A retrospective cohort investigation of active range of motion within one week of open reduction and internal fixation of distal radius fractures

Distal radius fractures stabilized by open reduction internal fixation (ORIF) have become increasingly common. There is currently no consensus on the optimal time to commence range of motion (ROM) exercises post-ORIF. A retrospective cohort review was conducted over a five-year period to compare wrist and forearm range of motion outcomes and number of therapy sessions between patients who commenced active ROM exercises within the first seven days and from day eight onward following ORIF of distal radius fractures. One hundred and twenty-one patient cases were identified. Clinical data, active ROM at initial and discharge therapy assessments, fracture type, surgical approaches, and number of therapy sessions attended were recorded. One hundred and seven (88.4%) cases had complete datasets. The early active ROM group (n = 37) commenced ROM a mean (SD) of 4.27 (1.8) days post-ORIF. The comparator group (n = 70) commenced ROM exercises 24.3 (13.6) days post-ORIF. No significant differences were identified between groups in ROM at initial or discharge assessments, or therapy sessions attended. The results from this study indicate that patients who commenced active ROM exercises an average of 24 days after surgery achieved comparable ROM outcomes with similar number of therapy sessions to those who commenced ROM exercises within the first week.

β-Actin—an unsuitable internal control for RT-PCR

Despite reports confirming cell-cycle dependent gene expression and a number of studies describing specific circumstances in which β-actin is also regulated, the mRNA for β-actin remains a widely used housekeeping gene internal control. Utilizing differential reverse transcriptase-polymerase chain reaction (RT-PCR), we report here the dose-dependent inhibition of β-actin by matrigel. This was detected by comparison to the very moderate inhibition of the target gene, membrane type-1 matrix metalloproteinase (MT1-MMP), with results independently confirmed by similar findings on MT1-MMP expression using competitive RT-PCR. Furthermore, RT-PCR of the housekeeping gene 18 Svedberg Units (S) rRNA demonstrated excellent consistency, reproducibility and non-regulation by a matrigel treatment. We conclude that β-actin is highly regulated by matrigel and therefore unsuitable as an internal control in this treatment. Hence, these findings suggest that researchers have a responsibility to ensure that the housekeeping gene of choice is not regulated in their specific application, as such regulation may dramatically affect the accuracy of their results. This study reinforces the necessity for minimally regulated housekeeping genes such as 18S rRNA, and the superiority of competitive templates as internal controls for quantitative applications of RT-PCR.

Predicting the fatigue life of internal fracture fixation plates

Failures of fracture fixation plates, often related to fatigue fractures of the implants, have been reported (Banovetz et al, 1996). While metallurgical defects can usually be excluded, many of these fractures can be explained with the biomechanical situation. This study investigated the biomechanics of two clinical cases, both of which used a 14-hole locking compression plate. In the first case, a titanium plate was used in a rigid configuration with 12 screws resulting in plate breakage after 7 weeks (Sommer et al, 2003). In the second case, a stainless steel plate, which endured the entire healing process, was used in a flexible application with only 6 screws.

Fibrogenic stresses activate different mitogen-activated protein kinase pathways in renal epithelial, endothelial or fibroblast cell populations

