Concrete Pavement Mixture Design and Analysis (MDA): Factors Influencing Drying Shrinkage, TPF-5(205), 2014

This literature review focuses on factors influencing drying shrinkage of concrete. Although the factors are normally interrelated, they can be categorized into three groups: paste quantity, paste quality, and other factors.

Drying rates of Rubi grapes submitted to chemical pretreatments for raisin production

The objective of this work was to determine the most appropriated chemical treatment to be used to dry grapes cv. Rubi for raisin production. Drying curves for convective drying with air at 50ºC, in a tray drier, were obtained for grapes submitted to chemical pretreatments with different concentrations of potassium carbonate and olive oil, and different dipping times, according to factorial designs. Convective drying curves were also obtained for grapes pretreated in aqueous suspensions of soybean lecithin, at varied lecithin concentrations and dipping times. Page model was adjusted to the experimental drying curves, and the calculated drying times showed that the best pretreatment consisted in dipping grapes for 2 minutes in a 5% olive oil and 6% K2CO3 emulsion, at 50ºC, which resulted in a drying time close to that of the pretreatment with 2.5% of olive oil, but with a lower consumption of this substance. In addition, the immersion of grapes in an aqueous suspension of 2% soy lecithin, at 50ºC, for 5 minutes, resulted in a total drying time slightly higher than the most effective pretreatment.

Effect of Oven Heating Time of Asphaltic Concrete on Marshall Stability, MLR-82-02, 1982

It has been observed in the Laboratory that an increase in oven heating time of relatively short duration between mixing and compaction of asphaltic concrete hot mixes can have an effect on the Marshall stability results obtained. The purpose of this short investigation is to determine the effect of oven heating time on the density and stability of hot mixes.

Drying of Ink in Inkjet Printing

Tämän diplomityön tavoitteena oli saada perustietoa tekijöistä, jotka vaikuttavat musteen kuivumiseen erilaisilla paperipinnoilla inkjet tulostuksessa. Tavoitteena oli saada tietoa erilaisista musteista, joita käytetään yleisimmissä inkjet tulostustekniikoissa, miten paperit vaikuttavat musteen kuivumiseen ja minkälaisia menetelmiä on olemassa musteen kuivumistekijöiden määrittämiseen. Lisäksi tarkoituksena oli varmistaa, voidaanko inkjetmusteiden absorptioajan määrittämiseen käytettävää DIGAT-laitetta käyttää määrittämään ja ennustamaan erilaisten musteiden kuivumista erilaisilla paperipinnoilla sekä etsiä korrelaatioita musteen absorptioajan ja teknisten paperiominaisuuksien sekä inkjet tulostuksen laadun välillä. Kirjallisuusosassa tarkasteltiin erilaisia inkjet tulostusmenetelmiä, niissä käytettäviä musteita ja musteiden koostumuksia. Tutkittiin myös paperin ja musteen välisiä vuorovaikutuksia sekä inkjet tulostuksen laatua. Kokeellisessa osassa tutkittiin musteenabsorboitumista paperiin DIGAT-laitteen avulla. kuudella eri musteella. Paperinäytteistä määritettiin teknisiä paperiominaisuuksia sekä ominaisuuksia, jotka liittyvät inkjet tulostuksen laatuun. Inkjet tulostuksen laatua tarkasteltiin tulostamalla testikuva kolmella eri tulostimella, jotka olivat Canon Bubble Jet i950, HP DeskJet Cxi970 ja Epson Stylus C46. Havaittiin, että DIGAT-laite ei sovellu määrittämään musteen absorptioaikoja kiiltäville näytteille.Tässä tutkimuksessa näyte, jonka kiilto oli 65 %, oli liian kiiltävä mitattavaksi DIGAT-laitteella. Lisäksi absorptiomäärityksissä havaittiin, että erilaiset musteet asettuvat erilailla paperin pintaan ja että pigmenttipohjaisella musteella asettumisaika oli kaikista pisin. Musteiden absorptioajat olivat nopeimpia erikoisinkjetpaperilla ja hitaimpia päällystetyillä, tiiviillä papereilla. Musteen absorptioajan ja teknisten paperiominaisuuksien ja inkjet tulostuksen laadun välisiä korrelaatioita oli vaikea havaita. Voidaan sanoa, että tulokset olivat muste- ja printterikohtaisia. Havaittiin vain muutamia teknisiä paperiominaisuuksia, jotka korreloivat hyvin musteen absorboitumisen kanssa. Nämäolivat Gurley-Hill huokoisuus, paperin tuhka- sekä kalsiumkarbonaattipitoisuus ja K&N värinabsorptio. Myöskään inkjet tulostuksen laadun ja musteen absorption välisiä korrelaatioita ei löytynyt kuin muutama; densiteetti, mottling sekä bleeding. Tämän tutkimuksen perusteella voidaan todeta DIGAT-laitteen soveltuvan hyvin kuvaamaan inkjet tulostuksen laatuominaisuuksista densiteettia, mottlingia sekä bleedingiä. DIGAT-laitetta voidaan siis käyttää avuksi ennustettaessa kuivumisaikaa ja sen vaikutusta edellä mainittuihin ominaisuuksiin. Läpipainatusominaisuuksia DIGAT-laitteen avulla ei voida tutkia, sillä ne ovat enemmän riippuvaisia paperin neliömassasta, paksuudesta ja huokoisuudesta kuinmusteen absorptioajasta. Teknisistä paperiominaisuuksista Gurley-Hill huokoisuus, paperin tuhka-sekä CaCO3-pitoisuus ja K&N värinabsorptio kuvaavat hyvin musteen imeytymisaikaa paperiin, kun taas ominaisuudet Cobb, HST ja polaari- sekädispersiokomponentit eivät kuvaa. Näyttää siltä, että testikuva, joka on tällä hetkellä käytössä UPM Tutkimus-keskuksessa, ei sovellu suurtehotulostuksen laadun tarkkailuun. Testikuva toimii hyvin pöytätulostimilla ja perinteisillä kopiopapereilla ja inkjetpapereilla, jotka on tarkoitettu tulostettaviksi hitaasti. Tulostusnopeuden ja musteen kuivumisnopeuden välisiä ilmiöitä seei tuo esille, joten se ei sovellu kuvaamaan suurtehotulostusta.

