Low-carbon cement with waste oil-craking catalyst incorporation

The present paper shows preliminary results of an ongoing project which one of the goals is to investigate the viability of using waste FCC catalyst (wFCC), originated from Portuguese oil refinery, to produce low carbon blended cements. For this purpose, four blended cements were produced by substituting cement CEM I 42.5R up to 20% (w/w) by waste FCC catalyst. Initial and final setting times, consistency of standard paste, soundness and compressive strengths after 2, 7 and 28 days were measured. It was observed that the wFCC blended cements developed similar strength, at 28 days, compared to the reference cement, CEM I 42.5R. Moreover, cements with waste FCC catalyst incorporation up to 15% w/w meet European Standard EN 197-1 specifications for CEM II/A type cement, in the 42.5R strength class.

Produção centralizada a biogás - análise do impacto a nível cooperativo

A utilização de energia renovável é hoje tema abordado em todo o mundo, devido à preocupação com a preservação do meio ambiente. Entre as energias renováveis, a biomassa destaca-se pela excelente disponibilidade que possui. Os dejetos bovinos são uma das mais abundantes, o qual tem grande potencial energético, se fermentado corretamente em biodigestores, obtendo como um dos produtos finais, o biogás. Esse gás é constituído na sua maior parte por gás metano (CH4) que é altamente inflamável. Neste trabalho pretende-se fazer a avaliação do potencial energético das propriedades de produção de leite na região do concelho de BRAGA aplicando uma tecnologia de queima de biogás e de produção de eletricidade utilizando um sistema de cogeração convencional e uma tecnologia mais recente, o Organic Rankine Cycle (ORC) e explicitando a respetiva análise económica. As opções por um sistema ORC na central em análise foram justificadas ponderando as vantagens e desvantagens deste ciclo em relação ao ciclo de vapor de água. O objetivo é a obtenção de energia elétrica e térmica e o aumento do rendimento global da instalação com o aproveitamento de todas as energias disponíveis, assim como a eliminação da toxidade dos dejetos para aproveitamento como biomassa. Partindo do levantamento bibliográfico e caraterização das diversas propriedades existentes no concelho, utilizando a tecnologia mais indicada e atual para este tipo de instalação. A biomassa utilizada foi uma mistura de dejetos bovinos com água. O biogás produzido foi convertido em energia elétrica e térmica, através da sua queima. Tem-se assim uma central que além de dar destino adequado aos dejetos animais, diminui a contaminação ambiental, evita a emissão de gás metano para a atmosfera e produz biogás. Efetua-se os cálculos económicos para dois cenários distintos, implementação de uma central de valorização de biogás em cada um dos oito maiores produtores de leite do núcleo de Penso e o aproveitamento dos dejetos produzidos pelos mesmos para implementação de uma central global de recolha dos mesmos, onde é feito o tratamento dos mesmos e a consequente produção de biogás. Na análise económica foram utilizados os seguintes critérios: o VAL (valor atual líquido), a TIR (taxa interna de rendibilidade) e o Período de Retorno Financeiro do Projeto.

Melhoria do processo produtivo

A dissertação descreve o levantamento e otimização do processo de fabrico de uma peça plástica para um automóvel. A otimização deste processo produtivo tem em vista a rentabilização de recursos humanos, a redução de custos associados e a redução de atividades ao longo do processo, tais como armazenamento de produto semiacabado, uma vez que este deixa de existir, a eliminação de fluxos logísticos e a eliminação do posto de montagem de componentes desta peça. A metodologia utilizada neste projeto centra-se na aplicação de ferramentas que permitem a análise e melhoria de processos produtivos, tais como o diagrama de processo, o diagrama spaghetti, o PDCA, a cronometragem dos tempos por tarefa e a aplicação de uma heurística para o balanceamento do futuro posto de trabalho da peça em estudo. O diagrama de processo, o diagrama de spaghetti e a cronometragem dos tempos por tarefas mostraram o estado atual do processo produtivo. Da análise do atual estado verifica-se que existe muito desperdício de mão-de-obra nas duas estações de trabalho, injeção e montagem. A eliminação do posto de trabalho exclusivo para montagem e junção dos processos de injeção e montagem no mesmo posto de trabalho, com a aplicação de uma heurística para balanceamento do novo posto de trabalho, demonstra que os ganhos são muito significativos. A aplicação do ciclo PDCA, na base da qual está a elaboração de um plano de ações, tornará esta mudança possível e bem-sucedida. A intenção deste projeto é demonstrar que o estado atual pode sempre ser melhorado se se usarem as ferramentas corretas para análise e proposta de melhorias que trarão ganhos à empresa a curto prazo. Usando esta sugestão, a empresa poderá dar início a um novo ciclo em que o espírito de melhoria esteja presente todos os dias em toda a organização.

