Hormigón autocompactante con nano-adiciones de sílice y alúmina

El presente Trabajo Fin de Máster tiene por objeto principal el estudio de la influencia que tienen las adiciones tanto de Nano-Alúmina como de Nano-Sílice en el Hormigón Autocompactante (HAC). Para ello se realizará una comparativa de ensayos con un hormigón patrón cuya publicación versa en el artículo de referencia “Construction and Building Materials 55 (2014) 274–288 (On the mechanical properties and fracture behavior of polyolefin fiber-reinforced self compacting concrete)”, y con idéntica dosificación que el del presente Trabajo, pero con presencia de nano-adiciones, y comparando los ensayos de resistencia a compresión simple, módulo de elasticidad, resistencia a tracción indirecta, resistencia a flexotracción y durabilidad (índice de penetración de agua). El desarrollo del presente trabajo consta de diferentes capítulos, los cuáles se pueden englobar a grandes rasgos dentro de los siguientes tres grandes puntos: - Se elabora un pequeño estudio del estado del conocimiento, referente a hormigones autocompactantes, describiendo su elaboración convencional del mismo y en particular comentando todas los posibles aditivos y adiciones y en concreto, la descripción específica del objeto de este presente Trabajo Fin de Máster, que son las adiciones de nano-sílice y de nano-alúmina, encontrándose todo lo anterior en la literatura existente y referenciada a lo largo del presente Trabajo. El fin de lo anteriormente descrito, es el de revisar un marco teórico, que nos permitirá introducir el conocimiento de partida del presente Trabajo Fin de Máster, tomándolo a su vez como una metodología que sirva de base para el desarrollo del mismo y para futuras líneas de investigación. - Emprender una campaña experimental de laboratorio que nos permita familiarizarnos con los materiales comprendidos dentro del hormigón a tratar (HAC), pasando por cada uno de sus procedimientos de fabricación y curado, así como también conocer y desarrollar los pertinentes ensayos tanto para su estado fresco como para el estado endurecido. - Finalmente, analizar resultados obtenidos de los diferentes ensayos de laboratorio, comparando los mismos y realizando unas conclusiones y futuras líneas de investigación dentro del campo objeto del presente Trabajo Fin de Máster.

Polyolefin fiber-reinforced concrete enhanced with steel-hooked fibers in low proportions

Over the past few years, polyolefin fiber reinforced self-compacting concrete has shown high performance in both fresh and hardened state. Its fracture behavior for small deformations could be enhanced with a small amount of steel-hooked fibers, obtaining a hybrid fiber-reinforced concrete well suited for structural use. Four types of conventional fiber-reinforced concrete with steel and polyolefin fibers were produced on the basis of the same self-compacting concrete also manufactured as reference. These concrete mixtures were manufactured separately with the same fiber contents being subsequently used for two more hybrid mixtures. Fracture properties, in addition to fresh and mechanical properties, were assessed. The research showed both synergies (with the two types of fibers working together in the fracture processes) and an improvement of the orientation and distribution of the fibers on the fracture surface

Influencia de un recubrimiento de vinilo en la tensión de fractura del vidrio en ensayos de anillos concéntricos con gran superficie

El comportamiento post-rotura de los vidrios laminados es uno de los temas que están siendo investigados para explicar la capacidad de carga remanente tras la rotura de la primera lámina. En investigaciones previas se ha observado que en el caso de impacto humano en vidrios recocidos se llega a una capacidad hasta 3 veces superior, sin explicación clara del comportamiento estructural del conjunto. Para realizar un acercamiento a la resistencia a la rotura del vidrio laminado se ha planificado una campaña de ensayos de rotura con anillos concéntricos de grandes superficies en vidrio recocido, termoendurecido y templado, con dos series adicionales de vidrio recocido y termoendurecido con una capa de butiral adherida justo después del proceso de fabricación. Para realizar la comparación de las distribuciones de Weibull de las distintas tensiones de rotura se utiliza un proceso iterativo basado en la distribución real de tensiones obtenida con un modelo de elementos finitos ajustado con datos experimentales. Las comparaciones finales muestran un aumento apreciable de la resistencia (45%) en el caso de vidrios recocidos, y menor en el de los termoendurecidos (25%).The post-fracture behavior of the laminated glasses is one of the research topics that are being studied to explain the load capacity after the break of the first sheet. Previous experimental work have shown, that in case of human impact in annealed glasses, the capacity of bearing load it can be up to 3 times higher without clear explanation of the structural behavior of the plate. To make an approximation to the post-fracture resistance, a experimental program to test annealed, heat-tempered and toughened glass plates has been prepared. Two additional series of annealed and heattempered, with a layer of polyvinyl butyral adhered just after the manufacturing process, have also been incorporated. Coaxial Double Ring with large test surface areas Coaxial Double Ring with large test surface areas is the standard that has been followed. To make the comparison of Weibull's distributions of the different fracture stress, an iterative process based on the actual stress distribution obtained with a finite elements model updated with experimental results has been used. Final comparisons show a great stress improvement for the annealed glass plates (45 %), and a minor increment for the heat-tempered (25 %).

