Effect of incorporation of nutraceutical capsule waste of safflower oil in the mechanical characteristics of corn starch films

Abstract Biodegradable films blends made of safflower oil nutraceutical capsules waste corn starch (20:4, 30:4, 40:4 and 50:4) were prepared. The objective of this study was to evaluate the influence of addition of different concentrations of safflower oil nutraceutical capsule waste in the mechanical properties (tensile strength, elongation at break, Young’s modulus) and thickness of corn starch films. A decrease in tensile strength and Young’s modulus and an increase in elongation at break were observed with the increase in the content of the nutraceutical capsule waste. The results showed that the blends of safflower oil capsules waste-corn starch films demonstrated promising characteristics to form biodegradable films with different mechanical characteristics.

A biochemical predictor of performance during mesophilic anaerobic fermentation of starch wastewater

The aim of this study was to determine the potential of biochemical parameters, such as enzyme activity and adenosine triphosphate (ATP) levels, as monitors of process performance in the Upflow Anaerobic Sludge Blanket (UASB) reactor utilizing a starch wastewater. The acid and alkaline phosphatase activity and the ATP content of the UASB sludge were measured in response to changes in flow rate and nutrient loading. Conventional parameters of process performance, such as gas production, acetic acid production, COD, phosphorus, nitrogen and suspended solids loadings and % COD removal were also monitored. The response of both biochemical and conventional parameters to changing process conditions was then compared. Alkaline phosphatase activity exhibited the highest activity over the entire study perioda A high suspended solids loading was observed to upset the system in terms of gas production, acetic acid production and % COD removala The initial rate of increase in alkaline phosphatase activity following an increase in loading was four times as great during process upset than under conditions of good performance. The change in enzyme actiVity was also more sensitive to process upset than changes in acetic acid production. The change in ATP content of the sludge with time suggested that enzyme actiVity was changing independently of the actual viable biomass present. The bacterial composition of the anaerobic sludge granules was similar to that of other sludge bed systems, at the light and scanning electron microscope level. Isolated serum bottle cultures produced several acids involved in anaerobic carbohydrate metabolism. The overall performance of the UASB system indicated that higher loadings of soluble nutrients could have been tolerated by the system.

Canada Starch Company (CASCO) Fonds, 1980-1987, n.d.

CASCO (Canada Starch Company) began operations in 1982 and was officially opened in May of 1983. Premier William Davis was in attendance. CASCO is a company whose roots can be traced back to 1858 when it was founded by W.T. Benson in Cardinal, Ontario. The company grew as corn uses were developed. Corn derived products now include: corn oil, liquid sweetener and feed for dairy and cattle. Starch is used as a finish for fine papers, a component in dry cell batteries, pharmaceuticals, wallpaper, film, tires, surgical dressings, plastics and plywood. Corn syrup is used in beverages, canned fruit, frozen seafood, licorice, ice cream and baking products. Corn solubles are used in animal feed, rubber substitutes, soap, paint and varnish. There are more than 250 industrial and food uses for corn

Investigation of femtosecond laser technology for the fabrication of drug nanocrystals in suspension

La technique du laser femtoseconde (fs) a été précédemment utilisée pour la production de nanoparticules d'or dans un environnement aqueux biologiquement compatible. Au cours de ce travail de maîtrise, cette méthode a été investiguée en vue d'une application pour la fabrication de nanocristaux de médicament en utilisant le paclitaxel comme modèle. Deux procédés distincts de cette technologie à savoir l'ablation et la fragmentation ont été étudiés. L'influence de la puissance du laser, de point de focalisation, et de la durée du traitement sur la distribution de taille des particules obtenues ainsi que leur intégrité chimique a été évaluée. Les paramètres ont ainsi été optimisés pour la fabrication des nanoparticules. L’évaluation morphologique et chimique a été réalisée par microscopie électronique et spectroscopie infrarouge respectivement. L'état cristallin des nanoparticules de paclitaxel a été caractérisé par calorimétrie differentielle et diffraction des rayons X. L'optimisation du procédé de production de nanoparticules par laser fs a permis d'obtenir des nanocristaux de taille moyenne (400 nm, polydispersité ≤ 0,3). Cependant une dégradation non négligeable a été observée. La cristallinité du médicament a été maintenue durant la procédure de réduction de taille, mais le paclitaxel anhydre a été transformé en une forme hydratée. Les résultats de cette étude suggèrent que le laser fs peut générer des nanocristaux de principe actif. Cependant cette technique peut se révéler problématique pour des médicaments sensibles à la dégradation. Grâce à sa facilité d'utilisation et la possibilité de travailler avec des quantités restreintes de produit, le laser fs pourrait représenter une alternative valable pour la production de nanoparticules de médicaments peu solubles lors des phases initiales de développement préclinique. Mots-clés: paclitaxel, nanocristaux, laser femtoseconde, ablation, fragmentation

