Adaptive Pulse Width Control and Sampling for Low Power Pulse Oximetry

Remote sensing of physiological parameters could be a cost effective approach to improving health care, and low-power sensors are essential for remote sensing because these sensors are often energy constrained. This paper presents a power optimized photoplethysmographic sensor interface to sense arterial oxygen saturation, a technique to dynamically trade off SNR for power during sensor operation, and a simple algorithm to choose when to acquire samples in photoplethysmography. A prototype of the proposed pulse oximeter built using commercial-off-the-shelf (COTS) components is tested on 10 adults. The dynamic adaptation techniques described reduce power consumption considerably compared to our reference implementation, and our approach is competitive to state-of-the-art implementations. The techniques presented in this paper may be applied to low-power sensor interface designs where acquiring samples is expensive in terms of power as epitomized by pulse oximetry.

Potentzia-bihurgailu matrizialen diseinu-prozesurako eta hutsegite-tolerantziarako soluzio berriak

290 p.

Use of a high-temperature superconducting coil for magnetic energy storage

A high temperature superconducting magnetic energy storage device (SMES) has been realised using a 350 m-long BSCCO tape wound as a pancake coil. The coil is mounted on a cryocooler allowing temperatures down to 17.2 K to be achieved. The temperature dependence of coil electrical resistance R(T) shows a superconducting transition at T 102.5 K. Measurements of the V(I) characteristics were performed at several temperatures between 17.2 K and 101.5 K to obtain the temperature dependence of the critical current (using a 1 νV/cm criterion). Critical currents were found to exceed 100 A for T < 30 K. An electronic DC-DC converter was built in order to control the energy flow in and out of the superconducting coil. The converter consists of a MOS transistor bridge switching at a 80 kHz frequency and controlled with standard Pulse Width Modulation (PWM) techniques. The system was tested using a 30 V squared wave power supply as bridge input voltage. The coil current, the bridge input and output voltages were recorded simultaneously. Using a 10 A setpoint current in the superconducting coil, the whole system (coil + DC-DC converter) can provide a stable output voltage showing uninterruptible power supply (UPS) capabilities over 1 s. © 2006 IOP Publishing Ltd.

Control energy consumption and system performance in vector control of voltage source converters

Power electronics plays an important role in the control and conversion of modern electric power systems. In particular, to integrate various renewable energies using DC transmissions and to provide more flexible power control in AC systems, significant efforts have been made in the modulation and control of power electronics devices. Pulse width modulation (PWM) is a well developed technology in the conversion between AC and DC power sources, especially for the purpose of harmonics reduction and energy optimization. As a fundamental decoupled control method, vector control with PI controllers has been widely used in power systems. However, significant power loss occurs during the operation of these devices, and the loss is often dissipated in the form of heat, leading to significant maintenance effort. Though much work has been done to improve the power electronics design, little has focused so far on the investigation of the controller design to reduce the controller energy consumption (leading to power loss in power electronics) while maintaining acceptable system performance. This paper aims to bridge the gap and investigates their correlations. It is shown a more thoughtful controller design can achieve better balance between energy consumption in power electronics control and system performance, which potentially leads to significant energy saving for integration of renewable power sources.

Performance evaluation of a novel hybrid multipulse rectifier for utility interface of power electronic converters

This paper presents an improved analysis of a novel Programmable Power-factor-corrected-Based Hybrid Multipulse Power Rectifier (PFC-HMPR) for utility interface of power electronic converters. The proposed hybrid multipulse rectifier is composed of an ordinary three-phase six-pulse diode-bridge rectifier (Graetz bridge) with a parallel connection of single-phase switched converters in each three-phase rectifier leg. In this paper, the authors present a complete discussion about the controlled rectifiers' power contribution and also a complete analysis concerning the total harmonic distortion of current that can be achieved when the proposed converter operates as a conventional 12-pulse rectifier. The mathematical analysis presented in this paper corroborate, with detailed equations, the experimental results of two 6-kW prototypes implemented in a laboratory.

