Energy Efficiency through Thermal Energy Storage : Possibilities for the Swedish Building Stock

The need for heating and cooling in buildings constitutes a considerable part of the total energy use in a country and reducing this need is of outmost importance in order to reach national and international goals for reducing energy use and emissions. One important way of reaching these goals is to increase the proportion of renewable energy used for heating and cooling of buildings. Perhaps the largest obstacle with this is the often occurring mismatch between the availability of renewable energy and the need for heating or cooling, hindering this energy to be used directly. This is one of the problems that can be solved by using thermal energy storage (TES) in order to save the heat or cold from when it is available to when it is needed. This thesis is focusing on the combination of TES techniques and buildings to achieve increased energy efficiency for heating and cooling. Various techniques used for TES as well as the combination of TES in buildings have been investigated and summarized through an extensive literature review. A survey of the Swedish building stock was also performed in order to define building types common in Sweden. Within the scope of this thesis, the survey resulted in the selection of three building types, two single family houses and one office building, out of which the two residential buildings were used in a simulation case study of passive TES with increased thermal mass (both sensible and latent). The second case study presented in the thesis is an evaluation of an existing seasonal borehole storage of solar heat for a residential community. In this case, real measurement data was used in the evaluation and in comparisons with earlier evaluations. The literature reviews showed that using TES opens up potential for reduced energy demand and reduced peak heating and cooling loads as well as possibilities for an increased share of renewable energy to cover the energy demand. By using passive storage through increased thermal mass of a building it is also possible to reduce variations in the indoor temperature and especially reduce excess temperatures during warm periods, which could result in avoiding active cooling in a building that would otherwise need it. The analysis of the combination of TES and building types confirmed that TES has a significant potential for increased energy efficiency in buildings but also highlighted the fact that there is still much research required before some of the technologies can become commercially available. In the simulation case study it was concluded that only a small reduction in heating demand is possible with increased thermal mass, but that the time with indoor temperatures above 24 °C can be reduced by up to 20%. The case study of the borehole storage system showed that although the storage system worked as planned, heat losses in the rest of the system as well as some problems with the system operation resulted in a lower solar fraction than projected. The work presented within this thesis has shown that TES is already used successfully for many building applications (e.g. domestic hot water stores and water tanks for storing solar heat) but that there still is much potential in further use of TES. There are, however, barriers such as a need for more research for some storage technologies as well as storage materials, especially phase change material storage and thermochemical storage.

Projekt Norrliden : Om småstadspressens etnifiering och genderisering av en förort

The Norrliden project. Genderisation and ethnification of a low status residential area in the local press Media often contributes to segregation by constructing low status residential areas as “different” from what is “normal” and “Swedish”. Research into media representations of these residential areas often focuses big city contexts. Furthermore, research tends to be preoccupied with the construction of ethnic differences, paying little attention to the relationship between construction processes of gender and ethnicity. This article is a critical analysis of how the local daily newspapers in a medium sized town, Kalmar, construct stereotypes of immigrants and gendered identities in the low status residential area Norrliden. Two newspapers were studied in search for articles related to the area, published during the year 2005. Despite the newspapers’ claim that they want to contribute to a more nuanced and less stereotyped image of the residential area the consequences of their work seem to be the opposite. The representation sof the area are coded with stereotypes suggesting that the area is unsafe and dangerous and that the people who live there are motivated by affect and emotions rather than by successful socialisation. These representations are also characterised by notions of ethnicity and gender, as well as class. Norrliden is described as an area in need of change and improvement, as an unfinished project dependent upon aid from the outside. A reading of the 2005 media representations of Norrliden exposes an example of “symbolic violence” in that texts and photographs repeatedly degrade the area and its inhabitants.

