the Late Quaternary environmental and climate history. Results of geochronological, sedimentological, cryolithological, paleoecological, isotope geochemical and microbiological studies reflect different stages of mid to late Wisconsin (MW to LW), Allerod (AD), Younger Dryas (YD), Preboreal (PB), and Late Holocene paleoenvironmental evolution. The LW age of the site is indicated by AMS dates in the surrounding sediments of 21.7 kyr BP at the lateral contact of the ice-wedge system as well as 39.5 kyr BP below the ice-wedge system. It is only recently that in this region, stable isotope techniques have been employed, i.e. to characterize different types of ground ice. The stable isotope record (oxygen: d18O; hydrogen: dD) of two intersecting ice wedges suggests different phases of the northern Alaskan climate history from AD to PB, with radiocarbon dates from 12.4 to 9.9 kyr BP (ranging from 14.8 to 10.6 kyr cal BP). Stable isotope geochemistry of ice wedges reveals winter temperature variations of the Lateglacial-Holocene transition including a prominent YD cold period, clearly separated from the warmer AD and PB phases. YD is only weakly developed in summer temperature indicators (such as pollen) for the northern Alaska area, and by consequence, the YD cold stadial was here especially related to the winter season. This highlights that the combination of winter and summer indicators comprehensively describes the seasonality of climate-relevant processes in discrete time intervals. The stable isotope record for the Barrow buried ice-wedge system documents for the first time winter climate change at the Lateglacial-Holocene transition continuously and at relatively high (likely centennial) resolution.

Effects of fare collection policy on operating characteristics of a Brisbane busway station

Transit agencies across the world are increasingly shifting their fare collection mechanisms towards fully automated systems like the smart card. One of the objectives in implementing such a system is to reduce the boarding time per passenger and hence reduce the overall dwell time for the buses at the bus stops/bus rapid transit (BRT) stations. TransLink, the transit authority responsible for public transport management in South East Queensland, has introduced ‘GoCard’ technology using the Cubic platform for fare collection on its public transport system. In addition to this, three inner city BRT stations on South East Busway spine are operating as pre-paid platforms during evening peak time. This paper evaluates the effects of these multiple policy measures on operation of study busway station. The comparison between pre and post policy scenarios suggests that though boarding time per passenger has decreased, while the alighting time per passenger has increased slightly. However, there is a substantial reduction in operating efficiency was observed at the station.

The condition, development and suggestions of policy of the highway express freight transportation system in China

The highway express freight transportation (HEFT) is a new transportation organization form separated from the common freight transportation with economic development and incessant adjustment of highway transportation structure in China. At present, the phenomenon of inadaptability still exists in the HEFT system of China, from foundation structure like highways, parking lots and stations to transportation equipments and transportation organizing. In order to develop the HEFT system more rationally and effectively, we should start with the structure of the system, conform the resources existing, and consummate the freight transport system. In due course, relevant policies and measures to supervise, lead and support are necessary and important. This paper analyzes the existing problems of HEFT system in our country, based on its characteristics, development situation and adaptability, and presents the policy and measures of promoting and leading the development of the HEFT system.

Fatal motorcycle crashes in north Queensland : characteristics and potential interventions

Aims: The Rural and Remote Road Safety Study (RRRSS) addresses a recognised need for greater research on road trauma in rural and remote Australia, the costs of which are disproportionately high compared with urban areas. The 5-year multi-phase study with whole-of-government support concluded in June 2008. Drawing on RRRSS data, we analysed fatal motorcycle crashes which occurred over 39 months to provide a description of crash characteristics, contributing factors and people involved. The descriptive analysis and discussion may inform development of tailored motorcycle safety interventions. Methods: RRRSS criteria sought vehicle crashes resulting in death or hospitalisation for 24 hours minimum of at least 1 person aged 16 years or over, in the study area defined roughly as the Queensland area north from Bowen in the east and Boulia in the west (excluding Townsville and Cairns urban areas). Fatal motorcycle crashes were selected from the RRRSS dataset. Analysis considered medical data covering injury types and severity, evidence of alcohol, drugs and prior medical conditions, as well as crash descriptions supplied by police to Queensland Transport on contributing circumstances, vehicle types, environmental conditions and people involved. Crash data were plotted in a geographic information system (MapInfo) for spatial analysis. Results: There were 23 deaths from 22 motorcycle crashes on public roads meeting RRRSS criteria. Of these, half were single vehicle crashes and half involved 2 or more vehicles. In contrast to general patterns for driver/rider age distribution in crashes, riders below 25 years of age were represented proportionally within the population. Riders in their thirties comprised 41% of fatalities, with a further 36% accounted for by riders in their fifties. 18 crashes occurred in the Far North Statistical Division (SD), with 2 crashes in both the Northern and North West SDs. Behavioural factors comprised the vast majority of contributing circumstances cited by police, with adverse environmental conditions noted in only 4 cases. Conclusions: Fatal motorcycle crashes were more likely to involve another vehicle and less likely to involve a young rider than non-fatal crashes recorded by the RRRSS. Rider behaviour contributed to the majority of crashes and should be a major focus of research, education and policy development, while other road users’ behaviour and awareness also remains important. With 68% of crashes occurring on major and secondary roads within a 130km radius of Cairns, efforts should focus on this geographic area.

