Estudo da sinterização de eletrólito sólido de céria dopada com gadolínia

Fuel cells are electrochemical devices that convert chemical energy in electrical energy by a reaction directly. The solid oxide fuel cell (SOFC) works in temperature between 900ºC up to 1000ºC, Nowadays the most material for ceramic electrolytes is yttria stabilized zirconium. However, the high operation temperature can produce problems as instability and incompatibility of materials, thermal degradation and high cost of the surround materials. These problems can be reduced with the development of intermediate temperature solid oxide fuel cell (IT-SOFC) that works at temperature range of 600ºC to 800ºC. Ceria doped gadolinium is one of the most promising materials for electrolytes IT-SOFC due high ionic conductivity and good compatibility with electrodes. The inhibition of grain growth has been investigated during the sintering to improve properties of electrolytes. Two-step sintering (TSS) is an interesting technical to inhibit this grain growth and consist at submit the sample at two stages of temperature. The first one stage aims to achieve the critical density in the initiating the sintering process, then the sample is submitted at the second stage where the temperature sufficient to continue the sintering without accelerate grain growth until to reach total densification. The goal of this work is to produce electrolytes of ceria doped gadolinium by two-step sintering. In this context were produced samples from micrometric and nanometric powders by two routes of two-step sintering. The samples were obtained with elevate relative density, higher than 90% using low energy that some works at the same area. The average grain size are at the range 0,37 μm up to 0,51 μm. The overall ionic conductivity is 1,8x10-2 S.cm and the activation energy is 0,76 eV. Results shown that is possible to obtain ceria-doped gadolinium samples by two-step sintering technique using modified routes with characteristics and properties necessary to apply as electrolytes of solid oxide fuel cell

Influência das tensões tectônicas na permeabilidade da formação Açu - Bacia Potiguar

The behavior of the fluid flux in oil fields is influenced by different factors and it has a big impact on the recovery of hydrocarbons. There is a need of evaluating and adapting the actual technology to the worldwide reservoirs reality, not only on the exploration (reservoir discovers) but also on the development of those that were already discovered, however not yet produced. The in situ combustion (ISC) is a suitable technique for these recovery of hydrocarbons, although it remains complex to be implemented. The main objective of this research was to study the application of the ISC as an advanced oil recovery technique through a parametric analysis of the process using vertical wells within a semi synthetic reservoir that had the characteristics from the brazilian northwest, in order to determine which of those parameters could influence the process, verifying the technical and economical viability of the method on the oil industry. For that analysis, a commercial reservoir simulation program for thermal processes was used, called steam thermal and advanced processes reservoir simulator (STARS) from the computer modeling group (CMG). This study aims, through the numerical analysis, find results that help improve mainly the interpretation and comprehension of the main problems related to the ISC method, which are not yet dominated. From the results obtained, it was proved that the mediation promoted by the thermal process ISC over the oil recovery is very important, with rates and cumulated production positively influenced by the method application. It was seen that the application of the method improves the oil mobility as a function of the heating when the combustion front forms inside the reservoir. Among all the analyzed parameters, the activation energy presented the bigger influence, it means, the lower the activation energy the bigger the fraction of recovered oil, as a function of the chemical reactions speed rise. It was also verified that the higher the enthalpy of the reaction, the bigger the fraction of recovered oil, due to a bigger amount of released energy inside the system, helping the ISC. The reservoir parameters: porosity and permeability showed to have lower influence on the ISC. Among the operational parameters that were analyzed, the injection rate was the one that showed a stronger influence on the ISC method, because, the higher the value of the injection rate, the higher was the result obtained, mainly due to maintaining the combustion front. In connection with the oxygen concentration, an increase of the percentage of this parameter translates into a higher fraction of recovered oil, because the quantity of fuel, helping the advance and the maintenance of the combustion front for a longer period of time. About the economic analysis, the ISC method showed to be economically feasible when evaluated through the net present value (NPV), considering the injection rates: the higher the injection rate, the higher the financial incomes of the final project

