Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Hydrogenation of cinnamaldehyde over Pt/RHCs in supercritical carbon dioxide - Influence of support pretreatment and phase behavior

The selective hydrogenation of cinnamaldehyde (CAL) was investigated using rice husk-based porous carbon (RHCs) supported platinum catalysts in supercritical carbon dioxide (SCCO2). The effects of surface chemistry treatment of the support and the reaction phase behavior have been examined. The Pt/H-RHCs (HNO3-pretreated) was more active for CAL hydrogenation compared with Pt/NH3 - RHCs (NH3 center dot H2O-pretreated). The Pt/RHCs catalyst exhibited a higher selectivity to cinnamyl alcohol (COL) compared with commercial catalyst of Pt/C, which is relative to the micro - mesoporosity structure of the RHCs.

Avaliação da auto-suficiência energética na indústria nacional arrozeira

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia mecânica

Estudo de Argamassas com Cinza de Casca de Amêndoa

Perante o elevado consumo de materiais naturais no processo e produtos na área da construção civil, o reaproveitamento de resíduos é uma das soluções a ser estudada. As cinzas agroindustriais têm lugar de destaque entre estes resíduos, pois têm a possibilidade de aplicação em materiais cimentícios, reduzindo assim o consumo de cimento de Portland. O presente estudo debruça-se sobre a substituição parcial (1,5% e 5%) de cimento de Portland por cinzas de casca de amêndoa. Realizaram-se provetes com diferentes tipos de argamassas: (i) uma de controlo sem substituição de cimento (ARF); (ii) uma com 1,5% de substituição parcial de cimento por cinzas de casca de amêndoa (CCA 1,5%); (iii) e uma com 5% de substituição parcial de cimento por cinza de casca de amêndoa (CCA 5%). Executaram-se ensaios para resistências mecânicas aos 3, 7, 14, 28 e 41 dias de idade. A nível químico pode-se concluir que esta cinza de casca de amêndoa não apresentou qualquer potencial pozolânico. A trabalhabilidade na generalidade diminui ligeiramente, contendo cinza de casca de amêndoa, mas ainda assim considerando-se de fácil manuseamento. Em relação às resistências mecânicas, pode-se concluir que o ideal é a substituição parcial de cimento com 1,5%, pois as resistências diminuem com o uso de uma maior percentagem de substituição, ou seja, o ideal é substituir em pequenas percentagens. Com os dados obtidos, conclui-se que as cinzas testadas não apresentam características necessárias para serem consideradas pozolanas e se será viável a sua utilização mesmo como filer.

Sustainable Building Materials in Kerala – An Overview

Kerala, God’s own country is blessed with immense natural resources. It’s high time that the state’s natural resources being utilized effectively. While sustainable development is the need of the hour, we have to take lead in initiating activities that would minimize the exploitation of our natural resources resulting in their effective utilization. This paper narrates an overview of innovative building materials especially using natural fibres available in Kerala and discusses the feasibility of utilising such fibres in the context of sustainable building materials in Kerala. The paper also discusses how these materials can be effectively utilized to reduce the huge investment in the construction industry

Studies on Landfill Leachate Transportation and Its Impact on Soil Characteristics

