Design of MIMO testbed with an FPGA board for fast signal processing

This paper describes the design of a Multiple Input Multiple Output testbed for assessing various MIMO transmission schemes in rich scattering indoor environments. In the undertaken design, a Field Programmable Gate Array (FPGA) board is used for fast processing of Intermediate Frequency signals. At the present stage, the testbed performance is assessed when the channel emulator between transmitter and receiver modules is introduced. Here, the results are presented for the case when a 2x2 Alamouti scheme for space time coding/decoding at transmitter and receiver is used. Various programming details of the FPGA board along with the obtained simulation results are reported

Implementação de uma matriz de neurônios dinamicamente reconfigurável para descrição de topologias de redes neurais artificiais multilayer perceptrons

The Artificial Neural Networks (ANN), which is one of the branches of Artificial Intelligence (AI), are being employed as a solution to many complex problems existing in several areas. To solve these problems, it is essential that its implementation is done in hardware. Among the strategies to be adopted and met during the design phase and implementation of RNAs in hardware, connections between neurons are the ones that need more attention. Recently, are RNAs implemented both in application specific integrated circuits's (Application Specific Integrated Circuits - ASIC) and in integrated circuits configured by the user, like the Field Programmable Gate Array (FPGA), which have the ability to be partially rewritten, at runtime, forming thus a system Partially Reconfigurable (SPR), the use of which provides several advantages, such as flexibility in implementation and cost reduction. It has been noted a considerable increase in the use of FPGAs for implementing ANNs. Given the above, it is proposed to implement an array of reconfigurable neurons for topologies Description of artificial neural network multilayer perceptrons (MLPs) in FPGA, in order to encourage feedback and reuse of neural processors (perceptrons) used in the same area of the circuit. It is further proposed, a communication network capable of performing the reuse of artificial neurons. The architecture of the proposed system will configure various topologies MLPs networks through partial reconfiguration of the FPGA. To allow this flexibility RNAs settings, a set of digital components (datapath), and a controller were developed to execute instructions that define each topology for MLP neural network.

Implementação de uma matriz de neurônios dinamicamente reconfigurável para descrição de topologias de redes neurais artificiais multilayer perceptrons

The Artificial Neural Networks (ANN), which is one of the branches of Artificial Intelligence (AI), are being employed as a solution to many complex problems existing in several areas. To solve these problems, it is essential that its implementation is done in hardware. Among the strategies to be adopted and met during the design phase and implementation of RNAs in hardware, connections between neurons are the ones that need more attention. Recently, are RNAs implemented both in application specific integrated circuits's (Application Specific Integrated Circuits - ASIC) and in integrated circuits configured by the user, like the Field Programmable Gate Array (FPGA), which have the ability to be partially rewritten, at runtime, forming thus a system Partially Reconfigurable (SPR), the use of which provides several advantages, such as flexibility in implementation and cost reduction. It has been noted a considerable increase in the use of FPGAs for implementing ANNs. Given the above, it is proposed to implement an array of reconfigurable neurons for topologies Description of artificial neural network multilayer perceptrons (MLPs) in FPGA, in order to encourage feedback and reuse of neural processors (perceptrons) used in the same area of the circuit. It is further proposed, a communication network capable of performing the reuse of artificial neurons. The architecture of the proposed system will configure various topologies MLPs networks through partial reconfiguration of the FPGA. To allow this flexibility RNAs settings, a set of digital components (datapath), and a controller were developed to execute instructions that define each topology for MLP neural network.

FPGA-based soft-core processors for image processing applications

With security and surveillance, there is an increasing need to process image data efficiently and effectively either at source or in a large data network. Whilst a Field-Programmable Gate Array (FPGA) has been seen as a key technology for enabling this, the design process has been viewed as problematic in terms of the time and effort needed for implementation and verification. The work here proposes a different approach of using optimized FPGA-based soft-core processors which allows the user to exploit the task and data level parallelism to achieve the quality of dedicated FPGA implementations whilst reducing design time. The paper also reports some preliminary
progress on the design flow to program the structure. An implementation for a Histogram of Gradients algorithm is also reported which shows that a performance of 328 fps can be achieved with this design approach, whilst avoiding the long design time, verification and debugging steps associated with conventional FPGA implementations.

Conceção de um tutorial de Iniciação ao co-projeto de Hardware/software

A crescente evolução dos dispositivos contendo circuitos integrados, em especial os FPGAs (Field Programmable Logic Arrays) e atualmente os System on a chip (SoCs) baseados em FPGAs, juntamente com a evolução das ferramentas, tem deixado um espaço entre o lançamento e a produção de materiais didáticos que auxiliem os engenheiros no Co- Projecto de hardware/software a partir dessas tecnologias. Com o intuito de auxiliar na redução desse intervalo temporal, o presente trabalho apresenta o desenvolvimento de documentos (tutoriais) direcionados a duas tecnologias recentes: a ferramenta de desenvolvimento de hardware/software VIVADO; e o SoC Zynq-7000, Z-7010, ambos desenvolvidos pela Xilinx. Os documentos produzidos são baseados num projeto básico totalmente implementado em lógica programável e do mesmo projeto implementado através do processador programável embarcado, para que seja possível avaliar o fluxo de projeto da ferramenta para um projeto totalmente implementado em hardware e o fluxo de projeto para o mesmo projeto implementado numa estrutura de harware/software.