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Conversão térmica e termocatalítica à baixa temperatura do óleo de girassol para obtenção de bio-óleo

The use of biofuels remotes to the eighteenth century, when Rudolf Diesel made the first trials using peanut oil as fuel in a compression ignition engine. Based on these trials, there was the need for some chemical change to vegetable oil. Among these chemical transformations, we can mention the cracking and transesterification. This work aims at conducting a study using the thermocatalytic and thermal cracking of sunflower oil, using the Al-MCM-41 catalyst. The material type mesoporous Al-MCM-41 was synthesized and characterized by Hydrothermical methods of X-ray diffraction, scanning electron microscopy, nitrogen adsorption, absorption spectroscopy in the infrared and thermal gravimetric analysis (TG / DTG).The study was conducted on the thermogravimetric behavior of sunflower oil on the mesoporous catalyst cited. Activation energy, conversion, and oil degradation as a function of temperature were estimated based on the integral curves of thermogravimetric analysis and the kinetic method of Vyazovkin. The mesoporous material Al-MCM-41 showed one-dimensional hexagonal formation. The study of the kinetic behavior of sunflower oil with the catalyst showed a lower activation energy against the activation energy of pure sunflower oil. Two liquid fractions of sunflower oil were obtained, both in thermal and thermocatalytic pyrolisis. The first fraction obtained was called bio-oil and the second fraction obtained was called acid fraction. The acid fraction collected, in thermal and thermocatalytic pyrolisis, showed very high level of acidity, which is why it was called acid fraction. The first fraction was collected bio-called because it presented results in the range similar to petroleum diesel

Pirólise rápida catalítica do capim elefante utilizando materiais mesoporosos e óxidos metálicos para deoxigenação em bio-óleo

The fast pyrolysis of lignocellulosic biomass is a thermochemical conversion process for production energy which have been very atratactive due to energetic use of its products: gas (CO, CO2, H2, CH4, etc.), liquid (bio-oil) and charcoal. The bio-oil is the main product of fast pyrolysis, and its final composition and characteristics is intrinsically related to quality of biomass (ash disposal, moisture, content of cellulose, hemicellulose and lignin) and efficiency removal of oxygen compounds that cause undesirable features such as increased viscosity, instability, corrosiveness and low calorific value. The oxygenates are originated in the conventional process of biomass pyrolysis, where the use of solid catalysts allows minimization of these products by improving the bio-oil quality. The present study aims to evaluate the products of catalytic pyrolysis of elephant grass (Pennisetum purpureum Schum) using solid catalysts as tungsten oxides, supported or not in mesoporous materials like MCM-41, derived silica from rice husk ash, aimed to reduce oxygenates produced in pyrolysis. The biomasss treatment by washing with heated water (CEL) or washing with acid solution (CELix) and application of tungsten catalysts on vapors from the pyrolysis process was designed to improve the pyrolysis products quality. Conventional and catalytic pyrolysis of biomass was performed in a micro-pyrolyzer, Py-5200, coupled to GC/MS. The synthesized catalysts were characterized by X ray diffraction, infrared spectroscopy, X ray fluorescence, temperature programmed reduction and thermogravimetric analysis. Kinetic studies applying the Flynn and Wall model were performed in order to evaluate the apparent activation energy of holoceluloce thermal decomposition on samples elephant grass (CE, CEL and CELix). The results show the effectiveness of the treatment process, reducing the ash content, and were also observed decrease in the apparent activation energy of these samples. The catalytic pyrolysis process converted most of the oxygenate componds in aromatics such as benzene, toluene, ethylbenzene, etc

Degradacao termica e catalitica da borra oleosa de Petroleo com materiais nanoestruturados al-mcm-41 e AL-SBA-15

