Concrete Pavement Mixture Design and Analysis (MDA): Factors Influencing Drying Shrinkage, TPF-5(205), 2014

This literature review focuses on factors influencing drying shrinkage of concrete. Although the factors are normally interrelated, they can be categorized into three groups: paste quantity, paste quality, and other factors.

Aggregation under a forced convective flow

Morphological transitions are analyzed for a radial multiparticle diffusion-limited aggregation process grown under a convective drift. The introduction of a tangential flow changes the morphology of the diffusion-limited structure, into multiarm structures, inclined opposite to the flow, whose limit consists of single arms, when decreasing density. The case of shear flow is also considered. The anisotropy of the patterns is characterized in terms of a tangential correlation function based analysis. Comparison between the simulation results and preliminary experimental results has been done.

Drying of Ink in Inkjet Printing

Tämän diplomityön tavoitteena oli saada perustietoa tekijöistä, jotka vaikuttavat musteen kuivumiseen erilaisilla paperipinnoilla inkjet tulostuksessa. Tavoitteena oli saada tietoa erilaisista musteista, joita käytetään yleisimmissä inkjet tulostustekniikoissa, miten paperit vaikuttavat musteen kuivumiseen ja minkälaisia menetelmiä on olemassa musteen kuivumistekijöiden määrittämiseen. Lisäksi tarkoituksena oli varmistaa, voidaanko inkjetmusteiden absorptioajan määrittämiseen käytettävää DIGAT-laitetta käyttää määrittämään ja ennustamaan erilaisten musteiden kuivumista erilaisilla paperipinnoilla sekä etsiä korrelaatioita musteen absorptioajan ja teknisten paperiominaisuuksien sekä inkjet tulostuksen laadun välillä. Kirjallisuusosassa tarkasteltiin erilaisia inkjet tulostusmenetelmiä, niissä käytettäviä musteita ja musteiden koostumuksia. Tutkittiin myös paperin ja musteen välisiä vuorovaikutuksia sekä inkjet tulostuksen laatua. Kokeellisessa osassa tutkittiin musteenabsorboitumista paperiin DIGAT-laitteen avulla. kuudella eri musteella. Paperinäytteistä määritettiin teknisiä paperiominaisuuksia sekä ominaisuuksia, jotka liittyvät inkjet tulostuksen laatuun. Inkjet tulostuksen laatua tarkasteltiin tulostamalla testikuva kolmella eri tulostimella, jotka olivat Canon Bubble Jet i950, HP DeskJet Cxi970 ja Epson Stylus C46. Havaittiin, että DIGAT-laite ei sovellu määrittämään musteen absorptioaikoja kiiltäville näytteille.Tässä tutkimuksessa näyte, jonka kiilto oli 65 %, oli liian kiiltävä mitattavaksi DIGAT-laitteella. Lisäksi absorptiomäärityksissä havaittiin, että erilaiset musteet asettuvat erilailla paperin pintaan ja että pigmenttipohjaisella musteella asettumisaika oli kaikista pisin. Musteiden absorptioajat olivat nopeimpia erikoisinkjetpaperilla ja hitaimpia päällystetyillä, tiiviillä papereilla. Musteen absorptioajan ja teknisten paperiominaisuuksien ja inkjet tulostuksen laadun välisiä korrelaatioita oli vaikea havaita. Voidaan sanoa, että tulokset olivat muste- ja printterikohtaisia. Havaittiin vain muutamia teknisiä paperiominaisuuksia, jotka korreloivat hyvin musteen absorboitumisen kanssa. Nämäolivat Gurley-Hill huokoisuus, paperin tuhka- sekä kalsiumkarbonaattipitoisuus ja K&N värinabsorptio. Myöskään inkjet tulostuksen laadun ja musteen absorption välisiä korrelaatioita ei löytynyt kuin muutama; densiteetti, mottling sekä bleeding. Tämän tutkimuksen perusteella voidaan todeta DIGAT-laitteen soveltuvan hyvin kuvaamaan inkjet tulostuksen laatuominaisuuksista densiteettia, mottlingia sekä bleedingiä. DIGAT-laitetta voidaan siis käyttää avuksi ennustettaessa kuivumisaikaa ja sen vaikutusta edellä mainittuihin ominaisuuksiin. Läpipainatusominaisuuksia DIGAT-laitteen avulla ei voida tutkia, sillä ne ovat enemmän riippuvaisia paperin neliömassasta, paksuudesta ja huokoisuudesta kuinmusteen absorptioajasta. Teknisistä paperiominaisuuksista Gurley-Hill huokoisuus, paperin tuhka-sekä CaCO3-pitoisuus ja K&N värinabsorptio kuvaavat hyvin musteen imeytymisaikaa paperiin, kun taas ominaisuudet Cobb, HST ja polaari- sekädispersiokomponentit eivät kuvaa. Näyttää siltä, että testikuva, joka on tällä hetkellä käytössä UPM Tutkimus-keskuksessa, ei sovellu suurtehotulostuksen laadun tarkkailuun. Testikuva toimii hyvin pöytätulostimilla ja perinteisillä kopiopapereilla ja inkjetpapereilla, jotka on tarkoitettu tulostettaviksi hitaasti. Tulostusnopeuden ja musteen kuivumisnopeuden välisiä ilmiöitä seei tuo esille, joten se ei sovellu kuvaamaan suurtehotulostusta.

