Development of the Combined Method for Designing Dataflow Systems

The methods of designing of information systems for large organizations are considered in the paper. The structural and object-oriented approaches are compared. For the practical realization of the automated dataflow systems the combined method for the system development and analysis is proposed.

Development of surface flaw thresholds for pre-cured fiber reinforced polymer and groove size tolerance for near surface mounted fiber reinforced polymer retrofit systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. This study was conducted as part of the National Cooperative Highway Research Program (NCHRP) Project 10-59B to develop construction specifications and process control manual for repair and retrofit of concrete structures using bonded FRP systems. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The bond interface between FRP and concrete was modeled by a series of nonlinear springs. The model was validated against test data from the present study as well as those available from the literature. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of ±1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Development of Surface Flaw Thresholds for Pre-Cured Fiber Reinforced Polymer and Groove Size Tolerance for Near Surface Mounted Fiber Reinforced Polymer Retrofit Systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems, and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of +1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Development of hardware in the loop real-time control techniques for hybrid power systems involving distributed demands and sustainable energy sources

The future power grid will effectively utilize renewable energy resources and distributed generation to respond to energy demand while incorporating information technology and communication infrastructure for their optimum operation. This dissertation contributes to the development of real-time techniques, for wide-area monitoring and secure real-time control and operation of hybrid power systems. ^ To handle the increased level of real-time data exchange, this dissertation develops a supervisory control and data acquisition (SCADA) system that is equipped with a state estimation scheme from the real-time data. This system is verified on a specially developed laboratory-based test bed facility, as a hardware and software platform, to emulate the actual scenarios of a real hybrid power system with the highest level of similarities and capabilities to practical utility systems. It includes phasor measurements at hundreds of measurement points on the system. These measurements were obtained from especially developed laboratory based Phasor Measurement Unit (PMU) that is utilized in addition to existing commercially based PMU’s. The developed PMU was used in conjunction with the interconnected system along with the commercial PMU’s. The tested studies included a new technique for detecting the partially islanded micro grids in addition to several real-time techniques for synchronization and parameter identifications of hybrid systems. ^ Moreover, due to numerous integration of renewable energy resources through DC microgrids, this dissertation performs several practical cases for improvement of interoperability of such systems. Moreover, increased number of small and dispersed generating stations and their need to connect fast and properly into the AC grids, urged this work to explore the challenges that arise in synchronization of generators to the grid and through introduction of a Dynamic Brake system to improve the process of connecting distributed generators to the power grid.^ Real time operation and control requires data communication security. A research effort in this dissertation was developed based on Trusted Sensing Base (TSB) process for data communication security. The innovative TSB approach improves the security aspect of the power grid as a cyber-physical system. It is based on available GPS synchronization technology and provides protection against confidentiality attacks in critical power system infrastructures. ^

Development of a transitioning approach to reduce surface water volumes in combined sewer systems

The overarching goal of this research is to establish a successful forum for a transition from the existing paradigm of managing wastewater infrastructure to a more sustainable paradigm that achieves a more efficient utilisation of wastewater assets. A transitioning approach to support a more efficient utilisation of surface water and wastewater assets and infrastructure is proposed and developed. The determined transitioning approach possesses key stages namely developing the arena, developing the agenda, case study, and monitoring. The case study stage investigates a drainage utility identifying their improvement drivers, the removal of surface water through detailed drainage modelling and the financial examination of the costs incurred under the various scenarios conducted. Understanding the implications of removing/attenuating surface water from the network is improved through obtaining data by detailed drainage modelling. Infoworks software is used to investigate and assess the current and future operational scenarios of a wastewater system operating over one calendar year. Modelling scenarios were conducted removing surface water from selected areas focusing on the volumes requiring pumping and durations of pumping station(s) operation prior to treatment during storm conditions. The financial implication of removing surface water in combined sewer systems is examined in three main components. Firstly the costs of electricity incurred at the single sewage pumping station (SPS) investigated during the various scenarios modelled require to be addressed. Secondly the costs to retrofit sustainable urban drainage system (SUDS) solutions needs to be identified. Thirdly the implications of removing surface water for the drainage utility at the national level and the potential saving for householder’s committing to a surface water disconnection rebate scheme. When addressed at the macro level i.e., with over 2,100 pumping stations, some operating in sequence and contained within one drainage utility annually treating 315,360 megalitres the significance of the same multiple quantifiable and intangible benefits becomes amplified. The research aims, objectives and findings are presented to the identified and convened stakeholders. The transitioning approach developed encourages positive discourse between stakeholders. The level of success of the transitioning approach determined is then tested using a quantitative methodology through the completion of questionnaires. From the questionnaires completed the respondents unanimously agreed that surface water flows should be removed as well as reduced from the combined sewer system. The respondents agreed that the removal of surface water from a typical combined sewer system is justified by applying a transitioning approach focusing on the energy consumption required to pump increased volumes during storm events. This response is significant based upon the economic evidence and is contrary to the respondents previous position that finance was their most influencing factor. When provided with other potentially available benefits the respondents were even more supportive of the justification to remove surface water from the combined sewer system. The combined findings of the work presented in this thesis provide further justification that the transitioning approach applied to the removal of surface water from a typical combined sewer system, as determined in this research has been successful.

