神光Ⅱ升级装置终端光学组件的排布设计

设计高功率激光装置靶场终端光学组件(FOA)时考虑的重要因素是鬼像对光学元件的破坏。由于神光Ⅱ升级装置(SG-Ⅱ-U)的输出能量高、靶场空间小、鬼像分布情况复杂,导致了终端光学组件的设计难度很高。用自主研发的鬼像控制设计软件对神光Ⅱ升级装置靶场终端光学组件排布进行设计,给出了进行鬼像控制设计时需考虑的设计因素,并对比研究了两种靶场终端光学组件设计方案的优缺点,最后结合神光Ⅱ升级装置的特点,优化设计出神光Ⅱ升级装置靶场终端光学组件的最终排布方案。

高功率激光装置光束准直系统新型远场监测技术

利用高功率激光装置空间滤波器小孔成像和取样光栅的衍射,设计出一套新型光路远场监测方案,并且在实验平台上进行了实验验证.实验结果表明:相对传统的远场监测方法,该远场监测系统通过侧面离轴光栅取样灵活利用空间,其调整平均误差为空间滤波器小孔直径0.9%,能够满足准直系统远场调整精度(<小孔直径5%)的要求.

Optimization of Pulse Temporal Contrast in Optical Parametric Chirped Pulse Amplification

In optical parametric chirped pulse amplification (OPCPA), the degradation of temporal contrast of the compressed signal pulse mainly results from spectral clipping in the grating stretcher with finite size of the optics, parametric fluorescence (PF) and the spectral variations transferred from temporal fluctuation of the pump pulse. The temporal contrast of the recompressed amplified pulse in the OPCPA system is studied numerically and a number of solutions are considered and optimized to achieve the highest temporal contrast.

A large-area photolithography technique based on surface plasmons leakage modes

An atomic force microscope (AFM) assisted surface plasmons leakage radiation photolithography technique has been numerically demonstrated by using two-dimensional finite-difference time-domain (2D-FDTD) method. With the aid of a metallic AFM tip, particular characteristic of the Kretstchmann configuration to excite surface plasmons (SPs) is utilized to achieve large-area patterns with high spatial resolution and contrast, the photoresist could be exposed with low power laser due to the remarkable local field enhancement at the metal/dielectric interface and the resonant localized SPs modes near the tip. Good tolerance on the film thickness and incident angle has been obtained, which provides a good practicability for experiments. This photolithography technique proposed here can realize large-area, high-resolution, high-contrast, nondestructive, arbitrary-structure fabrication of nanoscale devices. (c) 2007 Elsevier B.V. All rights reserved.

超大功率二维半导体激光列阵并路自适应稳模技术

半导体列阵量子效率高,输出波长范围涵盖570～1600nm,工作寿命可达数百万小时,叠层列阵可提供超高功率激光输出,在工业、医学等很多领域具有非常广阔的应用前景。但列阵在自由运行时,各发光单元发出的光是不相干的,输出质量差,采用1/4Talbot外腔镜耦合技术,列阵实现了空间锁相最高阶超模,然而唯有基超模远场分布是中心单瓣结构,输出接近衍射极限。为得到最小谱宽、最小发散角、最大功率密度输出,必须将外腔镜倾斜β=λ/2d(λ为工作波长,d为列阵周期),这使得仅有基超模光能成像于发光单元内而被允许振荡。应用此

改善高功率激光二极管阵列光束质量的一种新方法

根据波导模理论,推导了高功率激光二极管阵列的远场分布,根据其分布特点,设计了一种离轴外腔.运用这种外腔,在工作电流为17A时,光束的束宽积从自由运转时的1100mm.mrad减小到128mm.mrad,二极管阵列的光束质量提高了8.5倍左右,输出功率约为自由运转时的75%.

国产掺镱双包层光纤的激光特性

采用MCVD方法研发了掺镱双包层光纤，并对其结构特性、荧光特性和激光特性进行了测试和研究。其D形内包层尺寸为400／450μm，数值孔径为0．36，纤芯直径约为16μm，数值孔径约为0．18。荧光谱线的范围为1000-1140nm，1030nm处的峰宽大于50nm。采用大功率激光二极管单端泵浦6m长的双包层光纤，在泵浦人纤功率为61W时，获得了32W的激光输出，斜率效率为64％。该光纤在高功率处未发现饱和现象，通过优化光纤参数与泵浦方式还可以提高转化效率和输出功率。实验表明该光纤可以取代进口光纤用作高功率

氟磷酸盐玻璃的应用研究进展

氟磷酸盐玻璃系统南于其特殊的光学性能和优良的机做与热学性能一直是特种光学玻璃材料领域的一个研究热点。总结了氟磷酸盐玻璃的分类及玻璃组分与其结构的关系，综述了氟磷玻璃在光学器件、高能高功率激光玻璃、光纤激光器、光纤放大器及上转换发光基质材料等领域上的应用，并对其未来的发展进行了展望。

