Parametric analog signal amplification applied to nanoscale cmos wireless digital transceivers

Thesis presented in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the subject of Electrical and Computer Engineering by the Universidade Nova de Lisboa,Faculdade de Ciências e Tecnologia

Design of a CMOS amplifier for breast cancer detection

A transimpedance amplifier (TIA) is used, in radiation detectors like the positron emission tomography(PET), to transform the current pulse produced by a photo-sensitive device into an output voltage pulse with a desired amplitude and shape. The TIA must have the lowest noise possible to maximize the output. To achieve a low noise, a circuit topology is proposed where an auxiliary path is added to the feedback TIA input, In this auxiliary path a differential transconductance block is used to transform the node voltage in to a current, this current is then converted to a voltage pulse by a second feedback TIA complementary to the first one, with the same amplitude but 180º out of phase with the first feedback TIA. With this circuit the input signal of the TIA appears differential at the output, this is used to try an reduced the circuit noise. The circuit is tested with two different devices, the Avalanche photodiodes (APD) and the Silicon photomultiplier (SIPMs). From the simulations we find that when using s SIPM with Rx=20kΩ and Cx=50fF the signal to noise ratio is increased from 59 when using only one feedback TIA to 68.3 when we use an auxiliary path in conjunction with the feedback TIA. This values where achieved with a total power consumption of 4.82mv. While the signal to noise ratio in the case of the SIPM is increased with some penalty in power consumption.

Non-gyrator type active inductors

Modern CMOS radio frequency (RF) Receivers have enabled efficient and increasing applications. The main requirement is to have system in a single chip, in order to minimize area and cost. For the purpose it is required the development of inductorless circuits for the key blocks of an RF receiver. Examples of this key blocks are RC oscillators, RF band pass filters, and Low Noise Amplifiers. The present dissertation presents an inductorless wideband MOSFET-only RF Non-Gyrator Type of Active Inductors with low area, low cost, and very low power, capable of covering the whole WMTS, and ISM, band and intended for biomedical applications. The proposed circuit is based on a floating capacitor connected between two controlled current sources. The first current source, which is controlled by the circuit input voltage, has two objectives: supply current to the capacitor (

Disseny, fabricació i caracterització d'amplificadors de baix soroll per instrumentació

Aquest projecte consisteix en l’estudi, disseny i fabricació d’un amplificador de baix soroll per instrumentació, el qual es basarà en uns requisits de guany, ample de banda i de mides a complir. Un vegada vistos els requisits i fet un estudi previ de la situació, el primer pas serà realitzar el disseny principal de l’amplificador, el qual s’anirà millorant a mesura que avanci el projecte. Un cop dissenyat i avaluat el circuit amb el software ADS, el següent pas serà intentar fer un model de layout, el qual serà fabricat i analitzat, per tal d'intentar aconseguir el resultat esperat de les especificacions. Finalment, es detallaran les conclusions a les quals s’ha arribat desprès d’haver realitzat aquest projecte.

Disseny i implementació d'una etapa d'acondicionament per a mesures de conductivitat realitzades amb un microscopi de forces atòmiques

En aquest treball, s’ha dissenyat un mòdul d’acondicionament a fi de millorar les mesures de conductivitat realitzades amb un AFM (Microscopi de Forces Atòmiques). L’equip actual disposa d’un preamplificador de baix soroll amb un guany de 10 10V/A. Donat que els corrents que es pretenen mesurar són extremadament petits (~pA), s’ha dissenyat un filtre per eliminar diferents fonts de soroll, com ara el soroll que introdueix la xarxa elèctrica a 50Hz. Es pretén reduir aquesta component freqüencial un factor mínim de 10 (20dB). També s’ha afegit un filtre passa baixos per eliminar els soroll que es troba fora de l’amplada de banda del preamplificador. S’ha introduït una etapa d’amplificació de guany variable: 1, 10 i 100 per augmentar la flexibilitat de l’equip i finalment també s’ha dissenyat una etapa per eliminar la tensió d’offset d’aquest amplificador. L’abast del treball anirà des del disseny fins la implementació final sobre una placa PCB.

Microcontroller-driven fluid-injection system for atomic force microscopy.

