Synthesis and characterization of a novel retinylamine analog inhibitor of constitutively active rhodopsin mutants found in patients with autosomal dominant retinitis pigmentosa

Two different mutations of the active-site Lys-296 in rhodopsin, K296E and K296M, have been found to cause autosomal dominant retinitis pigmentosa (ADRP). In vitro studies have shown that both mutations result in constitutive activation of the protein, suggesting that the activated state of the receptor may be responsible for retinal degeneration in patients with these mutations. Previous work has highlighted the potential of retinylamine analogs as active-site directed inactivators of constitutively active mutants of rhodopsin with the idea that these or related compounds might be used therapeutically for cases of ADRP involving mutations of the active-site Lys. Unfortunately, however, amine derivatives of 11-cis-retinal, although highly effective against a K296G mutant of rhodopsin, were without affect on the two naturally occurring ADRP mutants, presumably because of the greater steric bulk of Glu and Met side chains in comparison to Gly. For this reason we synthesized a retinylamine analog one carbon shorter than the parent 11-cis-retinal and show that this compound is indeed an effective inhibitor of both the K296E and K296M mutants. The 11-cis C19 retinylamine analog 1 inhibits constitutive activation of transducin by these mutants and their constitutive phosphorylation by rhodopsin kinase, and it does so in the presence of continuous illumination from room lights.

High-Temperature Perturbation of Starch Synthesis Is Attributable to Inhibition of ADP-Glucose Pyrophosphorylase by Decreased Levels of Glycerate-3-Phosphate in Growing Potato Tubers1

To investigate the short-term effect of elevated temperatures on carbon metabolism in growing potato (Solanum tuberosum L.) tubers, developing tubers were exposed to a range of temperatures between 19°C and 37°C. Incorporation of [14C]glucose (Glc) into starch showed a temperature optimum at 25°C. Increasing the temperature from 23°C or 25°C up to 37°C led to decreased labeling of starch, increased labeling of sucrose (Suc) and intermediates of the respiratory pathway, and increased respiration rates. At elevated temperatures, hexose-phosphate levels were increased, whereas the levels of glycerate-3-phosphate (3PGA) and phosphoenolpyruvate were decreased. There was an increase in pyruvate and malate, and a decrease in isocitrate. The amount of adenine diphosphoglucose (ADPGlc) decreased when tubers were exposed to elevated temperatures. There was a strong correlation between the in vivo levels of 3PGA and ADPGlc in tubers incubated at different temperatures, and the decrease in ADPGlc correlated very well with the decrease in the labeling of starch. In tubers incubated at temperatures above 30°C, the overall activities of Suc synthase and ADPGlc pyrophosphorylase declined slightly, whereas soluble starch synthase and pyruvate kinase remained unchanged. Elevated temperatures led to an activation of Suc phosphate synthase involving a change in its kinetic properties. There was a strong correlation between Suc phosphate synthase activation and the in vivo level of Glc-6-phosphate. It is proposed that elevated temperatures lead to increased rates of respiration, and the resulting decline of 3PGA then inhibits ADPGlc pyrophosphorylase and starch synthesis.

Isolation of an oxygen-sensitive FNR protein of Escherichia coli: interaction at activator and repressor sites of FNR-controlled genes.

The Escherichia coli fnr gene product, FNR, is a DNA binding protein that regulates a large family of genes involved in cellular respiration and carbon metabolism during conditions of anaerobic cell growth. FNR is believed to contain a redox/O2-sensitive element for detecting the anaerobic state. To investigate this process, a fnr mutant that encodes an altered FNR protein with three amino acid substitutions in the N-terminal domain was constructed by site-directed mutagenesis. In vivo, the mutant behaved like a wild-type strain under anaerobic conditions but had a 14-fold elevated level of transcriptional activation of a reporter gene during aerobic cell growth. The altered fur gene was overexpressed in E. coli and the resultant FNR protein was purified to near homogeneity by using anaerobic chromatography procedures. An in vitro Rsa I restriction site protection assay was developed that allowed for the assessment of oxygen-dependent DNA binding of the mutant FNR protein. The FNR protein was purified as a monomer of M(r) 28,000 that contained nonheme iron at 2.05 +/- 0.34 mol of Fe per FNR monomer. In vitro DNase I protection studies were performed to establish the locations of the FNR-binding sites at the narG, narK, dmsA, and hemA promoters that are regulated by either activation or repression of their transcription. The sizes of the DNA footprints are consistent with the binding of two monomers of FNR that protect the symmetrical FNR-recognition sequence TTGAT-nnnnATCAA. Exposure of the FNR protein or protein-DNA complex to air for even short periods of time (approximately 5 min) led to the complete loss of DNA protection at a consensus FNR recognition site. A model whereby the FNR protein exists in the cell as a monomer that assembles on the DNA under anaerobic conditions to form a dimer is discussed.