Characterization and drying of caja bagasse (Spondias mombin L.) in a tray dryer using a factorial planning

The caja (Spondias mombin L.) is used in the manufacture of ice-cream, jams, pulps, beverages being also consumed in natura. One of the most important procedures in food conservation is drying, considering that most fresh fruits contain approximately 80% of water. Food drying is used to obtain two basic aspects: (1) the economic factor; in the shipping and handling of the product; (2) at the manipulation; once dried and grinded, the material is rehydrated, at desirable levels, to formulate a new product as in ice cream, jams, yoghurts and drinks and may also be added to pasta, biscuits and other industrialized products. The aim of this study was to investigate the kinetics of caja bagasse drying in a fixed-bed tray dryer, using central composite factorial planning. The following factors were evaluated: temperature (55, 65 and 75 ºC), dryer inlet air velocity (3.2, 4.6 and 6.0 m.s-1) and cake thickness (0.8, 1.2 and 1.6 cm) where the response of the considered variable was caja bagasse moisture content (b.s.) and the results showed that the main effects and their interactions were significant at a 95% confidence level being the best condition obtained at temperature of 75 ºC, velocity of 6.0 m.s-1 and cake thickness of 0.8 cm.

Nutritional potential of green banana flour obtained by drying in spouted bed

This study evaluated the chemical composition of peeled and unpeeled green banana Cavendish (AAA) flour obtained by drying in spouted bed, aiming at adding nutritional value to food products. The bananas were sliced and crushed to obtain a paste and fed to the spouted bed dryer (12 cm height and T = 80 ºC) in order to obtain flour. The flours obtained were subjected to analysis of moisture, protein, ash, carbohydrates, total starch, resistant starch, fiber. The green banana flours, mainly unpeeled, are good sources of fiber and resistant starch with an average of 21.91g/100g and 68.02g/100g respectively. The protein content was found in an average of 4.76g/100g, being classified as a low biological value protein with lysine as the first limiting amino acid. The results showed that unpeeled green banana flour obtained by spouted bed drying can be a valuable tool to add nutritional value to products in order to increase their non-digestible fraction.

