Experimental study of the concentration field of discharge from a boat propeller

Two-stroke outboard boat engines using total loss lubrication deposit a significant proportion of their lubricant and fuel directly into the water. The purpose of this work is to document the velocity and concentration field characteristics of a submerged swirling water jet emanating from a propeller in order to provide information on its fundamental characteristics. The properties of the jet were examined far enough downstream to be relevant to the eventual modelling of the mixing problem. Measurements of the velocity and concentration field were performed in a turbulent jet generated by a model boat propeller (0.02 m diameter) operating at 1500 rpm and 3000 rpm in a weak co-flow of 0.04 m/s. The measurements were carried out in the Zone of Established Flow up to 50 propeller diameters downstream of the propeller, which was placed in a glass-walled flume 0.4 m wide with a free surface depth of 0.15 m. The jet and scalar plume development were compared to that of a classical free round jet. Further, results pertaining to radial distribution, self similarity, standard deviation growth, maximum value decay and integral fluxes of velocity and concentration were presented and fitted with empirical correlations. Furthermore, propeller induced mixing and pollutant source concentration from a two-stroke engine were estimated.

Preliminary characterisation of the surface of cartilage following exposure to saturated and unsaturated synthetic lipids

Articular cartilage is covered by a microscopic structure known as surface amorphous layer. This surface structure is often the first victim of attack during cartilage degeneration, thereby resulting in a gross impairment in cartilage function such as lubrication and load bearing. We hypothesize that incubation of degraded cartilage in solutions of different species of synthetic surface active phospholipids (saturated and unsaturated species) can remodel this lost surface structure. To test this hypothesis, the structural configuration of the surface of articular cartilage was studied and characterised with the lipid filled surface amorphous layer intact using the AFM. The results were then compared with those obtained following a systematic removal (delipidization) and replacement (relipidization) of this layer. Our results show that the unsaturated surfactant partially restored the lost surface amorphous layer while the saturated surfactant specie settled on the surface due to its poor solubility in aqueous solution.

Methods used in cross-cultural comparisons of sexual symptoms and their determinants

This is the fourth in a series of reviews of cross-cultural studies of menopausal symptoms. The purpose of this review is to examine methods used in cross-cultural comparisons of sexual symptoms among women at midlife, and to examine the determinants of sexual symptoms and how those determinants were measured. The goal of this review is to make recommendations that will improve cross-cultural comparisons in the future. The review included nine studies that explicitly examined symptoms in different countries or different ethnic groups in the same country and included: Australian/Japanese Midlife Women's Health Study (AJMWHS), Decisions At Menopause Study (DAMeS), Four Major Ethnic Groups (FMEG), Hilo Women's Health Survey (HWHS), Mid-Aged Health in Women from the Indian Subcontinent (MAHWIS), Penn Ovarian Aging Study (POAS), Study of Women's Health Across the Nation (SWAN), Women's Health in Midlife National Study (WHiMNS), and Women's International Study of Health and Sexuality (WISHeS). Although methods used for assessing sexual symptoms across cultures differed between studies, statistically significant differences were reported. Cross-cultural differences in sexual symptoms exist, and should be measured by including the following symptoms: loss of interest in sex, vaginal dryness, and the Females Sexual Function Index which covers desire, arousal, lubrication, orgasm, satisfaction, and pain on intercourse. The measurement of these symptoms will provide an evidence-based approach when forming any future menopause symptom list and allow for comparisons across studies.

A microanalytical study of the surfaces of normal, delipidized, and artificially “resurfaced” articular cartilage

The surface amorphous layer of articular cartilage is of primary importance to its load-bearing and lubrication function. This lipid-filled layer is degraded/disrupted or eliminated when cartilage degenerates due to diseases. This article examines further the characteristic of this surface overlay using a combination of microscopy and imaging methods to evaluate the hypothesis that the surface of articular cartilage can be repaired by exposing degraded cartilage to aqueous synthetic lipid mixtures. The preliminary results demonstrate that it is possible to create a new surface layer of phospholipids on the surface of cartilage following artificial lipid removal, but such a layer does not possess enough mechanical strength for physiological function when created with either unsaturated palmitoyloleoyl- phosphatidylcholine or saturated dipalmitoyl-phosphatidylcholine component of joint lipid composition alone. We conclude that this may be due to low structural cohesivity, inadequate time of exposure, and the mix/content of lipid in the incubation environment.

Not-for-profit ratios for financial resilience and internal accountability : a study of Australian international aid organisations

Not-for-profit (NFP) financial ratio research has focused primarily on organisational efficiency measurements for external stakeholders. Ratios that also capture information about stability, capacity (liquidity), gearing and sustainability, enable an assessment of financial resilience. They are thus valuable tools that can provide a framework of internal accountability between boards and management. The establishment of an Australian NFP regulator highlights the importance of NFP sustainability, and affirms the timeliness of this paper. We propose a suite of key financial ratios for use by NFP boards and management, and demonstrate its practical usefulness by applying the ratios to financial data from the 2009 reports of ACFID (Australian Council for International Development)-affiliated international aid organisations.