Oxidação eletroquímica de etanol em temperatura ambiente e intermediária: estudo quantitativo das vias reacionais por espectrometria de massas on-line

Na primeira parte do trabalho, foram investigados materiais ativos para eletro-oxidar etanol e acetaldeído seletivos para a rota C2 (Carbono 2) e, também, ativos para eletro-oxidar hidrogênio molecular, visando a aplicação em células a combustível de hidrogênio indireto. Neste tipo de célula, um processador de combustível externo desidrogena o etanol e os produtos desta reação, contendo H2, acetaldeído e, possivelmente, etanol residual, são direcionados para alimentar o ânodo. Neste sentido, o eletrocatalisador anódico pode ser ativo para a eletro-oxidação de etanol residual, bem como acetaldeído, mas este deve catalisar a reação via C2 com o objetivo de evitar a formação de espécies que envenenam a superfície catalítica (CO ou CHx), ou seja, a ligação C-C deve permanecer intacta. Os eletrocatalisadores bimetálicos foram formados por M/Pt/C (onde M = W, Ru ou Sn) e os produtos reacionais foram analisados por DEMS On-line. Os resultados mostraram que Ru/Pt/C e Sn/Pt/C apresentaram maiores taxas de reação global, no entanto, eles não foram seletivos. Por outro lado, W2/Pt3/C foi mais seletivo para a rota C2, dada a não formação de CH4 e CO2. Além disso, este material também foi ativo e estável para a eletro-oxidação de H2, mesmo na presença de acetaldeído, o que o torna um potencial catalisador para aplicação no ânodo de células a combustível de hidrogênio indireto. Na segunda parte do trabalho, o objetivo foi relacionado com o estudo de eletrocatalisadores seletivos para a rota C1 (Carbono 1). A oxidação eletroquímica do etanol e de seus produtos reacionais foram investigados por DEMS on-line em temperatura ambiente e intermediária (245oC). Para temperatura ambiente, utilizou-se solução aquosa de ácido sulfúrico (H2SO4) e, para temperatura intermediária, utilizou-se ácido sólido (CsH2PO4) como eletrólito. Os eletrocatalisadores investigados foram formados por SnOxRuOx-Pt/C e Pt/C. Em temperatura ambiente, os resultados de polarização potenciodinâmica mostraram uma maior atividade eletrocatalítica para o material SnOxRuOx-Pt/C, com eficiência de corrente para formação de CO2 de 15,6% contra 15,2% para Pt/C, sob condições estagnantes, sem controle por transporte de massa. O stripping de resíduos reacionais, após a eletro-oxidação de etanol bulk, sob condições de fluxo, mostraram o acúmulo de espécies com 1 átomo de carbono (CO e CHx) que causam o bloqueio dos sítios ativos e são oxidadas eletroquimicamente somente em mais altos potenciais (ca. 1,0 V). Por outro lado, as curvas de polarização a 245oC mostraram maiores valores de eficiências de correntes para formação de CO2 (45% para Pt/C em ambos potenciais 0,5 V e 0,8 V contra 36% e 50% para SnOxRuOx-Pt/C em 0,5 V e 0,8 V respectivamente) quando comparado com os valores obtidos em temperatura ambiente, mas com atividades similares para SnOxRuOx-Pt/C e Pt/C. Para ambos os eletrocatalisadores, os estudos de espectrometria de massas a 245oC evidenciaram que as rotas eletroquímicas ocorrem em paralelo com rotas puramente químicas, envolvendo catálise heterogênea, de decomposição do etanol, produzindo H2 e CO2 como produtos majoritários.