Fibrogenic stresses promote progression of renal tubulointerstitial fibrosis, disparately affecting survival, proliferation and trans-differentiation of intrinsic renal cell populations through ill-defined biomolecular pathways. We investigated the effect of fibrogenic stresses on the activation of cell-specific mitogen-activated protein kinase (MAPK) in renal fibroblast, epithelial and endothelial cell populations. The relative outcomes (cell death, proliferation, trans-differentiation) associated with activation or inhibition of extracellular-regulated protein kinase (ERK) or stress activated/c-Jun N terminal kinase (JNK) were analysed in each renal cell population after challenge with oxidative stress (1 mmol/L H2O2), transforming growth factor-beta1 (TGF-beta1, 10 ng/mL) or tumour necrosis factor-alpha (TNF-alpha, 50 ng/mL) over 0-20 h. Apoptosis increased significantly in all cell types after oxidative stress (P < 0.05). In fibroblasts, oxidative stress caused the activation of ERK (pERK) but not JNK (pJNK). Inhibition of ERK by PD98059 supported its role in a fibroblast death pathway. In epithelial and endothelial cells, oxidative stress-induced apoptosis was preceded by early induction of pERK, but its inhibition did not support a pro-apoptotic role. Early ERK activity may be conducive to their survival or promote the trans-differentiation of epithelial cells. In epithelial and endothelial cells, oxidative stress induced pJNK acutely. Pretreatment with SP600125 (JNK inhibitor) verified its pro-apoptotic activity only in epithelial cells. Transforming growth factor-beta1 did not significantly alter mitosis or apoptosis in any of the cell types, nor did it alter MAPK activity. Tumor necrosis factor-alpha caused increased apoptosis with no associated change in MAPK activity. Our results demonstrate renal cell-specific differences in the activation of ERK and JNK following fibrotic insult, which may be useful for targeting excessive fibroblast proliferation in chronic fibrosis.

Vascular remodeling in the internal mammary artery graft and association with in situ endothelin-1 and receptor expression

BACKGROUND: The vasoconstricting peptide endothelin-1 (ET-1) has been associated with atherosclerotic cardiovascular disease, vascular smooth muscle cell (VSMC) growth stimulation, and intimal thickening. ET-1 binds 2 receptor subtypes, endothelin A and B, and the ETA receptor mediates vasoconstriction and VSMC growth. This study aims to quantitatively assess arterial remodeling variables and compare them with changes in ET-1, ETA, and ETB expression in the internal mammary artery (IMA). METHODS AND RESULTS: Specimens from 55 coronary artery disease (CAD) patients (45 men, 10 women; mean age 65 years) and 14 control IMA specimens (from 7 men and 7 women; mean age 45 years) were collected. IMA cross sections were assessed by histochemical and immunohistochemical staining methods to quantify the levels of medionecrosis, fibrosis, VSMC growth, ET-1, ETA, ETB, and macrophage infiltration. The percentage area of medionecrosis in the patients was almost double that in the controls (31.85+/-14.52% versus 17.10+/-9.96%, P=0.0006). Total and type 1 collagen was significantly increased compared with controls (65.8+/-18.3% versus 33.7+/-13.7%, P=0.07, and 14.2+/-10.0% versus 4.8+/-2.8%, P=0.01, respectively). Despite ACE and/or statin therapy, ET-1 expression and cell cycling were significantly elevated in the patient IMAs relative to the controls (46.27+/-18.46 versus 8.56+/-8.42, P=0.0001, and 37.29+/-12.88 versus 11.06+/-8.18, P=0.0001, respectively). ETA and ETB staining was elevated in the patient vessels (46.88+/-11.52% versus 18.58+/-7.65%, P=0.0001, and 42.98+/-7.08% versus 34.73+/-5.20%, P=0.0067, respectively). A mild presence of macrophages was noted in all sections. CONCLUSIONS: Elevated distribution of collagen indicative of fibrosis coupled with increased cell cycling and high levels of ET-1 and ETA expression in the absence of chronic inflammation suggests altered IMA VSMC regulation is fundamental to the remodeling process.

Thinking about internal states, a qualitative investigation into metacognitions in women with eating disorders

Background There is a need for qualitative research to help develop case conceptualisations to guide the development of Metacognitive Therapy interventions for Eating Disorders. Method A qualitative study informed by grounded theory methodology was conducted involving open-ended interviews with 27 women aged 18–55 years, who were seeking or receiving treatment for a diagnosed ED. Results The categories identified in this study appeared to be consistent with a metacognitive model including constructs of a Cognitive Attentional Syndrome and metacognitive beliefs. These categories appear to be transdiagnostic, and the interaction between the categories is proposed to explain the maintenance of EDs. Conclusions The transdiagnostic model proposed may be useful to guide the development of future metacognitive therapy interventions for EDs with the hope that this will lead to improved outcomes for individuals with EDs.