Kestomagneettitahtikoneen emulointi digitaalisella signaaliprosessorilla

Sähkökäytön suunnittelussa säätöä voidaan testata useassa tapauksessa reaaliaikasimulaattorilla todellisen laitteiston sijaan. Monet reaaliaikasimulaatioiden perustana käytetyt algoritmit soveltuvat täysinohjatulle invertterisillalle. Eräissä sovelluksissa halutaan kuitenkin käyttää puoliksiohjattua siltaa. Puoliksiohjattulla sillalla mallin kausaalisuus voi kääntyä, mitä perinteiset reaaliaikasimulaattorit eivät pysty simuloimaan Tässä työssä oli tavoitteena kehittää reaaliaikasimulaattori puoliksiohjatulle kestomagneettitahtikonekäytölle. Emulaattoriin mallinnettiin todellisen käytön kestomagneettitahtikone ja invertterisilta. Simulaattori toteutettiin digitaaliselle signaaliprosessorille (DSP) ja mittauksiin liittyvät oheislaitteet mallinnettiin FPGA-piirille. Emulaattoriin liitettiin erillinen säätäjä, jota käytettiin myös todellisen sähkökäytön säätämiseen. Emulaattorilla ja todellisella käytöllä tehtyjä mittauksia verrattiin ja emuloimalla saadut tulokset vastasivat melko hyvin todellisesta käytöstä mitattuja.

Comparison and Evaluation of Eddy Current Sensors

In the work eddy current sensors are described and evaluated. Theoretical part includes physical basics of the eddy currents, overview of available commercial products and technologies. Industrial sensors operation was assessed based on several working modes. Apart from this, the model was created in Matlab Simulink with Xilinx Blockset and then translated into a Xilinx ISE Design Suite compatible project. The performance of the resulting implementation was compared to the existing implementation in the Xilinx Spartan 3 FPGA board with the custom made sensor. Additionally, an introduction to FPGAs and VHDL is presented.

A practical method for testing high-speed networking hardware architectures

This paper deals with the key issues encountered in testing during the development of high-speed networking hardware systems by documenting a practical method for "real-life like" testing. The proposed method is empowered by modern and commonly available Field Programmable Gate Array (FPGA) technology. Innovative application of standard FPGA blocks in combination with reconfigurability are used as a back-bone of the method. A detailed elaboration of the method is given so as to serve as a general reference. The method is fully characterised and compared to alternatives through a case study proving it to be the most efficient and effective one at a reasonable cost.

A block coprocessor for user data rate improvements to GPRS coding scheme 4

The general packet radio service (GPRS) has been developed to allow packet data to be transported efficiently over an existing circuit-switched radio network, such as GSM. The main application of GPRS are in transporting Internet protocol (IP) datagrams from web servers (for telemetry or for mobile Internet browsers). Four GPRS baseband coding schemes are defined to offer a trade-off in requested data rates versus propagation channel conditions. However, data rates in the order of > 100 kbits/s are only achievable if the simplest coding scheme is used (CS-4) which offers little error detection and correction (EDC) (requiring excellent SNR) and the receiver hardware is capable of full duplex which is not currently available in the consumer market. A simple EDC scheme to improve the GPRS block error rate (BLER) performance is presented, particularly for CS-4, however gains in other coding schemes are seen. For every GPRS radio block that is corrected by the EDC scheme, the block does not need to be retransmitted releasing bandwidth in the channel and improving the user's application data rate. As GPRS requires intensive processing in the baseband, a viable field programmable gate array (FPGA) solution is presented in this paper.

Improving CS-4 user data rate in GPRS enabled devices by using a BLER co-processor

The General Packet Radio Service (GPRS) was developed to allow packet data to be transported efficiently over an existing circuit switched radio network. The main applications for GPRS are in transporting IP datagram’s from the user’s mobile Internet browser to and from the Internet, or in telemetry equipment. A simple Error Detection and Correction (EDC) scheme to improve the GPRS Block Error Rate (BLER) performance is presented, particularly for coding scheme 4 (CS-4), however gains in other coding schemes are seen. For every GPRS radio block that is corrected by the EDC scheme, the block does not need to be retransmitted releasing bandwidth in the channel, improving throughput and the user’s application data rate. As GPRS requires intensive processing in the baseband, a viable hardware solution for a GPRS BLER co-processor is discussed that has been currently implemented in a Field Programmable Gate Array (FPGA) and presented in this paper.