High-amylose carboxymethyl starch matrices for oral sustained drug-release : in vitro and in vivo evaluation

Les amidons non modifiées et modifiés représentent un groupe d’excipients biodégradables et abondants particulièrement intéressant. Ils ont été largement utilisés en tant qu’excipients à des fins diverses dans des formulations de comprimés, tels que liants et/ou agents de délitement. Le carboxyméthylamidon sodique à haute teneur en amylose atomisé (SD HASCA) a été récemment proposé comme un excipient hydrophile à libération prolongée innovant dans les formes posologiques orales solides. Le carboxyméthylamidon sodique à haute teneur en amylose amorphe (HASCA) a d'abord été produit par l'éthérification de l'amidon de maïs à haute teneur en amylose avec le chloroacétate. HASCA a été par la suite séché par atomisation pour obtenir le SD HASCA. Ce nouvel excipient a montré des propriétés présentant certains avantages dans la production de formes galéniques à libération prolongée. Les comprimés matriciels produits à partir de SD HASCA sont peu coûteux, simples à formuler et faciles à produire par compression directe. Le principal objectif de cette recherche était de poursuivre le développement et l'optimisation des comprimés matriciels utilisant SD HASCA comme excipient pour des formulations orales à libération prolongée. A cet effet, des tests de dissolution simulant les conditions physiologiques du tractus gastro-intestinal les plus pertinentes, en tenant compte de la nature du polymère à l’étude, ont été utilisés pour évaluer les caractéristiques à libération prolongée et démontrer la performance des formulations SD HASCA. Une étude clinique exploratoire a également été réalisée pour évaluer les propriétés de libération prolongée de cette nouvelle forme galénique dans le tractus gastro-intestinal. Le premier article présenté dans cette thèse a évalué les propriétés de libération prolongée et l'intégrité physique de formulations contenant un mélange comprimé de principe actif, de chlorure de sodium et de SD HASCA, dans des milieux de dissolution biologiquement pertinentes. L'influence de différentes valeurs de pH acide et de temps de séjour dans le milieu acide a été étudiée. Le profil de libération prolongée du principe actif à partir d'une formulation de SD HASCA optimisée n'a pas été significativement affecté ni par la valeur de pH acide ni par le temps de séjour dans le milieu acide. Ces résultats suggèrent une influence limitée de la variabilité intra et interindividuelle du pH gastrique sur la cinétique de libération à partir de matrices de SD HASCA. De plus, la formulation optimisée a gardé son intégrité pendant toute la durée des tests de dissolution. L’étude in vivo exploratoire a démontré une absorption prolongée du principe actif après administration orale des comprimés matriciels de SD HASCA et a montré que les comprimés ne se sont pas désintégrés en passant par l'estomac et qu’ils ont résisté à l’hydrolyse par les α-amylases dans l'intestin. Le deuxième article présente le développement de comprimés SD HASCA pour une administration orale une fois par jour et deux fois par jour contenant du chlorhydrate de tramadol (100 mg et 200 mg). Ces formulations à libération prolongée ont présenté des valeurs de dureté élevées sans nécessiter l'ajout de liants, ce qui facilite la production et la manipulation des comprimés au niveau industriel. La force de compression appliquée pour produire les comprimés n'a pas d'incidence significative sur les profils de libération du principe actif. Le temps de libération totale à partir de comprimés SD HASCA a augmenté de manière significative avec le poids du comprimé et peut, de ce fait, être utilisé pour moduler le temps de libération à partir de ces formulations. Lorsque les comprimés ont été exposés à un gradient de pH et à un milieu à 40% d'éthanol, un gel très rigide s’est formé progressivement sur leur surface amenant à la libération prolongée du principe actif. Ces propriétés ont indiqué que SD HASCA est un excipient robuste pour la production de formes galéniques orales à libération prolongée, pouvant réduire la probabilité d’une libération massive de principe actif et, en conséquence, des effets secondaires, même dans le cas de co-administration avec une forte dose d'alcool. Le troisième article a étudié l'effet de α-amylase sur la libération de principe actif à partir de comprimés SD HASCA contenant de l’acétaminophène et du chlorhydrate de tramadol qui ont été développés dans les premières étapes de cette recherche (Acetaminophen SR et Tramadol SR). La modélisation mathématique a montré qu'une augmentation de la concentration d’α-amylase a entraîné une augmentation de l'érosion de polymère par rapport à la diffusion de principe actif comme étant le principal mécanisme contrôlant la libération de principe actif, pour les deux formulations et les deux temps de résidence en milieu acide. Cependant, même si le mécanisme de libération peut être affecté, des concentrations d’α-amylase allant de 0 UI/L à 20000 UI/L n'ont pas eu d'incidence significative sur les profils de libération prolongée à partir de comprimés SD HASCA, indépendamment de la durée de séjour en milieu acide, le principe actif utilisé, la teneur en polymère et la différente composition de chaque formulation. Le travail présenté dans cette thèse démontre clairement l'utilité de SD HASCA en tant qu'un excipient à libération prolongée efficace.