Mathematical development of stress-strain law for rock block contacts

The fracture behavior of rock block contacts has been studied for many years. Unfortunately, up to now, there is not a rigorous formulation or a solid theoretical foundation to support it. A mathematical development to represent the failure mechanism which occurs in the contacts between rock blocks is presented to evaluate the performance of breaking mechanism of such blocks relating it to the morphology of the contact and mechanical parameters of the material. The examined framework includes the evaluation of the surface roughness of first order in the failure mechanism of the granular particles of large size and the development of a theoretical model describing the morphology of the contact between rock blocks.

Madera termo-tratada de frondosas para uso estructural

La madera termotratada es madera modificada mediante un proceso térmico a elevadas temperaturas que le proporciona mayor estabilidad dimensional y durabilidad sin incorporar productos químicos perjudiciales para el medio ambiente. Hasta el momento se ha aplicado fundamentalmente a madera de coniferas por motivos económicos, siendo su uso más habitual en ambientes exteriores o de elevada humedad, como elementos de revestimiento no estructurales, carpinterías, mobiliario de jardín, etc. En la presente tesis se estudia la viabilidad de la madera termotratada de frondosas para uso estructural, en particular fresno (Fraxinus excelsior L) y haya (Fagus sylvatica L). Con este fin, y considerando que el termotratamiento modifica la estructura interna de la madera resultando en un nuevo material, se realizan estudios experimentales y numéricos para su caracterización. Estos trabajos se desarrollan bajo el enfoque de la Mecánica de Fractura debido a la pérdida de resistencia y aumento de fragilidad que presenta el material, especialmente a tracción perpendicular a las fibras. Así mismo, se lleva a cabo una recopilación de las bases, fundamentos y metodologías de esta teoría aplicados a madera sin tratar y otros materiales debido a la inexistencia de este tipo de estudios en madera termotratada. De igual manera se realiza un programa de caracterización mecánica del material para determinar sus propiedades elásticas considerando un modelo ortótropo, necesarios en la investigación del comportamiento a fractura. El trabajo derivó en el desarrollo de un nuevo método de ensayo para la determinación multiparamétrica a partir de un sólo espécimen, proporcionando resultados mucho más robustos que los obtenidos con la metodología convencional de ensayos. En base a los trabajos realizados, considerando las limitaciones de resistencia y fragilidad, así como la dudosa aplicabilidad de las normativas existentes en madera sin tratar, se aconseja no utilizar tratamientos térmicos intensos en elementos estructurales primarios. Se propone su aplicación en elementos secundarios, de manera que un posible colapso no implique una pérdida de fiabilidad global de la estructura. Se estudia la viabilidad de un panel sandwich innovador y ecológico para fachadas expuesto a cargas de viento, compuesto de madera termotratada en las caras y panel aislante de fibras de madera con función estructural en el alma. Esta investigación se desarrolló dentro del proyecto de investigación Europeo "Holiwood", Holistic implementation of European thermal treated hardwood (TMT) in the sector of construction industry and noise protection by sustainable, knowledge-based and value added products, perteneciente al sexto Programa Marco. ABSTRACT Hcat-trcatcd wood is modified wood by a thermal process at high temperatures which provides greater dimensional stability and durability without adding harmful chemicals to the environment. It has been mainly applied to softwoods due mainly to economical reasons, being its most common use outdoors or in high humidity environments, as non-structural elements, furniture, etc. The present Thesis studies the feasibility of heat-treated hardwoods for structural uses, particularly ash (Fraxinus excelsior L) and beech (Fagus sylvatica L). To this end, and considering that heat treatment modifies the internal structure of the wood resulting in a new material, experimental and numerical studies are performed for its characterization. This investigation is developed under the approach of Fracture Mechanics due to the loss of strength and the increase in brittlcncss of the material, especially in tension perpendicular to the grain. Likewise, it holds a collection of the bases, foundations and methodologies of this theory applied to untreated wood and other materials due to the lack of such studies in heat-treated wood. In addition, studies for the mechanical characterization of the material are performed in order to determine the elastic properties considering an orthotropic model. This work is necessary in the investigation of the fracture behavior. It led to the development of a new test method for multiparameter determination by using just a single specimen, providing much more robust results than those obtained with conventional test methodology. Based on this investigation, and considering the limitations of strength and brittleness, and the questionable applicability of existing standards for untreated wood, it is advised not to use intense heat treatments in primary structural elements. It is proposed the application to secondary elements, so that a possible collapse does not involve a loss of overall reliability of the structure. It is studied the feasibility of an innovative and ecological sandwich panel for facades exposed to wind loads, composed by heat-treated wood faces and insulating wood fiberboard with structural function in the core. This investigación was developed within the European research project "Holiwood", Holistic implementation of European thermal treated hardwood (TMT) in the sector of construction industry and noise protection by sustainable, knowledge-based and value added products, of the Sixth Framework Program.

