"Tecniche di Load Pull attivo a bassa frequenza per la caratterizzazione in banda base di transistori per applicazioni RF"

Una sempre crescente quantità di informazione digitale viene condivisa tra miliardi di dispositivi connessi in ogni angolo del pianeta. Per riuscire a sfruttare una banda più ampia ed aumentare la velocità di trasmissione dei dati, i prossimi standard di telecomunicazioni wireless dovranno adoperare frequenze operative sempre più alte, cercando di rispettare stringenti specifiche in termini di affidabilità ed efficienza energetica. In generale, le prestazioni di un transistor dipenderanno dalle terminazioni a cui esso è collegato. In un setup di caratterizzazione e test, è possibile, tramite un metodo noto come load pull attivo, sintetizzare un determinato valore di impedenza ad uno o più piani di riferimento all'interno di un circuito. Questa strategia si basa in generale sulla manipolazione del rapporto tra onde entranti ed uscenti da un piano di riferimento del dispositivo. Se da una parte tecniche di load pull attivo a banda larga a radiofrequenza hanno ricevuto un notevole interesse sia commerciale che accademico, dall'altra le strategie per la sintesi di impedenze presenti al terminale di alimentazione dell'amplificatore, sono state meno investigate. Questo elaborato si propone di introdurre un algoritmo per il load pull attivo a banda base per amplificatori per applicazioni RF. Dopo un'introduzione sui modelli comportamentali degli amplificatori, è stato considerato il problema degli effetti di memoria. È stata poi descritta la tecnica per l'emulazione di impedenze. Dapprima, è stato considerato il caso lineare. Poi, tramite il design di un amplificatore di potenza per applicazioni a radio frequenza usato come device under test (DUT), sono stati affrontati due esempi in presenza di non linearità, verificando la correttezza della tecnica proposta tramite l'uso di simulazioni.

Bipolar Tribocharging Signal During Friction Force Fluctuations At Metal-insulator Interfaces.

Friction and triboelectrification of materials show a strong correlation during sliding contacts. Friction force fluctuations are always accompanied by two tribocharging events at metal-insulator [e.g., polytetrafluoroethylene (PTFE)] interfaces: injection of charged species from the metal into PTFE followed by the flow of charges from PTFE to the metal surface. Adhesion maps that were obtained by atomic force microscopy (AFM) show that the region of contact increases the pull-off force from 10 to 150 nN, reflecting on a resilient electrostatic adhesion between PTFE and the metallic surface. The reported results suggest that friction and triboelectrification have a common origin that must be associated with the occurrence of strong electrostatic interactions at the interface.

Efeito de 13 semanas de treinamento físico militar sobre a composição corporal e o desempenho físico dos alunos da escola preparatória de cadetes do exército

INTRODUCTION: Armies from all over the world acknowledge the importance of good physical fitness for the performance of military duties. The Military Exercise Training (MET) attempts to provide assistance to this search for better physical fitness and performance. OBJECTIVE: To verifying the effect on the body composition and physical performance of the students at ESPCEX (Military School for Preparation of Army Cadets) after 13 weeks of MET. METHODS: The sample was formed by 287 male students from the ESPCEX, whose average age was 18.33 ±1.26. Such students accomplished a boarding school routine, having defined schedules, meals and activities from which they were only released during the weekends. The MET was accomplished five days a week and it comprised both aerobic and resistance training. Measurement of body mass, height, skinfold (triceps, abdominal and suprailiac) was accomplished during pre and post training periods, and the following tests were performed: 12-minutes-run, oblique sit up, arm push up and pull up. Fat percentage, fat-free body mass and fat body mass were calculated using the anthropometric data based on the Guedes 3 skinfold protocol. RESULTS: Significant reduction in fat body mass, fat percentage and in triceptal and abdominal skinfold, as well as increase in suprailiac skinfold and fat-free body mass was observed when anthropometric and body composition data were compared, during the initial and the final periods of training. Significant improvement also occurred in all prformed physical tests, in which better performance was achieved. CONCLUSION: The acquired data suggest that performance of MET 5 days a week brought significantly improved body composition as well as physical performance

Efeitos de diferentes tamanhos de palmares nos indicadores tecnicos do nado crawl em esforços maximos de 50 e 100m