Ash Particle Erosion on Steam Boiler Convective Section

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. Anew, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosionwear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling andcirculating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can beused to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an inline tube bank with six tube rows, and a staggered tube bank with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss, diameter loss and wall thickness loss measurements of the test sleeves were taken. Erosion wear as a function of flow conditions, tube material and tube construction was analyzed by single-variable linear regression analysis. In developing the erosion wear calculation equations, multi-variable linear regression analysis was used. In the staggered tube bank, erosion wear had a maximum value in a tube row 2 and a local maximum in row 5. In rows 3, 4 and 6, the erosion rate was low. On the other hand, in the in-line tube bank the minimum erosion rate occurred in tube row 2 and in further rows the erosion had an increasing value, so that in a six row tube bank, the maximum value occurred in row 6.

Characterization and drying of caja bagasse (Spondias mombin L.) in a tray dryer using a factorial planning

The caja (Spondias mombin L.) is used in the manufacture of ice-cream, jams, pulps, beverages being also consumed in natura. One of the most important procedures in food conservation is drying, considering that most fresh fruits contain approximately 80% of water. Food drying is used to obtain two basic aspects: (1) the economic factor; in the shipping and handling of the product; (2) at the manipulation; once dried and grinded, the material is rehydrated, at desirable levels, to formulate a new product as in ice cream, jams, yoghurts and drinks and may also be added to pasta, biscuits and other industrialized products. The aim of this study was to investigate the kinetics of caja bagasse drying in a fixed-bed tray dryer, using central composite factorial planning. The following factors were evaluated: temperature (55, 65 and 75 ºC), dryer inlet air velocity (3.2, 4.6 and 6.0 m.s-1) and cake thickness (0.8, 1.2 and 1.6 cm) where the response of the considered variable was caja bagasse moisture content (b.s.) and the results showed that the main effects and their interactions were significant at a 95% confidence level being the best condition obtained at temperature of 75 ºC, velocity of 6.0 m.s-1 and cake thickness of 0.8 cm.

Characteristics of 2D convective structures in Catalonia (NE Spain): an analysis using radar data and GIS

