Color and shade parameters of ultramarine zeolitic pigments synthesized from kaolin waste

Ultramarine pigments were successful synthesized from zeolite A obtained from kaolin waste. This waste has been used as an excellent source of silicon and aluminum for zeolite synthesis because of its high kaolinite concentrations and low contents of other accessory minerals. The cost is naturally less than the industrialized product. Color additives (Sulfur and Sodium Carbonate) were mixed with different proportions of zeolite A and further calcined for 5 h at 500 °C. They were characterized by XRD and XRF in addition to visual classification by color and shade. These products show colors from blue to green at different shades, both influenced by the amount of additives and cooling rate after calcination. Thus, a different quantity of the same additives in the same zeolitic matrix provides an increase in the color intensity. Cooling rate after calcination induces the color change which is substantially important in the pigments production.

Síntese de pigmentos zeolíticos a partir de zeólita A derivada de rejeito de caulim da Amazônia

Pigmentos tipo ultramar foram sintetizados com sucesso a partir de zeólita NaA derivada de caulim e rejeito de caulim. Tal rejeito tem sido uma excelente fonte de silício e alumínio na síntese de zeólitas, por ser uma matéria-prima “natural” com alta concentração de caulinita e baixos teores de impurezas, além do menor custo em comparação àquelas matérias-primas industrializadas. A zeólita NaA derivada de tal rejeito apresenta características estruturais favoráveis a síntese de pigmentos ultramar, sua estrutura encapsula as espécies de enxofre formadas, que agem como cromóforos, e impedem que essas espécies se oxidem e seja liberado elevados teores de gases tóxicos durante a reação. Zeólita NaA foi misturada com enxofre e carbonato de sódio em diferentes proporções com o objetivo de verificar a influência dessa variação na cor e na tonalidade dos pigmentos. Após calcinação a 500 °C por 5 horas os produtos foram caracterizados por DRX, FRX e Raman, além da classificação visual por cor e tonalidade por meio de fotografias. O resultado foi produtos com coloração que variaram do azul ao verde com diferentes tonalidades, ambas influenciadas pela quantidade de aditivos, pela taxa de resfriamento após calcinação e pela granulometria. Assim, pode-se dizer que quantidades diferentes dos mesmos aditivos na mesma matriz zeolítica proporcionam aumento de intensidade da cor, que a taxa de resfriamento após calcinação e granulometria da matriz zeolítica provoca mudança da cor. A partir de DRX foi observado que a estrutura da zeólita NaA não é transformada para o tipo sodalita, como normalmente observado na literatura. Por espectroscopia Raman foram identificadas as espécies de enxofre responsáveis pela coloração no pigmento zeolítico, sendo: S₆ ^2- o responsável pela cor amarela e o S₃^- pela cor azul, e que a mistura dos dois resultou na cor verde, que predominou nesse trabalho. Por fim, o aproveitamento de rejeito de caulim na produção de pigmentos zeolíticos parece ser uma boa proposta de produção sustentável.

Fratura precoce da porcelana em restaurações com infra-estrutura de zircônia: influência de gradientes térmicos no desenvolvimento e magnitude de tensões residuais e transitórias

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência das variáveis térmicas sobre os espaçamentos dendríticos terciários durante a solidificação direcional horizontal da liga Al-6%Cu

A liga Al-6%Cu foi solidificada direcionalmente sob condições transitórias de extração de calor e microestruturas dendríticas, variáveis térmicas de solidificação, ou seja, velocidade de deslocamento da isoterma líquidus (V_L), taxa de resfriamento (T_R) e gradiente de temperatura à frente da isoterma liquidus (G_L) foram caracterizadas, determinadas experimentalmente e correlacionadas com os espaçamentos dentríticos terciários (λ₃). Para tanto, foi projetado, construído e aferido um dispositivo de solidificação direcional horizontal. Os resultados encontrados mostram que leis de potência -1,1 e -0,55 caracterizam a variação dos espaçamentos terciários com a velocidade de deslocamento da isoterma liquidus (V_L) e a taxa de resfriamento (T_R), respectivamente. Finalmente, é realizado um estudo comparativo entre os resultados obtidos neste trabalho e aqueles publicados na literatura para ligas Al-Cu solidificadas direcionalmente sob condições transientes de fluxo de calor nos sistemas verticais ascendente e descendente.

Caracterização mecânica de uma porcelana de aplicação convencional e uma prensada para recobrimento de infraestruturas de zircônia e o efeito do método de resfriamento na resistência à flexão biaxial do conjunto zircônia/porcelana

Pós-graduação em Reabilitação Oral - FOAR

Ti-Mo alloys employed as biomaterials: Effects of composition and aging heat treatment on microstructure and mechanical behavior

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tratamento de modificação de eutético da liga AA356

Alloy Al-7%Si-0,3Mg (AA356), having an excellent combination of properties such as low solidification shrinkage and good fluidity, good weldability, high wear resistance, high strength to weight particularly in the automotive and aerospace engineering. The refinement of the structure aluminum silicon eutectic alloy is a fairly common practice in the casting, through the treatment knows as modification. You can get the modification for the addition of chemicals and rare earths, these have the ability to modify the structure of the eutectic, but only sodium and strontium produce a strong action modifier when used in low concentrations. The modifying effect of silicon grain turns into a fibrous form branched and enveloped by the metal matrix in the form of a composite structure that has the highest limit of tensile strength, ductility and machinability. This work will be obtained AA356 alloy ingots using two different types of molds: metal mold and sand mold. Macrographs will be made in ingots obtained for observation of the macrostructures obtained in both types of ingots. Will be sampled at strategic locations of the ingots to correlate microstructure and cooling rate. The results showed that the material of the ingot has a strong influence on the resulting micro-andmacrostructure

Processo de fabricação de tarugos pelo método HotTop de ligas de alumínio da série 6XXX e as não conformidades desse processamento

The goal of this work is to report some problems that occur in the in the production of aluminum billets (series 6XXX) produced by the hot top process in the Alcoa aluminum Inc. The aluminum fabrication process is described from its first stage, since the mining until the reduction, smelting and treatment of the metal. One of the plant’s final product, are billets for clients that produce profiles by extrusion. The product’s final quality highly depends on the whole production process. Therefore it’s necessary to use good practices in the treatment of the metal, follow up its fabrication and control its thermal treatment, in order to meet the required standards to satisfy the clients. The billet’s production method and its variables will be detailed through temperature and casting speed, cone of water flow, cooling rate, duration of thermal treatment, degassing and metal “in line “filtering, in other words when it’s still found in its liquid state. The non-conformities of the process were studied by metallographic analysis, both macrostutural and microstructural that will be described and discussed in this work

Refrigeração de sêmen de garanhões

Because the routine use of frozen semen has some limitation that don´t permit its use in a large-scale, it is necessary to use the cooled semen. The equine cooled semen is normally used to enable that a genetic material with high quality be spread over long distances. When it reaches the temperature of refrigeration, the sperm metabolic activity decreases and the free radicals formation minimize. These ones cause irreversible damages to the sperm cells and, so, its lower formation is very advantageous. However, when we manipulate the semen using conservation techniques, like refrigeration, it is necessary to be aware about the sperm characteristics and fragilities, because, if performed erroneously, this technique can be harmful to the sperm function as well as to the time of sperm capacitation and acrosome reaction. It is necessary that cooling rate is slow and that the time and the storage temperature of the sperm obey the ranges that are already established. Moreover, we should make use of diluents and obtain the ideal sperm dilution, so that its use can be optimized. It´s also important to emphasize that to obtain good fertility rates, the semen, after processed (collected and diluted) must be conditioned in recipients specially developed for this purpose