Universidade Estadual de Campinas . Faculdade de Educação Física

Treinamento fisico militar e aptidão fisica relacionada a saude : estudo a partir de conscritos do Tiro-de-Guerra 02-40 Sorocaba, S.P

Universidade Estadual de Campinas. Faculdade de Educação Física

Indicadores de tendencia secular de variaveis associadas ao crescimento, a composição corporal e ao desempenho motor de crianças de 7 a 14 anos

Universidade Estadual de Campinas . Faculdade de Educação Física

Remo : cargas concentradas de força e sua relação com a alteração de diferentes indicadores funcionais

Universidade Estadual de Campinas . Faculdade de Educação Física

Effect of eugenol-based endodontic sealer on the adhesion of intraradicular posts cemented after different periods

OBJECTIVE: This study evaluated in vitro the influence of an eugenol-based sealer (EndoFill) on the retention of stainless steel prefabricated posts cemented with zinc phosphate and resin-based (Panavia F) cements after different periods of root canal obturation, using the pull-out test. MATERIAL AND METHODS: Sixty upper canines were decoronated and the roots were embedded in resin blocks. The specimens were distributed into 3 groups, according to the period elapsed between canal obturation and post cementation: Group I - immediately; Group II - 72 h and Group III - 4 months. The groups were subdivided according to the type of cement used for post cementation: A - zinc phosphate and B - Panavia F. Following the experimental periods, specimens were subjected to pullout test in an Instron machine with application of tensile force at a crosshead speed of 0.5 mm/min until post dislodgement. The maximum forces required for post removal were recorded (kN) and means were subjected to statistical analysis by 2-way ANOVA and Tukey-Kramer test (α=0.001) RESULTS: There were statistically significant differences (p<0.01) between the posts cemented with zinc phosphate cement (0.2112 kN) and Panavia F (0.0501 kN). However, no statistically significant differences (p>0.05) were found between the three post cementation periods, regardless of the cement. CONCLUSIONS: It was concluded that the eugenol-based sealer influenced the tensile strength of the posts cemented with the resin cement, but had no influence on the time waited between root canal obturation and post space preparation/post cementation.

Bond Strength of Multicomponent White Cast Iron Coatings Applied by HVOF Thermal Spray Process

Multicomponent white cast iron is a new alloy that belongs to system Fe-C-Cr-W-Mo-V, and because of its excellent wear resistance it is used in the manufacture of hot rolling mills rolls. To date, this alloy has been processed by casting, powder metallurgy, and spray forming. The high-velocity oxyfuel process is now also considered for the manufacture of components with this alloy. The effects of substrate, preheating temperature, and coating thickness on bond strength of coatings have been determined. Substrates of AISI 1020 steel and of cast iron with preheating of 150 A degrees C and at room temperature were used to apply coatings with 200 and 400 mu m nominal thickness. The bond strength of coatings was measured with the pull-off test method and the failure mode by scanning electron microscopic analysis. Coatings with thickness of 200 mu m and applied on substrates of AISI 1020 steel with preheating presented bond strength of 87 +/- A 4 MPa.

Endurance in judogi grip strength tests: comparison between elite and non-elite judo players

Background and Study Aim: The ability to develop a strong grip and maintain it during a judo match has become an important element for judo athletes. Therefore, the purpose of this investigation was to examine differences between measurements of maximal isometric time on judogi pull-up, and number of repetitions during dynamic judogi pull-up. Material/Methods: The sample was composed by two groups: 16 high-level judo athletes from the male Brazilian National Team and 12 male state-level judo athletes, with at least one athlete per weight category. The tests were compared through analysis of co-variance (body mass as co-variable), followed by a post-hoc test (Scheffe). Significance level was set at 5%. Results: No difference was found in the isometric test: Brazilian Team: 35 +/- 18s; Regional: 39 +/- 14s. However, the Brazilian Team performed a high number of repetitions (12 +/- 5 rep) compared to regional group (9 +/- 4 rep) during the dynamic grip strength endurance test. Conclusions: Thus, dynamic grip strength endurance seems to be a discriminating variable between judo athletes, probably because judo combat involves many elbow extensions and flexions in order to avoid the opponent`s grip and to subdue them.