Leachate from an untreated landfill or landfill with damaged liners will cause the pollution of soil and ground water. Here an attempt was made to generate knowledge on concentrations of all relevant pollutants in soil due to municipal solid waste landfill leachate and its migration through soil and also to study the effect of leachate on the engineering properties of soil. To identify the pollutants in soil due to the leachate generated from municipal solid waste landfill site, a case study on an unlined municipal solid waste landfill at Kalamassery has been done. Soil samples as well as water samples were collected from the site and analysed to identify the pollutants and its effect on soil characteristics. The major chemicals in the soil were identified as Ammonia, Chloride, Nitrate, Iron, Nickel, Chromium, Cadmium etc.. Engineering properties of field soil samples show that the chemicals from the leachate of landfill may have effect on the engineering properties of soil. Laboratory experiments were formulated to model the field around an unlined MSW landfill using two different soils subjected to a synthetic leachate. The Maximum change in chemical concentration and engineering property was observed on soil samples at a radial distance of 0.2 m and at a depth of 0.3 m. The pollutant (chemicals) transport pattern through the soil was also studied using synthetic leachate. To establish the effect of pollutants (chemicals) on engineering properties of soil, experiments were conducted on two types soils treated with the synthetic chemicals at four different concentrations. Analyses were conducted after maturing periods of 7, 50, 100 and 150 days. Test soils treated with maximum chemical concentration and matured for 150 days were showing major change in the properties. To visualize the flow of pollutants through soil in a broader sense, the transportation of pollutants through soil was modeled using software ‘Visual MODFLOW’. The actual field data collected for the case study was used to calibrate the modelling and thus simulated the flow pattern of the pollutants through soil around Kalamassery municipal solid waste landfill for an extent of 4 km2. Flow was analysed for a time span of 30 years in which the landfill was closed after 20 years. The concentration of leachate beneath the landfill was observed to be reduced considerably within one year after closure of landfill and within 8 years, it gets lowered to a negligible level. As an environmensstal management measure to control the pollution through leachate, permeable reactive barriers are used as an emerging technology. Here the suitability of locally available materials like coir pith, rice husk and sugar cane bagasse were investigated as reactive media in permeable reactive barrier. The test results illustrates that, among these, coir pith was showing better performance with maximum percentage reduction in concentration of the filtrate. All these three agricultural wastes can be effectively utilized as a reactive material. This research establishes the influence of leachate of municipal solid waste landfill on the engineering properties of soil. The factors such as type of the soil, composition of leachate, infiltration rate, aquifers, ground water table etc., will have a major role on the area of influence zone of the pollutants in a landfill. Software models of the landfill area can be used to predict the extent and the time span of pollution of a landfill, by inputting the accurate field parameters and leachate characteristics. The present study throws light on the role of agro waste materials on the reduction of the pollution in leachate and thus prevents the groundwater and soil from contamination

The influence of shade and organic fertilizer treatments on the physiology and establishment of Theobroma cacao clones

Aims: This experiment aimed to determine whether the soil application of organic fertilizers can help the establishment of cacao and whether shade alters its response to fertilizers. Study Design: The 1.6 ha experiment was conducted over a period of one crop year (between April 2007 and March 2008) at the Cocoa Research Institute of Ghana. It involved four cacao genotypes (T 79/501, PA 150, P 30 [POS] and SCA 6), three shade levels (‘light’, ‘medium’ and ‘heavy’) and two fertilizer treatments (‘no fertilizer’, and ‘140 kg/ha of cacao pod husk ash (CPHA) plus poultry manure at 1,800 kg/ha). The experiment was designed as a split-plot with the cacao genotypes as the main plot factor and shade x fertilizer combinations as the sub-plots. Methodology: Gliricidia sepium and plantains (Musa sapientum) were planted in different arrangements to create the three temporary shade regimes for the cacao. Data were collected on temperature and relative humidity of the shade environments, initial soil nutrients, soil moisture, leaf N, P and K+ contents, survival, photo synthesis and growth of test plants. Results: The genotypes P 30 [POS] and SCA 6 showed lower stomatal conductance under non-limiting conditions. In the rainy seasons, plants under light shade had the highest CO2 assimilation rates. However, in the dry season, plants under increased shade recorded greater photosynthetic rates (P = .03). A significant shade x fertilizer interaction (P = .001) on photosynthesis in the dry season showed that heavier shade increases the benefits that young cacao gets from fertilizer application in that season. Conversely, shade should be reduced during the wet seasons to minimize light limitation to assimilation. Conclusion: Under ideal weather conditions young cacao exhibits genetic variability on stomatal conductance. Also, to optimize plant response to fertilizer application shade must be adjusted taking the prevailing weather condition into account.

Mesoestruturas porosas a partir de materiais naturais

The MCM-41 mesoporous synthesis was done using rice hulls ash and chrysotile as natural alternative silica sources. For the using of these sources, chemical and thermic treatments were done in both materials. After chemical and thermic treatments, these materials were employed on the MCM-41 mesoctructures synthesis. The natural materials treated and employed in the synthesis were characterized by several techniques such as X-ray diffraction, N2 adsorption and desorption, scanning electronic microscopy and thermogravimetric analysis. MCM-41 standart samples synthetized with aerosil 200 commercial sílica were used to evaluation. The formed material from rice hulls ash showed values from BET specific area about 468 m².g-1, N2 adsorption and desorption isotherms and loss mass similar to reference materials. The silica from chrysotile calcined and leached was employed to mesoporous materials synthesis. The BET specific area showed values about 700 m².g-1, N2 adsorption and desorption isotherms type IV and loss mass similar to mesoporous materials. The formed material from calcined and leached chrysotile, without calcination, applied to phenol remotion carried high performance liquid chromatography and evaluated with organophilic clays with different treatments. By the characterization techniques were proved that mesoporous materials with lesser order that reference samples. The material formed from rice hulls ash without the calcination step achieved better adsorption results than organophilic clays