Flood simulation studies use spatial-temporal rainfall data input into distributed hydrological models. A correct description of rainfall in space and in time contributes to improvements on hydrological modelling and design. This work is focused on the analysis of 2-D convective structures (rain cells), whose contribution is especially significant in most flood events. The objective of this paper is to provide statistical descriptors and distribution functions for convective structure characteristics of precipitation systems producing floods in Catalonia (NE Spain). To achieve this purpose heavy rainfall events recorded between 1996 and 2000 have been analysed. By means of weather radar, and applying 2-D radar algorithms a distinction between convective and stratiform precipitation is made. These data are introduced and analyzed with a GIS. In a first step different groups of connected pixels with convective precipitation are identified. Only convective structures with an area greater than 32 km2 are selected. Then, geometric characteristics (area, perimeter, orientation and dimensions of the ellipse), and rainfall statistics (maximum, mean, minimum, range, standard deviation, and sum) of these structures are obtained and stored in a database. Finally, descriptive statistics for selected characteristics are calculated and statistical distributions are fitted to the observed frequency distributions. Statistical analyses reveal that the Generalized Pareto distribution for the area and the Generalized Extreme Value distribution for the perimeter, dimensions, orientation and mean areal precipitation are the statistical distributions that best fit the observed ones of these parameters. The statistical descriptors and the probability distribution functions obtained are of direct use as an input in spatial rainfall generators.

Nutritional potential of green banana flour obtained by drying in spouted bed

This study evaluated the chemical composition of peeled and unpeeled green banana Cavendish (AAA) flour obtained by drying in spouted bed, aiming at adding nutritional value to food products. The bananas were sliced and crushed to obtain a paste and fed to the spouted bed dryer (12 cm height and T = 80 ºC) in order to obtain flour. The flours obtained were subjected to analysis of moisture, protein, ash, carbohydrates, total starch, resistant starch, fiber. The green banana flours, mainly unpeeled, are good sources of fiber and resistant starch with an average of 21.91g/100g and 68.02g/100g respectively. The protein content was found in an average of 4.76g/100g, being classified as a low biological value protein with lysine as the first limiting amino acid. The results showed that unpeeled green banana flour obtained by spouted bed drying can be a valuable tool to add nutritional value to products in order to increase their non-digestible fraction.

Reuse of information for selection of methods and operating conditions for drying of pharmaceutical materials

Drying is a major step in the manufacturing process in pharmaceutical industries, and the selection of dryer and operating conditions are sometimes a bottleneck. In spite of difficulties, the bottlenecks are taken care of with utmost care due to good manufacturing practices (GMP) and industries' image in the global market. The purpose of this work is to research the use of existing knowledge for the selection of dryer and its operating conditions for drying of pharmaceutical materials with the help of methods like case-based reasoning and decision trees to reduce time and expenditure for research. The work consisted of two major parts as follows: Literature survey on the theories of spray dying, case-based reasoning and decision trees; working part includes data acquisition and testing of the models based on existing and upgraded data. Testing resulted in a combination of two models, case-based reasoning and decision trees, leading to more specific results when compared to conventional methods.

The summer North Atlantic Oscillation in CMIP3 models and related uncertainties in projected summer drying in Europe

This paper discusses uncertainties in model projections of summer drying in the Euro-Mediterranean region related to errors and uncertainties in the simulation of the summer NAO (SNAO). The SNAO is the leading mode of summer SLP variability in the North Atlantic/European sector and modulates precipitation not only in the vicinity of the SLP dipole (northwest Europe) but also in the Mediterranean region. An analysis of CMIP3 models is conducted to determine the extent to which models reproduce the signature of the SNAO and its impact on precipitation and to assess the role of the SNAO in the projected precipitation reductions. Most models correctly simulate the spatial pattern of the SNAO and the dry anomalies in northwest Europe that accompany the positive phase. The models also capture the concurrent wet conditions in the Mediterranean, but the amplitude of this signal is too weak, especially in the east. This error is related to the poor simulation of the upper-level circulation response to a positive SNAO, namely the observed trough over the Balkans that creates potential instability and favors precipitation. The SNAO is generally projected to trend upwards in CMIP3 models, leading to a consistent signal of precipitation reduction in NW Europe, but the intensity of the trend varies greatly across models, resulting in large uncertainties in the magnitude of the projected drying. In the Mediterranean, because the simulated influence of the SNAO is too weak, no precipitation increase occurs even in the presence of a strong SNAO trend, reducing confidence in these projections.