We present a programmable microcontroller-driven injection system for the exchange of imaging medium during atomic force microscopy. Using this low-noise system, high-resolution imaging can be performed during this process of injection without disturbance. This latter circumstance was exemplified by the online imaging of conformational changes in DNA molecules during the injection of anticancer drug into the fluid chamber.

Ympäristövaikutusten velvoitetarkkailun tulosten epävarmuuden arviointi

Tämä diplomityö tehtiin Neste Oil Oyj:n Kehittäminen ja Laboratoriot yksikön HSE-palveluille. Työn tavoitteena oli arvioida Neste Oilin ympäristövaikutusten velvoitetarkkailujen mittaustulosten epävarmuutta. Tarkastelu koski ilmanlaadun SO2-, NO2-, TRS- sekä O3-mittauksia, ympäristömelumittauksia sekä pohjavesinäytteenottoa. Ympäristönsuojelulaki (86/2000) velvoittaa tuotantolaitoksia selvittämään toimintansa ympäristövaikutukset. Myös esimerkiksi akkreditoitaessa menetelmiä mittausepävarmuus on tunnettava. On arvioitu, että tulevaisuudessa direktiivit tulevat tiukentamaan päästöraja-arvoja ja mittausepävarmuuden käsite tulee käyttöön kaikilla ympäristösektoreilla.Tässä työssä ilmanlaadun mittausepävarmuus arvioitiin vertaamalla Neste Oilin mittaustuloksia Ilmatieteenlaitoksen vertailumittausten ja kalibrointien tuloksiin. Ympäristömelun mittausepävarmuus arvioitiin Ympäristöministeriön ympäristömelunmittausohjeen (1/1995)mukai-sesti. Pohjavesinäytteenoton mittausepävarmuus arvioitiin laskemalla haitta-aineiden ajallisen vaihtelun, näytteenottomenetelmien, näytteiden kuljetuksenja säilytyksen aiheuttaman kontaminaation sekä analyysivaiheen epävarmuustekijöiden yhdistetty mittausepävarmuus. Tarkastelussa todettiin, että ilmanlaadunmittaustulokset eivät poikenneet merkittävästi vertai-lumittausten ja kalibrointien tuloksista. Menetelmien laajennetuksi mittausepävarmuudeksi saatiin 6-8 %. Ympäristömelun mittausepävarmuus vastasi ympäristömelunmittausohjeessa esitettyjä arvoja ja vaihtelivat 2-10 dB:n välillä, riippuen mittausetäisyydestä ja mittauskertojen lukumäärästä. Pohjavesinäytteenoton mittausepävarmuudelle ei ole asetettu laatutavoitteita. Tässä tarkastelussa pohjavesinäytteenoton mittausepävarmuudeksi saatiin 33 %.

Jäähdytysjärjestelmän vaikutus kiinteistön elinkaaren aikaisiin tuottoihin

Ilmastoinnin jäähdytys yleistyy toimisto- ja hotellikiinteistöissä jatkuvasti. Perinteinen tapa tuottaa jäähdytysenergia on kiinteistökohtainen vedenjäähdytysjärjestelmä. Helsingissä on ollut vuodesta 2000 lähtien mahdollista liittyä Helsingin energian kaukojäähdytysverkostoon. Jäähdytysjärjestelmien ominaisuudet poikkeavat toisistaan ja niistä aiheutuu kiinteistönomistajalle erilaisia kustannuksia. Kiinteistöstä saataviin tuottoihin vaikuttaa kustannusten lisäksi vuokralaisen tyytyväisyys. Tämän vuoksi työssä selvitettiin vuokralaisen tarpeet jäähdytysjärjestelmälle haastattelemalla vuokralaisen edustajia. Tässä diplomityössä vertaillaan kaukojäähdytyksen ja kiinteistökohtaisen jäähdytysjärjestelmän kustannuksia, sekä vaikutuksia kiinteistön elinkaarituottoihin kiinteistönomistajan näkökulmasta. Kerättyjen kustannusten perusteella suoritetaan elinkaarikustannuslaskenta GaBi-ohjelmalla. Vuokralaisen tarpeista jäähdytysjärjestelmälle tunnistetaan olennaisiksi toimintavarmuus, ympäristöystävällisyys sekä hiljainen äänitaso. Nämä ovat lisäarvotekijöitä, joille työssä määritetään painoarvo ja jotka huomioidaan laskennassa. Diplomityö osoitti kaukojäähdytyksen kannattavaksi vaihtoehdoksi kiinteistökohtaiselle järjestelmälle, kun huomioidaan hankinta- ja käyttökustannusten lisäksi asennustöiden, käyttöönoton, huollon ja kunnossapidon sekä loppusijoituksen kustannukset. Myös valikoituneet lisäarvotekijät puoltavat kaukojäähdytystä ja niiden kompensointi lisää kiinteistökohtaisen järjestelmän kustannuksia.