Glucoamylase immobilized on montmorillonite: Synthesis, characterization and starch hydrolysis activity in a fixed bed reactor

Glucoamylase from Aspergillus Niger was immobilized on montmorillonite clay (K-10) by two procedures, adsorption and covalent binding. The immobilized enzymes were characterized using XRD, surface area measurements and 27Al MAS NMR and the activity of the immobilized enzymes for starch hydrolysis was tested in a fixed bed reactor (FBR). XRD shows that enzyme intercalates into the inter-lamellar space of the clay matrix with a layer expansion up to 2.25 nm. Covalently bound glucoamylase demonstrates a sharp decrease in surface area and pore volume that suggests binding of the enzyme at the pore entrance. NMR studies reveal the involvement of octahedral and tetrahedral Al during immobilization. The performance characteristics in FBR were evaluated. Effectiveness factor (η) for FBR is greater than unity demonstrating that activity of enzyme is more than that of the free enzyme. The Michaelis constant (Km) for covalently bound glucoamylase was lower than that for free enzyme, i.e., the affinity for substrate improves upon immobilization. This shows that diffusional effects are completely eliminated in the FBR. Both immobilized systems showed almost 100% initial activity after 96 h of continuous operation. Covalent binding demonstrated better operational stability.

Ionomer Compatibilized Low Density Polyethylene - Tapioca Starch Blends Biodegradability and Photodegradability

Biodegradation is the chemical degradation of materials brought about by the action of naturally occurring microorganisms. Biodegradation is a relatively rapid process under suitable conditions of moisture, temperature and oxygen availability. The logic behind blending biopolymers such as starch with inert polymers like polyethylene is that if the biopolymer component is present in sufficient amount, and if it is removed by microorganisms in the waste disposal environment, then the base inert plastic should slowly degrade and disappear. The present work focuses on the preparation of biodegradable and photodegradable blends based on low density polyethylene incorporating small quantities of ionomers as compatibilizers. The thesis consists of eight chapters. The first chapter presents an introduction to the present research work and literature survey. The details of the materials used and the experimental procedures undertaken for the study are described in the second chapter. Preparation and characterization of low density polyethylene (LDPE)-biopolymer (starch/dextrin) blends are described in the third chapter. The result of investigations on the effect of polyethylene-co-methacrylic acid ionomers on the compatibility of LDPE and starch are reported in chapter 4. Chapter 5 has been divided into two parts. The first part deals with the effect of metal oxides on the photodegradation of LDPE. The second part describes the function of metal stearates on the photodegradation of LDPE. The results of the investigations on the role of various metal oxides as pro-oxidants on the degradation of ionomer compatibilized LDPE-starch blends are reported in chapter 6. Chapter 7 deals with the results of investigations on the role of various metal stearates as pro-oxidants on the degradation of ionomer compatibilized LDPE-starch blends. The conclusion of the investigations is presented in the last chapter of the thesis.

Investigations on some amino acid based single crystals for nonlinear optical applications and amino acid capped nanocrystals

Organic crystals possess extremely large optical nonlinearity compared to inorganic crystals. Also organic compounds have the amenability for synthesis and scope for introducing desirable characteristics by inclusions. A wide variety of organic materials having electron donor and acceptor groups, generate high order of nonlinearity. In the present work, a new nonlinear optical crystal, L-citrulline oxalate (LCO) based on the aminoacid L-citrulline was grown using slow evaporation technique. Structural characterization was carried out by single crystal XRD. It crystallizes in the noncentrosymmetric, orthorhombic structure with space group P21 P21 P21. Functional groups present in the sample were identified by Fourier transform infra red (FTIR) and FT-Raman spectral analysis. On studying the FTIR and Raman spectra of the precursors L-citrulline and oxalic acid, used for growing L-citrulline oxalate crystal, it is found that the significant peaks of the precursors are present in the spectra of the L-citrulline oxalate crystal . This observation along with the presence of NH3 + group in the spectra of L-citrulline oxalate, confirms the formation of the charge transfer complex

Investigations on novel polymer nano composites and bio-compatible manganese doped ZnS nanocrystals for photonic and bio-imaging applications