Cyclopropane-1,1-dicarboxylate is a slow-, tight-binding inhibitor of rice ketol-acid reductoisomerase

Ketol-acid reductoisomerase (EC 1.1.1.86) catalyses the second reaction in the biosynthesis of the branched-chain amino acids. The reaction catalyzed consists of two stages, the first of which is an alkyl migration from one carbon atom to its neighbour. The likely transition state is therefore a cyclopropane derivative, and cyclopropane-1,1-dicarboxylate(CPD) has been reported to inhibit the Escherichia coli enzyme. In addition, this compound causes the accumulation of the substrate of ketol-acid reductoisomerase in plants. Here, we investigate the inhibition of the purified rice enzyme. The cDNA was cloned, and the recombinant protein was expressed in E. coli, purified and characterized kinetically. The purified enzyme is strongly inhibited by cyclopropane-1,1-dicarboxylate, with an inhibition constant of 90 nM. The inhibition is time-dependent and this is due to the low rate constants for formation (2.63 X 10(5) M-1 min(-1)) and dissociation (2.37 x 10(-2) min(-1)) of the enzyme-inhibitor complex. Other cyclopropane derivatives are much weaker inhibitors while dimethylmalonate is moderately effective. (c) 2004 Elsevier Ireland Ltd. All rights reserved.

An evaluation of steels subjected to rock bolt SCC conditions

In order to understand the metallurgical influences on Rock Bolt SCC, an evaluation has been carried out on carbon, carbon + manganese, alloy and microalloyed steels subjected to the conditions previously identified as producing laboratory SCC similar to that observed for rock bolts in service. The approach has been to use the LIST test (Linearly increasing stress test) for samples exposed to a dilute pH 2.1-sulphate solution, as per our prior studies. SCC was evaluated from the decrease in tensile strength, ductility and fractography as revealed by SEM observation. A range of SCC susceptibilities was observed. Ten of these steels showed SCC, however there was no SCC for one carbon, two carbon + manganese and two alloy steels.

The effect of thermochemical treatment on the fatigue properties of alloy steels

The effect of thermochemical treatment namely carburising on the fatigue behaviour of one carbon and two alloy steels has been studied in rotating and unidirectional bending. The effect of carbon profile on the unidirect¬ional bending fatigue strength of 63SA14 was assessed, and it was found that single stage carburising with a surface carbon content of 0.8% has resulted in a higher fatigue strength than other types of carbon profiles. Residual stresses and other metallurgical variables arising from different carbon profiles, were also considered. The highest compressive stresses h~e resulted from boost-diffuse-carburising. On the other hand surface decarburisation was associated with tensile residual stresses and a reduced fatigue strength. Retained austenite was found to be detrimental in unidirectional bending fatigue; however its presence in carburised 83SAIS did not seem to influence the rotating bending fatigue strength. Carbide particles in globular and/or intergranular form were detrimental to compressive residual stresses; the unidirectional bending fatigue strength is markedly lowered. The highest fatigue strength was accomplished by vacuum carburising. The absence of internal oxidation was the key factor in the increased fatigue strength; the presence of uniformly distributed fine carbide particles did not upset the superior fatigue strength of vacuum carburised pieces. The effect of mean stress on the fatigue strength of carburised 63SA14 was studied. Increasing the mean stress as would be expected resulted in a decreased fatigue strength. Carburisation showed its advantages at low mean stress, but at high mean stress it offers little advantage over the uncarburised hardened conditions. Notch effect was also studied in unidirectional bending of carburised 080MlS. The general trend showed that the fatigue strength decreases with increasing the stress concentration factor. But different carburising conditions have different effect on notch sensitivity.

Modes of sapropel formation in the eastern Mediterranean: some constraints based on pyrite properties

Pyrite formation within and directly below sapropels in the eastern Mediterranean was governed by the relative rates of sulphide production and Fe liberation and supply to the organic-rich layers. At times of relatively high [SO4]2- reduction, sulphide could diffuse downward from the sapropel and formed pyrite in underlying sediments. The sources of Fe for pyrite formation comprised detrital Fe and diagenetically liberated Fe(II) from sapropel-underlying sediments. In organic-rich sapropels, input of Fe from the water column via Fe sulphide formation in the water may have been important as well. Rapid pyrite formation at high saturation levels resulted in the formation of framboidal pyrite within the sapropels, whereas below the sapropels slow euhedral pyrite formation at low saturation levels occurred. d34S values of pyrite are -33 per mil to -50 per mil. Below the sapropels d34S is lower than within the sapropels, as a result of increased sulphide re-oxidation at times of relatively high sulphide production and concentration when sulphide could escape from the sediment. The percentage of initially formed sulphide that was re-oxidized was estimated from organic carbon fluxes and burial efficiencies in the sediment. It ranges from 34% to 80%, varying significantly between sapropels. Increased palaeoproductivity as well as enhanced preservation contributed to magnified accumulation of organic matter in sapropels.

Proteômica diferencial da Chromobacterium violaceum em resposta ao estresse oxidativo induzido por peróxido de hidrogênio

The β-proteobacterium Chromobacterium violaceum is a Gram-negative, free-living, saprophytic and opportunistic pathogen that inhabits tropical and subtropical ecosystems among them, in soil and water of the Amazon. It has great biotechnological potential, and because of this potential, its genome was completely sequenced in 2003. Genome analysis showed that this bacterium has several genes with functions related to the ability to survive under different kinds of environmental stresses. In order to understand the physiological response of C. violaceum under oxidative stress, we applied the tool of shotgun proteomics. Thus, colonies of C. violaceum ATCC 12472 were grown in the presence and absence of 8 mM H2O2 for two hours, total proteins were extracted from bacteria, subjected to SDS-PAGE, stained and hydrolysed. The tryptic peptides generated were subjected to a linear-liquid chromatography (LC) followed by mass spectrometer (LTQ-XL-Orbitrap) to obtain quantitative and qualitative data. A shotgun proteomics allows to compare directly in complex samples, differential expression of proteins and found that in C. Violaceum, 131 proteins are expressed exclusively in the control condition, 177 proteins began to be expressed under oxidative stress and 1175 proteins have expression in both conditions. The results showed that, under the condition of oxidative stress, this bacterium changes its metabolism by increasing the expression of proteins capable of combating oxidative stress and decreasing the expression of proteins related processes bacterial growth and catabolism (transcription, translation, carbon metabolism and fatty acids). A tool with of proteomics as an approach of integrative biology provided an overview of the metabolic pathways involved in the response of C. violaceum to oxidative stress, as well as significantly amplified understanding physiological response to environmental stress. Biochemical and "in silico" assays with the hypothetical ORF CV_0868 found that this is part of an operon. Phylogenetic analysis of superoxide dismutase, protein belonging to the operon also showed that the gene is duplicated in genome of C. violaceum and the second copy was acquired through a horizontal transfer event. Possibly, not only the SOD gene but also all genes comprising this operon were obtained in the same manner. It was concluded that C. violaceum has complex, efficient and versatile mechanisms in oxidative stress response

Allocation du carbone et métabolisme azoté chez l'haptophyte Tisochrysis lutea

The aim of this thesis is to improve knowledge on mechanisms involved in the response to nitrogen limitation and in lipid accumulation in the microalgae haptophyte Tisochrysis lutea. The wild type strain and a lipid accumulating mutant strain were grown under different nitrogen limitation and starvation and analyzed by functional genomics. Four genes of high-affinity nitrate/nitrite transporter (Nrt2) were identified and characterized to reveal the mechanisms involved in mineral absorption in this species. Transcriptomes of both strains were sequenced and proteins affected by nitrogen starvation and differentially expressed between the two strains were identified. We so identified the functions regulated by nitrogen deficiency and potentially involved in the accumulation of storage lipids. The responses of both strains to thin variations of nitrogen limitation were studied. The results of high-throughput proteomic analyzes suggest that the lipid-accumulation in the mutant strain is the result of carbon metabolism impacted overall, this spurred on signaling mechanisms. Two proteins have been studied since probably involved in carbon and nitrogen remobilization from amino acids catabolism during nitrogen limitation. This work increases knowledge on haptophytes, and brings assumptions on metabolic key involved in nitrogen limitation and carbon allocation in microalgae.

Études de la réponse du métabolisme énergétique à la carence en fer dans les cultures cellulaires de Solanum tuberosum

Le fer est un micronutriment important pour la croissance et le développement des plantes. Il agit comme cofacteur pour plusieurs enzymes et il est important pour des processus tels que la photosynthèse et la respiration. Souvent, le Fe dans le sol n’est pas bio-disponible pour la plante. Les plantes ont développé des stratégies pour solubiliser le Fe du sol pour le rendre disponible et assimilable pour elles. Il y a deux stratégies, la première est caractéristique des dicotylédones et la seconde est caractéristique des monocotylédones. Le modèle utilisé dans cette étude est une culture cellulaire de Solanum tuberosum. Une partie de la recherche effectuée a permis la mesure d’activité et d’expression relative de certaines enzymes impliquées dans le métabolisme énergétique et la fourniture de précurseurs pour la synthèse d’ADN : la Nucléoside diphosphate kinase, la Ribonucléotide reductase, la Glucose 6-phosphate déshydrogénase et la 6-Phosphogluconate déshydrogénase dans les cellules en présence ou en absence de Fe. Chez certains organismes, la déficience en Fe est associée à une perte de croissance qui est souvent liée à une diminution de la synthèse d’ADN. Chez les cultures de cellules de S. tuberosum, les résultats indiquent que la différence de biomasse observée entre les traitements n’est pas due à une variation de l’activité ou l’expression relative d’une de ces enzymes. En effet, aucune variation significative n’a été détectée entre les traitements (+/- Fe) pour l’activité ni l’expression relative de ces enzymes. Une autre partie de la recherche a permis d’évaluer l’activité des voies métaboliques impliquées dans la stratégie 1 utilisée par S. tuberosum. Cette stratégie consomme des métabolites énergétiques: de l’ATP pour solubiliser le Fe et du pouvoir réducteur (NAD(P)H), pour réduire le Fe3+ en Fe2+. Des études de flux métaboliques ont été faites afin d’étudier les remaniements du métabolisme carboné en déficience en Fe chez S. tuberosum. Ces études ont démontré une baisse du régime dans les différentes voies du métabolisme énergétique dans les cellules déficientes en Fe, notamment dans le flux glycolytique et le flux de C à travers la phosphoenolpyruvate carboxylase. En déficience de Fe il y aurait donc une dépression du métabolisme chez S. tuberosum qui permettrait à la cellule de ralentir son métabolisme pour maintenir sa vitalité. En plus des flux, les niveaux de pyridines nucléotides ont été mesurés puisque ceux-ci servent à réduire le Fe dans la stratégie 1. Les résultats démontrent des niveaux élevés des formes réduites de ces métabolites en déficience de Fe. L’ensemble des résultats obtenus indiquent qu’en déficience de Fe, il y a une baisse du métabolisme permettant à la cellule de s’adapter et survivre au stress.

Études de la réponse du métabolisme énergétique à la carence en fer dans les cultures cellulaires de Solanum tuberosum

Le fer est un micronutriment important pour la croissance et le développement des plantes. Il agit comme cofacteur pour plusieurs enzymes et il est important pour des processus tels que la photosynthèse et la respiration. Souvent, le Fe dans le sol n’est pas bio-disponible pour la plante. Les plantes ont développé des stratégies pour solubiliser le Fe du sol pour le rendre disponible et assimilable pour elles. Il y a deux stratégies, la première est caractéristique des dicotylédones et la seconde est caractéristique des monocotylédones. Le modèle utilisé dans cette étude est une culture cellulaire de Solanum tuberosum. Une partie de la recherche effectuée a permis la mesure d’activité et d’expression relative de certaines enzymes impliquées dans le métabolisme énergétique et la fourniture de précurseurs pour la synthèse d’ADN : la Nucléoside diphosphate kinase, la Ribonucléotide reductase, la Glucose 6-phosphate déshydrogénase et la 6-Phosphogluconate déshydrogénase dans les cellules en présence ou en absence de Fe. Chez certains organismes, la déficience en Fe est associée à une perte de croissance qui est souvent liée à une diminution de la synthèse d’ADN. Chez les cultures de cellules de S. tuberosum, les résultats indiquent que la différence de biomasse observée entre les traitements n’est pas due à une variation de l’activité ou l’expression relative d’une de ces enzymes. En effet, aucune variation significative n’a été détectée entre les traitements (+/- Fe) pour l’activité ni l’expression relative de ces enzymes. Une autre partie de la recherche a permis d’évaluer l’activité des voies métaboliques impliquées dans la stratégie 1 utilisée par S. tuberosum. Cette stratégie consomme des métabolites énergétiques: de l’ATP pour solubiliser le Fe et du pouvoir réducteur (NAD(P)H), pour réduire le Fe3+ en Fe2+. Des études de flux métaboliques ont été faites afin d’étudier les remaniements du métabolisme carboné en déficience en Fe chez S. tuberosum. Ces études ont démontré une baisse du régime dans les différentes voies du métabolisme énergétique dans les cellules déficientes en Fe, notamment dans le flux glycolytique et le flux de C à travers la phosphoenolpyruvate carboxylase. En déficience de Fe il y aurait donc une dépression du métabolisme chez S. tuberosum qui permettrait à la cellule de ralentir son métabolisme pour maintenir sa vitalité. En plus des flux, les niveaux de pyridines nucléotides ont été mesurés puisque ceux-ci servent à réduire le Fe dans la stratégie 1. Les résultats démontrent des niveaux élevés des formes réduites de ces métabolites en déficience de Fe. L’ensemble des résultats obtenus indiquent qu’en déficience de Fe, il y a une baisse du métabolisme permettant à la cellule de s’adapter et survivre au stress.