Briefing: Factored material properties and limit state loads-unlikely extreme or impossible pretense

In the limit state design (LSD) method each design criterion is formally stated and assessed using a performance function. The performance function defines the relationship between the design parameters and the design criterion. In practice, LSD involves factoring up loads and factoring down calculated strengths and material parameters. This provides a convenient way to carry out routine probabilistic-based design. The factors are statistically calculated to produce a design with an acceptably low probability of failure. Hence the ultimate load and the design material properties are mathematical concepts that have no physical interpretation. They may be physically impossible. Similarly, the appropriate analysis model is also defined by the performance function and may not describe the real behaviour at the perceived physical equivalent limit condition. These points must be understood to avoid confusion in the discussion and application of partial factor LSD methods.

Delineation of sulphide ore-zones by borehole radar tomography at Hellyer Mine, Australia

Velocity and absorption tomograms are the two most common forms of presentation of radar tomographic data. However, mining personnel, geophysicists included, are often unfamiliar with radar velocity and absorption. In this paper, general formulae are introduced, relating velocity and attenuation coefficient to conductivity and dielectric constant. The formulae are valid for lossy media as well as high-resistivity materials. The transformation of velocity and absorption to conductivity and dielectric constant is illustrated via application of the formulae to radar tomograms from the Hellyer zinc-lead-silver mine, Tasmania, Australia. The resulting conductivity and dielectric constant tomograms constructed at Hellyer demonstrated the potential of radar tomography to delineate sulphide ore zones. (C) 2001 Elsevier Science B.V. All rights reserved.

Air target detection via bistatic radar based on LEOS communication signals

The paper discusses the bistatic radar parameters for the case when the transmitter is a satellite emitting communication signals. The model utilises signals from an Iridium-like low earth orbiting satellite system. The maximum detection range, when thermal noise-limited, is discussed at the theoretical level and these results are compared with experimentation. Satellite-radar signal levels and the power of ground reflections are evaluated.

Three-dimensional space-borne synthetic aperture radar (SAR) imaging with multiple pass processing

Three-dimensional (3D) synthetic aperture radar (SAR) imaging via multiple-pass processing is an extension of interferometric SAR imaging. It exploits more than two flight passes to achieve a desired resolution in elevation. In this paper, a novel approach is developed to reconstruct a 3D space-borne SAR image with multiple-pass processing. It involves image registration, phase correction and elevational imaging. An image model matching is developed for multiple image registration, an eigenvector method is proposed for the phase correction and the elevational imaging is conducted using a Fourier transform or a super-resolution method for enhancement of elevational resolution. 3D SAR images are obtained by processing simulated data and real data from the first European Remote Sensing satellite (ERS-1) with the proposed approaches.

Resistively loaded helical antennas for ground-penetrating radar

Resistively loaded helical antennas, used in the normal mode and horizontally polarised, are modelled using the moment method above typical lossy ground. The distributed resistive loading was adjusted to maintain a two octave bandwidth. The centre frequency of 1 m dipoles was reduced from 250 MHz for the straight resistive wire to 50 MHz for a helix of pitch 2.5 cm and diameter 5 cm. The reduction in efficiency required to maintain the bandwidth for this helix was 12 dB. This agrees reasonably with the theory for small antennas in free space. The results were also verified by comparing measurements performed on a monopole resistively loaded helical antenna in a watertank with the numerical model used elsewhere.

Beneficial effects of air inclusions on the performance of ethylene vinyl acetate (EVA) mouthguard material

Objective: To investigate the impact characteristics of an ethylene vinyl acetate (EVA) mouthguard material with regulated air inclusions, which included various air cell volumes and wall thickness between air cells. In particular, the aim was to identify the magnitude and direction of forces within the impacts. Method: EVA mouthguard material, A mm thick and with and without air inclusions, was impacted with a constant force impact pendulum with an energy of 4.4 J and a velocity of 3 m/s. Transmitted forces through the EVA material were measured using an accelerometer, which also allowed the determination of force direction and magnitude within the impacts. Results: Statistically significant reductions in the transmitted forces were observed with all the air inclusion materials when compared with EVA without air inclusions. Maximum transmitted force through one air inclusion material was reduced by 32%. Force rebound was eliminated in one material, and reduced second force impulses were observed in all the air inclusion materials. Conclusion: The regulated air inclusions improved the impact characteristics of the EVA mouthguard material, the material most commonly used in mouthguards world wide.