Aiming to reduce and reuse waste oil from oily sludge generated in large volumes by the oil industry, types of nanostructured materials Al-MCM-41 and Al-SBA-15, with ratios of Si / Al = 50, were synthesized , and calcined solids used as catalysts in the degradation of oily sludge thermocatalytic oil from oilfield Canto do Amaro, in the state of Rio Grande do Norte. Samples of nanostructured materials were characterized by thermogravimetric analysis (TG / DTG), X-ray diffraction (XRD), scanning electron microscopy (SEM), absorption spectroscopy in the infrared Fourier transform (FT-IR) and adsorption nitrogen (BET). The characterization showed that the synthesized materials resulted in a catalyst nanostructure, and ordered pore diameter and surface area according to existing literature. The oily sludge sample was characterized by determining the API gravity and sulfur content and SARA analysis (saturates, aromatics, resins and asphaltenes). The results showed a material equivalent to the average oil with API gravity of 26.1, a low sulfur content and considerable amount of resins and asphaltenes, presented above in the literature. The thermal and catalytic degradation of the oily sludge oil was performed from room temperature to 870 ° C in the ratios of heating of 5, 10 and 20 ° C min-1. The curves generated by TG / DTG showed a more accelerated degradation of oily sludge when it introduced the nanostructured materials. These results were confirmed by activation energy calculated by the method of Flynn-Wall, in the presence of catalysts reduced energy, in particular in the range of cracking, showing the process efficiency, mainly for extraction of lightweight materials of composition of oily sludge, such as diesel and gasoline

Rosuvastatina, doença hepática gordurosa não alcoólica e ativação das células estreladas hepáticas em camundongos

Introdução: A atual epidemia de obesidade tem chamado a atenção para a doença hepática gordurosa não alcoólica (DHGNA). Atualmente não existe um medicamento para o tratamento da esteatose hepática, embora as estatinas sejam muito prescritas para pacientes obesos, este medicamento destina-se ao tratamento da hipercolesterolemia. Este trabalho teve como objetivo investigar os efeitos da rosuvastatina em um modelo de obesidade induzida por dieta, como foco principal a DHGNA e os marcadores hepáticos da lipogênese e beta-oxidação e ativação de células estreladas hepáticas (CEHs) em camundongos. Métodos: Camundongos machos C57BL/6 receberam dieta padrão (SC, 10% de energia como lipídios) ou dieta rica em gorduras (HF, 50% de energia como lipídios) durante 12 semanas. Em seguida, 7 semanas de tratamento, foram feitas, formando os grupos: SC, SCR (SC + rosuvastatina), HF e HFR (HF + rosuvastatina). As análises bioquímicas e técnicas moleculares foram aplicadas para abordar os resultados plasmáticos e moleculares. Resultados: O grupo HF apresentou maiores valores de insulina, colesterol total, triglicerídeos e leptina que o grupo SC, todos os quais foram reduzidos significativamente após o tratamento com Rosuvastatina no grupo HFR. O grupo HF apresentou maior percentual de esteatose, assim como maior ativação das CEHs, enquanto que a rosuvastatina provocou uma redução de 21% na esteatose hepática e atenuou a ativação das CEHs no grupo HFR. Em concordância com os achados histológicos, as expressões de SREBP-1 e PPAR-gama foram aumentados nos animais HF e reduzido após o tratamento no grupo HFR. Por outro lado, a expressão reduzida de PPAR-alfa e CPT-1 foram encontrados nos animais HF, sendo tais parâmetros restaurados após o tratamento no grupo HFR. Conclusão: A rosuvastatina atenua significativamente a ativação das células estreladas na obesidade induzida por dieta, afetando o equilíbrio dos PPARs na lipotoxicidade. Diante desses achados a Rosuvastatina pode ser indicada como alternativa para auxiliar o tratamento da esteatose hepática.