Paperitehtaan melukartoitus

Tässä diplomityössä on selvitetty Stora Enso Publication Papers Oy Ltd:n Summan tehtaiden ympäristömelun leviämistä tehtaiden ympärillä oleviin häiriintyviin kohteisiin. Ympäristömelua tutkittiin ympäristömelumittauksilla ja mallintamalla SoundPLAN –ohjelmalla. Työssä on ympäristömelun lisäksi tarkastelu työsuojelumielessä Summan tehtaiden voimalaitoksen melua. Työssä selvitettiin Summan tehtaiden merkittävimpien äänilähteiden äänitehotasot. Maastotietojen ja äänitehotasojen perusteella luotiin melumallit koko tehtaalle ja melua tuottaville osastoille. Melumallien avulla saatiin selville, miten melu leviää ympäristöön. Suurimpiin melulähteisiin, kuorimoon ja PK2:n ilmastointikoneisiin, laadittiin meluntorjuntaehdotukset ja tarkasteltiin uusien mallien avulla toimenpiteiden vaikutusta melun leviämiseen. Tulosten perusteella voidaan todeta, että Summan tehtaiden ympäristömelu ei ylitä lupa-arvoja häiriintyvissä kohteissa. Summan tehtaiden voimalaitoksella suoritettiin annosmelumittaukset ja laadittiin meluntorjuntaohjelma. Meluntorjuntaohjelmassa selvitettiin melun syyt, esitettiin meluntorjuntatoimenpiteitä ja niiden toteuttamissuunnitelma sekä ohjelman uusimisajankohta.

Hyperfine interactions in the new Fe-based superconducting structures and related magnetic phases

This thesis is devoted to the study of the hyperfine properties in iron-based superconductors and the synthesis of these compounds and related phases. During this work polycrystalline chalcogenide samples with stoichiometry 1:1 (FeTe1-χSχ, FeSe1-x) and pnictide samples with stoichiometry 1:2:2 (BaFe2(As1-χPχ)2, EuFe2(As1-x Px)2) were synthesized by solid-state reaction methods in vacuum and in a protecting Ar atmosphere. In several cases post-annealing in oxygen atmosphere was employed. The purity and superconducting properties of the obtained samples were checked with X-ray diffraction, SQUID and resistivity measurements. For studies of the magnetic properties of the investigated samples Mössbauer spectroscopy was used. Using low-temperature measurements around Tc and various values of the source velocity the hyperfine interactions were obtained and the magnetic and structural properties in the normal and superconducting states could be studied. Mössbauer measurements together with XRD characterization were also used for the detection of impurity phases. DFT calculations were used for the theoretical study of Mössbauer parameters for pnictide-based ᴻsamples BaFe2(As1-xPx)2 and EuFe2(As1-xPx)2.