Infrastructure project planning decision making : challenges for decision support system applications

Most infrastructure projects share the same characteristics in term of management aspects and shortcomings. Human factor is believed to be the major drawbacks due to the nature of unstructured problems which can further contribute to management conflicts. This growing complexity in infrastructure projects has shift the paradigm of policy makers to adopt Information Communication Technology (ICT) as a driving force. For this reason, it is vital to fully maximise and utilise the recent technologies to accelerate management process particularly in planning phase. Therefore, a lot of tools have been developed to assist decision making in construction project management. The variety of uncertainties and alternatives in decision making can be entertained by using useful tool such as Decision Support System (DSS). However, the recent trend shows that most DSS in this area only concentrated in model development and left few fundamentals of computing. Thus, most of them were found complicated and less efficient to support decision making within project team members. Due to the current incapability of many software aspects, it is desirable for DSS to provide more simplicity, better collaborative platform, efficient data manipulation and reflection to user needs. By considering these factors, the paper illustrates four challenges for future DSS development i.e. requirement engineering, communication framework, data management and interoperability, and software usability

Influence of axial deformation of structural members on vibration characteristics

The vibration characteristics of structural members are significantly influenced by the axial loads and hence axial deformation of the member. Numerous methods have been developed to quantify the axial loads in individual structural members using their natural frequencies. However, the findings of these methods cannot be applied to individual members in a structural framing system as the natural frequency is a global parameter for the entire framing system. This paper proposes an innovative method which uses the modal flexibility parameter to quantify axial deformations in load bearing elements of structural framing systems. The proposed method is illustrated through examples and results highlight that the method can be used to quantify the axial deformations of Individual elements of structural framing systems.

Fabrication using a rapid prototyping system and in vitro characterization of PEG-PCL-PLA scaffolds for tissue engineering

n the field of tissue engineering new polymers are needed to fabricate scaffolds with specific properties depending on the targeted tissue. This work aimed at designing and developing a 3D scaffold with variable mechanical strength, fully interconnected porous network, controllable hydrophilicity and degradability. For this, a desktop-robot-based melt-extrusion rapid prototyping technique was applied to a novel tri-block co-polymer, namely poly(ethylene glycol)-block-poly(epsi-caprolactone)-block-poly(DL-lactide), PEG-PCL-P(DL)LA. This co-polymer was melted by electrical heating and directly extruded out using computer-controlled rapid prototyping by means of compressed purified air to build porous scaffolds. Various lay-down patterns (0/30/60/90/120/150°, 0/45/90/135°, 0/60/120° and 0/90°) were produced by using appropriate positioning of the robotic control system. Scanning electron microscopy and micro-computed tomography were used to show that 3D scaffold architectures were honeycomb-like with completely interconnected and controlled channel characteristics. Compression tests were performed and the data obtained agreed well with the typical behavior of a porous material undergoing deformation. Preliminary cell response to the as-fabricated scaffolds has been studied with primary human fibroblasts. The results demonstrated the suitability of the process and the cell biocompatibility of the polymer, two important properties among the many required for effective clinical use and efficient tissue-engineering scaffolding.

The impact of managers' characteristics on the use of public relations strategy : an exploratory study in Queensland schools

While previous positive and normative studies have focused on the role public relations should play in organisations and the need for management in all organisations to attend to public relations (Cutlip et al., 2006), there has been little discussion in the public relations literature on why or how managers choose to enact public relations strategies for their organisations. If the discipline of public relations is to cement itself as a management function, then researchers must gain a better understanding of managers themselves given that they are the ones who decide if and how public relations strategies should be employed in the organisation. This study has sought to explore evidence of a relationship between management characteristics and their impact on decisions managers make when choosing which public relations strategies to adopt in response to changes in the organisation’s operating environment. This exploratory research study has been conducted within a specific context of schools in Queensland, Australia. Queensland schools have been facing a number of changes within their operating environment due to changes in Federal funding models in Australia’s education system. This study used an exploratory, qualitative approach to understand the management characteristics demonstrated by managers in schools and how these have impacted on the selection of public relations strategies for responding to their changing and increasingly competitive environment. The unit of analysis for this research study was principals in State (government) schools and in non-government schools. Ten principals were interviewed from four different types of schools in Queensland – the more traditional, elite, private schools (GPS Schools); other Independent Schools; Catholic Schools; and State (or public) schools. These interviews were analysed for quantitative comparisons of the managers’ characteristics across the different schools (in terms of the number of principals in each age bracket, those holding postgraduate qualifications, years of experience etc.); and for qualitative data to provide a greater sense of their understanding of public relations. The 10 schools were selected within a geographic area from Brisbane’s inner city to its outer western suburbs to include an element of competition amongst those managers being interviewed. A detailed review of government, school and other public documents was also conducted to gain an insight into the environment in which principals made decisions about public relations strategy to respond to increasing competition. This study found support for the literature on the relationship between management characteristics and strategy. However, there was also variation in findings warranting further investigation of the literature on the relationship between management characteristics and strategy in a school setting. Key relationships found in this study were between: management characteristics themselves; age and the use of public relations strategies; and gender and the use of public relations strategies. There was also evidence of support for the literature linking the impact that the combination of managers’ age, education and experience had on the use of public relations strategies. While this study was exploratory in nature, it did reveal a number of areas that require further investigation to gain a deeper understanding of how and why managers choose public relations strategies as a response to changes in their operating environment. It also provided a different framework to gain a better understanding of managers’ understanding and support of public relations in schools, which, in conjunction with an analysis of their management characteristics, will hopefully allow public relations scholars and practitioners alike gain an understanding of how and why managers use public relations strategies.