An external focus of attention results in greater swimming speed

We examined effects of attentional focus on swimming speed. Participants` task was to swim one length of a pool (16 m) using the front crawl stroke. In Experiment 1, intermediate swimmers were given attentional focus instructions related to the crawl arm stroke or the leg kick, respectively. Participants were instructed to focus on ""pulling your hands back"" or ""pushing the instep down"" (internal focus), or on ""pushing the water back/down"" (external focus), respectively. Swim times were significantly shorter with an external focus. In Experiment 2, a control condition was included. Times were significantly faster in the external focus compared with both the internal focus and control conditions. These findings have implications for enhancing performance in swimming.

Efficacy and safety of concurrent training in systemic sclerosis

Pinto, ALS, Oliveira, NC, Gualano, B, Christmann, RB, Painelli, VS, Artioli, GG, Prado, DML, and Lima, FR. Efficacy and safety of concurrent training in systemic sclerosis. J Strength Cond Res 25(5): 1423-1428, 2011-The optimal training model for patients with systemic sclerosis (SSc) is unknown. In this study, we aimed to investigate the effects of a 12-week combined resistance and aerobic training program (concurrent training) in SSc patients. Eleven patients with no evidence of pulmonary involvement were recruited for the exercise program. Lower and upper limb dynamic strengths (assessed by 1 repetition maximum [1RM] of a leg press and bench press, respectively), isometric strength (assessed by back pull and handgrip tests), balance and mobility (assessed by the timed up-and-go test), muscle function (assessed by the timed-stands test), Rodnan score, digital ulcers, Rayland`s phenomenon, and blood markers of muscle inflammation (creatine kinase and aldolase) were assessed at baseline and after the 12-week program. Exercise training significantly enhanced the 1RM leg press (41%) and 1RM bench press (13%) values and back pull (24%) and handgrip strength (11%). Muscle function was also improved (15%), but balance and mobility were not significantly changed. The time-to-exhaustion was increased (46.5%, p = 0.0004), the heart rate at rest condition was significantly reduced, and the workload and time of exercise at ventilatory thresholds and peak of exercise were increased. However, maximal and submaximal (V)over dotO(2) were unaltered (p > 0.05). The Rodnan score was unchanged, and muscle enzymes remained within normal levels. No change was observed in digital ulcers and Raynaud`s phenomenon. This is the first study to demonstrate that a 12-week concurrent training program is safe and substantially improves muscle strength, function, and aerobic capacity in SSc patients.

Roadmapping for technology push and partnership: A contribution for open innovation environments

There are several tools in the literature that support innovation in organizations. Some of the most cited are the so-called technology roadmapping methods, also known as TRM. However, these methods are designed primarily for organizations that adopt the market pull strategy of technology-product integration. Organizations that adopt the technology push integration strategy are neglected in the literature. Furthermore, with the advent of open innovation, it is possible to note the need to consider the adoption of partnerships in the innovation process. Thus, this study proposes a method of technology roadmapping, identified as method for technology push (MTP), applicable to organizations that adopt the technology push integration strategy, such as SMEs and independent research centers in an open-innovation environment. The method was developed through action-research and was assessed from two analytical standpoints: externally, via a specific literature review on its theoretical contributions, and internally, through the analysis of potential users` perceptions on the feasibility of applying MTP. The results indicate both the unique character of the method and its perceived implementation feasibility. Future research is suggested in order to validate the method in different types of organizations (C) 2011 Elsevier Ltd. All rights reserved.

Lattice to boat house, Cleveland Point House, Cleveland

Lattice behind pull-down blind to boat house.

Neighborhood and Efficiency in Manufacturing in Brazilian Regions: A Spatial Markov Chain Analysis

This paper analyzes the geography of regional competitiveness in manufacturing in Brazil. The authors estimate stochastic frontiers to calculate regional efficiency of representative firms in 137 regions in the period 2000-2006, in four sectors defined by technological intensity. The efficiency results are analyzed using Markov Spatial Transition Matrices to provide insights into the transition of regions between efficiency levels, considering their local spatial context. The results indicate that geography plays an important role in manufacturing competitiveness. In particular, regions with more competitive neighbors are more likely to improve their relative efficiency (pull effect) over time, and regions with less competitive neighbors are more likely to lose relative efficiency (drag effect). The authors find that the pull effect is stronger than the drag effect.