Cost Reduction of Permanent Magnet Synchronous Machines

Electrical machine drives are the most electrical energy-consuming systems worldwide. The largest proportion of drives is found in industrial applications. There are, however many other applications that are also based on the use of electrical machines, because they have a relatively high efficiency, a low noise level, and do not produce local pollution. Electrical machines can be classified into several categories. One of the most commonly used electrical machine types (especially in the industry) is induction motors, also known as asynchronous machines. They have a mature production process and a robust rotor construction. However, in the world pursuing higher energy efficiency with reasonable investments not every application receives the advantage of using this type of motor drives. The main drawback of induction motors is the fact that they need slipcaused and thus loss-generating current in the rotor, and additional stator current for magnetic field production along with the torque-producing current. This can reduce the electric motor drive efficiency, especially in low-speed, low-power applications. Often, when high torque density is required together with low losses, it is desirable to apply permanent magnet technology, because in this case there is no need to use current to produce the basic excitation of the machine. This promotes the effectiveness of copper use in the stator, and further, there is no rotor current in these machines. Again, if permanent magnets with a high remanent flux density are used, the air gap flux density can be higher than in conventional induction motors. These advantages have raised the popularity of PMSMs in some challenging applications, such as hybrid electric vehicles (HEV), wind turbines, and home appliances. Usually, a correctly designed PMSM has a higher efficiency and consequently lower losses than its induction machine counterparts. Therefore, the use of these electrical machines reduces the energy consumption of the whole system to some extent, which can provide good motivation to apply permanent magnet technology to electrical machines. However, the cost of high performance rare earth permanent magnets in these machines may not be affordable in many industrial applications, because the tight competition between the manufacturers dictates the rules of low-cost and highly robust solutions, where asynchronous machines seem to be more feasible at the moment. Two main electromagnetic components of an electrical machine are the stator and the rotor. In the case of a conventional radial flux PMSM, the stator contains magnetic circuit lamination and stator winding, and the rotor consists of rotor steel (laminated or solid) and permanent magnets. The lamination itself does not significantly influence the total cost of the machine, even though it can considerably increase the construction complexity, as it requires a special assembly arrangement. However, thin metal sheet processing methods are very effective and economically feasible. Therefore, the cost of the machine is mainly affected by the stator winding and the permanent magnets. The work proposed in this doctoral dissertation comprises a description and analysis of two approaches of PMSM cost reduction: one on the rotor side and the other on the stator side. The first approach on the rotor side includes the use of low-cost and abundant ferrite magnets together with a tooth-coil winding topology and an outer rotor construction. The second approach on the stator side exploits the use of a modular stator structure instead of a monolithic one. PMSMs with the proposed structures were thoroughly analysed by finite element method based tools (FEM). It was found out that by implementing the described principles, some favourable characteristics of the machine (mainly concerning the machine size) will inevitable be compromised. However, the main target of the proposed approaches is not to compete with conventional rare earth PMSMs, but to reduce the price at which they can be implemented in industrial applications, keeping their dimensions at the same level or lower than those of a typical electrical machine used in the industry at the moment. The measurement results of the prototypes show that the main performance characteristics of these machines are at an acceptable level. It is shown that with certain specific actions it is possible to achieve a desirable efficiency level of the machine with the proposed cost reduction methods.

Set-up and evaluation of a mid-infrared reflectometer and investigation of the optical properties of doped tin telluride

A system comprised of a Bomem interferometer and a LT3-110 Heli-Tran cryostat was set up to measure the reflectance of materials in the mid-infrared spectral region. Several tests were conducted to ensure the consistency and reliability of the system. Silicon and Chromium, two materials with well known optical properties were measured to test the accuracy of the system, and the results were found to be in good agreement with the literature. Reflectance measurements on pure SnTe and several Pb and Mn-doped alloys were carried out. These materials were chosen because they exhibit a strong plasma edge in the mid infrared region. The optical conductivity and several related optical parameters were calculated from the measured reflectance. Very low temperature measurements were carried out in the far-infrared on Sn9SMn2Te, and the results are indicative of a spin glass phase at 0.8 K. Resistivity measurements were made at room temperature. The resistivity values were found, as expected, to decrease with increasing carrier concentration and to increase with increasing manganese concentration.

Prevalencia de los síntomas otorrinolaringológicos y factores asociados en los trabajadores de una central de llamadas en la ciudad de Bogotá Colombia

La industria de las centrales de llamadas es uno de los sectores de más rápido crecimiento en el mundo desarrollado, gracias a los avances tecnológicos han permitido su uso cada vez más generalizado desarrollando servicios integrales que son accesibles las 24 horas del día. Los operadores telefónicos o tele-operadores de esta industria se ven enfrentados a jornadas laborales en las que se exponen al uso constante de la voz, utilización permanente de auriculares de comunicación, confinamiento en estaciones de trabajo delimitadas pero no aisladas; aumentando así la prevalencia de síntomas como los otorrinolaringológicos. Este estudio tiene como objeto identificar la prevalencia de síntomas otorrinolaringológicos dados por alteraciones de la voz, compromiso auditivo y síntomas de la vía respiratoria superior durante la jornada laboral de los trabajadores de una central de llamadas de una prestigiosa empresa aseguradora de la ciudad de Bogotá Colombia, así como también identificar la asociación de factores demográficos organizacionales y biológicos con los síntomas otorrinolaringológicos y analizar el medio ambiente laboral de dicha empresa y la relación de los síntomas otorrinolaringológicos con mediciones de ruido, temperatura y humedad. La población estudiada fue de 81 tele operadores de los cuales 61 (75.3%) fueron mujeres, se evidencio que las enfermedades respiratorias altas tienen una prevalencia del 36%, también se reporto una prevalencia del 85% (69) tele operadores reportaron por lo menos un síntoma de voz y solo 12 tele operadores 15% no reportaron ningún síntoma. En cuanto a la hipoacusia solo 5 (6.2%) reportaron disminución de la agudeza auditiva