A neutron diffraction investigation of residual stresses in rail ends after severe deformation of rail surfaces

Insulated rail joints (IRJs) are a primary component of the rail track safety and signalling systems. Rails are supported by two fishplates which are fastened by bolts and nuts and, with the support of sleepers and track ballast, form an integrated assembly. IRJ failure can result from progressive defects, the propagation of which is influenced by residual stresses in the rail. Residual stresses change significantly during service due to the complex deformation and damage effects associated with wheel rolling, sliding and impact. IRJ failures can occur when metal flows over the insulated rail gap (typically 6-8 mm width), breaks the electrically isolated section of track and results in malfunction of the track signalling system. In this investigation, residual stress measurements were obtained from rail-ends which had undergone controlled amounts of surface plastic deformation using a full scale wheel-on-track simulation test rig. Results were compared with those obtained from similar investigations performed on rail ends associated with ex-service IRJs. Residual stresses were measured by neutron diffraction at the Australian Nuclear Science and Technology Organisation (ANSTO). Measurements with constant gauge volume 3x3x3 mm3 were carried in the central vertical plane on 5mm thick sliced rail samples cut by an electric discharge machine (EDM). Stress evolution at the rail ends was found to exhibit characteristics similar to those of the ex-service rails, with a compressive zone of 5mm deep that is counterbalanced by a tension zone beneath, extending to a depth of around 15mm. However, in contrast to the ex-service rails, the type of stress distribution in the test-rig deformed samples was apparently different due to the localization of load under the particular test conditions. In the latter, in contrast with clear stress evolution, there was no obvious evolution of d0. Since d0 reflects rather long-term accumulation of crystal lattice damage and microstructural changes due to service load, the loading history of the test rig samples has not reached the same level as the ex-service rails. It is concluded that the wheel-on-rail simulation rig provides the potential capability for testing the wheel-rail rolling contact conditions in rails, rail ends and insulated rail joints.

Internal audit involvement in enterprise risk management

Purpose The paper examines the impact of internal auditors’ involvement in Enterprise Risk Management (ERM) on perceptions of their willingness to report a breakdown in risk procedures and whether a strong relationship with the audit committee affects such willingness to report. The study also investigates the use of ERM and the role of internal audit in ERM in Australian private and public sector entities. Design/methodology/approach The study uses an experimental design, manipulating (i) the internal auditor’s involvement in ERM and (ii) the strength of the relationship between internal audit and the audit committee. Participants are 117 certified internal auditors. The study also gathers descriptive data on the use of ERM. Findings The study indicates that a high involvement in ERM impacts the perceptions of internal auditors’ willingness to report a breakdown in risk procedures to the audit committee. However, a strong relationship with the audit committee does not appear to affect their perceived willingness to report. The study also finds that the majority of organisations have recently adopted ERM. Internal auditors are involved in ERM assurance activities but some also engage in activities that could compromise objectivity.

Optimising employee engagement with internal communication : a social exchange perspective

Drawing on principles of social exchange this thesis employs mediated regression to investigate the relationship between internal communication and employee engagement in the Australian workforce. Findings suggest organisations and supervisors should focus internal communication efforts toward building greater perceptions of support and stronger identification among employees in order to foster optimal engagement. This research contributes to public relations and management scholarship through understanding how perceived support and identification act as mediating mechanisms in the relationship between internal communication and employee engagement at the organisational and supervisory level.

Optimizing employee engagement with internal communication : a social exchange perspective

Employee engagement is linked to higher productivity, lower attrition, and improved organizational reputations resulting in increased focus and resourcing by managers to foster an engaged workforce. While drivers of employee engagement have been identified as perceived support, job characteristics, and value congruence, internal communication is theoretically suggested to be a key influence in both the process and maintenance of employee engagement efforts. However, understanding the mechanisms by which internal communication influences employee engagement has emerged as a key question in the literature. The purpose of this research is to investigate whether social factors, namely perceived support and identification, play a mediating role in the relationship between internal communication and engagement. To test the theoretical model, data are collected from 200 non-executive employees using an online self-administered survey. The study applies linear and mediated regression to the model and finds that organizations and supervisors should focus internal communication efforts toward building greater perceptions of support and stronger identification among employees in order to foster optimal levels of engagement.