Adição de subprodutos da cinza da casca de café (coffea canephora) em massa cerâmica para porcelanato

To produce porcelain tiles fluxing agents are used in order to obtain a liquid phase during firing. This liquid phase fills the pores decreasing porosity, water absorption and contributes to material densification. In the porcelain tiles industry, feldspar is the main flux material used, with quantities ranging between 35 and 50%. Studies focus on the discovery of materials with flux characteristics that can reduce the consumption of feldspar by porcelain tiles industry. In this context, the coffee husk ashes, a residue obtained when coffee husks are burned to produce heat for the dryers during the processing of the green fruit, have as main chemical constituents potassium, calcium and magnesium, giving them characteristics of fluxing material. Brazil is the largest coffee producer in the world and is responsible for over 30% of the world s production. In this work a physical treatment of coffee husk ash was carried out in order to eliminate the organic matter and, after this, two by-products were obtained: residual wastes R1 and R2. Both residues were added separately as single fluxes and also in association with feldspar in mixtures with raw materials collected in a porcelain industry located in Dias d Ávila-Ba. The addition of these residues aimed to contribute to the reduction of the consumption of feldspar in the production of porcelain tiles. Specimens were produced with dimensions of 60 mm x 20 mm x 6 mm in an uniaxial die with compacting pressure of 45 MPa. The samples were heated to a temperature of 1200 °C, for 8 minutes. Tests were performed to characterize the raw materials by XRF, XRD, particle size analysis, DTA and TGA and, additionally, the results of the physical properties of water absorption, apparent porosity, linear shrinkage, density, dilatometry, flexural strength and SEM of sintered body were analyzed. Additions of less than 8% of the residue R1 contributed to the decrease of porosity, but the mechanical strength of the samples was not satisfactory. Additions of 5% the R2 residue contributed significantly to decrease the water absorption and apparent porosity, and also to increase the mechanical strength. Samples with addition of feldspar associated with the R2 residue, in proportions of 6.7% of R2 and 6.7% of feldspar, led to results of water absorption of 0.12% and mechanical strength of 46 MPa, having parameters normalized to the manufacture of porcelain stoneware tiles

Incorporação de cinzas da casca de café na produção de placas cerâmicas para revestimento

Brazil is the world s leading coffee producer. In 2008, 45.99 million of 60 kg bags of benefited coffee were produced. In the process of improvement 50% is grain and 50% is husk, thus, 1.38 million tons of coffee husk are produced annually. The husk is used as combustible in the drying and improvement ovens in the coffee farms, generating ash as residue. These ashes contain a high concentration of alkaline metals and earth metals, mainly K2O and CaO. This work studies the use of this residue in the ceramic tiles industry, as fluxing agents in substitution to the feldspar. Ten mixtures with equal ratios of clay and kaolin, proceeding from Bahia and the residue (varying from 30 to 5%) were defined and produced in uniaxial tool die of 60x20mm with approximately 5 mm of thickness and 45MPa compacting pressure. The samples were fired in four different temperatures: 1100 °C, 1150 °C, 1185 °C and 1200 °C during 60 minutes and characterized by means of X-ray fluorescence, X-ray diffraction, gravimetric thermal analysis and differential thermal analysis. The results of water absorption, apparent porosity, linear shrinkage, XRD, dilatometry, flexural strength and SEM were also analysed. The test specimen with addition of 10% of ash fired in 1200 °C resulted in 0.18% water absorption and 40.77 MPa flexural strength, being classified as porcelain stoneware tiles according to ABNT, UNI and ISO norms

Enraizamento de estacas semilenhosas de lichieira utilizando ácido indolbutírico

O objetivo deste trabalho foi estudar o enraizamento de estacas semilenhosas de lichieira ( Litchi chinensis Sonn.) da cultivar Bengal, empregando ácido indolbutírico (AIB) e sistema de nebulização intermitente. As estacas apicais foram coletadas nos meses de outubro (Primavera), janeiro (Verão) e abril (Outono), acondicionadas adequadamente e transferidas para uma estufa com nebulização intermitente, onde receberam as aplicações de : 0; 1.000; 2.000; 3.000 e 4.000 mg L-1 de AIB, com imersão da base das estacas, durante 10 segundos, e de 200 mg L-1 de AIB, com imersão das bases por 24 horas, em aeração. em seguida, foram colocadas para enraizar em substrato de vermiculita, com casca de arroz carbonizada, na proporção de 1:1. Após 100 dias, foram obtidos os dados referentes à porcentagem de estacas vivas com folhas, porcentagem de estacas enraizadas por parcela, comprimento médio de raiz por estaca enraizada (cm), número médio de raízes formadas por estaca enraizada, massa média da matéria fresca das raízes (g), massa média da matéria seca das raízes(g). Pelos resultados, concluiu-se que não há necessidade da aplicação do AIB para o enraizamento de estacas de lichieira, cultivar Bengal, e que a melhor época de coleta das mesmas é o verão.