Perfil de la exposición ocupacional a ruido en procesos de producción de cemento en Colombia (2010 - 2015)

La exposición a ruido se considera uno de los principales factores de riesgo involucrados en la génesis de hipoacusia neurosensorial, produciendo deterioro en la calidad de vida de la población trabajadora y pérdidas económicas en las empresas. Se considera que los sectores económicos más expuestos a este factor de riesgo son la industria manufacturera, la construcción, las refinerías de petróleo y las centrales hidroeléctricas. El presente estudio de corte transversal pretende establecer el perfil de exposición ocupacional a ruido en procesos de producción de cemento en Colombia, mediante el análisis de 458 mediciones higiénicas personales de ruido realizadas entre los años 2010 y 2015. En la definición de los grupos de exposición similar se identificaron y describieron las actividades funcionales de la población expuesta, cuyos resultados se evaluaron teniendo como valor de referencia 85 dBA, propuesto por la guía TLV-TWA de la ACGIH (American Conference of Governmental Industrial Hygienists) del 2014. Los resultados del estudio permitieron conocer el perfil de exposición a ruido en los procesos de producción de cemento, en donde se identificaron mayores condiciones de riesgo en los GES Producción, Mina y Mecánicos de Planta, con valores de exposición que exceden el límite permisible establecido por la ACGIH; datos que resultan indispensables para la formulación de medidas de seguimiento, vigilancia y control.

Using high-frequency water quality data to assess sampling strategies for the EU Water Framework Directive

The EU Water Framework Directive (WFD) requires that the ecological and chemical status of water bodies in Europe should be assessed, and action taken where possible to ensure that at least "good" quality is attained in each case by 2015. This paper is concerned with the accuracy and precision with which chemical status in rivers can be measured given certain sampling strategies, and how this can be improved. High-frequency (hourly) chemical data from four rivers in southern England were subsampled to simulate different sampling strategies for four parameters used for WFD classification: dissolved phosphorus, dissolved oxygen, pH and water temperature. These data sub-sets were then used to calculate the WFD classification for each site. Monthly sampling was less precise than weekly sampling, but the effect on WFD classification depended on the closeness of the range of concentrations to the class boundaries. In some cases, monthly sampling for a year could result in the same water body being assigned to three or four of the WFD classes with 95% confidence, due to random sampling effects, whereas with weekly sampling this was one or two classes for the same cases. In the most extreme case, the same water body could have been assigned to any of the five WFD quality classes. Weekly sampling considerably reduces the uncertainties compared to monthly sampling. The width of the weekly sampled confidence intervals was about 33% that of the monthly for P species and pH, about 50% for dissolved oxygen, and about 67% for water temperature. For water temperature, which is assessed as the 98th percentile in the UK, monthly sampling biases the mean downwards by about 1 °C compared to the true value, due to problems of assessing high percentiles with limited data. Low-frequency measurements will generally be unsuitable for assessing standards expressed as high percentiles. Confining sampling to the working week compared to all 7 days made little difference, but a modest improvement in precision could be obtained by sampling at the same time of day within a 3 h time window, and this is recommended. For parameters with a strong diel variation, such as dissolved oxygen, the value obtained, and thus possibly the WFD classification, can depend markedly on when in the cycle the sample was taken. Specifying this in the sampling regime would be a straightforward way to improve precision, but there needs to be agreement about how best to characterise risk in different types of river. These results suggest that in some cases it will be difficult to assign accurate WFD chemical classes or to detect likely trends using current sampling regimes, even for these largely groundwater-fed rivers. A more critical approach to sampling is needed to ensure that management actions are appropriate and supported by data.