From Smart Meters To Smart Decisions: Web-Based Support For The Water Efficient Household

Smart water metering technologies for residential buildings offer, in principle, great opportunities for sustainable urban water management. However, much of this potential is as yet unrealized. Despite that several ICT solutions have already been deployed aiming at optimum operations on the water utilities side (e.g. real time control for water networks, dynamic pump scheduling etc.), little work has been done to date on the consumer side. This paper presents a web-based platform targeting primarily the household end user. The platform enables consumers to monitor, on a real-time basis, the water demand of their household, providing feedback not only on the total water consumption and relevant costs but also on the efficiency (or otherwise) of specific indoor and outdoor uses. Targeting the reduction of consumption, the provided feedback is combined with notifications about possible leakages\bursts, and customised suggestions to improve the efficiency of existing household uses. It also enables various comparisons, with past consumption or even with that of similar households, aiming to motivate further the householder to become an active player in the water efficiency challenge. The issue of enhancing the platform’s functionality with energy timeseries is also discussed in view of recent advances in smart metering and the concept of “smart cities”. The paper presents a prototype of this web-based application and critically discusses first testing results and insights. It also presents the way in which the platform communicates with central databases, at the water utility level. It is suggested that such developments are closing the gap between technology availability and usefulness to end users and could help both the uptake of smart metering and awareness raising leading, potentially, to significant reductions of urban water consumption. The work has received funding from the European Union FP7 Programme through the iWIDGET Project, under grant agreement no318272.

Diagnóstico de perdas e aplicação de ferramentas para o controle da qualidade e melhoria do processo de produção de uma etapa constrututiva de edificações habitacionais

O objeto de estudo desta dissertação é a aplicação de ferramentas para o controle da qualidade e melhoria do processo de produção de uma etapa construtiva de edificações residenciais. As ferramentas aplicadas são: i) controle estatístico do processo – CEP, e; ii) dispositivos Poka-Yoke. A etapa construtiva mencionada é a elevação da estrutura de concreto armado. O estudo foi motivado pela necessidade de melhorar o sistema de manufatura de uma empresa construtora de Porto Alegre – RS, com vistas a reduzir o tempo de construção de suas edificações (lead-time de produção). Para tanto, a partir de conceitos teóricos do Sistema Toyota de Produção – STP, analisou-se o processo produtivo atual para a referida etapa construtiva, identificaram-se perdas existentes no processo e foram propostas melhorias. As ferramentas de qualidade CEP e Poka-Yoke enquadram-se dentro dessa perspectiva de melhoria. Através da sua aplicação, pretende-se eliminar algumas das perdas existentes no processo de construção melhorando sua produtividade e a qualidade do produto final. A aplicação do CEP tem como objetivo avaliar a capacidade do fornecedor de concreto de atender às exigências dos consumidores, de acordo com o que é estipulado pelas normas brasileiras de fabricação e aceitação de concreto, sem impor-lhes ônus desnecessário. A avaliação é efetuada através do monitoramento da variabilidade da propriedade que melhor caracteriza a qualidade do concreto, qual seja, a sua resistência à compressão axial. Os dispositivos Poka-Yoke, por sua vez, são aplicados com funções de controle da qualidade e prevenção de defeitos e, como ferramentas auxiliares na melhoria de atividades produtivas.

Todo Brasileiro merece nível A : habitação multifamiliar para o programa minha casa minha vida energeticamente eficiente

This thesis describes the theoretical, methodological and programmatic proposal for a multifamily residential building located in the urban expansion area of Parnamirim/RN, inserted in the program Minha Casa Minha Vida and level of energy efficiency "A", as the RegulamentoTécnico de Qualidade (RTQ-R/INMETRO) for residential buildings. The development project initially consists of procedures as the study of theoretical, architectural programming and cases studies. With the delimitation of a field solution, situated between the reference and the context, proposals are studied to determine the solution and architectural detailing of the proposal. The architectural program was built based on the method of Problem Seeking (Peña and Parshall, 2001) and research has highlighted aspects of reducing the environmental impact and of the program Minha Casa Minha Vida , among others. The design process was characterized by the incorporation of aspects reviewed and programmed, seeking them compatible and have an economically viable building, socio-spatial quality and energy efficient. The results show that it is possible to obtain a building that meets the constraints of the program that provides housing and energy efficiency level A - and many other environmental qualities and constructive, particularly through architectural design

Qualificação de edifícios residenciais verticais em Natal/RN à luz do regulamento técnico da qualidade para o nível de eficiência energética de edificações residenciais (RTQ-R)

The goal of the research was to investigate the energy performance of residential vertical buildings envelope in the hot and humid climate of Natal, capital of Rio Grande do Norte, based in the Technical Regulation of Quality for Energy Efficiency Level in Residential Buildings (RTQ -R), launched in 2010. The study pretends to contribute to the development of design strategies appropriate to the specific local climate and the increasing of energy efficiency level of the envelope. The methodological procedures included the survey in 22 (twenty two) residential buildings, the formulation of representative prototypes based on typological and constructives characters researched and the classification of the level of energy efficiency in the envelopment of these prototypes, using as a tool the prescriptive method of the RTQ-R and the parametric analyzes from assigning different values of the following variables: shape of the pavement type; distribution of housing compartments; orientation of the building; area and shading of openings; thermal transmittance, and solar absorptance of opaque materials of the frontage in order to evaluate the influence of these on the envelopment performance. The main results accomplished with this work includes the qualification of vertical residential buildings in Natal/RN; the verification of the adequacy of these buildings to local climate based from the diagnosis of the thermal energy of the envelopment performance, the identification of variables with more significant influence on the prescriptive methodology of RTQ-R and design solutions more favorable to obtain higher levels energy efficiency by this method. Finally, it was verified, that some of these solutions proved contradictory in relation to the recommendations contained in the theoretical approaches regarding environmental comfort in hot and humid weather, which indicates the need for improvement of the prescriptive method RTQ-R and further research on efficient design solutions

Indicações para o projeto arquitetônico de edifícios multifamiliares: uma análise pósocupação em Natal/RN

Confirming the Brazilian tendency in the field, the multifamily vertical condominium habitats in Natal are defined as buildings with three or more floors which have been an increasingly used solution. In the mentioned project, the connection between the projectarchitects and the user/ buyers are spread out, by which the first people conceive the realestate property as a creation for the market and not the individual client in specific. Such situation along with technical and financial limitations of the project lead to the adoption of standard solutions to be utilized by clients with different profiles. Besides that, there are various legal and urban parameters by the City Director Plan showing elements of great influence in the final solution adopted by the mentioned edifices. Moving to this subject in general, this project is focused on the case study of the Ed. Ville de Montpellier, having as a base of Post Occupancy Evaluation (POE), considered an efficient tool to analyze and keep up with the progress of the construction of the building, including technical approvals, the application of surveys with the local residents and the creation of informal interviews. The data shows that with time some items that initially motivated the acquisition of the realestate property (with a social common area) move to being less valued, and that the residents quickly alter the pre constructed space, thus seeking to alter the property in a more personal and conforming manner. The possibility of a new emphasis for projects on the mentioned space should also be in discussion, the created project calls for the attention of projected conceptual aspects and interdependence within project and construction which permits the indication of some recommendations for the projection of multifamily residential buildings within the studied realm

An investigation of pile diameter influence in the bearing capacity on Dynamic Load Test (DLT)

During the construction of five residential buildings in the city of Taubate, State of São Paulo, it was possible to carry out one comprehensive investigation of the behavior of precast concrete piles in clay shales. This paper describes the results of Dynamic Load Tests (DLT's) executed in three piles with different diameters and with the same embedded length. The tests were monitored using the PDA(R) (Pile Driving Analyzer) and the pile top displacement was measured by pencil and paper procedure. From the curves of RMX versus DMX resulted from CASE(R) method, CAPWAPC(R) analyses were made for signals where the maximum mobilized soil resistance was verified. The results were compared with the predicted bearing capacity using the semi-empirical method of Decourt & Quaresma (1978) and Decourt (1982) based on SPT values and the description of the soil profile. Some comments related to the values of quake and damping used for clay shales in the analyses are also presented.

Developed and studies on technical and economical viability of an environmental efficient urinal

This work introduces an innovative urinal for public convenience, that promotes at the same time water reuse and personal higiene, in a safe and economical way . Furthermore it demonstrates the latest technology and its technical and economical viabillity of utilization in new and already existing buildings facilities. This new model of personal higiene equipment offers as main benefits the improved economy with subsequent decrease in drinkable water consumption, sanitary safety, low cost and easy installation due to its simplicity and to the fact that it can be installed in already existing facilities. The proposal is constituted by a higienic, ecological and smart system for flushing of public urinals. It is a conjugated system of lavatory and urinal that reuses hands higienization water from the lavatory for flushing purpose. The proposed urinal can be operated manually or automatically by means of a presential sensor. The system promotes drinkable water economy by a rational utilization by avoiding the use of waste water from hand washing in place of clean water for flushing. The proposed equipment increases the economy of clean water in a simple and economical way and it can be installed in any type of public lavatory facilitie such as schools, public buildings, hospitals, commercial buildings, bus terminals, airports, stadiums, parking buildings and shopping centers. Additional benefits of the proposed system is the suggestion of hands washing before and after the use of the urinal without contamination risks from focet handling.and render more attractive the installation for a rational use of clean water in commercial and industrial buildings. Pay-back has shown to be very attractive for a number of internal return rates and also very attractive from the point of view of environmental protection.

Avaliação através do desempenho térmico de edificação verticalizada em Belém-PA

A presente dissertação de mestrado estuda o desempenho térmico de materiais de fachada em uma edificação verticalizada na cidade de Belém – PA, Brasil. Este trabalho tem por objetivo contribuir com estudo do desempenho térmico e eficiência de materiais utilizados na envoltória das edificações residenciais verticalizadas, entre os elementos opacos, foram selecionados dois tipos de materiais, bastante utilizados atualmente na construção civil, a pintura e revestimento cerâmico. Também estuda-se a influência da altura da edificação sobre seu desempenho térmico e eficiência energética. O estudo foi desenvolvido com o uso de modelagem em código computacional no programa EnergyPlus que permite avaliar o desempenho térmico da edificação, a influência da altura na eficiência energética da mesma. Compara-se o desempenho térmico dos dois materiais selecionados, verificou-se que o prédio com revestimento cerâmico apresentou a temperatura interna média anual de 0,42 º C acima da temperatura referente ao prédio pintado, portanto com menor desempenho térmico. A influência da altura do pavimento não produziu uma variação significativa na temperatura interna, pois com seu acréscimo, ocorreu pequena diminuição da temperatura interna, com gradiente térmico da ordem de -0,07ºC /m em decorrência da velocidade do vento que é maior quando mais alto é o pavimento. Considera-se também para este estudo a ventilação natural como estratégia passiva para a edificação em estudo, que segundo a análise da Carta Bioclimática de Givoni contribuiria positivamente para a condição de temperatura interna e umidade do ar, e consequentemente do usuário.

Aplicação do regulamento técnico da qualidade do nível de eficiência energética em edificações residenciais

The research shows that increasing the consumption of energy by households is growing rapidly and without adequate planning, due to population growth and therefore an increase in energy consumption. With the current concerns of sustainability and energy efficiency by industry, there is the need to prove to population that there are many ways to incorporate sustainable practices to their daily lives, starting from by their own residence. The quality certification of the energy efficiency level in residential buildings, shows how one can influence and improve housing issues on sustainable actions as rooted in our country

Clima e vulnerabilidade socioespacial: uma avaliação dos fatores de risco na população urbana do município de São Luís (MA)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Willem Marinus Dudok. Progetti urbani per la citta' di Hilversum

Il tema principale affrontato dalla presente ricerca è quello dell’architettura della città; attraverso lo studio dei progetti urbani redatti dall’architetto Willem Marinus Dudok per la città di Hilversum, la tesi vuole confermare l’ipotesi che la costruzione dei “luoghi urbani” collettivi è il fulcro dell’idea di architettura che porta alla costruzione della città. La ricerca si propone di studiare il contributo dato da Dudok al progetto dello sviluppo urbano della città olandese, considerando un arco temporale che va dal 1915, anno in cui l’architetto viene designato a ricoprire la carica di direttore del locale ufficio Lavori Pubblici, al 1954, anno simbolico della sua nomina a cittadino onorario di Hilversum. Il lavoro di ricerca vuole individuare quelle caratteristiche formali e tipologiche, insite nei quartieri progettati dall’architetto olandese, in grado di definire una struttura urbana capace di sostenere un ragionamento architettonico indipendente dal luogo e dal tempo, un ragionamento impostato sulla definizione della forma urbis. Non desidera certo delineare un modello, vista la consapevolezza che ogni progetto ha un proprio luogo e un proprio tempo, cerca di tratteggiare, piuttosto, uno scenario possibile per il progetto urbano, capace di assurgere ad exemplum per la costruzione della città. I progetti analizzati riguardano edifici residenziali e spazi urbani per la collettività; questi rappresentano veri e propri nuclei aggregativi per la costruzione dei complessi di alloggi popolari, dei quali definiscono la scena fissa delle vicende umane. Lo studio di questi quartieri rappresenta, pertanto, il tentativo di decodificare un “modo” di comporre la città dal quale sia possibile estrapolare temi validi e di carattere generale che permettano di formalizzare una serie di utili insegnamenti, tramite i quali poter pensare alla realizzazione della stessa, nella convinzione che “la qualità del progetto consiste nella qualità dei caratteri del tema e nel loro riconoscimento nelle forme dell’architettura”.