Estudo experimental do comportamento à fratura frágil em aços estruturais ferríticos e aplicações à determinação da curva mestra.

Este trabalho apresenta uma investigação experimental sobre o comportamento à fratura frágil de aços estruturais ferríticos, ASTM A285 Gr C e ASTM A515 Gr 65. Os resultados deste trabalho ampliam a base de dados de propriedades mecânicas utilizadas nas análises de integridade de estruturas pressurizadas tais como vasos de pressão e tanques de armazenamento construídos com esta classe de material. O trabalho tem por objetivo também avaliar a aplicabilidade de corpos de prova de dimensões reduzidas, PCVN, na determinação da temperatura de referência, T0, por meio da metodologia da Curva Mestra, a qual define a dependência da tenacidade à fratura do material em função da temperatura. Os ensaios de tenacidade à fratura foram conduzidos utilizando-se corpos de prova solicitados em flexão três pontos com geometria SE(B), PCVN e PCVN com entalhe lateral, extraídos de chapas laminadas. Os resultados dos ensaios foram obtidos em termos de integral J no momento da instabilidade, denotados por Jc. Dados adicionais de resistência à tração e de Impacto Charpy convencional também foram obtidos para caracterizar o comportamento mecânico dos aços utilizados. Os resultados mostraram uma forte influência da geometria dos corpos de prova sobre os valores de Jc, evidenciada pela grande variação nos valores de tenacidade à fratura.

Strength-ductility behaviour of Al-Si-Cu-Mg casting alloys in T6 temper

A comparative study of the mechanical properties of 20 experimental alloys has been carried out. The effect of different contents of Si, Cu, Mg, Fe and Mn, as well as solidification rate, has been assessed using a strength-ductility chart and a quality index-strength chart developed for the alloys. The charts show that the strength generally increases and the ductility decreases with an increasing content of Cu and Mg. Increased Fe (at Fe/Mn ratio 0.5) dramatically lowers the ductility and strength of low Si alloys. Increased Si content generally increases the strength and the ductility. The increase in ductility with increased Si is particularly significant when the Fe content is high. The charts are used to show that the cracking of second phase particles imposes a limit to the maximum achievable strength by limiting the ductility of strong alloys. The (Cu + Mg) content (at.%), which determines the precipitation strengthening and the volume fraction of Cu-rich and Mg-rich intermetallics, can be used to select the alloys for given strength and ductility, provided the Fe content stays below the Si-dependent critical level for the formation of pre-eutectic alpha-phase particles or beta-phase plates.

Caracterização Microestrutural e Tribocorrosiva de Sistemas Metalocerâmicos Odontológicos do Tipo Ni-Cr/Porcelana E Ni-Cr/Ti/Porcelana

