Caracterização reológica de pastas de cimento portland de alta resistência contendo diferentes tipos de polímeros superabsorventes pela técnica de reometria rotacional

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Développement des bétons autoplaçants à faible teneur en poudre, Éco-BAP: formulation et performance

Abstract : Although concrete is a relatively green material, the astronomical volume of concrete produced worldwide annually places the concrete construction sector among the noticeable contributors to the global warming. The most polluting constituent of concrete is cement due to its production process which releases, on average, 0.83 kg CO[subscript 2] per kg of cement. Self-consolidating concrete (SCC), a type of concrete that can fill in the formwork without external vibration, is a technology that can offer a solution to the sustainability issues of concrete industry. However, all of the workability requirements of SCC originate from a higher powder content (compared to conventional concrete) which can increase both the cost of construction and the environmental impact of SCC for some applications. Ecological SCC, Eco-SCC, is a recent development combing the advantages of SCC and a significantly lower powder content. The maximum powder content of this concrete, intended for building and commercial construction, is limited to 315 kg/m[superscript 3]. Nevertheless, designing Eco-SCC can be challenging since a delicate balance between different ingredients of this concrete is required to secure a satisfactory mixture. In this Ph.D. program, the principal objective is to develop a systematic design method to produce Eco-SCC. Since the particle lattice effect (PLE) is a key parameter to design stable Eco-SCC mixtures and is not well understood, in the first phase of this research, this phenomenon is studied. The focus in this phase is on the effect of particle-size distribution (PSD) on the PLE and stability of model mixtures as well as SCC. In the second phase, the design protocol is developed, and the properties of obtained Eco-SCC mixtures in both fresh and hardened states are evaluated. Since the assessment of robustness is crucial for successful production of concrete on large-scale, in the final phase of this work, the robustness of one the best-performing mixtures of Phase II is examined. It was found that increasing the volume fraction of a stable size-class results in an increase in the stability of that class, which in turn contributes to a higher PLE of the granular skeleton and better stability of the system. It was shown that a continuous PSD in which the volume fraction of each size class is larger than the consecutive coarser class can increase the PLE. Using such PSD was shown to allow for a substantial increase in the fluidity of SCC mixture without compromising the segregation resistance. An index to predict the segregation potential of a suspension of particles in a yield stress fluid was proposed. In the second phase of the dissertation, a five-step design method for Eco-SCC was established. The design protocol started with the determination of powder and water contents followed by the optimization of sand and coarse aggregate volume fractions according to an ideal PSD model (Funk and Dinger). The powder composition was optimized in the third step to minimize the water demand while securing adequate performance in the hardened state. The superplasticizer (SP) content of the mixtures was determined in next step. The last step dealt with the assessment of the global warming potential of the formulated Eco-SCC mixtures. The optimized Eco-SCC mixtures met all the requirements of self-consolidation in the fresh state. The 28-day compressive strength of such mixtures complied with the target range of 25 to 35 MPa. In addition, the mixtures showed sufficient performance in terms of drying shrinkage, electrical resistivity, and frost durability for the intended applications. The eco-performance of the developed mixtures was satisfactory as well. It was demonstrated in the last phase that the robustness of Eco-SCC is generally good with regards to water content variations and coarse aggregate characteristics alterations. Special attention must be paid to the dosage of SP during batching.

Influence of macroscopic residual stress fields on fatigue crack growth measurement in SiC particulate reinforced 8090 aluminium alloy

The effect of residual stresses, induced by cold water quenching, on the morphology of fatigue crack fronts has been investigated in a powder metallurgy 8090 aluminium alloy, with and without reinforcement in the form of 20 wt-%SiC particles. Residual stress measurements reveal that the surface compressive stresses developed in these materials are significantly greater than in conventional metallurgy ingot 8090, because surface yielding occurs on quenching. The yield stresses of the powder route materials are greater than those of ingot produced 8090 and hence greater surface stresses can be maintained. In fatigue, severe crack front bowing is observed in the powder formed materials as a result of the reduction of the R ratio (minimum load/maximum load) by the compressive residual stresses at the sides of the specimen, causing premature crack closure and hence reducing the local driving force for fatigue crack growth ΔKeff. This distortion of the crack fronts introduces large errors into measurements of crack growth rate and threshold values of ΔK.