Probabilistic-based hurricane risk assessment and mitigation considering the potential impacts of climate change

Studies are suggesting that hurricane hazard patterns (e.g. intensity and frequency) may change as a consequence of the changing global climate. As hurricane patterns change, it can be expected that hurricane damage risks and costs may change as a result. This indicates the necessity to develop hurricane risk assessment models that are capable of accounting for changing hurricane hazard patterns, and develop hurricane mitigation and climatic adaptation strategies. This thesis proposes a comprehensive hurricane risk assessment and mitigation strategies that account for a changing global climate and that has the ability of being adapted to various types of infrastructure including residential buildings and power distribution poles. The framework includes hurricane wind field models, hurricane surge height models and hurricane vulnerability models to estimate damage risks due to hurricane wind speed, hurricane frequency, and hurricane-induced storm surge and accounts for the timedependant properties of these parameters as a result of climate change. The research then implements median insured house values, discount rates, housing inventory, etc. to estimate hurricane damage costs to residential construction. The framework was also adapted to timber distribution poles to assess the impacts climate change may have on timber distribution pole failure. This research finds that climate change may have a significant impact on the hurricane damage risks and damage costs of residential construction and timber distribution poles. In an effort to reduce damage costs, this research develops mitigation/adaptation strategies for residential construction and timber distribution poles. The costeffectiveness of these adaptation/mitigation strategies are evaluated through the use of a Life-Cycle Cost (LCC) analysis. In addition, a scenario-based analysis of mitigation strategies for timber distribution poles is included. For both residential construction and timber distribution poles, adaptation/mitigation measures were found to reduce damage costs. Finally, the research develops the Coastal Community Social Vulnerability Index (CCSVI) to include the social vulnerability of a region to hurricane hazards within this hurricane risk assessment. This index quantifies the social vulnerability of a region, by combining various social characteristics of a region with time-dependant parameters of hurricanes (i.e. hurricane wind and hurricane-induced storm surge). Climate change was found to have an impact on the CCSVI (i.e. climate change may have an impact on the social vulnerability of hurricane-prone regions).

Cobertura de la trinchera ferroviaria de Hendaya

Un problema del ferrocarril al paso por las ciudades europeas es el efecto barrera generado, que impide su desarrollo más allá de las vías. Si se salta la barrera lo cierto es que ello se hace sólo en sitios concretos y el efecto psicológico de aislamiento persiste para los habitantes del entorno. Este trabajo presenta de manera sucinta los problemas de concepción, comprobación y vibraciones planteados por la estructura de cubierta de la trinchera ferroviaria de Hendaya, consistente en una losa de hormigón pretensado y luz variable de 20-40 metros, que resuelve el problema de aislamiento entre las dos partes de la ciudad. Su construcción ha sido posible gracias al acuerdo entre la SNCF e inversores privados y está permitiendo la construcción sobre ella de 6 edificios de viviendas y una residencia de turismo, la demolición del antiguo ?Pont-Vieux? y la construcción de un nuevo ?Pont-Vieux?, integrado completamente en la promoción inmobiliaria. An important problem put by the train in its passage by the cities of Europe generally and in France in particular is the effect barrier which builds up, preventing the cities from developing beyond. Even if this barrier is crossed, it is certain that the passage is restricted to concrete places and always acts as psychological barrier for the local residents. This article presents in a brief way the problems of conception, analysis and vibration of the cover structure of the railroad trench of Hendaye. This structure consists of a 20-40 meters span slab of pre-stressed concrete that solves the isolation problem of both parts of the town of Hendaye. Its construction was possible thanks to the agreement of the SNCF (French Railways)and some private investors, and is allowing the investors the construction on top of 6 residential buildings and a holiday residence, with demolition of the ancient “Pont-Vieux” and building of a new “Pont-Vieux”, which is completely integrated into the real-estate development. Special attention is given to the change of transverse cross-section of the slab during construction stages, which originates a redistribution of stresses, and to the long-term equilibrium of horizontal forces.