The effect of microfibrillated cellulose addition on drying shrinkage and dimensional stability of wood-free paper

Microfibrillated cellulose (MFC) is known to enhance strength properties of paper. Improved strength usually means increased bonding which is strongly connected to dimensional instability of paper. Dimensional instability is due to changes in moisture content of paper; when paper is moistened it expands and when dried, it shrinks. Hygroexpansion is linked to end-use problems and excessive drying shrinkage consumes strength potential. Effective use of materials requires controlling of these phenomena. There isn’t yet data concerning dimensional stability of papers containing MFC which restricts wider use of MFC. Main objective of the work was to evaluate dimensional stability of wood-free paper containing different amounts of MFC. Sheets were dried with different methods to see how drying strains effected on drying shrinkage and hygroexpansion. Also tensile strength was measured to find out the effect of MFC. Results were compared to sheets containing kraft fines and in some test points cationic starch was used alongside with MFC. MFC increased the dimensional instability of freely dried sheets. As the amounts of MFC increased the effects on dimensional stability became more severe. However the fineness of MFC didn’t play any important role. Both hygroexpansion and drying shrinkage were decreased with cationic starch addition. Prevention of drying shrinkage over powered the effects of additives on hygroexpansion. Tensile strength improved up till 7 % addition amount which could be set as the upper limit of MFC addition when paper preparation and tensile strength are concerned.

Microencapsulação do agente quelante sulfoxina em microesferas de quitosana preparadas por spray drying como novo adsorvente para íons metálicos

In this work, a new adsorbent was prepared by microencapsulation of sulfoxine into chitosan microspheres by the spray drying technique. The new adsorbent was characterized by Raman spectroscopy, scanning electron microscopy and microanalysis of energy dispersive X-rays. The Cu(II) adsorption was studied as a function of pH, time and concentration. The optimum pH was found to be 6.0. The kinetic and equilibrium data showed that the adsorption process followed the pseudo second-order kinetic model and the Langmuir isotherm model over the entire concentration range. An increase of 8.0% in the maximum adsorption capacity of the adsorbent (53.8 mg g-1) was observed as compared to chitosan glutaraldehyde cross-linked microspheres.

Imobilização da lacase em micropartículas de quitosana obtidas por spray drying e usadas na construção de biossensores

Biosensors based on laccase immobilized on microparticles of chitosan crosslinked with tripolyphosphate (biosensor I) and glyoxal (biosensor II) obtained by spray drying for the determinations of rutin in pharmaceutical formulations were developed. Under optimized operational conditions (pH 4.0, frequency of 30 Hz, pulse amplitude of 40 mV and scan increment of 2.0 mV) two analytical curves were obtained for both biosensors showing a detection limit of 6.2x10-8 mol L-1 for biosensor (I) and 2.0x10-8 mol L-1 for biosensor (II). The recovery of rutin from pharmaceutical sample ranged from 90.7 to 105.0% and the lifetime of these biosensors were 4 months (at least 400 determinations).

An expeditious and consistent procedure for tetrahydrofuran (THF) drying and deoxygenation by the still apparatus

Despite the availability of alternative methods for drying tetrahydrofuran (THF), the use of the still apparatus, wherein a THF solution containing Na-bezophenone ketyl is heated to reflux, remains widespread. We herein propose a set of procedures to solve the problems usually faced in applying this drying technique. Moreover, a discussion is made on the chemical knowledge underlying such procedures. Safety and economy issues concerned with the operation of the THF still apparatus are also discussed.

Evaluation of chitosan microparticles containing curcumin and crosslinked with sodium tripolyphosphate produced by spray drying

The aim of this study was to encapsulate curcumin into chitosan, using sodium tripolyphosphate (TPP) as an ionic crosslinker by the spray drying method. The influence of TPP on the properties of the final product, such as solubility, morphology, loading efficiency, thermal behavior, swelling degree and release profiles, was evaluated. The microparticles had a spherical morphology (0.5-20 µm) with no apparent porosity or cracks. Results indicated the formation of a polymeric network, which ensures effective protection for curcumin. Controlled-release studies were carried out at pH 1.2 and 6.8, to observe the influence of pH on curcumin release while the mechanism was analyzed using the Korsmeyer-Peppas equation.