Análise da curva de resfriamento e refino de grão da liga de alumínio AA 356

The macrostructure of an alloy solidification in the raw state is of utmost importance due to its influence on mechanical properties. A structure showing columnar grains is generally undesirable in most applications of cast products and grain refining aims to suppress the formation of these grains and get a fine-grained equiaxed structure that improves the supply of liquid metal and the mechanical properties, as yield strength and tensile strength limit, as well as the tendency of formation of hot cracks. The type and size of grains formed are determined by chemical composition, cooling rate and the use of inoculum for grain refining. Titanium and boron are the major refiners in the aluminum industry and can be added to the molten metal in the form of alloys such as Al-Ti, Al-Ti-B or Al-B. In this paper we will discuss the information obtained from cooling curves and first derivative of the cooling curve to obtain the thermal parameters that influence the process of grain refining alloy AA 356.0

Avaliação da influência da taxa de resfriamento posterior ao tratamento térmico nas propriedades mecânicas do aço API 5L X70

In this work a study about the mechanical properties of the API 5L X70 steel, with or without heat treating, has been made, with the intetion of assess the influence of cooling after the austenitization heat treating by air cooling (normalizing) and a rapid cooling with oil (tempering). This steel is known by high strength and ductility values and it is commonly used in the manufacture of oil pipes. The growing energy demand encouraged the study and manufacture of this material. Although this microalloyed dispense subsequent heat treatings, it was proven that its implementation is very advantageous for this type of application, improving hardness and plastic stability. It was also assessed that the faster the cooling rate is, the better will be these properties

Análise macro e micrográfica da liga AA-356 conforme a taxa de resfriamento

The present work aims to study the characteristics of the alloy Al - 7 % Si - 0 , 3Mg ( AA356 ) , more specifically characterize the macrostructure and microstructure and mechanical properties of the alloy ingots AA356 obtained in metal molds and sand molds for power studying the structures through the difference of cooling rates . This alloy is explained by the fact of referring league has excellent combination of properties such as low solidification shrinkage and good fluidity, good weldability , high wear resistance , high strength to weight ratio, has wide application in general engineering , and particularly in the automotive and aerospace engineering . In this work we will verify this difference in properties through two different cooling rates . We monitor the solid solidification temperatures by thermocouples building with them the cooling curve as a tool that will aid us to evaluate the effectiveness of the grain refining because it achieved with some important properties of the alloy as the latent heat of solidification fraction the liquid and solid temperatures, the total solidification time, and identify the presence of inoculants for grain refinement. Thermal analysis will be supported by the study of graphic software “Origin “will be achieved where the cooling curve and its first derivative that is the cooling rate. Made thermal analysis, analysis will be made in macrographs ingots obtained for observation of macrostructures obtained in both types of ingots and also analysis of micrographs where sampling will occur in strategic positions ingots to correlate with the microstructure. Finally will be collecting data from Brinell hardness of ingots and so then correlating the properties of their respective ingots with cooling rate. We found that obtained with cast metal ingots showed superior properties to the ingots obtained with sand mold

Caracterização estrutural da Liga Al-1% Si

The aim of this study is to characterize the macrostructure and microstructure of Al - 1%Si alloy obtained in sand and metallic molds. Aluminium has good mechanical properties, but adding silicon, even in small quantities, can change the microstructure and improves mechanical behavior. Workpieces were castings in metallic and sand molds and one can see a difference in their cooling curve, macroscopic and microscopic structures. The sand mold casting has lower cooling rate and so its grains are larger. Due to the lower concentration of grain boundary, the hardness is lower compared to that found in metallic molds, which has smaller grains and a higher hardness. Therefore, it can be concluded that the cooling rate and alloying elements affect the final microstructure of the workpiece

Análise metalográfica do titânio puro submetido à soldagem laser Nd: YAG e TIG

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effects of polyethylene film wrap on cooler shrink and the microbial status of beef carcasses

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)