Low-cost PWM speed controller for an electric mini-baja type vehicle

This paperwork presents a Pulse Width Modulation (PWM) speed controller for an electric mini-baja-type car. A battery-fed 1-kW three-phase induction motor provides the electric vehicle traction. The open-loop speed control is implemented with an equal voltage/frequency ratio, in order to maintain a constant amount of torque on all velocities. The PWM is implemented by a low-cost 8-bit microcontroller provided with optimized ROM charts for distinct speed value implementations, synchronized transition between different charts and reduced odd harmonics generation. This technique was implemented using a single passenger mini-baja vehicle, and the essays have shown that its application resulted on reduced current consumption, besides eliminating mechanical parts. Copyright © 2007 by ABCM.

Tri-state Space Vector Modulation for Three-phase integrated inverters

The aim of this work is to present a modified Space Vector Modulation (SVM) suitable for Tri-state Three-phase inverters. A standard SVM algorithm and the Tri-state PWM (Pulse Width Modulation) are presented and their concept are mixed into the novel SVM. The proposed SVM is applied to a three-phase tri-state integrated Boost inverter, intended to Photovoltaic Energy Applications. The main features for this novel SVM are validated through simulations and also by experimental tests. The obtained results prove the feasibility of the proposal. © 2011 IEEE.

Micro-inverter for integrated grid-tie PV module using resonant controller

Two-stage isolated converters for photovoltaic (PV) applications commonly employ a high-frequency transformer on the DC-DC side, submitting the DC-AC inverter switches to high voltages and forcing the use of IGBTs instead of low-voltage and low-loss MOSFETs. This paper shows the modeling, control and simulation of a single-phase full-bridge inverter with high-frequency transformer (HFT) that can be used as part of a two-stage converter with transformerless DC-DC side or as a single-stage converter (simple DC-AC inverter) for grid-connected PV applications. The inverter is modeled in order to obtain a small-signal transfer function used to design the PResonant current control regulator. A high-frequency step-up transformer results in reduced voltage switches and better efficiency compared with converters in which the transformer is used on the DC-DC side. Simulations and experimental results with a 200 W prototype are shown. © 2012 IEEE.

Desenvolvimento e implementação de estratégias de controle digital para regulação de tensão e amortecimento de oscilações eletromecânicas em um gerador síncrono de 10kVA

Neste trabalho são apresentados o desenvolvimento e a implementação de estratégias de controle digital para regulação automática de tensão e para o amortecimento de oscilações eletromecânicas em um sistema de potência em escala reduzida de 10kVA, localizado no Laboratório de Controle de Sistemas de Potência (LACSPOT), da Universidade Federal do Pará (UFPA). O projeto dos dois controladores é baseado na técnica de alocação polinomial de polos. Para o projeto do Regulador Automático de Tensão (RAT) foi adotado um modelo simplificado, de primeira ordem, da máquina síncrona, cujos parâmetros foram levantados experimentalmente. Para o controlador amortecedor, por sua vez, também chamado de Estabilizador de Sistemas de Potência (ESP), foi utilizado um modelo discreto, do tipo auto regressivo com entrada exógena (ARX). Este modelo foi estimado por meio de técnicas de identificação paramétrica, considerando para tal, o conjunto motor-gerador interligado a um sistema de maior porte (concessionária de energia elétrica). As leis de controle foram embarcadas em um microcontrolador de alto desempenho e, para a medição dos sinais utilizados nos controladores, foi desenvolvida uma instrumentação eletrônica baseada em amplificadores operacionais para o condicionamento dos sinais dos sensores. O sinal de controle é baseado na técnica de modulação por largura de pulso (PWM) e comanda o valor médio da tensão de um conversor CC-CC, o qual é utilizado como circuito de excitação que energiza o enrolamento de campo do gerador. Além disso, o acionamento elétrico das máquinas que compõem o grupo gerador de 10kVA foi projetado e automatizado somando segurança aos operadores e ao componentes deste sistema de geração. Os resultados experimentais demonstraram o bom desempenho obtido pela estratégia proposta.