Discussion on full-scale internal pressure measurements

The wind loading on most structural elements is made up of both an external and internal pressure. Internal pressures are also important for the design of naturally ventilated buildings. The internal pressure is the interaction between the external pressure propagating through the building envelope and any internal plant causing building pressurization. Although the external pressure field can be well defined through a series of wind tunnel tests, modeling complexities makes accurate prediction of the internal pressure difficult. For commercial testing for the determination of design cladding pressures, an internal pressure coefficient is generally assumed from wind loading standards. Several theories regarding the propagation of internal pressures through single and multiple dominant openings have been proposed for small and large flexible buildings (Harris (1990), Holmes, (1979), Liu & Saathoff (1981 ), Vickery (1986, 1994), Vickery & Bloxham (1992), Vickery & Georgiou (1991))...

Model for internal porosity development of different shaped foods

Three particular geometrical shapes of foods were prepared from food materials. Cuboidal (aspect ratio = 1:1, 2:1, 3:1) , cylindrical (length: dameter = 1:1, 2:1, 3:1) and spheres were selected from potato, beans and peas respectively. Internal porosity was determined from solid density (theoretical)and particle density (experimental) during fluidised bed drying at different moisture contents. Solid density was calculated using formulae (conservation of mass and volume) already published in the literature by previous researchers. Determined porosity values were correlated with moisture ratio for different geometrical shapes.

Generation of uniform plasmas by crossed internal oscillating current sheets : key concepts and experimental verification

The results of comprehensive experimental studies of the operation, stability, and plasma parameters of the low-frequency (0.46 MHz) inductively coupled plasmas sustained by the internal oscillating rf current are reported. The rf plasma is generated by using a custom-designed configuration of the internal rf coil that comprises two perpendicular sets of eight currents in each direction. Various diagnostic tools, such as magnetic probes, optical emission spectroscopy, and an rf-compensated Langmuir probe were used to investigate the electromagnetic, optical, and global properties of the argon plasma in wide ranges of the applied rf power and gas feedstock pressure. It is found that the uniformity of the electromagnetic field inside the plasma reactor is improved as compared to the conventional sources of inductively coupled plasmas with the external flat coil configuration. A reasonable agreement between the experimental data and computed electromagnetic field topography inside the chamber is reported. The Langmuir probe measurements reveal that the spatial profiles of the electron density, the effective electron temperature, plasma potential, and electron energy distribution/probability functions feature a high degree of the radial and axial uniformity and a weak azimuthal dependence, which is consistent with the earlier theoretical predictions. As the input rf power increases, the azimuthal dependence of the global plasma parameters vanishes. The obtained results demonstrate that by introducing the internal oscillated rf currents one can noticeably improve the uniformity of electromagnetic field topography, rf power deposition, and the plasma density in the reactor.

Inductively coupled plasmas sustained by an internal oscillating current

A global electromagnetic model of an inductively coupled plasma sustained by an internal oscillating current sheet in a cylindrical metal vessel is developed. The electromagnetic field structure, profiles of the rf power transferred to the plasma electrons, electron/ion number density, and working points of the discharge are studied, by invoking particle and power balance. It is revealed that the internal rf current with spatially invariable phase significantly improves the radial uniformity of the electromagnetic fields and the power density in the chamber as compared with conventional plasma sources with external flat spiral inductive coils. This configuration offers the possibility of controlling the rf power deposition in the azimuthal direction.

Effect of an internal rotating current on low-frequency inductively coupled plasmas

The effects of an inductively rotating current were observed on low-frequency inductively coupled plasmas. The spatial distribution of electromagnetic fields was investigated in a cylindrical metallic chamber filled with dense plasma. The distribution of the magnetic field in plasma chamber was observed for rarefied and dense plasmas. The plasma was assumed as uniform in the electromagnetic fields. The results showed the plasma density increased with power and the electron density increased with pressure.