Development of sexing systems functional to mass production of Aedes albopictus sterile males

Aedes albopictus is a vector able to transmit several arboviruses. Due to its high impact on human health, it is important to develop an efficient control strategy for this pest. Nowadays, control based on chemical insecticides is limited by the number of available active principles and the occurrence of resistance. A valuable alternative to the conventional control strategies is the sterile insect technique (SIT) which relies on releasing sterile males of the target insect. Mating between wild females and sterile males results in no viable offspring. A crucial aspect of SIT is the production of a large number of sterile males with a low presence of females that can bite and transmit viruses. The present thesis aimed to find, implement and study the most reliable mechanical sex sorter and protocol to implement male productivity and reduce female contamination. In addition, I evaluated different variables and sorting protocols to enable female recovery for breeding purposes. Furthermore, I studied the creation of a hyper-protandric strain potentially able to produce only males. I also assessed the integration of artificial intelligence with an optical unit to identify sexes at the adult stage. All these applications helped to realise a mass production model in Italy with a potential weekly production of 1 million males. Moreover, I studied and applied for aerial sterile male release in an urban environment. This technology could allow the release of males in a wide area, overcoming environmental and urban obstacles. However, the development and application of drone technologies in a metropolitan area close to airports, such as in Bologna area, must fit specific requirements. Lastly, at Réunion Island, during a Short Term Scientific Mission France (AIM-COST Action), Indian Ocean, I studied the Boosted SIT application. Coating sterile males with Pyriproxyfen may help spread the insecticide into the larval breeding sites.

Analysis and development of interface components and procedures for the design and commissioning toolchains in automation systems

The objective of the thesis project, developed within the Line Control & Software Engineering team of G.D company, is to analyze and identify the appropriate tool to automate the HW configuration process using Beckhoff technologies by importing data from an ECAD tool. This would save a great deal of time, since the I/O topology created as part of the electrical planning is presently imported manually in the related SW project of the machine. Moreover, a manual import is more error-prone because of human mistake than an automatic configuration tool. First, an introduction about TwinCAT 3, EtherCAT and Automation Interface is provided; then, it is analyzed the official Beckhoff tool, XCAD Interface, and the requirements on the electrical planning to use it: the interface is realized by means of the AutomationML format. Finally, due to some limitations observed, the design and implementation of a company internal tool is performed. Tests and validation of the tool are performed on a sample production line of the company.

Development of instrumentation for amperometric and coulometric detection using ultramicroelectrodes

In this work it is presented the development of a simple, portable and inexpensive instrumentation for amperometric and coulometric detection in different analytical instrumentation systems utilizing ultramicroelectrodes. The software, developed in LabVIEW 7.1TM, is capable to carry out three main detection techniques (amperometric, pulsed amperometric and coulometric detection) and a voltammetric technique (cyclic voltammetry). The instrumentation was successfully evaluated using the following systems: cyclic voltammograms of metallic electrodes in alkaline solutions, flow electrochemical detection of glucose and glycine and direct determination of herbicide glyphosate (electrochemical detection coupled to HPLC).

Development of Control Systems for Safety Instrumented Systems

Safety Instrumented Systems (SIS) are designed to prevent and / or mitigate accidents, avoiding undesirable high potential risk scenarios, assuring protection of people`s health, protecting the environment and saving costs of industrial equipment. The design of these systems require formal methods for ensuring the safety requirements, but according material published in this area, has not identified a consolidated procedure to match the task. This sense, this article introduces a formal method for diagnosis and treatment of critical faults based on Bayesian network (BN) and Petri net (PN). This approach considers diagnosis and treatment for each safety instrumented function (SIF) including hazard and operability (HAZOP) study in the equipment or system under control. It also uses BN and Behavioral Petri net (BPN) for diagnoses and decision-making and the PN for the synthesis, modeling and control to be implemented by Safety Programmable Logic Controller (PLC). An application example considering the diagnosis and treatment of critical faults is presented and illustrates the methodology proposed.

Effect of body composition at selection on reproductive development in large white gilts

Fifty-four Large White gilts were used to determine the effect of body composition at selection (145 d of age) on the onset of puberty and subsequent reproductive development until 202 d of age. Gilts were assigned to one of three groups based on their backfat depth at selection: 10 to 12 mm (L), 13 to 15 mm (M), and 16 to 18 mm (F). All of the F gilts, 92% of the M gilts, and 67% of the L gilts reached puberty by slaughter at 202 d of age. Data from a subgroup (first 67% to reach puberty in each group; L = Lp, M = Mp, and F = Fp) was also used. The M (Mp) and F (Fp) gilts reached puberty at 172 d (166 d) and 170 d (166 d) of age, respectively, but the L (Lp) gilts at 184.5 d were 12 d (18 d) older than M(P < .05), Mp(P < .001), and F(P < .01), Fp (P < .001) gilts. The Lp (97.68 kg) and Mp (98.33 kg) gilts were lighter (P < .01) than Fp (108.72 kg) gilts at puberty. There were no differences (P < .05) among the L, M, and F gilts in terms of backfat depth or weight at puberty. The L (Lp) gilts had a mean of 1.16 (1.75) estrous cycles, which was lower (P < .01) than for M (Mp) and (P < .01) F (Fp) gilts, with 1.96 (2.29) and 2.25 (2.33) cycles, respectively. L (Lp) gilts had fewer (P < .05) follicles, 13.14 (12.63), than either M (Mp), 19.08 (18.71), or F (Fp), 18.25 (17.42) gilts. The number of corpora lutea was not influenced (P > .05) by grouping at selection, but Fp gilts had fewer (P < .05) corpora lutea than Mp or Fp gilts. Live weight at slaughter was not influenced (P > .10) by grouping at selection or subgrouping at puberty. The L gilts with a mean of 18.05 mm of backfat at slaughter were leaner (P < .05) than the F (21.66 mm) but not (P > .10) the M gilts (19.41 mm). Subgrouping had no effect. Fat deposition and protein deposition were higher (P < .05) in those animals that attained puberty. We conclude that the rate of fat and protein deposition seems to be one of the determinants of puberty attainment.

Neoskin development in the fetus with the use of a three-layer graft: an animal model for in utero closure of large skin defects

Objective: To assess the ability of a three-layer graft in the closuse of large fetal skin defects. Methods: Ovine fetuses underwent a large (4 x 3 cm) full-thickness skin defect over the lumbar region at 105 days` gestation (term = 140 days). A bilaminar artificial skin was placed over a cellulose interface to cover the defect (3-layer graft). The skin was partially reapproximated with a continuous nylon suture. Pregnancy was allowed to continue and the surgical site was submitted to histopathological analysis at different post-operative intervals. Results: Seven fetuses underwent surgery. One maternal/fetal death occurred, and the remaining 6 fetuses were analyzed. Artificial skin adherence to the wound edges was observed in cases that remained in utero for at least 15 days. Neoskin was present beneath the silicone layer of the bilaminar artificial skin. Conclusions: Our study shows that neoskin can develop in the fetus using a 3-layer graft, including epidermal growth beneath the silicone layer of the bilaminar skin graft. These findings suggest that the fetus is able to reepithelialise even large skin defects. Further experience is necessary to assess the quality of this repair.

An analysis of why telehealth systems in Australia have not always succeeded

Telehealth programmes are rather similar to humans in the way that they are planned, develop, grow and ultimately die or disappear. To achieve good life expectancy for a telehealth programme there appear to be three major needs: nurturing, which includes the provision of money, ideas, education, training and innovation; experience, which involves an integrated management process, the achievement of long and wide patterns of usage, the development of updated policies and procedures and the involvement of multiple disciplines; success, which involves evidence of outcomes, evaluation and research, and, most important, the sharing of information through scientific and popular press publications, and conferences and collaborations with internal and external groups. The future of telehealth in Australia is at a watershed. There are now a substantial number of programmes, and there has been a large amount of financial and human investment in telehealth around the nation. There is, however, no forum for national leadership, no national association and little support at federal government level.