Consumo inteligente de energia elétrica

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Redes de Comunicação e Multimédia

Níveis de energia digestível sobre os desempenhos reprodutivo e zootécnico e a deposição de lipídios nos hepatócitos de machos de tilápia-do-nilo

O experimento foi conduzido com o objetivo de avaliar o desempenho reprodutivo e zootécnico e a deposição de lipídios no tecido hepático de machos de tilápia-do-nilo alimentados com rações contendo diferentes níveis de energia digestível, obtidos com a inclusão de óleo de soja. Foram utilizados 400 reprodutores (300 fêmeas e 100 machos) distribuídos em delineamento inteiramente casualizado, composto de cinco níveis de energia digestível (2.700, 2.950, 3.200, 3.450 e 3.700 kcal.kg de ração-1) e quatro repetições. Os reprodutores foram alimentados com rações contendo 35% de proteína bruta e submetidos ao manejo reprodutivo em hapas por 101 dias. O melhor resultado de concentração espermática e percentual de espermatozoides normais foram obtidos para reprodutores alimentados com rações contendo 3.465,56 e 3.443,43 kcal. kg de ração-1, que produziram 7,98 × 10(9) espermatozoides.mL de sêmen-1 e 38,98% de espermatozoides normais, respectivamente. A produção de sêmen, o pH seminal, o índice de sobrevivência espermática e o tempo de ativação espermática não foram afetados pelos níveis energéticos das rações. Os níveis de energia das rações não influenciaram o desempenho zootécnico dos peixes, mas promoveram aumento linear na deposição de lipídios nos hepatócitos e afetaram a qualidade seminal, estimulando a produção de espermatozoides e a melhora dos índices de normalidade da morfologia espermática em níveis energéticos próximos a 3.450 kcal. kg de ração-1.

Desenvolvimento de redes neurais para previsão de cargas elétricas de sistemas de energia elétrica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Membranas de celulose bacteriana contendo nanopartículas de 'YVO IND. 4': 'YB POT. 3+': 'ER POT. 3+'/'HO POT. 3+' para aplicações envolvendo conversão ascendente de energia

Pós-graduação em Química - IQ

Estudo de propriedades da resina acrílica termoativada por energia de micro-ondas frente às variações nos procedimentos de inclusão

On heat cured acrylic resins by microwaves energy the action of electromagnetic waves on methylmethacrylate promote the polymerization process. However, part of this energy is absorbed by the gypsum present in the flask and the function of this gypsum is to maintain the characteristics of specimen, nevertheless is unknown in the literature as the amount of water present in this gypsum affects the characteristics of acrylic resin. The proposal of this study was verified if dried gypsum influenced in some properties of the acrylic resins thermally activated by microwaves: presence of porosity, microhardness, roughness, flexural strength and dimensional change. Two different types of acrylic resin for complete denture were utilized: Lucitone 550 e Vipi-Wave and groups were formed: Lucitone 550, polymerization by microwave energy without gypsum treatment; Lucitone 550, polymerization by microwave energy with pretreatment gypsum; Vipi-Wave by microwave energy without gypsum treatment; Vipi Wave, polymerization by microwave energy with pretreatment gypsum; Lucitone 550 control group polymerization in hot water bath. For both situations were performed analysis of microhardness and porosity three different metallic shaped specimens were formed with followed dimensions: 2,0x2,0x2,0cm (8cm3); 2,0x2,0x1,0 (4cm3) e 2,0x2,0x0,5 (2cm3). Standardized wax specimens was used to prepare groups (n=9) and included in glass fiber flasks. The gypsum dry was made by microwave oven cycle (10min and 600W) and then the flasks were maintained in dry oven during two hours. Polymerizations of specimens were made and then polished. Wax patterns #7 obtained from the metal were embedded in plastic flask and following the processes of pressing and polymerization of the resin according to established groups. To evaluate the flexural strength, specimens 65mm x 10mm x 3.0mm from metallic patterns in bar format were made. ...

Determinação de elementos traços em diques mesozoicos da Serra do Mar por meio de ativação com nêutrons