Desenvolvimento de um jogo de simulação do sistema de produção LEAN ferramentas: 5S, organização de layout e TPM

O Lean Thinking (Pensamento Magro) baseia-se no Sistema Toyota de Produção, também conhecido pela sigla TPS (Toyota Production System). Foi desenvolvido em ambiente fabril, em particular na indústria automóvel, por Taiichi Ohno (1988) com o principal objectivo de eliminar desperdícios. O Lean Thinking tem crescido e hoje é muito mais abrangente. Com o intuito de melhorar a aprendizagem dos conceitos e das práticas lean, têm sido desenvolvidos diversos jogos que simulam a utilização das diferentes ferramentas lean. Estes jogos têm uma vertente comercial e são especialmente dirigidos para a indústria contudo não se consegue encontrar um que consiga ser utilizado para simular individualmente as ferramentas Lean. No âmbito desta dissertação, foi desenvolvido um jogo didáctico para apoio nas aulas onde são estudadas as ferramentas Lean. As ferramentas Lean abordadas neste trabalho são: 5S, Organização de Layout e Total Productive Maintenance. O jogo desenvolvido permite introduzir as ferramentas individualmente e as simulações efectuadas possibilitam a análise das melhorias obtidas com a eliminação de desperdícios através da aplicação das diferentes ferramentas.

Location model for CCA-treated - wood waste remediation units

Dissertação apresentada como requisito parcial para obtenção do grau de Mestre em Ciência e Sistemas de Informação Geográfica

Mechanical behaviour analysis of polyester polymer mortars modified with recycled GFRP waste materials

In this study the effect of incorporation of recycled glass-fibre reinforced polymer (GFRP) waste materials, obtained by means of milling processes, on mechanical behaviour of polyester polymer mortars was assessed. For this purpose, different contents of recycled GFRP waste powder and fibres, with distinct size gradings, were incorporated into polyester based mortars as sand aggregates and filler replacements. Flexural and compressive loading capacities were evaluated and found better than unmodified polymer mortars. GFRP modified polyester based mortars also show a less brittle behaviour, with retention of some loading capacity after peak load. Obtained results highlight the high potential of recycled GFRP waste materials as efficient and sustainable reinforcement and admixture for polymer concrete and mortars composites, constituting an emergent waste management solution.

Optimization process of polyester polymer mortars modified with recycled GFRP waste aggregates – application of factorial experiment design-

Glass fibre-reinforced plastics (GFRP), nowadays commonly used in the construction, transportation and automobile sectors, have been considered inherently difficult to recycle due to both: cross-linked nature of thermoset resins, which cannot be remolded, and complex composition of the composite itself, which includes glass fibres, matrix and different types of inorganic fillers. Presently, most of the GFRP waste is landfilled leading to negative environmental impacts and supplementary added costs. With an increasing awareness of environmental matters and the subsequent desire to save resources, recycling would convert an expensive waste disposal into a profitable reusable material. There are several methods to recycle GFR thermostable materials: (a) incineration, with partial energy recovery due to the heat generated during organic part combustion; (b) thermal and/or chemical recycling, such as solvolysis, pyrolisis and similar thermal decomposition processes, with glass fibre recovering; and (c) mechanical recycling or size reduction, in which the material is subjected to a milling process in order to obtain a specific grain size that makes the material suitable as reinforcement in new formulations. This last method has important advantages over the previous ones: there is no atmospheric pollution by gas emission, a much simpler equipment is required as compared with ovens necessary for thermal recycling processes, and does not require the use of chemical solvents with subsequent environmental impacts. In this study the effect of incorporation of recycled GFRP waste materials, obtained by means of milling processes, on mechanical behavior of polyester polymer mortars was assessed. For this purpose, different contents of recycled GFRP waste materials, with distinct size gradings, were incorporated into polyester polymer mortars as sand aggregates and filler replacements. The effect of GFRP waste treatment with silane coupling agent was also assessed. Design of experiments and data treatment were accomplish by means of factorial design and analysis of variance ANOVA. The use of factorial experiment design, instead of the one factor at-a-time method is efficient at allowing the evaluation of the effects and possible interactions of the different material factors involved. Experimental results were promising toward the recyclability of GFRP waste materials as polymer mortar aggregates, without significant loss of mechanical properties with regard to non-modified polymer mortars.

Experiments on new polymer based mortars filled with FRP waste recyclates - a quantitative analysis

Glass fibre-reinforced plastics (GFRP) have been considered inherently difficult to recycle due to both: cross-linked nature of thermoset resins, which cannot be remolded, and complex composition of the composite itself. Presently, most of the GFRP waste is landfilled leading to negative environmental impacts and supplementary added costs. With an increasing awareness of environmental matters and the subsequent desire to save resources, recycling would convert an expensive waste disposal into a profitable reusable material. In this study, efforts were made in order to recycle grinded GFRP waste, proceeding from pultrusion production scrap, into new and sustainable composite materials. For this purpose, GFRP waste recyclates, were incorporated into polyester based mortars as fine aggregate and filler replacements at different load contents and particle size distributions. Potential recycling solution was assessed by mechanical behaviour of resultant GFRP waste modified polymer mortars. Results revealed that GFRP waste filled polymer mortars present improved flexural and compressive behaviour over unmodified polyester based mortars, thus indicating the feasibility of the waste reuse in polymer mortars and concrete. © 2011, Advanced Engineering Solutions.