Increasing profits and reducing risks in crop production using participatory systems simulation approaches

The development of cropping systems simulation capabilities world-wide combined with easy access to powerful computing has resulted in a plethora of agricultural models and consequently, model applications. Nonetheless, the scientific credibility of such applications and their relevance to farming practice is still being questioned. Our objective in this paper is to highlight some of the model applications from which benefits for farmers were or could be obtained via changed agricultural practice or policy. Changed on-farm practice due to the direct contribution of modelling, while keenly sought after, may in some cases be less achievable than a contribution via agricultural policies. This paper is intended to give some guidance for future model applications. It is not a comprehensive review of model applications, nor is it intended to discuss modelling in the context of social science or extension policy. Rather, we take snapshots around the globe to 'take stock' and to demonstrate that well-defined financial and environmental benefits can be obtained on-farm from the use of models. We highlight the importance of 'relevance' and hence the importance of true partnerships between all stakeholders (farmer, scientists, advisers) for the successful development and adoption of simulation approaches. Specifically, we address some key points that are essential for successful model applications such as: (1) issues to be addressed must be neither trivial nor obvious; (2) a modelling approach must reduce complexity rather than proliferate choices in order to aid the decision-making process (3) the cropping systems must be sufficiently flexible to allow management interventions based on insights gained from models. The pro and cons of normative approaches (e.g. decision support software that can reach a wide audience quickly but are often poorly contextualized for any individual client) versus model applications within the context of an individual client's situation will also be discussed. We suggest that a tandem approach is necessary whereby the latter is used in the early stages of model application for confidence building amongst client groups. This paper focuses on five specific regions that differ fundamentally in terms of environment and socio-economic structure and hence in their requirements for successful model applications. Specifically, we will give examples from Australia and South America (high climatic variability, large areas, low input, technologically advanced); Africa (high climatic variability, small areas, low input, subsistence agriculture); India (high climatic variability, small areas, medium level inputs, technologically progressing; and Europe (relatively low climatic variability, small areas, high input, technologically advanced). The contrast between Australia and Europe will further demonstrate how successful model applications are strongly influenced by the policy framework within which producers operate. We suggest that this might eventually lead to better adoption of fully integrated systems approaches and result in the development of resilient farming systems that are in tune with current climatic conditions and are adaptable to biophysical and socioeconomic variability and change. (C) 2001 Elsevier Science Ltd. All rights reserved.

Effect of restricted feed intake on early reproductive development in Large White gilts

Forty-five Large White gilts were used to study the effect of energy intake from 28 to 176 d of age on body composition and reproductive development. From 28 to 60 d, the gilts were fed ad libitum a 16.6 MJ DE/kg, 24% crude protein and 1.3% total lysine diet. From 61 d of age three dietary treatments were used; 1) ad libitum access to feed (15.6 MJ DE/kg, 21% crude protein and 1.07% total lysine) (H), 2) feed offered at 75% (M) of the previous days intake of H, and 3) feed offered at 60% (L) of the previous days intake of H. ADG from 61 to 176 d of age was (p <0.05) affected by treatment. Although live weight at 176 d of age did not differ (p >0.1) the H gilts had higher (p <0.08) carcass weights than the M or L gilts. Back fat depths were similar (p >0.1) for all treatments at 115 d of age, however by 176 d of age M and H gilts were fatter (p <0.1) than L gilts. The mean lipid deposition (LD) from 115 to 176 d of age for L gilts (78.9 g/d) was less (p <0.05) than for M gilts (143.6 g/d) and H gilts (135.6 g/d). There were no differences between treatments for protein deposition (PD) over the same period. More (p <0.05) H gilts (n=8) attained puberty (first observed estrus) than either M gilts or L gilts (n=4 for both). Follicle numbers were similar (p >0.1) across treatments. For gilts that attained puberty, H gilts had fewer (p <0.05) follicles (13.5) than M gilts (19.7) and L gilts (21.3). For gilts with follicular development, H gilts had the heaviest (458.7 g) reproductive tract weight (RTW). However, for those that attained puberty, L gilts had the heaviest RTW. RTW were lowest for those with no follicular development. Energy restriction had a negative impact on puberty attainment, i.e. it took longer to reach puberty. However, for gilts that attained puberty, the number of follicles was greater for those on lower feed intakes. It would appear that rate of fat deposition, but not necessarily the total amount of fat, plays an important role in puberty attainment.