Metsähakkeen jalostusarvon nostaminen eri kuivausmenetelmillä

The thesis was made for Hyötypaperi Oy. To the business activity of the company belongs the recycling of materials and carry out for re-use and the manufacture of solid biofuels and solid recovered fuels. Hyötypaperi Oy delivers forest chips to its partner incineration plants by day and night though the year. The value of the forest chips is based on its percentage of dry material. It is important to dry forest chips well before its storage in piles and delivering to incineration plants. In the thesis was examed the increasing of the degree of refinement of forest chips by different drying methods. In the thesis was examined four different drying methods of the forest chips. The methods were field-, plate-, platform- and channel drying. In the channel drying was used a mechanical blower and the other drying methods were based on the weather conditions. By all drying methods were made test dryings during the summer 2007. In the thesis was examined also the economical profitableness of the field- and channel drying. The last examination in the thesis was measuring of the forest chips’s humidity by humidity measuring equipment of sawn timber during November 2007. The field drying on the surface of asphalt is the only method of drying, which is used by Hyötypaperi Oy in its own production. There do not exist earlier properly examined facts of any drying methods of forest chips, because the drying of forest chips is a new branch. By field- and platform drying achieved lower humidity of forest chips than by plate drying. The object by using the humidity measuring equipment was to be informed of the humidity of forest chips. At present the humidity will find out after 24 hours when the sample of humidity quantity has been dried in the oven. The Lappeenranta University of Technology had the humidity measuring equipment of sawn timber. The values of humidity measured by the equipment from the sample of forest chips were 2 – 9 percent lower than the real values of humidity specified by drying in oven.

Reuse of information for selection of methods and operating conditions for drying of pharmaceutical materials

Drying is a major step in the manufacturing process in pharmaceutical industries, and the selection of dryer and operating conditions are sometimes a bottleneck. In spite of difficulties, the bottlenecks are taken care of with utmost care due to good manufacturing practices (GMP) and industries' image in the global market. The purpose of this work is to research the use of existing knowledge for the selection of dryer and its operating conditions for drying of pharmaceutical materials with the help of methods like case-based reasoning and decision trees to reduce time and expenditure for research. The work consisted of two major parts as follows: Literature survey on the theories of spray dying, case-based reasoning and decision trees; working part includes data acquisition and testing of the models based on existing and upgraded data. Testing resulted in a combination of two models, case-based reasoning and decision trees, leading to more specific results when compared to conventional methods.

Adaptações em forno de microondas doméstico para utilização em laboratório

Domestic microwave oven was modified for laboratory applications. Electronic system was made for controlling magnetron irradiation time. Exhaustion and air circulation systems were installed to clean the internal oven atmosphere during operation. The cavity walls were coated with aluminized thermal paint to avoid chemical corrosion. These modifications allowed the usage of the oven for drying and processes using reflux.

The summer North Atlantic Oscillation in CMIP3 models and related uncertainties in projected summer drying in Europe

This paper discusses uncertainties in model projections of summer drying in the Euro-Mediterranean region related to errors and uncertainties in the simulation of the summer NAO (SNAO). The SNAO is the leading mode of summer SLP variability in the North Atlantic/European sector and modulates precipitation not only in the vicinity of the SLP dipole (northwest Europe) but also in the Mediterranean region. An analysis of CMIP3 models is conducted to determine the extent to which models reproduce the signature of the SNAO and its impact on precipitation and to assess the role of the SNAO in the projected precipitation reductions. Most models correctly simulate the spatial pattern of the SNAO and the dry anomalies in northwest Europe that accompany the positive phase. The models also capture the concurrent wet conditions in the Mediterranean, but the amplitude of this signal is too weak, especially in the east. This error is related to the poor simulation of the upper-level circulation response to a positive SNAO, namely the observed trough over the Balkans that creates potential instability and favors precipitation. The SNAO is generally projected to trend upwards in CMIP3 models, leading to a consistent signal of precipitation reduction in NW Europe, but the intensity of the trend varies greatly across models, resulting in large uncertainties in the magnitude of the projected drying. In the Mediterranean, because the simulated influence of the SNAO is too weak, no precipitation increase occurs even in the presence of a strong SNAO trend, reducing confidence in these projections.

Oven avaus

Ovi avataan ja suljetaan. Ulkoa sisälle.

Oven avaus

Ovi avataan ja suljetaan. Useita oven avauksia. Sisä-ovia. Kolinaa. Viimeinen oven avaus sisältä porttikäytävään.

Oven avaus

Nainen avaa oven ja astuu porraskäytävästä sisään, avaimen kilinää.

Oven avaus

Nariseva ulko-ovi avataan, mennään sisälle. Turku, kirjasto.

Experimentos didáticos envolvendo radiação microondas

Theoretical and practical aspects of the use of microwave-assisted strategies in chemistry are introduced for students using simple and safe experiments employing a domestic oven. Three procedures are proposed for evaluating the distribution of microwave radiation inside the microwave oven cavity: (1) variation of the volume of marshmallows; (2) drying of filter paper wetted with Co(II) solution, and (3) variation of water temperature, after microwave-assisted heating. These experiments establish the position with the highest incidence of microwave radiation in the oven cavity, which was chosen for the synthesis of salicylic acid acetate. This synthesis was performed in 5 min of heating and the yield was around 85%. All experiments can be carried out in a 4 h lab-session using low-cost instrumentation.