The partial fixed prosthodontics restoration is used to rehabilitate form and function of partial or total compromised teeth, having to remain permanently joined to remainder tooth. The most useful material on prosthodontics is the feldspar porcelain, commercialized as aluminosilicate powders. Dental porcelains are presented with limited mechanical properties to rehabilitate extensive spaces. The association with Ni-Cr metallic systems (metal-ceramic system) allows that the metallic substructure compensates the fragile porcelain nature, preserving the thermal insulation and aesthetics desirable, as well as reducing the possibility of cracking during matication efforts. Cohesive flaws by low mechanical strength connect the metallic substructure to the oral environment, characterized by a electrolytic solution (saliva), by aggressive temperature, pH cyclic changes and mechanical requests. This process results on ionic liberation that could promote allergic or inflammatory responses, and/or clinical degradation of ceramometal system. The aim of this study was to evaluate the presence of an intermediate titanium layer on the microscopic fracture behavior of porcelains on ceramometal systems. Plasma deposition of titanium films result in regular passivating oxide layers which act as barriers to protect the metallic substrate against the hazardous effects of corrosive saliva. Tribocorrosion tests were performed to simulate the oral environment and mechanical stress, making it possible the early detection of crack formation and growth on metal-ceramic systems, which estimate the adherence between the compounds of this system. Plain samples consisting of dental feldspar porcelain deposited either onto metallic substrates or titanium films were fired and characterized by scanning electron microscopy. The result showed that the titanium film improved the adherence of the system compared to conventional metal-ceramic interfaces, thus holding crack propagation

Phase-field analysis of finite-strain plates and shells including element subdivision

With the theme of fracture of finite-strain plates and shells based on a phase-field model of crack regularization, we introduce a new staggered algorithm for elastic and elasto-plastic materials. To account for correct fracture behavior in bending, two independent phase-fields are used, corresponding to the lower and upper faces of the shell. This is shown to provide a realistic behavior in bending-dominated problems, here illustrated in classical beam and plate problems. Finite strain behavior for both elastic and elasto-plastic constitutive laws is made compatible with the phase-field model by use of a consistent updated-Lagrangian algorithm. To guarantee sufficient resolution in the definition of the crack paths, a local remeshing algorithm based on the phase- field values at the lower and upper shell faces is introduced. In this local remeshing algorithm, two stages are used: edge-based element subdivision and node repositioning. Five representative numerical examples are shown, consisting of a bi-clamped beam, two versions of a square plate, the Keesecker pressurized cylinder problem, the Hexcan problem and the Muscat-Fenech and Atkins plate. All problems were successfully solved and the proposed solution was found to be robust and efficient.

Effect of copper addition on the fracture and fatigue crack growth behavior of solution heat-treated SUS 304H austenitic steel

Small additions of Cu to the SUS 304H, a high temperature austenitic stainless steel, enhance its high temperature strength and creep resistance. As Cu is known to cause embrittlement, the effect of Cu on room temperature mechanical properties that include fracture toughness and fatigue crack threshold of as-solutionized SUS 304H steel were investigated in this work. Experimental results show a linear reduction in yield and ultimate strengths with Cu addition of up to 5 wt.% while ductility drops markedly for 5 wt.% Cu alloy. However, the fracture toughness and the threshold stress intensity factor range for fatigue crack initiation were found to be nearly invariant with Cu addition. This is because the fracture in this alloy is controlled by the debonding from the matrix of chromium carbide precipitates, as evident from fractography. Cu, on the other hand, remains either in solution or as nano-precipitates and hence does not influence the fracture characteristics. It is concluded that small additions of Cu to 304H will not have adverse effects on its fracture and fatigue behavior. (C) 2010 Elsevier B.V. All rights reserved.

High-temperature low-cycle fatigue behavior of a NIMONIC PE-16 superalloy—Correlation with deformation and fracture

Low-cycle fatigue (LCF) responses of NIMONIC PE-16 for various prior microstructures and strain amplitudes have been evaluated and the fatigue behavior has been explained in terms of the operative deformation mechanisms. Total strain-controlled LCF tests were performed at 923 K on samples possessing three different prior microstructures: alloy A in solution-annealed condition (free of γ′ and carbides), alloy B with double aging treatment (spherical γ′ of 18-nm diameter and M23C6), and alloy C with another double aging treatment (γ′ of size 35 nm, MC and M23C6). All three microstructures exhibited an intial cyclic hardening followed by a period of gradual softening at 923 K. Coffin-Manson plots describing the plastic strain amplitudevs number of reversals to failure showed that alloy A had maximum fatigue life while C showed the least. Alloy B exhibited a two-slope behavior in the Coffin-Manson plot over the strain amplitudes investigated. This has been ascribed to the change in the degree of homogeneity of deformation at high and low strain amplitudes. Transmission electron microscopic studies were carried out to characterize the various deformation mechanisms and precipitation reactions occurring during fatigue testign. Fresh precipitation of fine γ′ was confirmed by the development of “mottled contrast” in alloy C. Evidence for the shearing of the ordered γ′ precipitates was revealed by the presence of superdislocations in alloy C. Repeated shearing during cyclic loading led to the reduction in the size of the γ′ and consequent softening. