An Exergy Based Engineering and Economic Analysis of Sustainable Building

To achieve the goal of sustainable development, the building energy system was evaluated from both the first and second law of thermodynamics point of view. The relationship between exergy destruction and sustainable development were discussed at first, followed by the description of the resource abundance model, the life cycle analysis model and the economic investment effectiveness model. By combining the forgoing models, a new sustainable index was proposed. Several green building case studies in U.S. and China were presented. The influences of building function, geographic location, climate pattern, the regional energy structure, and the technology improvement potential of renewable energy in the future were discussed. The building’s envelope, HVAC system, on-site renewable energy system life cycle analysis from energy, exergy, environmental and economic perspective were compared. It was found that climate pattern had a dramatic influence on the life cycle investment effectiveness of the building envelope. The building HVAC system energy performance was much better than its exergy performance. To further increase the exergy efficiency, renewable energy rather than fossil fuel should be used as the primary energy. A building life cycle cost and exergy consumption regression model was set up. The optimal building insulation level could be affected by either cost minimization or exergy consumption minimization approach. The exergy approach would cause better insulation than cost approach. The influence of energy price on the system selection strategy was discussed. Two photovoltaics (PV) systems – stand alone and grid tied system were compared by the life cycle assessment method. The superiority of the latter one was quite obvious. The analysis also showed that during its life span PV technology was less attractive economically because the electricity price in U.S. and China did not fully reflect the environmental burden associated with it. However if future energy price surges and PV system cost reductions were considered, the technology could be very promising for sustainable buildings in the future.

Damping Torque Analysis of Power Systems with DFIGs for Wind Power Generation

A grid-connected DFIG for wind power generation can affect power system small-signal angular stability in two ways: by changing the system load flow condition and dynamically interacting with synchronous generators (SGs). This paper presents the application of conventional method of damping torque analysis (DTA) to examine the effect of DFIG’s dynamic interactions with SGs on the small-signal angular stability. It shows that the effect is due to the dynamic variation of power exchange between the DFIG and power system and can be estimated approximately by the DTA. Consequently, if the DFIG is modelled as a constant power source when the effect of zero dynamic interactions is assumed, the impact of change of load flow brought about by the DFIG can be determined. Thus the total effect of DFIG can be estimated from the result of DTA added on that of constant power source model. Applications of the DTA method proposed in the paper are discussed. An example of multi-machine power systems with grid-connected DFIGs are presented to demonstrate and validate the DTA method proposed and conclusions obtained in the paper.

An iterative analytical design framework for the optimal designing of an off-grid renewable energy based hybrid smart micro-grid

Creative ways of utilising renewable energy sources in electricity generation especially in remote areas and particularly in countries depending on imported energy, while increasing energy security and reducing cost of such isolated off-grid systems, is becoming an urgently needed necessity for the effective strategic planning of Energy Systems. The aim of this research project was to design and implement a new decision support framework for the optimal design of hybrid micro grids considering different types of different technologies, where the design objective is to minimize the total cost of the hybrid micro grid while at the same time satisfying the required electric demand. Results of a comprehensive literature review, of existing analytical, decision support tools and literature on HPS, has identified the gaps and the necessary conceptual parts of an analytical decision support framework. As a result this research proposes and reports an Iterative Analytical Design Framework (IADF) and its implementation for the optimal design of an Off-grid renewable energy based hybrid smart micro-grid (OGREH-SμG) with intra and inter-grid (μG2μG & μG2G) synchronization capabilities and a novel storage technique. The modelling design and simulations were based on simulations conducted using HOMER Energy and MatLab/SIMULINK, Energy Planning and Design software platforms. The design, experimental proof of concept, verification and simulation of a new storage concept incorporating Hydrogen Peroxide (H2O2) fuel cell is also reported. The implementation of the smart components consisting Raspberry Pi that is devised and programmed for the semi-smart energy management framework (a novel control strategy, including synchronization capabilities) of the OGREH-SμG are also detailed and reported. The hybrid μG was designed and implemented as a case study for the Bayir/Jordan area. This research has provided an alternative decision support tool to solve Renewable Energy Integration for the optimal number, type and size of components to configure the hybrid μG. In addition this research has formulated and reported a linear cost function to mathematically verify computer based simulations and fine tune the solutions in the iterative framework and concluded that such solutions converge to a correct optimal approximation when considering the properties of the problem. As a result of this investigation it has been demonstrated that, the implemented and reported OGREH-SμG design incorporates wind and sun powered generation complemented with batteries, two fuel cell units and a diesel generator is a unique approach to Utilizing indigenous renewable energy with a capability of being able to synchronize with other μ-grids is the most effective and optimal way of electrifying developing countries with fewer resources in a sustainable way, with minimum impact on the environment while also achieving reductions in GHG. The dissertation concludes with suggested extensions to this work in the future.

Monitoring system for small sized photovoltaic power plants

This paper presents a monitoring system devoted to small sized photovoltaic (PV) power plants. The system is characterized by: a high level of integration; a low cost, when compared to the cost of the PV system to be monitored; and an easy installation in the majority of the PV plants with installed power of some kW. The system is able to collect, store, process and display electrical and meteorological parameters that are crucial when monitoring PV facilities. The identification of failures in the PV system and the elaboration of performance analysis of such facilities are other important characteristics of the developed system. The access to the information about the monitored facilities is achieved by using a web application, which was developed with a focus on the mobile devices. In addition, there is the possibility of an integration between the developed monitoring system and the central supervision system of Martifer Solar (a company focused on the development, operation and maintenance of PV systems).

Assessment of PV Systems Performance in the Madeira Island Using Typical Meteorological Year Data

This paper focus on the development of an algorithm using Matlab to generate Typical Meteorological Years from weather data of eight locations in the Madeira Island and to predict the energy generation of photovoltaic systems based on solar cells modelling. Solar cells model includes the effect of ambient temperature and wind speed. The analysis of the PV system performance is carried out through the Weather Corrected Performance Ratio and the PV system yield for the entire island is estimated using spatial interpolation tools.

Sistematização do dimensionamento técnico e econômico de sistemas fotovoltaicos isolados por meio de programa computacional

One of the main referring subjects to the solar energy is how to compare it economically with other sources of energy, as much alternatives as with conventionals (like the electric grid). The purpose of this work was to develop a software which congregates the technical and economic main data to identify, through methods of microeconomic analysis, the commercial viability in the sizing of photovoltaic systems, besides considering the benefits proceeding from the proper energy generation. Considering the period of useful life of the components of the generation system of photovoltaic electricity, the costs of the energy proceeding from the conventional grid had been identified. For the comparison of the conventional sources, electric grid and diesel generation, three scenes of costs of photovoltaic panels and two for the factor of availability of diesel generation had been used. The results have shown that if the cost of the panels is low and the place of installation is more distant of the electric grid, the photovoltaic system becomes the best option.

Estudo da eficiência de sistemas fotovoltaicos

Mestrado em Engenharia Química. Ramo optimização energética na indústria química

Elaboração de um projeto de uma central fotovoltaica de miniprodução e estudo de viabilidade técnica, económica e financeira

Desde o final do século XVIII, quando se iniciou a revolução industrial, o crescimento económico tem sido assente num consumo elevado de combustíveis fósseis que libertam gases com efeito de estufa. A emissão destes gases e a escassez dos combustíveis fósseis são temas que, desde as últimas duas décadas do século XX, ocupam um lugar de destaque nas agendas de política mundial. A produção de energia através de fontes renováveis surge como alternativa e poderá ser a solução para países com escassos recursos de origem fóssil, como é o caso de Portugal, minimizando também a sua dependência energética do exterior. Uma das medidas de incentivo lançada pelo Governo Português em 2007, foi a criação de um regime simplificado aplicável à microprodução descentralizada de eletricidade através de fontes de energia renováveis e de cogeração. À semelhança da maioria dos países europeus, o principal meio de promoção destes sistemas em Portugal foram as Feed-in-Tariffs, que consistem numa tarifa de venda de energia elétrica de origem renovável acima da tarifa de mercado. Estas tarifas permitiram, sobretudo, o crescimento do setor fotovoltaico em Portugal. Atualmente, o amadurecimento da tecnologia fotovoltaica, associado ao constante aumento das tarifas de energia elétrica, permite que se torne vantajosa a instalação de sistemas fotovoltaicos para autoconsumo. Neste contexto, o atual Governo Português, criou recentemente um regime jurídico aplicável à produção de eletricidade para autoconsumo. O objetivo deste trabalho é demonstrar, com base na minha experiência profissional, a metodologia de dimensionamento de uma central fotovoltaica ligada à Rede Elétrica de Serviço Público. Será utilizado como objeto de estudo um projeto constituído por 28 centrais fotovoltaicas de Miniprodução de 100 kW, dispersas por Portugal Continental, para o qual será efetuada a análise financeira do investimento. Pretende-se ainda apresentar o novo enquadramento legislativo para o Autoconsumo e Pequena Produção distribuída, detalhar as suas principais caraterísticas e efetuar um estudo económico para cada um destes regimes.

The impact of poor power quality in solar photovoltaic microgeneration: technical problems and losses of revenue

This paper presents a critical and quantitative analysis of the influence of the Power Quality in grid connected solar photovoltaic microgeneration installations. First are introduced the main regulations and legislation related with the solar photovoltaic microgeneration, in Portugal and Europe. Next are presented Power Quality monitoring results obtained from two residential solar photovoltaic installations located in the north of Portugal, and is explained how the Power Quality events affect the operation of these installations. Afterwards, it is described a methodology to estimate the energy production losses and the impact in the revenue caused by the abnormal operation of the electrical installation. This is done by comparing the amount of energy that was injected into the power grid with the theoretical value of energy that could be injected in normal conditions. The performed analysis shows that Power Quality severally affects the solar photovoltaic installations operation. The losses of revenue in the two monitored installations M1 and M2 are estimated in about 27% and 22%, respectively.

Matalakompleksisen palvelupyyntömallin kehittäminen palveluväylää hyödyntäviin järjestelmäintegraatioihin

Tässä työssä kehitetään yleiskäyttöinen palvelupyyntömalli, jonka avulla Lahden kaupungin Lahti Fenix –projektin Kuntalaistilijärjestelmän palveluväylän kautta voidaan kutsua järjestelmän tietokantatasoa tai muita palveluväylän avulla integroituja järjestelmiä. Työn tavoitteena oli suoraviivaistaa järjestelmäintegraatioihin liittyvien palveluiden kehittämistä suunnittelemalla sellainen palvelupyyntömuodostin, joka ei sisällä staattisia viittauksia jossakin tietyssä palvelussa käytettäviin luokkiin tai muihin ominaisuuksiin. Työssä hyödynnettiin Java-kielen kehittyneitä ominaisuuksia; reflektiivistä ohjelmointia, geneeristä ohjelmointia ja Java-virtuaalikoneen metodipinon lukemista. Tavoitteen saavuttamista mitattiin käyttäen avuksi McCaben syklomaattista kompleksisuutta ja metodeissa käytettyä rivimäärää. Työ aloitettiin joulukuussa 2008 ja saatiin valmiiksi helmikuussa 2009. Työn tuloksena syntyi toimiva, syklomaattiselta kompleksisuudeltaan matala ja helppokäyttöinen palvelukutsumuodostin.

Vapastii ohjelmoitavan automaatioyksikön suunnitteluprosessi

Rakennusautomaatiossa tulee esiin sovelluksia, joissa järjestelmän ohjaus-, säätö- tai valvontaratkaisun toteuttaminen ohjelmoitavilla logiikoilla ei ole riittävän edullista. Tällöin vaihtoehtona on oman laitteen suunnittelu. Työn tavoitteena oli suunnitella ja toteuttaa kustannustehokas CAN-väylään liitettävä vapaasti ohjelmoitava automaatioyksikkö. Suunnittelua ohjasivat asiakkaan laatimat vaatimusmäärittelyt. Niistä laitteen konfigurointimahdollisuudet ja piirilevyn tavoitekoko asettivat suurimmat haasteet laitteen suunnittelulle. Työn tuloksena toteutettiin asiakkaan tarpeisiin soveltuva automaatioyksikkö. Tavoitteisiin päästiin komponenttivalinnoilla ja hyödyntämällä tehokkaasti mikro-ohjaimen integroituja ominaisuuksia. Näiden avulla pystyttiin karsimaan monia yksiköitä, joita tavanomaisesti toteutetaan erilliskomponenteilla. Työssä perehdyttiin sulautetun järjestelmän elektroniikan tuotekehitysprosessiin ideasta prototyyppiin. Samalla on kuvailtu valittuja ratkaisuja sekä suunnittelussa tapahtuneita virheitä ja miten ne on ratkaistu.

Maalämpöpumpun ja aurinkosähköjärjestelmän yhteiskäyttö pientalon lämpimän käyttöveden tuotannossa

Tässä kandidaatintyössä tutkitaan maalämpöpumpun ja aurinkosähköjärjestelmän yhteis-käyttöä pientalon lämpimän käyttöveden tuotannossa. Tarkoituksena on tuottaa päivittäin tarvittava lämmin käyttövesi maalämpöpumpulla, jonka tarvitsema sähkö tuotetaan aurin-kosähköjärjestelmän avulla keskimäärin kello 12–15. Aurinkosähköjärjestelmän tuotto simuloidaan kuvitteelliselle Lappeenrannassa sijaitsevalle omakotitalolle Homer-ohjelmistolla. Maalämpöpumpun koko pidetään vakiona ja vertai-lussa on 4, 5 ja 6 kW:n kokoiset aurinkosähköjärjestelmät. Yli 5 kW:n aurinkosähköjärjestelmällä saadaan katettua talon peruskuorman lisäksi, myös maalämpöpumpun tarvitsema teho kyseisenä ajanjaksona. 4 kW:n aurinkosähköjärjestel-mällä ja maalämpöpumpulla saadaan tuotettua päivässä riittävästi energiaa neljän henkilön tarvitsemaan käyttöveteen, mutta tällöin maalämpöpumppua täytyy käyttää pidempi ajan-jakso, jos lämmitykseen halutaan käyttää vain tuotettua aurinkosähköä.

Entwicklung der Windenergietechnik in Deutschland und der Einfluss staatlicher Förderpolitik - Technikentwicklung in den 90er Jahren zwischen Markt und Forschungsförderung

Seit gut zehn Jahren erlebt die Windenergienutzung in Deutschland einen in der Mitte der 80er Jahre nicht für möglich gehaltenen Aufschwung. Anlagenanzahl und installierte Leistung haben in diesem Zeitraum mit durchschnittlichen jährlichen Wachstumsraten von mehr als 30 Prozent zugenommen, die mittlere installierte Leistung pro neu errichteter Anlage stieg dabei um das Zehnfache und die technische Verfügbarkeit der Anlagen liegt mittlerweile bei über 98 Prozent. Mit größer werdenden Anlagen zeigt sich weiterhin ein klarer Trend zu Blattwinkel verstellbaren Konzepten, mit zunehmend drehzahlvariabler Betriebsweise. Vor dem von Vielen für die kommenden drei bis sechs Jahre prognostizierten Einstieg in die großtechnische Offshore- Windenergienutzung mit den damit verbundenen immensen technologischen und strukturellen Herausforderungen erscheint es sinnvoll, einen kritischen Blick zurückzuwerfen auf die 90er Jahre mit den ihnen zugrunde liegenden förderpolitischen Rahmenbedingungen. Dabei soll die Frage beantwortet werden, welchen konkreten Einfluss die staatlichen Forschungs- und Förderprogramme, besonders das "250 MW Wind"-Programm, auf die Entwicklung der Windenergienutzung hatten, das heißt, unter welchen Bedingungen sich bestimmte Techniklinien durchsetzten, wie der Einfluss eines geschützten Marktes durch gesetzlich garantierte Einspeisetarife auf diese Entwicklung zu bewerten ist und schließlich, welche Fehlentwicklungen möglicher Weise eingetreten sind. Dazu wird mit Hilfe von Lernkurven gezeigt, welche Kostenreduktionen insgesamt erzielt wurden, wie hoch die dazu notwendigen staatlichen Finanzmittel waren und welche Schlussfolgerungen daraus für die Zukunft abgeleitet werden können. Die Arbeit soll insgesamt dazu beitragen, die erreichten technischen Entwicklungsschritte vor dem Hintergrund der förderpolitischen Gegebenheiten besser zu verstehen, Chancen für gezielte Änderungen in der Förderpraxis zu ergreifen und Hinweise auf die Ausgestaltung von zukünftigen Forschungsprogrammen und Entwicklungsschwerpunkten im Bereich der Windenergie zu geben, um weitere Kostensenkungspotenziale auszuschöpfen. Dabei wird sich die zukünftige Schwerpunktsetzung in der programmatischen Ausrichtung der Forschung stärker auf die drei wichtigsten Anwendungsfelder für Windenergieanlagen konzentrieren müssen, die großtechnische Offshore- Anwendung, die netzgebundene, dezentrale Energieversorgung sowie auf Windenergieanlagen zur ländlichen Elektrifizierung in autonomen Versorgungssystemen für Schwellen- und Entwicklungsländer.

Rapport från 20th European Photovoltaic Solar Energy Conference and Exhibition : Barcelona 6-10 juni 2005

På uppdrag av STEM bevakade Eva Lindberg från Centrum för solenergi-forskning, SERC, Högskolan Dalarna, 20th European Photovoltaic Solar Energy Conference and Exhibition, Barcelona, 6-10 juni 2005. Ca 1700 personer fanns på deltagarlistan. På grund av konferensen omfattning kan endast ett litet urval av föredrag och utställare kommenteras i rapporten. Konferensprogrammet var indelat på följande områden:1. Grundläggande fakta, nya komponenter och material2. Kristallina kiselsolceller and materialteknologi3. Amorft och mikrokristallint kisel4. CIS, CdTe och andra (II-VI) ternära tunnfilmsceller5. PV-moduler och komponenter i PV-system6. PV-system i nätanslutna applikationer7. Globala aspekter på PV-solelektricitet8. PV-industrins resultatFoU om kristallina solceller dominerade stort, sedan tunnfilmsceller av främst amorft kisel. Intressant var att återvinning är föremål för FoU; dels återvinning av kiselsolceller när panelen tjänat ut; dels återvinning av Cu, Cd, Se och Te när tunnfilmscellerna tas ur bruk.237 företag fanns representerade i utställningen, varav 20 från Kina. Tyskland dominerade stort. Utställningen teman var följande: 1) Tillverkare av kiselplattor, solceller, PV-moduler, koncentratorer, solföljare (se bild nedan) 2) Tillverkare och återförsäljare av utrustning och material 3) Integrering och distribution av system 4) Mätningar och kontrollteknologi 5) Forskning och laboratorier 6) Service, teknik, konsulting 7) Myndigheter och föreningar 8) Media och förlag 9) Tillverkare av inverterare 10) Övrigt.