Measuring falls events in acute hospitals-A comparison of three reporting methods to identify missing data in the hospital reporting system

OBJECTIVES: To compare three different methods of falls reporting and examine the characteristics of the data missing from the hospital incident reporting system. DESIGN: Fourteen-month prospective observational study nested within a randomized controlled trial. SETTING: Rehabilitation, stroke, medical, surgical, and orthopedic wards in Perth and Brisbane, Australia. PARTICIPANTS: Fallers (n5153) who were part of a larger trial (1,206 participants, mean age 75.1 � 11.0). MEASUREMENTS: Three falls events reporting measures: participants’ self-report of fall events, fall events reported in participants’ case notes, and falls events reported through the hospital reporting systems. RESULTS: The three reporting systems identified 245 falls events in total. Participants’ case notes captured 226 (92.2%) falls events, hospital incident reporting systems captured 185 (75.5%) falls events, and participant selfreport captured 147 (60.2%) falls events. Falls events were significantly less likely to be recorded in hospital reporting systems when a participant sustained a subsequent fall, (P5.01) or when the fall occurred in the morning shift (P5.01) or afternoon shift (P5.01). CONCLUSION: Falls data missing from hospital incident report systems are not missing completely at random and therefore will introduce bias in some analyses if the factor investigated is related to whether the data ismissing.Multimodal approaches to collecting falls data are preferable to relying on a single source alone.

The effects of content presentation format and user characteristics on novice developers’ understanding of process models

Process models are used by information professionals to convey semantics about the business operations in a real world domain intended to be supported by an information system. The understandability of these models is vital to them being used for information systems development. In this paper, we examine two factors that we predict will influence the understanding of a business process that novice developers obtain from a corresponding process model: the content presentation form chosen to articulate the business domain, and the user characteristics of the novice developers working with the model. Our experimental study provides evidence that novice developers obtain similar levels of understanding when confronted with an unfamiliar or a familiar process model. However, previous modeling experience, the use of English as a second language, and previous work experience in BPM are important influencing factors of model understanding. Our findings suggest that education and research in process modeling should increase the focus on human factors and how they relate to content and content presentation formats for different modeling tasks. We discuss implications for practice and research.

Vibration characteristics of plate elements subjected in-plane loads (axial loads)

Axial deformations resulting from in-plane loads (axial forces) of plate elements impact significantly on their vibration characteristics. Although, numerous methods have been developed to quantify axial forces and hence deformations of individual plate elements with different boundary conditions based on their natural frequencies, these methods are unable to apply to the plate elements in a structural system. This is because the natural frequency is a global parameter for the entire structure. Thus, this paper proposes a comprehensive vibration based procedure to quantify axial deformations of plate elements in a structural framing system. Unique capabilities of the proposed method present through illustrative examples. Keywords- Plate Elements, Dynamic Stiffness Matrix, Finite Element Method, Vibration Characteristics, Axial Deformation

Designing a workflow system using coloured petri nets

Traditional workflow systems focus on providing support for the control-flow perspective of a business process, with other aspects such as data management and work distribution receiving markedly less attention. A guide to desirable workflow characteristics is provided by the well-known workflow patterns which are derived from a comprehensive survey of contemporary tools and modelling formalisms. In this paper we describe the approach taken to designing the newYAWL workflow system, an offering that aims to provide comprehensive support for the control-flow, data and resource perspectives based on the workflow patterns. The semantics of the newYAWL workflow language are based on Coloured Petri Nets thus facilitating the direct enactment and analysis of processes described in terms of newYAWL language constructs. As part of this discussion, we explain how the operational semantics for each of the language elements are embodied in the newYAWL system and indicate the facilities required to support them in an operational environment. We also review the experiences associated with developing a complete operational design for an offering of this scale using formal techniques.