Effect of ethylene vinyl acetate (EVA) closed cell foam on transmitted forces in mouthguard material

Objectives: To compare transmitted forces through ethylene vinyl acetate (EVA) mouthguard material and the same EVA material with gas inclusions in the form of a closed cell foam. Method: EVA mouthguard materials with and without foam gas inclusions and 4 mm thick were impacted with a constant force from an impact pendulum. Various porosity levels in the foam materials were produced by 1%, 5%, and 10% by weight foaming agent. The forces transmitted through the EVA after energy absorption by the test materials were measured with a force sensor and compared. Results: Only minor non-significant differences in transmitted forces through the EVA with and without foam were shown. Conclusions: The inclusion of gas in the form of a closed cell foam in 4 mm thick EVA mouthguard materials did not improve the impact performance of the EVA mouthguard material.

A design method for superconducting MRI magnets with ferromagnetic material

The emphasis of this work is on the optimal design of MRI magnets with both superconducting coils and ferromagnetic rings. The work is directed to the automated design of MRI magnet systems containing superconducting wire and both `cold' and `warm' iron. Details of the optimization procedure are given and the results show combined superconducting and iron material MRI magnets with excellent field characteristics. Strong, homogeneous central magnetic fields are produced with little stray or external field leakage. The field calculations are performed using a semi-analytical method for both current coil and iron material sources. Design examples for symmetric, open and asymmetric clinical MRI magnets containing both superconducting coils and ferromagnetic material are presented.

Rapid field calculations for the effect of ferromagnetic material in MRI magnet design

Magnetic resonance imaging (MRI) magnets have very stringent constraints on the homogeneity of the static magnetic field that they generate over desired imaging regions. The magnet system also preferably generates very little stray field external to its structure, so that ease of siting and safety are assured. This work concentrates on deriving, means of rapidly computing the effect of 'cold' and 'warm' ferromagnetic material in or around the superconducting magnet system, so as to facilitate the automated design of hybrid material MR magnets. A complete scheme for the direct calculation of the spherical harmonics of the magnetic field generated by a circular ring of ferromagnetic material is derived under the conditions of arbitrary external magnetizing fields. The magnetic field produced by the superconducting coils in the system is computed using previously developed methods. The final, hybrid algorithm is fast enough for use in large-scale optimization methods. The resultant fields from a practical example of a 4 T, clinical MRI magnet containing both superconducting coils and magnetic material are presented.

Caixas receptoras de correspond??ncias confeccionadas com material recicl??vel

Os Correios t??m como miss??o facilitar as rela????es pessoais e empresariais mediante a oferta de servi??os de correios com ??tica, competitividade, lucratividade e responsabilidade social. Fundamentada em objetivos estrat??gicos, como o de obter padr??es de qualidade e produtividade requeridos pelas partes interessadas e aumentar a percep????o da sociedade em rela????o ?? atua????o da ECT como empresa socialmente respons??vel, a Ag??ncia de Conchas/DR/SPI implantou a????o socioambiental e educacional com a comunidade: a instala????o de caixas receptoras de correspond??ncia em suas resid??ncias, utilizando materiais recicl??veis. O projeto proporcionou ganhos significativos para a Ag??ncia e para os mun??cipes na presta????o de um servi??o com maior qualidade e agilidade a partir da melhoria gradativa das condi????es de entrega nos novos bairros atendidos pelo servi??o, al??m da satisfa????o e do reconhecimento da sociedade com a a????o de inclus??o social

Sistema radar comercial

O Sistema Radar Comercial ?? uma ferramenta in??dita de intelig??ncia comercial, que permite a identifica????o de oportunidades comerciais no mercado externo, em n??vel de seis d??gitos do Sistema Harmonizado (SH6). As informa????es e an??lises oferecidas pelo Sistema cont??m elementos b??sicos para a formula????o de estrat??gias de promo????o comercial, tanto do governo como da iniciativa privada, para o direcionamento dos fluxos de investimentos voltados para a amplia????o das exporta????es brasileiras e para o balizamento dos interesses do Brasil em negocia????es internacionais. A partir de um c??digo SH, ou de uma palavra chave que identifique determinado produto, o usu??rio do Sistema pode acessar, via internet, uma gama de an??lises sobre o produto desejado, em diferentes mercados. Al??m disso, o sistema possibilita a sele????o dos ???produtos priorit??rios???, para o Brasil ou para cada Estado da Federa????o

Relat??rio final do projeto desenvolvimento de capacidade de lideran??a (Brasil-Canad??)