Gravity-driven fingering simulations for a thin liquid film flowing down the outside of a vertical cylinder

A numerical study is presented to examine the fingering instability of a gravity-driven thin liquid film flowing down the outer wall of a vertical cylinder. The lubrication approximation is employed to derive an evolution equation for the height of the film, which is dependent on a single parameter, the dimensionless cylinder radius. This equation is identified as a special case of that which describes thin film flow down an inclined plane. Fully three-dimensional simulations of the film depict a fingering pattern at the advancing contact line. We find the number of fingers observed in our simulations to be in excellent agreement with experimental observations and a linear stability analysis reported recently by Smolka & SeGall (Phys Fluids 23, 092103 (2011)). As the radius of the cylinder decreases, the modes of perturbation have an increased growth rate, thus increasing cylinder curvature partially acts to encourage the contact line instability. In direct competition with this behaviour, a decrease in cylinder radius means that fewer fingers are able to form around the circumference of the cylinder. Indeed, for a sufficiently small radius, a transition is observed, at which point the contact line is stable to transverse perturbations of all wavenumbers. In this regime, free surface instabilities lead to the development of wave patterns in the axial direction, and the flow features become perfectly analogous to the two-dimensional flow of a thin film down an inverted plane as studied by Lin & Kondic (Phys Fluids 22, 052105 (2010)). Finally, we simulate the flow of a single drop down the outside of the cylinder. Our results show that for drops with low volume, the cylinder curvature has the effect of increasing drop speed and hence promoting the phenomenon of pearling. On the other hand, drops with much larger volume evolve to form single long rivulets with a similar shape to a finger formed in the aforementioned simulations.

Harnessing the power of real and virtual social networks during disasters

The mass media and emergency services organisations routinely gather information and disseminate it to the public. During disaster situations both the media and emergency services require acute situational awareness. New social media technologies offer opportunities to enhance situational awareness by crowd-sourcing information using real and virtual social networks. This paper documents how real and virtual social networks were used by a reporter and by members of the public to gather and disseminate emergency information during the flash flood disaster in Toowoomba and the Lockyer Valley in January 2011 and in the days and weeks after the disaster.

Lessons from media reporting of natural disasters : a case study of the 2011 flash floods in Toowoomba and the Lockyer Valley

Practice-led journalism research techniques were used in this study to produce a ‘first draft of history’ recording the human experience of survivors and rescuers during the January 2011 flash flood disaster in Toowoomba and the Lockyer Valley in Queensland, Australia. The study aimed to discover what can be learnt from engaging in journalistic reporting of natural disasters. This exegesis demonstrates that journalism can be both a creative practice and a research methodology. About 120 survivors, rescuers and family members of victims participated in extended interviews about what happened to them and how they survived. Their stories are the basis for two creative outputs of the study: a radio documentary and a non-fiction book, that document how and why people died, or survived, or were rescued. Listeners and readers are taken "into the flood" where they feel anxious for those in peril, relief when people are saved, and devastated when babies, children and adults are swept away to their deaths. In undertaking reporting about the human experience of the floods, several significant elements about journalistic reportage of disasters were exposed. The first related to the vital role that the online social media played during the disaster for individuals, citizen reporters, journalists and emergency services organisations. Online social media offer reporters powerful new reporting tools for both gathering and disseminating news. The second related to the performance of journalists in covering events involving traumatic experiences. Journalists are often required to cover trauma and are often amongst the first-responders to disasters. This study found that almost all of the disaster survivors who were approached were willing to talk in detail about their traumatic experiences. A finding of this project is that journalists who interview trauma survivors can develop techniques for improving their ability to interview people who have experienced traumatic events. These include being flexible with interview timing and selecting a location; empowering interviewees to understand they don’t have to answer every question they are asked; providing emotional security for interviewees; and by being committed to accuracy. Survivors may exhibit posttraumatic stress symptoms but some exhibit and report posttraumatic growth. The willingness of a high proportion of the flood survivors to participate in the flood research made it possible to document a relatively unstudied question within the literature about journalism and trauma – when and why disaster survivors will want to speak to reporters. The study sheds light on the reasons why a group of traumatised people chose to speak about their experiences. Their reasons fell into six categories: lessons need to be learned from the disaster; a desire for the public to know what had happened; a sense of duty to make sure warning systems and disaster responses to be improved in future; personal recovery; the financial disinterest of reporters in listening to survivors; and the timing of the request for an interview. Feedback to the creative-practice component of this thesis - the book and radio documentary - shows that these issues are not purely matters of ethics. By following appropriate protocols, it is possible to produce stories that engender strong audience responses such as that the program was "amazing and deeply emotional" and "community storytelling at its most important". Participants reported that the experience of the interview process was "healing" and that the creative outcome resulted in "a very precious record of an afternoon of tragedy and triumph and the bitter-sweetness of survival".