Flow structure and near-field dispersion in arrays of building-like obstacles

Dispersion in the near-field region of localised releases in urban areas is difficult to predict because of the strong influence of individual buildings. Effects include upstream dispersion, trapping of material into building wakes and enhanced concentration fluctuations. As a result, concentration patterns are highly variable in time and mean profiles in the near field are strongly non-Gaussian. These aspects of near-field dispersion are documented by analysing data from direct numerical simulations in arrays of building-like obstacles and are related to the underlying flow structure. The mean flow structure around the buildings is found to exert a strong influence over the dispersion of material in the near field. Diverging streamlines around buildings enhance lateral dispersion. Entrainment of material into building wakes in the very near field gives rise to secondary sources, which then affect the subsequent dispersion pattern. High levels of concentration fluctuations are also found in this very near field; the fluctuation intensity is of order 2 to 5.

A Parallel Hardware Architecture for Scale and Rotation Invariant Feature Detection

This paper proposes a parallel hardware architecture for image feature detection based on the Scale Invariant Feature Transform algorithm and applied to the Simultaneous Localization And Mapping problem. The work also proposes specific hardware optimizations considered fundamental to embed such a robotic control system on-a-chip. The proposed architecture is completely stand-alone; it reads the input data directly from a CMOS image sensor and provides the results via a field-programmable gate array coupled to an embedded processor. The results may either be used directly in an on-chip application or accessed through an Ethernet connection. The system is able to detect features up to 30 frames per second (320 x 240 pixels) and has accuracy similar to a PC-based implementation. The achieved system performance is at least one order of magnitude better than a PC-based solution, a result achieved by investigating the impact of several hardware-orientated optimizations oil performance, area and accuracy.

Sincronização de múltiplas câmaras e controlo de iluminação sobre uma plataforma FPGA

O objetivo deste projeto foi o de realizar a sincronização de pelo menos quatro câmaras individuais, ajustando dinamicamente o frame rate de operação de cada câmara, tendo por base a família de sensores de imagem CMOS NanEye da empresa Awaiba, numa plataforma FPGA com interface USB3. Durante o projeto analisou-se, com a assistência de um supervisor da Awaiba, o sistema core de captura de imagem existente, baseado em VHDL. Foi estudado e compreendido o princípio do ajuste dinâmico do frame rate das câmaras. Tendo sido então desenvolvido o módulo de controlo da câmara, em VHDL, e um algoritmo de ajuste dinâmico do frame rate, sendo este implementado junto com a plataforma de processamento e interface da FPGA. Foi criado um módulo para efetuar a monitorização da frequência de operação de cada câmara, medindo o período de cada linha numa frame, tendo por base um sinal de relógio de valor conhecido. A frequência é ajustada variando o nível de tensão aplicado ao sensor com base no erro entre o período da linha medido e o período pretendido. Para garantir o funcionamento conjunto de múltiplas câmaras em modo síncrono foi implementada uma interface Master-Slave entre estas. Paralelamente ao módulo anteriormente descrito, implementou-se um sistema de controlo automático de iluminação com base na análise de regiões de interesse em cada frame captada por uma câmara NanEye. A intensidade de corrente aplicada às fontes de iluminação acopladas à câmara é controlada dinamicamente com base no nível de saturação dos pixéis analisados em cada frame. Foram desenvolvidas e implementadas variantes do algoritmo de controlo e o seu desempenho foi avaliado em laboratório. Os resultados obtidos na prática evidenciam que a solução implementada cumpre os requisitos de controlo e ajuste da frequência de operação de múltiplas câmaras. Mostrou ser um método de controlo capaz de manter um erro de sincronização médio de 3,77 μs mesmo na presença de variações de temperatura de aproximadamente 50 °C. Foi também demonstrado que o sistema de controlo de iluminação é capaz de proporcionar uma experiência de visualização adequada, alcançando erros menores que 3% e uma velocidade de ajuste máxima inferior a 1 s.

A novel HPF voltage source rectifier for variable speed refrigeration systems

A novel single-phase voltage source rectifier capable to achieve High-Power-Factor (HPF) for variable speed refrigeration system application, is proposed in this paper. The proposed system is composed by a single-phase high-power-factor boost rectifier, with two cells in interleave connection, operating in critical conduction mode, and employing a soft-switching technique, controlled by a Field Programmable Gate Array (FPGA), associated with a conventional three-phase IGBT bridge inverter (VSI - Voltage Source Inverter), controlled by a Digital Signal Processor (DSP). The soft-switching technique for the input stage is based on zero-current-switching (ZCS) cells. The rectifier's features include the reduction in the input current ripple, the reduction in the output voltage ripple, the use of low stress devices, low volume for the EMI input filter, high input power factor (PF), and low total harmonic distortion (THD) in the input current, in compliance with the EEC61000-3-2 standards. The digital controller for the output stage has been developed using a conventional voltage-frequency control (scalar V/f control), and a simplified stator oriented Vector control, in order to verify the feasibility and performance of the proposed digital controls for continuous temperature control applied at a refrigerator prototype.

Um novo sistema de refrigeração com controle de temperatura, compressor aberto, máquina de indução trifásica com velocidade variável e correção ativa do fator de potência do estágio de entrada

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)