Desde o in??cio de 2000, a Canada School of Public Service (CSPS) e a Escola Nacional de Administra????o P??blica (ENAP) demonstraram interesse na possibilidade de coopera????o para desenvolver capacidades de gest??o de servidores p??blicos brasileiros. Um acordo assinado em 2003, inicialmente foi planejado para ser uma parceria de tr??s anos entre as duas escolas. No entanto, a parceria continua at?? hoje e agora estamos no final do segundo, e ??ltimo projeto de coopera????o t??cnica financiado pela Canadian International Development Agency (CIDA) entre Brasil e Canad??, denominado ???Desenvolvimento da Capacidade de Governan??a???. Este relat??rio representa o resultado deste segundo projeto, o qual ampliou o esfor??o de capacita????o da primeira parceria, focando agora em funcion??rios p??blicos mais pr??ximos da "linha de frente" da presta????o de servi??os, aumentando assim a efic??cia do governo nessas ??reas. O projeto mostrou ser bem-sucedido, principalmente, porque seguiu de perto os princ??pios do desenvolvimento eficaz e sustent??vel. Considerando a sua miss??o de desenvolver compet??ncias de servidores p??blicos, a ENAP deu prioridade, dentro deste projeto de coopera????o com o Canad??, a atividades que visam refor??ar a capacidade de governan??a do pa??s, trabalhando em conjunto com escolas em cinco regi??es: Norte, Nordeste, Centro-Oeste, Sudeste e Sul, com especial ??nfase nas ??reas mais pobres do pa??s, localizadas nas regi??es Norte e Nordeste. Foram participantes-chave neste projeto: i) seis escolas brasileiras regionais de administra????o p??blica; ii) uma das principais institui????es acad??micas do Canad?? - Queen's University, e iii) o Minist??rio do Desenvolvimento Social e Combate ?? Fome e tr??s Secretarias de Ra??a, Direitos Humanos e Pol??ticas para as Mulheres. Neste projeto, a CSPS compartilhou suas metodologias em educa????o a dist??ncia, lideran??a e gest??o p??blica. Trabalhando com parceiros brasileiros, ela tamb??m transferiu e adaptou curr??culos e conte??dos de seus cursos. A CIDA forneceu $1.845.000,00 por meio da Programa de Interc??mbio de Conhecimentos para a Promo????o da Eq??idade (PIPE) Brasil-Canad??. A ENAP e as EPBs contribu??ram com $993,752 e a CSPS contribuiu com material de curso, conhecimento e apoio t??cnico no valor de $ 1.000.000

Curso de administra????o de material

O material abrange os seguintes t??picos: t??cnicas modernas de administra????o de materiais;estrutura; funcionamento e desenvolvimento do organismo de material da Administra????o P??blica Federal

Mesa-redonda de pesquisa-a????o em gest??o por compet??ncias: material do participante

A Escola Nacional de Administra????o P??blica, ENAP, em parceria com a Canada School of Public Service, CSPS, vem implementando novas metodologias de abordagem de temas importantes para a melhoria da administra????o p??blica. Em 09 de novembro de 2004 foi instalada a primeira Mesa-redonda de Pesquisa-A????o, ferramenta de pesquisa que tem por objetivo reunir profissionais e especialistas para encontrar solu????es para os desafios enfrentados no servi??o p??blico. O resultado dos debates ?? a publica????o de um material que possa ser ??til a servidores e dirigentes no desempenho de tarefas ou na implementa????o de novas ferramentas de trabalho. A ENAP, cumprindo seu papel de auxiliar na difus??o de conhecimentos no setor p??blico federal, pretende realizar novas mesas periodicamente.