A análise de elementos traço, tais como terras raras, TH, U, Ta, Hf, Ba, Rb e Ba, é uma ferramenta muito importante para estudos petrogenéticos. No intuito de estudar tais processos em diques do Enxame Serra do Mar (litoral de São Paulo e Rio de Janeiro), pertencente à Provincia Magmática do Paraná (PMP), uma das províncias de basaltos continentais mais expressivas do mundo, foram realizadas análises por ativação com nêutrons nestes diques. A técnica, empregada no Centro de Reator de pesquisa do Instituto de Pesquisas Energéticas e Nucleares, forneceu concentrações de elementos traço com os níveis de precisão de 10% e exatidão 9% os quais são adequadas para estudos petrogenéticos. Devido as baixas concentrações dos elementos analisados, a rotina experimental de preparação das amostras abrangeu processos bastantes cuidadosos para evitar contaminação. As amostras investigadas podem ser divididas em quatro grupos: rochas básicas (SiO2<55%) com Ti/Y<500; rochas intermediárias (55%63%). Diques de composição intermediária e ácida só ocorrem na Ilha de São Sebastião e na região costeira adjacente. As concentrações de elementos maiores e menores, bem como os padrões de abundância de terras raras e de outros elementos incompatíveis dessas rochas mais diferenciadas, apresentaram semelhanças significativas com os das vulcânicas Chapecó do tipo Ourinhos, sugerindo gênese similar, ou seja, incluindo também processos de contaminação crustal .

Bioquímica quântica na diferenciação dos níveis de ativação de receptores AMPA por agonistas parciais Wilardina

In the central nervous system (CNS) of mammalian, fast synaptic transmission between nerve cells is performed primarily by α-amino-3-hydroxy-5-methyl-4- isoxazolepropionic acid (AMPA) receptors, an ionotropic glutamate receptor that is related with learning, memory and homeostasis of the nervous system. Impairments in their functions are correlated with development of many brain desorders, such as epilepsy, schizophrenia, autism, Parkinson and Alzheimer. The use of willardiine analogs has been shown a powerful tool to understanding of activation and desensitization mechanisms of this receptors, because the modification of a single ligand atom allows the observation of varying levels of efficacy. In this work, taking advantage of Fluorine Willardiine (1.35Å), Hydrogen Willardiine (1.65Å), Bromine Willardiine (1.8Å) and Iodine Willardiine (2.15Å) structures co-crystalized with GluA2 with codes 1MQI, 1MQJ, 1MQH and 1MQG, we attempted to energetically differentiate the four ligands efficacy. The complexes were submitted to energetic calculations based on density functional theory (DFT), under the optics of molecular fractionation with conjugate caps (MFCC) method. Obtained results show a relationship between the energetic values and willardiines efficacy order (FW> HW > BrW > IW), also show the importance of E705, R485, Y450, S654, T655, T480 e P478 as the amino acids that contribute most strongly with the interaction of four partial agonists. Furthermore, we outlined the M708 behaviour, attracted by FW and HW ligands, and repels by BrW and IW. With the datas reported on this work, it is possible for a better understanding of the AMPA receptor, which can serve as an aid in the development of new drugs for this system.

Estudo da intercalação de fontes de potássio em caulinita pura, com tratamento térmico e ativação ácida

The chemical changes in clay minerals has been widely studied in order to improve its properties for use in various applications. However kaolinite has strong hydrogen bonds between their adjacent layers hindering the process changes in its structure. With the objective to facilitate the process of intercalation monobasic potassium phosphate, bibasic potassium phosphate and potassium acetate we was performed on kaolinite heat treatment at 600 °C and activated acidic with phosphoric acid and 5 to 10 mol L-1. The samples they were characterized by energy dispersive spectroscopy (EDS), X-Ray Diffraction (XRD), Infrared Spectroscopy Fourier Transform (FTIR) and Thermogravimetric Analysis (TG) and Differential Thermal Analysis (DTG) and the superficial and textural changes the samples with heat treatment and acid activation they were characterized by scanning electron microscopy (SEM) and Textural Analysis of Adsorption/desorption N2. With the help of the techniques found that, the heat treatment becomes more susceptible to acid activation kaolinite making the samples with two treatments show larger amounts of phosphorus. It was also found that bibasic potassium phosphate binds more strongly the structure of kaolinite by having a structure with two-coordinating oxygens and intercalation with potassium acetate in acid-activated kaolin increases the interlayer distance of the kaolinite and the intercalation occurs with higher response index (RI) for samples with acid activation to 5 mol /L.