Fluorescence is a powerful tool in biological research, the relevance of which relies greatly on the availability of sensitive and selective fluorescent probes. Nanometer sized fluorescent semiconductor materials have attracted considerable attention in recent years due to the high luminescence intensity, low photobleaching, large Stokes’ shift and high photochemical stability. The optical and spectroscopic features of nanoparticles make them very convincing alternatives to traditional fluorophores in a range of applications. Efficient surface capping agents make these nanocrystals bio-compatible. They can provide a novel platform on which many biomolecules such as DNA, RNA and proteins can be covalently linked. In the second phase of the present work, bio-compatible, fluorescent, manganese doped ZnS (ZnS:Mn) nanocrystals suitable for bioimaging applications have been developed and their cytocompatibility has been assessed. Functionalization of ZnS:Mn nanocrystals by safe materials results in considerable reduction of toxicity and allows conjugation with specific biomolecules. The highly fluorescent, bio-compatible and water- dispersible ZnS:Mn nanocrystals are found to be ideal fluorescent probes for biological labeling

Biodegradability Studies on LDPE-Starch Blends using Amylase-Producing Vibrios

Low-density polyethylene, (LDPE) was mixed with two grades of tapioca starch–lowgrade and high-grade. Various compositions were prepared and mechanical and thermal studies performed. The biodegradability of these samples was checked using a culture medium containing Vibrios (an amylase-producing bacteria), which was isolated from a marine benthic environment. The soil burial test and reprocessability of these samples were checked. The studies on biodegradability show that these blends are partially biodegradable. These low-density polyethylene-starch blends are reprocessable without sacrificing much of their mechanical properties

In vitro degradability of mature and immature leaves of tropical forage legumes differing in condensed tannin and non-starch polysaccharide content and composition

A study was designed to examine the relationships between protein, condensed tannin and cell wall carbohydrate content and composition and the nutritional quality of seven tropical legumes (Desmodium ovalifolium, Flemingia macrophylla, Leucaena leucocephala, L pallida, L macrophylla, Calliandra calothyrsus and Clitotia fairchildiana). Among the legume species studied, D ovalifolium showed the lowest concentration of nitrogen, while L leucocephala showed the highest. Fibre (NDF) content was lowest in C calothyrsus, L Leucocephala and L pallida and highest in L macrophylla, which had no measurable condensed tannins. The highest tannin concentration was found in C calothyrsus. Total non-structural polysaccharides (NSP) varied among legumes species (lowest in C calothyrsus and highest in D ovalifolium), and glucose and uronic acids were the most abundant carbohydrate constituents in all legumes. Total NSP losses were lowest in F macrophylla and highest in L leucocephala and L pallida. Gas accumulation and acetate and propionate levels were 50% less with F macrophylla and D ovalifolium as compared with L leucocephala. The highest levels of branched-chain fatty acids were observed with non-tanniniferous legumes, and negative concentrations were observed with some of the legumes with high tannin content (D ovalifolium and F macrophylla). Linear regression analysis showed that the presence of condensed tannins was more related to a reduction of the initial rate of gas production (0-48 h) than to the final amount of gas produced or the extent (144h) of dry matter degradation, which could be due to differences in tannin chemistry. Consequently, more attention should be given in the future to elucidating the impact of tannin structure on the nutritional quality of tropical forage legumes. (C) 2003 Society of Chemical Industry.

Abomasal infusion of casein, starch and soybean oil differentially affect plasma concentrations of gut peptides and feed intake in lactating dairy cows

The effects of specific nutrients on secretion and plasma concentrations of gut peptides (glucagon-like peptide-1((7-36)) amide (GLP-1), glucose-dependent insulinotropic polypeptide (GIP), and cholecystokinin-8 (CCK)) differ across species, but are not reported for cattle. Our objective was to determine acute (hours) and chronic (1 week) effects of increased abomasal supply of protein, carbohydrate, or fat to the small intestine on dry matter intake (DMI) and plasma concentrations of GLP-1, GIP, CCK, and insulin. Four mid-lactation Holstein cows were used in a 4 x 4 Latin square design experiment. Treatments were 7-day abomasal infusions of water, soybean oil (500 g/d), corn starch (1100 g/d), or casein (800 g/d). Jugular vein plasma was obtained over 7 h at the end of the first and last day of infusions. Oil infusion decreased DMI on day 7, but total metabolizable energy (ME) supply (diet plus infusate) did not differ from water infusion. Casein and starch infusion had no effect on feed DMI; thus, ME supply increased. Decreased DMI on day 7 of oil infusion was accompanied by increased plasma GLP-1 concentration, but decreased plasma CCK concentration. Increased plasma GIP concentration was associated with increased ME supply on day 7 of casein and starch infusion. Casein infusion tended to increase plasma CCK concentration on both days of sampling, and increased plasma GLP-1 and insulin concentration on day 1 of infusion. The present data indicate a sustained elevation of plasma concentration of GLP-1, but not CCK, may contribute to the reduced DMI observed in dairy cows provided supplemental fat. (C) 2008 Elsevier Inc. All rights reserved.