Aplicação da filosofia Lean a um caso de estudo para otimização de processos de construção na pré-fabricação de peças de betão

Dissertação de Natureza Científica para obtenção do grau de Mestre em Engenharia Civil, perfil de Edificações

Recycling of pultrusion production waste into innovative concrete-polymer composite solutions

In this study, the added value resultant from the incorporation of pultrusion production waste into polymer based concretes was assessed. For this purpose, different types of thermoset composite scrap material, proceeding from GFRP pultrusion manufacturing process, were mechanical shredded and milled into a fibrous-powdered material. Resultant GFRP recyclates, with two different size gradings, were added to polyester based mortars as fine aggregate and filler replacements, at various load contents between 4% up to 12% in weight of total mass. Flexural and compressive loading capacities were evaluated and found better than those of unmodified polymer mortars. Obtained results highlight the high potential of recycled GFRP pultrusion waste materials as efficient and sustainable admixtures for concrete and mortar-polymer composites, constituting an emergent waste management solution.

GFRP waste reinforced polymer mortars: a new waste management solution for GFRP scrap material

To date, glass fibre reinforced polymer (GFRP) waste recycling is very limited and restricted by thermoset nature of binder matrix and lack of economically viable enduse applications for the recyclates. In this study, efforts were made in order to recycle grinded GFRP waste proceeding from pultrusion production scrap, into new and sustainable composite materials. For this purpose, GFRP waste recyclates, a mix of powdered and fibrous materials, were incorporated into polyester based mortars as fine aggregate and filler replacements, at different load contents (between 4% up to 12% of total mass) and particle size distributions. Potential recycling solution was assessed by mechanical behaviour of resultant GFRP waste modified polymer mortars. Test results revealed that GFRP waste filled polymer mortars present improved flexural and compressive behaviour over unmodified polyester based mortars, thus indicating the feasibility of GFRP waste reuse in concrete-polymer composites.

Waste recovery into activated carbon for water purification from heavy metals

Dissertação apresentada para obtenção do Grau de Doutor em Engenharia Química Pela Universidade Nova de Lisboa,Faculdade de Ciências e Tecn

Mechanical performance of concrete made with aggregates from construction and demolition waste recycling plants

This research aims at analysing the mechanical performance of concrete with recycled aggregates (RA) from construction and demolition waste (CDW) from various locations in Portugal. First the characteristics of the various aggregates (natural and recycled) used in the production of concrete were thoroughly analysed. The composition of the RA was determined and several physical and chemical tests of the aggregates were performed. In order to evaluate the mechanical performance of concrete, compressive strength (in cubes and cylinders), splitting tensile strength, modulus of elasticity and abrasion resistance tests were performed. Concrete mixes with RA from CDW from several recycling plants were evaluated, in order to understand the influence that the RA's collection point, and consequently their composition, has on the characteristics of the mixes produced. The analysis of the mechanical performance allowed concluding that the use of RA worsens most of the properties tested, especially when fine RA are used. On the other hand, there was an increase in abrasion resistance when coarse RA were used. In global terms, the use of this type of aggregates, in limited contents, is viable from a mechanical viewpoint. (C) 2015 Elsevier Ltd. All rights reserved.

Performance of concrete made with aggregates recycled from precasting industry waste: influence of the crushing process

The aim of this paper is to evaluate the influence of the crushing process used to obtain recycled concrete aggregates on the performance of concrete made with those aggregates. Two crushing methods were considered: primary crushing, using a jaw crusher, and primary plus secondary crushing (PSC), using a jaw crusher followed by a hammer mill. Besides natural aggregates (NA), these two processes were also used to crush three types of concrete made in laboratory (L20, L45 e L65) and three more others from the precast industry (P20, P45 e P65). The coarse natural aggregates were totally replaced by coarse recycled concrete aggregates. The recycled aggregates concrete mixes were compared with reference concrete mixes made using only NA, and the following properties related to the mechanical and durability performance were tested: compressive strength; splitting tensile strength; modulus of elasticity; carbonation resistance; chloride penetration resistance; water absorption by capillarity; water absorption by immersion; and shrinkage. The results show that the PSC process leads to better performances, especially in the durability properties.

Physical, chemical and mineralogical properties of fine recycled aggregates made from concrete waste

This paper assesses the physical, chemical and mineralogical characteristics of fine recycled aggregates obtained from crushed concrete waste, comparing them with two types of natural fine aggregates from different origins. A commercial concrete was jaw crushed, and the effect of different aperture sizes on the particle size distribution of the resulting aggregates was evaluated. The density and water absorption of the recycled aggregates was determined and a model for predicting water absorption over time is proposed. Both natural and recycled aggregates were characterized regarding bulk density and fines content. Recycled aggregates were additionally characterized by XRD, SEM/EDS and DTA/TG of individual size fractions. The results show that natural and recycled fine aggregates have very different characteristics. This should be considered in potential applications, both in terms of the limits for replacing amounts and of the rules and design criteria of the manufactured products. (C) 2015 Elsevier Ltd. All rights reserved.