Micro-mechanical approximation to the stress field around an inclined fiber of FRCC

Matrix spalling or crushing is one of the important mechanisms of fiber-matrix interaction of fiber reinforced cementitious composites (FRCC). The fiber pullout mechanisms have been extensively studied for an aligned fiber but matrix failure is rarely investigated since it is thought not to be a major affect. However, for an inclined fiber, the matrix failure should not be neglected. Due to the complex process of matrix spalling, experimental investigation and analytical study of this mechanism are rarely found in literature. In this paper, it is assumed that the load transfer is concentrated within the short length of the inclined fiber from the exit point towards anchored end and follows the exponential law. The Mindlin formulation is employed to calculate the 3D stress field. The simulation gives much information about this field. The 3D approximation of the stress state around an inclined fiber helps to qualitatively understand the mechanism of matrix failure. Finally, a spalling criterion is proposed by which matrix spalling occurs only when the stress in a certain volume, rather than the stress at a small point, exceeds the material strength. This implies some local stress redistribution after first yield. The stress redistribution results in more energy input and higher load bearing capacity of the matrix. In accordance with this hypothesis, the evolution of matrix spalling is demonstrated. The accurate prediction of matrix spalling needs the careful determination of the parameters in this model. This is the work of further study. (C) 2002 Elsevier Science Ltd. All rights reserved.

A yield architecture framework to explain adaptation of pearl millet to environmental stress

Functional knowledge of the physiological basis of crop adaptation to stress is a prerequisite for exploiting specific adaptation to stress environments in breeding programs. This paper presents an analysis of yield components for pearl millet, to explain the specific adaptation of local landraces to stress environments in Rajasthan, India. Six genotypes, ranging from high-tillering traditional landraces to low-tillering open-pollinated modern cultivars, were grown in 20 experiments, covering a range of nonstress and drought stress patterns. In each experiment, yield components (particle number, grain number, 100 grain mass) were measured separately for main shoots, basal tillers, and nodal tillers. Under optimum conditions, landraces had a significantly lower grain yield than the cultivars, but no significant differences were observed at yield levels around 1 ton ha(-1). This genotype x environment interaction for grain yield was due to a difference in yield strategy, where landraces aimed at minimising the risk of a crop failure under stress conditions, and modem cultivars aimed at maximising yield potential under optimum conditions. A key aspect of the adaptation of landraces was the small size of the main shoot panicle, as it minimised (1) the loss of productive tillers during stem elongation; (2) the delay in anthesis if mid-season drought occurs; and (3) the reduction in panicle productivity of the basal tillers under stress. In addition, a low investment in structural panicle weight, relative to vegetative crop growth rate, promoted the production of nodal tillers, providing a mechanism to compensate for reduced basal tiller productivity if stress occurred around anthesis. A low maximum 100 grain mass also ensured individual grain mass was little affected by environmental conditions. The strategy of the high-tillering landraces carries a yield penalty under optimum conditions, but is expected to minimise the risk of a crop failure, particularly if mid-season drought stress occurs. The yield architecture of low-tillering varieties, by contrast, will be suited to end-of-season drought stress, provided anthesis is early. Application of the above adaptation mechanisms into a breeding program could enable the identification of plant types that match the prevalent stress patterns in the target environments. (C) 2003 E.J. van Oosterom. Published by Elsevier Science B.V. All rights reserved.

Evaluation of the performance of steel fibre reinforced self-compacting concrete in elevated slab systems; from the material to the structure

Degree of Doctor of Philosophy of Structural/Civil Engineering

Combining ability of maize grain yield under different levels of environmental stress

The objectives of this work were to caracterize the tropical maize germplasm and to compare the combining abilities of maize grain yield under different levels of environmental stress. A diallel was performed among tropical maize cultivars with wide adaptability, whose hybrid combinations were evaluated in two sowing dates, in two years. The significance of the environmental effect emphasized the environmental contrasts. Based on grain yield, the environments were classified as favorable (8,331 kg ha-1), low stress (6,637 kg ha-1), high stress (5,495 kg ha-1), and intense stress (2,443 kg ha-1). None of the genetic effects were significant in favorable and intense stress environments, indicating that there was low germplasm variability under these conditions. In low and high stresses, the specific combining ability effects (SCA) were significant, showing that the nonadditive genetic effects were the most important, and that it is possible to select parent pairs with breeding potential. SCA and grain yield showed significant correlations only between the closer environment pairs like favorable/low stress and high/intense stress. The genetic control of grain yield differed under contrasting stress environments for which maize cultivars with wide adaptability are not adequate.

Insect pollination reduces yield loss following heat stress in faba bean (Vicia faba L.)

Global food security, particularly crop fertilization and yield production, is threatened by heat waves that are projected to increase in frequency and magnitude with climate change. Effects of heat stress on the fertilization of insect-pollinated plants are not well understood, but experiments conducted primarily in self-pollinated crops, such as wheat, show that transfer of fertile pollen may recover yield following stress. We hypothesized that in the partially pollinator-dependent crop, faba bean (Vicia faba L.), insect pollination would elicit similar yield recovery following heat stress. We exposed potted faba bean plants to heat stress for 5 days during floral development and anthesis. Temperature treatments were representative of heat waves projected in the UK for the period 2021-2050 and onwards. Following temperature treatments, plants were distributed in flight cages and either pollinated by domesticated Bombus terrestris colonies or received no insect pollination. Yield loss due to heat stress at 30°C was greater in plants excluded from pollinators (15%) compared to those with bumblebee pollination (2.5%). Thus, the pollinator dependency of faba bean yield was 16% at control temperatures (18 to 26°C) and extreme stress (34°C), but was 53% following intermediate heat stress at 30°C. These findings provide the first evidence that the pollinator dependency of crops can be modified by heat stress, and suggest that insect pollination may become more important in crop production as the probability of heat waves increases.

Effects of Silicon and Drought Stress on Tuber Yield and Leaf Biochemical Characteristics in Potato

Silicon has beneficial effects on many crops, mainly under biotic and abiotic stresses. Silicon can affect biochemical, physiological, and photosynthetic processes and, consequently, alleviates drought stress. However, the effects of Si on potato (Solanum tuberosum L.) plants under drought stress are still unknown. The objective of this study was to evaluate the effect of Si supply on some biochemical characteristics and yield of potato tubers, either exposed or not exposed to drought stress. The experiment was conducted in pots containing 50 dm(3) of a Typic Acrortox soil (33% clay, 4% silt, and 63% sand). The treatments consisted of the absence or presence of Si application (0 and 284.4 mg dm(-3)), through soil amelioration with dolomitic lime and Ca and Mg silicate, and in the absence or presence of water deficit (-0.020 MPa and -0.050 MPa soil water potential, respectively), with eight replications. Silicon application and water deficit resulted in the greatest Si concentration in potato leaves. Proline concentrations increased under lower water availability and higher Si availability in the soil, which indicates that Si may be associated with plant osmotic adjustment. Water deficit and Si application decreased total sugars and soluble proteins concentrations in the leaves. Silicon application reduced stalk lodging and increased mean tuber weight and, consequently, tuber yield, especially in the absence of water stress.

Effect of dietary betaine supplementation on the performance, carcass yield, and intestinal morphometrics of broilers submitted to heat stress

The objective of this study was to evaluate the effect of betaine in methionine- and choline-reduced diets fed to broilers submitted to heat stress. In total, 1,408 male broilers were randomly distributed into eight treatments, according to 2 × 4 (environment x diet) factorial arrangement, with eight replicates of 2 birds each. Birds were reared environmental chambers under controlled temperature (25-26 °C) or cyclic heat-stressing temperature (25-31 °C). The following diets were tested: positive control (PC), formulated to meet broiler nutritional requirements; negative control (NC), with reduced DL-methionine and choline chloride levels; and with two supplementation levels of natural betaine to the negative control diet (NC+NB1 and NC+NB2). Live performance, carcass traits, and intestinal morphometrics were evaluated when broilers were 45 days of age. The results showed that all evaluated parameters were influenced by the interaction between environment and diet, except for breast meat drip loss. The breakdown of the interactions showed that birds fed the PC diet and reared in the controlled environment had greater breast drip loss than those submitted to the cyclic heat-stress environment. Birds submitted to cyclic heat stress and fed the PC diet presented the lowest feed intake. Feed conversion ratio was influenced only by diet. The FCR of broilers fed the NC+NB2 diet was intermediate relative to those fed the PC and NC diets. The addition of betaine in the diet, with 11.18% digestible methionine and 24.73% total choline reductions, did not affect broiler live performance, carcass yield, or intestinal morphometrics.

Effect of the application of jasmonic acid and benzoic acid on grafted watermelons yield under greenhouse conditions in the southeast of Spain for mitigation of stress

One of the main problems of watermelon crops in Sou theast Spain is the thermal difference because of c limatic conditions that appear during the first stages of the crop. The objective of this work was to evaluate the effect of inducing the systemic acq uired resistance (SAR) and the induced systemic resistance (ISR) through the application of jasmonic ac id (JA) and benzoic acid (BA), respectively, to counter the abiotic stress. We assessed two treatments of JA and BA, T1 (500 mg·kg-1 + 500 mg·kg -1 ) and T 2 (2000 mg·kg -1 + 2000 mg·kg -1), as well as a control test using an experimental design of randomized blocks with four replications. The results obtained for kg·m -2, fruits/m², kg/plant and fruits/plant did not show statistically significant differences. However, we obtained statistically sig nificant differences in the average fruit weight co mpared with the control test in the two experiments carried out in 2009 and 2010. The results showed that there was no metabolic cost in the plants when applying the assessed treatments of JA and BA.

Residual stress and the yield strength of steel beams,

Sponsored jointly by the Welding Research Council and the Department of the Navy.

Yield criterion of porous materials subjected to complex stress states

Finite-element simulations are used to obtain many thousands of yield points for porous materials with arbitrary void-volume fractions with spherical voids arranged in simple cubic, body-centred cubic and face-centred cubic three-dimensional arrays. Multi-axial stress states are explored. We show that the data may be fitted by a yield function which is similar to the Gurson-Tvergaard-Needleman (GTN) form, but which also depends on the determinant of the stress tensor, and all additional parameters may be expressed in terms of standard GTN-like parameters. The dependence of these parameters on the void-volume fraction is found. (c) 2006 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.