Atividade de enzimas oxidativas do Lentinula edodes em substratos agroindustriais

Basidyomycete Lentinula edodes has its related enzymatic activity mainly on the agribusiness waste kind used as a substrate. The objective of this work was to verify the activity of oxidative enzymes lacase (Lac), lignina peroxidase (LiP) and manganese peroxidase (MnP) of three L. edodes strains, in stationary system, cultivated the 25 degrees C, in the absence of light, in substrates wtih 20% of bran of rice, 1% of CaCO(3) and 79% of rice husk (CA), eucalyptus sawdust (SE), cassava bagasse (BM) and sugarcane bagasse (BC), adjusted to 60% of humidity. The Lac and MnP activities were bigger in eucalyptus sawdust (SE) and sugarcane bagasse (BC). The UP activity was not induced for tested substrates. The rice husk (CA) and cassava bagasse (BM) Substrates, although are not adequate to produce Lac or MnP, can be used as additives to increase the porosity, air availability and easy metabolism polysaccharides.

Efeito de diferentes substratos na produção de mudas de mangabeira (Hancornia speciosa)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Enraizamento de estacas lenhosas de pessegueiro cv. Okinawa em diferentes diâmetros de ramos, substratos e recipientes

O trabalho foi desenvolvido no Departamento de Produção Vegetal - Setor Horticultura da Faculdade de Ciências Agronômicas (FCA) da Universidade Estadual Paulista Júlio de Mesquita Filho (UNESP), Campus de Botucatu (SP) com o objetivo de avaliar a influência de diferentes substratos e tipos de recipientes no potencial de enraizamento de estacas lenhosas de pessegueiro cultivar Okinawa com diferentes diâmetros. As estacas foram tratadas com 2,5g L-1 de ácido indol-butírico. O período de permanência das estacas na casa de vegetação foi de 50 dias. Os tratamentos consistiram de seis substratos: areia, casca de arroz carbonizada, vermiculita, areia + casca de arroz carbonizada, areia + vermiculita e casca de arroz carbonizada + vermiculita, com as misturas na proporção 1:1v/v, três tipos de recipientes: sacos plásticos, bandejas de poliestireno expandido e bandejas plásticas e dois grupos de estacas com diâmetros diferentes: 2 a 6mm e 6 a 10mm. O melhor resultado de enraizamento foi obtido em sacos plásticos com vermiculita independente do diâmetro das estacas.

Desenvolvimento de mudas de bromélia (Neoregelia cruenta (R. Graham) L. B. Smith) cultivadas em diferentes substartos e adubação foliar

As bromélias apresentam formas exóticas com uma grande diversidade de cores e de flores, constituindo importantes espécies para uso em paisagismo e floricultura. em conseqüência disto, são muito comercializadas. Porém, parte das plantas que se encontram no mercado, ainda são provenientes do extrativismo. Esta situação é também reflexo do pequeno número de informações sobre técnicas de propagação e cultivo. Uma das limitações é o desconhecimento do tipo de substrato e adubação adequados ao cultivo destas espécies. Assim, o objetivo deste trabalho foi avaliar o crescimento de bromélias do Neoregelia cruenta, cultivadas em diferentes substratos e adubações foliares através da altura, do número de folhas, da matéria fresca e seca, da parte aérea e das raízes. As mudas utilizadas foram provenientes de cultura de tecidos. Após um período de pré-aclimatização, foram transplantadas para estufa sem nebulização. Os substratos foram constituídos da mistura de diferentes proporções de solo, areia, casca de arroz carbonizada e por um substrato comercial à base de vermiculita. Aos substratos foi aplicada adubação foliar, combinando uréia e sacarose, em intervalos de quinze dias. Os resultados obtidos mostraram que as interações entre os substratos, dose de sacarose e de uréia, não afetaram a altura das mudas e o número de folhas. O uso de sacarose também não influenciou o desenvolvimento das mudas. O substrato comercial à base de vermiculita, independente da aplicação de adubação foliar, proporcionou maior altura das mudas e número de folhas. A aplicação de uréia apresentou efeito linear crescente durante o período avaliado.