An isoviscous, isothermal model investigating the influence of hydrostatic recesses on a spring-supported tilting pad thrust bearing

Tilting-pad hydrodynamic thrust bearings are used in hydroelectric power stations around the world, reliably supporting turbines weighing hundreds of tonnes, over decades of service. Newer designs incorporate hydrostatic recesses machined into the sector-shaped pads to enhance oil film thickness at low rotational speeds. External pressurisation practically eliminates wear and enhances service life and reliability. It follows that older generating plants, lacking such assistance, stand to benefit from being retrofitted with hydrostatic lubrication systems. The design process is not trivial however. The need to increase the groove size to permit spontaneous lifting of the turbine under hydrostatic pressure, conflicts with the need to preserve performance of the original plane pad design. A haphazardly designed recess can induce a significant rise in bearing temperature concomitant with reduced mechanical efficiency and risk of thermal damage. In this work, a numerical study of a sector-shaped pad is undertaken to demonstrate how recess size and shape can affect the performance of a typical bearing.

An exploratory study of the potential of resurfacing articular cartilage with synthetic phospholipids

This thesis is aimed at further understanding the uppermost lipid-filled membranous layer (i.e. surface amorphous layer (SAL)) of articular cartilage and to develop a scientific framework for re-introducing lipids onto the surface of lipid-depleted articular cartilage (i.e. "resurfacing"). The outcome will potentially contribute to knowledge that will facilitate the repair of the articular surface of cartilage where degradation is limited to the loss of the lipids of the SAL only. The surface amorphous layer is of utmost importance to the effective load-spreading, lubrication, and semipermeability (which controls its fluid management, nutrient transport and waste removal) of articular cartilage in the mammalian joints. However, because this uppermost layer of cartilage is often in contact during physiological function, it is prone to wear and tear, and thus, is the site for damage initiation that can lead to the early stages of joint condition like osteoarthritis, and related conditions that cause pain and discomfort leading to low quality of life in patients. It is therefore imperative to conduct a study which offers insight into remedying this problem. It is hypothesized that restoration (resurfacing) of the surface amorphous layer can be achieved by re-introducing synthetic surface-active phospholipids (SAPL) into the joint space. This hypothesis was tested in this thesis by exposing cartilage samples whose surface lipids had been depleted to individual and mixtures of synthetic saturated and unsaturated phospholipids. The surfaces of normal, delipidized, and relipidized samples of cartilage were characterized for their structural integrity and functionality using atomic force microscope (AFM), confocal microscope (COFM), Raman spectroscopy, magnetic resonance imaging (MRI) with image processing in the MATLAB® environment and mechanical loading experiments. The results from AFM imaging, confocal microscopy, and Raman spectroscopy revealed a successful deposition of new surface layer on delipidized cartilage when incubated in synthetic phospholipids. The relipidization resulted in a significant improvement in the surface nanostructure of the artificially degraded cartilage, with the complete SAPL mixture providing better outcomes in comparison to those created with the single SAPL components (palmitoyl-oleoyl-phosphatidylcholine, POPC and dipalmitoyl-phosphatidylcholine, DPPC). MRI analysis revealed that the surface created with the complete mixture of synthetic lipids was capable of providing semipermeability to the surface layer of the treated cartilage samples relative to the normal intact surface. Furthermore, deformation energy analysis revealed that the treated samples were capable of delivering the elastic properties required for load bearing and recovery of the tissue relative to the normal intact samples, with this capability closer between the normal and the samples incubated in the complete lipid mixture. In conclusion, this thesis has established that it is possible to deposit/create a potentially viable layer on the surface of cartilage following degradation/lipid loss through incubation in synthetic lipid solutions. However, further studies will be required to advance the ideas developed in this thesis, for the development of synthetic lipid-based injections/drugs for treatment of osteoarthritis and other related joint conditions.