激光尘埃粒子计数器微型光学传感器的研究

研制成功便携式激光尘埃粒子计数器的核心部件——微型光学传感器。该传感器采用直角散射光收集形式。以高功率半导体激光器作为光源，同时采用高性能的PIN型光电二极管作为光电探测器。散射光收集系统为单一大数值孔径的球面反射镜，其对粒子散射光的收集角范围从20°到160°。粒子散射光信号是脉冲信号，其频谱成份主要在高频段，所以在PIN型光电二极管后用一个带通式前置放大器来消除外界的低频噪声．根据米氏散射理论计算了该光学传感器的光散射响应特性，并用聚苯乙烯标准粒子实测了该光学传感器的性能。结果表明，该系统具有高的信噪

Encircled energy measurement for focusing lens based on scanning Hartmann test

The encircled energy of a focusing lens is one of the parameters directly affecting the target efficiency in high-power laser facilities. The direct measurement method of the encircled energy for the focusing lens based on the scanning Hartmann test is proposed in this paper. With the scanning Hartmann test setup, the information in the whole aperture of the focusing lens can be achieved. The encircled energy can be obtained by analyzing the spot diagram on the focal plane of the focusing lens. In experiments, the encircled energy of an aspheric focusing lens is measured using this method. The measurement result is in good agreement with that derived from measurement data by an interferometer and the difference is 7.7%. (C) 2006 Elsevier GmbH. All rights reserved.

Growth of composite sapphire/Ti : sapphire by the hydrothermal method

Composite sapphire/Ti:sapphire crystals for high-power laser application were grown by the hydrothermal method. The results of the X-ray rocking curve analysis indicate high crystalline quality of the surface Al2O3 material. The strong bonding between the overgrown Al2O3 and seed Ti:Al2O3 crystals is indispensable for withstanding high thermal stresses produced by intense optical pumping. The optical loss at the boundary of the composite crystal is considerably low, indicating the lack of scattering centers. (c) 2005 Elsevier B.V. All rights reserved.

铬、钕双掺钆镓石榴石（Cr^4＋，Nd^3＋）：Gd3Ga5O12激光晶体光学性能的研究

用提拉法生长了掺铬、钕的钆镓石榴石(Cr^4+，Nd^3+：GGG)自调Q激光品体。报道了室温下的吸收光谱和荧光光谱特性。分析了Cr离子浓度对光谱性质的影响。比较了Cr^4+：GGG，Nd^3+：GGG和(Cr^4+，Nd^3+)：GGG晶体吸收光谱的关系。测量了(Cr^4+，Nd^3+)：GGG晶体和Nd^3+：GGG晶体的荧光寿命，它们分别是33μs和250μs。实验表明，(Cr^4+，Nd^3+)：GGG晶体是一种非常有潜力的自调Q激光晶体，可以实现大功率激光器的小型化和全固态化。

Investigation of the spectroscopic properties of Yb3+-doped yttrium lanthanum oxide transparent ceramic

Spectroscopic properties of (Y0.9-xLa0.1Ybx)(2)O-3 transparent ceramic were studied. Two main absorption peaks of the specimen are centered at 940 and 970 nm, which are suitable for InGaAs laser diode pumping. The main emission peaks were located at 1032 and 1075 nm with larger emission cross-section and longer fluorescence lifetime than those of Yb:Y2O3. These properties of (Y0.9-xLa0.1Ybx)(2)O-3 transparent ceramic are favorable to achieve high efficiency and high power laser output. (c) 2007 Elsevier B.V. All rights reserved.

Ta2O5／SiO2硬膜双腔滤光片激光损伤特性研究

研究了Ta2O5／SiO2硬膜双腔干涉滤光片带内、带边及带外的吸收和激光损伤特性。实验发现，对于作用激光，带通滤光片的驻波场分布、吸收率和损伤阈值在带内、带边和带外的响应特性对作用激光波长均呈现出明显的选择性。根据实验结果，结合滤光片的驻波场分析，给出了带通滤光片的损伤机理。

用于钕玻璃啁啾脉冲放大系统光谱整形的多层介质膜反射镜

在千焦拍瓦高功率啁啾脉冲放大系统设计中,为了尽量消除增益窄化和增益饱和效应的影响,同时尽可能提高高功率激光输出脉冲信噪比参数,激光脉冲时空和光谱的整形问题备受关注.提出一种光谱整形新方法,利用特定结构的多层介质膜反射镜,可实现对大能量高功率啁啾脉冲钕玻璃放大系统中啁啾脉冲的光谱整形.研究结果表明,只要合理选择多层介质膜系的结构参数,可有效地控制其反射率分布,且在保证反射相位基本不变的条件下其调制度可超过60%.针对钕玻璃1053nm波长设计而成的光谱整形反射镜,反射带宽可达到196nm,色分辨率约为0.1nm,在几十纳米波长范围所对应的相位偏差小于12mrad,相当于λ/524,能够满足"神光Ⅱ"千焦拍瓦改造的技术指标要求.