Controlador PID utilizando microcontrolador PIC

This monograph proposes the implementation of a low cost PID controller utilizing a PIC microcontroller, and its application in a positioning system previously controlled by a dedicated integrated circuit for a positioning system. Applying the closed-loop PID control, the system instability was reduced, and its response was smoother, eliminating vibrations and mechanical wear compared to its response with the dedicated integrated circuit, which has a very limited control action. The actuator of the system is a DC motor, whose speed is controlled by the Pulse Width Modulation (PWM) technique, using a Full-Bridge circuit, allowing the shift of direction of rotation. The utilized microcontroller was the PIC16F684, which has an enhanced PWM module, with its analog converters used as reference and position feedback. The positioning sensor is a multiturn potentiometer coupled to the motor axis by gears. The possibility of programming the PID coefficients in the microcontroller, as well as the adjustment of the sampling rate, allows the implemented system achieving high level of versatility

Realizzazione e collaudo di un inverter di media tensione per prove su formette

L’introduzione massiccia dell’elettronica di potenza nel campo degli azionamenti elettrici negli ultimi decenni ha sostanzialmente rivoluzionato la tipologia di alimentazione dei motori elettrici. Da un lato ciò ha migliorato la qualità del controllo della velocità, ma dall’altro ha aggravato le sollecitazioni che gli isolanti delle macchine devono sopportare. Si è infatti passati da tecniche di controllo tradizionali, che consistevano nell’alimentare i motori in alternata direttamente con la rete sinusoidale a 50 Hz (o a 60 Hz), ad alimentazioni indirette, cioè realizzate interponendo tra la rete e la macchina un convertitore elettronico (inverter). Tali dispositivi operano una conversione di tipo ac/dc e dc/ac che permette, come nella modulazione Pulse Width Modulation (PWM), di poter variare la frequenza di alimentazione della macchina, generando una sequenza di impulsi di larghezza variabile. Si è quindi passati dalle tradizionali alimentazioni con forme d’onda alternate sinusoidali a forme di tensione impulsive e ad elevata frequenza, cioè caratterizzate da rapidi fronti di salita e di discesa (dell’ordine di qualche kV/µs). La natura impulsiva di queste forme d’onda ha aggravato la sollecitazione elettrica a cui sono sottoposti i materiali impiegati per l’isolamento dei conduttori degli avvolgimenti delle macchine. E’ importante notare che l’utilizzo dei dispositivi elettronici, che ormai si trovano sparsi nelle reti di bassa tensione, assorbono correnti ad elevato contenuto armonico sul lato di prelievo, hanno quindi un effetto distorcente che altera l’andamento sinusoidale della rete stessa. Quindi, senza opportuni filtri, anche tutte le altre utenze connesse nelle vicinanze, dimensionate per alimentazioni sinusoidali di tipo tradizionale, possono risentire di queste distorsioni armoniche. Per tutti questi motivi è sorta la necessità di verificare l’adeguatezza dei tradizionali isolamenti ad essere in grado di sopportare le sollecitazioni che derivano dall’utilizzo di convertitori elettronici. In particolare, per i motori elettrici tale interrogativo è stato posto in seguito al verificarsi di un elevato numero di guasti inaspettati (precoci), probabilmente imputabile alla diversa sollecitazione elettrica applicata ai materiali. In questa tesi ci si è occupati della progettazione di un inverter di media tensione, che verrà impiegato per eseguire prove sugli avvolgimenti di statore di motori (formette), al fine di condurre successivamente uno studio sull’invecchiamento dei materiali che compongono gli isolamenti. Tale inverter è in grado di generare sequenze di impulsi con modulazione PWM. I parametri caratteristici delle sequenze possono essere modificati in modo da studiare i meccanismi di degradazione in funzione della tipologia delle sollecitazioni applicate. Avendo a che fare con provini di natura capacitiva, il cui isolamento può cedere durante la prova, il sistema deve essere intrinsecamente protetto nei confronti di tutte le condizioni anomale e di pericolo. In particolare deve essere in grado di offrire rapide ed efficaci protezioni per proteggere l’impianto stesso e per salvaguardare la sicurezza degli operatori, dato l’elevato livello delle tensioni in gioco. Per questo motivo è stata pensata un’architettura di sistema ad hoc, in grado di fronteggiare le situazioni anomale in modo ridondante. E’ infatti stato previsto l’inserimento di un sistema di controllo basato sul CompactRIO, sul quale è stato implementato un software in grado di monitorare le grandezze caratteristiche del sistema e le protezioni che affiancheranno quelle hardware, realizzate con dispositivi elettronici. I dispositivi elettronici di protezione e di interfacciamento sono stati studiati, implementati e simulati con PSpice, per poi essere successivamente dimensionati e realizzati su schede elettroniche, avvalendosi del software OrCAD. La tesi è strutturata come segue: - Il primo capitolo tratta, in maniera generale, i motori asincroni trifase, gli inverter e l’invecchiamento dei sistemi isolanti, con particolare interesse alle sollecitazioni meccaniche, termiche ed elettriche nel caso di sollecitazioni impulsive; - Il secondo capitolo riguarda il sistema realizzato nel suo complesso. Inizialmente verrà descritto lo schema elettrico generale, per poi analizzare più nello specifico le varie parti di cui il sistema è composto, come l’inverter di media tensione, il generatore di media tensione, la scheda di disaccoppiamento ottico, la scheda di controllo del generatore di media tensione, la scheda OCP; - Il terzo capitolo descrive le lavorazioni meccaniche eseguite sulle scatole contenti i rami di inverter, la realizzazione delle fibre ottiche e riporta le fasi di collaudo dell’intero sistema. Infine, verranno tratte le conclusioni.