Bearing Fault Diagnostics Using the Spectral Pattern Recognition

In the field of diagnostics of rolling element bearings, the development of sophisticated techniques, such as Spectral Kurtosis and 2nd Order Cyclostationarity, extended the capability of expert users to identify not only the presence, but also the location of the damage in the bearing. Most of the signal-analysis methods, as the ones previously mentioned, result in a spectrum-like diagram that presents line frequencies or peaks in the neighbourhood of some theoretical characteristic frequencies, in case of damage. These frequencies depend only on damage position, bearing geometry and rotational speed. The major improvement in this field would be the development of algorithms with high degree of automation. This paper aims at this important objective, by discussing for the first time how these peaks can draw away from the theoretical expected frequencies as a function of different working conditions, i.e. speed, torque and lubrication. After providing a brief description of the peak-patterns associated with each type of damage, this paper shows the typical magnitudes of the deviations from the theoretical expected frequencies. The last part of the study presents some remarks about increasing the reliability of the automatic algorithm. The research is based on experimental data obtained by using artificially damaged bearings installed in a gearbox.

Trauma overload

Reporting on death and accidents in regional and rural areas can exact a heavy toll on reporters. News reporters necessarily report on trauma. Overseas correspondents who report from war zones or areas of conflict or natural disaster are often exposed to physical risk and are sometimes required to confront extreme trauma. To an extent reporters embarking on overseas assignments are mentally prepared to face traumatic situations. Their supervisors are more or less aware of the reporter’s isolation and vulnerability...

Why disaster survivors speak to reporters

Practice-led journalism research techniques were used in this study to produce a ‘first draft of history’ recording the human experience of survivors and rescuers during the January 2011 flash flood disaster in Toowoomba and the Lockyer Valley in Queensland, Australia. The study aimed to discover what can be learnt from engaging in journalistic reporting of natural disasters, using journalism as both a creative practice and a research methodology. (Lindgren and Phillips, 2011, 75). The willingness of a very high proportion of severely traumatised flood survivors to participate in the flood research was unexpected but made it possible to document a relatively unstudied question within the literature about journalism and trauma – when and why disaster survivors will want to speak to journalists. The study reports six categories of reasons interviewees gave for their willingness to speak to the media: for their own personal recovery; their desire for the public to know what had happened; that lessons need to be learned from the disaster; their sense of duty to make sure warning systems and disaster responses are improved in future; the financial disinterest of reporters in listening to survivors; and the timing of the request for an interview. In addition, traumatised flood survivors found both the opportunity to speak to the media and the journalistic outputs of the research cathartic in their recovery.

Global story-telling in a socially-networked world

Journalists work in an intensively time-pressured environment, researching and writing to daily, often 24 hour, deadlines and always aware of the competition with other news outlets to be first with the news. This results, as Karen Sanders has observed, in journalists having very little time for reflection. “If they do reflect, it’s usually after a decision has been made” (Sanders 2003, 168). Yet time for reflection upon professional practice is important, especially in an era of extremely rapid and seismic technological change in the global media. This paper will reflect upon how freelance journalists can use advances in social media and web-based connectedness to tell global stories via mainstream media outlets. In exploring this question, I will examine the techniques and communications technologies used by three reporters working in the UK and Australia to find, investigate and break a series of articles, published simultaneously on the front pages of The Australian and The Times (London) newspapers, was a result of a six month investigation. The series exposed a 50-year cover-up of the serial abuse of children by one of the Church of England's most senior clergy, Robert Waddington, in Australia and the UK. It unearthed the existence of a culture of physical and sexual abuse at St Barnabas boarding school in Queensland, the sudden closure of the school and disappearance of student files - as well as Waddington's subsequent offences against children while Dean of Manchester Cathedral. We produced more than 20 articles. The coverage sparked church-ordered investigations in both countries, and also prompted the Archbishop of Canterbury to order a commission of inquiry – headed by a sitting UK judge - as well as a nationwide child safety audit of dioceses in Britain. In Australia, the church referred the case and handed its files to the Royal Commission into Child Sexual Abuse. The coverage marked the first publishing collaboration between The Australian and The Times to break an exclusive story in Australia and Britain simultaneously, on May 10, 2013.

Animal stories : flash flood 2011

Flash flood disasters happen suddenly. The Toowoomba Lockyer Valley flash flood in January 2011 was not forecast by the Bureau of Meteorology until after it had occurred. Domestic and wild animals gave the first warning of the disaster in the days leading up to the event and large animals gave warnings on the morning of the disaster. Twenty-three people, including 5 children in the disaster zone died. More than 500 people were listed as missing. Some of those who died, perished because they stayed in the disaster zone to look after their animals while other members of their family escaped to safety. Some people who were in danger refused to be rescued because they could not take their pets with them. During a year spent recording accounts of the survivors of the disaster, animals were often mentioned by survivors. Despite the obvious perils, people risked their lives to save their animals; people saw animals try to save each other; animals rescued people; people rescued animals; animals survived where people died; animals were used to find human victims in the weeks after the disaster; and animals died. The stories of the flood present challenges for pet owners, farmers, counter disaster planners, weather forecasters and emergency responders in preparing for disasters, responding to them and recovering after them.