Caratterizzazione e generazione di segnali PWM per amplificatori in classe D ad alta efficienza

The convergence of information technology and consumer electronics towards battery powered portable devices has increased the interest in high efficiency, low dissipation amplifiers. Class D amplifiers are the state of the art in low power consumption and high performance amplification. In this thesis we explore the possibility of exploiting nonlinearities introduced by the PWM modulation, by designing an optimized modulation law which scales its carrier frequency adaptively with the input signal's average power while preserving the SNR, thus reducing power consumption. This is achieved by means of a novel analytical model of the PWM output spectrum, which shows how interfering harmonics and their bandwidth affect the spectrum. This allows for frequency scaling with negligible aliasing between the baseband spectrum and its harmonics. We performed low noise power spectrum measurements on PWM modulations generated by comparing variable bandwidth, random test signals with a variable frequency triangular wave carrier. The experimental results show that power-optimized frequency scaling is both feasible and effective. The new analytical model also suggests a new PWM architecture that can be applied to digitally encoded input signals which are predistorted and compared with a cosine carrier, which is accurately synthesized by a digital oscillator. This approach has been simulated in a realistic noisy model and tested in our measurement setup. A zero crossing search on the obtained PWM modulation law proves that this approach yields an equivalent signal quality with respect to traditional PWM schemes, while entailing the use of signals whose bandwidth is remarkably smaller due to the use of a cosine instead of a triangular carrier.

Performance optimization in switched reluctance motor drives

In this paper, switched reluctance motors (SRM) are proposed as an alternative for electric power assisted steering (EPAS) applications. A prototype machine has been developed as very attractive design for a steering electric motor, both from a cost and size perspective. A fourphase 8/6 SRM drive is designed for a rack type EPAS which should provide a maximum force of 10 kN. Two-dimension finite element analysis is used to validate the design.

A conventional myosin motor drives neurite outgrowth

Neuritic outgrowth is a striking example of directed motility, powered through the actions of molecular motors. Members of the myosin superfamily of actin-associated motors have been implicated in this complex process. Although conventional myosin II is known to be present in neurons, where it is localized at the leading edge of growth cones and in the cell cortex close to the plasma membrane, its functional involvement in growth cone motility has remained unproven. Here, we show that antisense oligodeoxyribonucleotides, complementary to a specific isoform of conventional myosin (myosin IIB), attenuate filopodial extension whereas sense and scrambled control oligodeoxyribonucleotides have no effect. Attenuation is shown to be reversible, neurite outgrowth being restored after cessation of the antisense regimen. Myosin IIB mRNA was present during active neurite extension, but levels were minimal in phenotypically rounded cells before neurite outgrowth and message levels decreased during antisense treatment. By contrast, the myosin IIA isoform is shown to be expressed constitutively both before and during neurite outgrowth and throughout exposure to myosin IIB antisense oligodeoxyribonucleotides. These results provide direct evidence that a conventional two-headed myosin is required for growth cone motility and is responsible, at least in part, for driving neuritic process outgrowth.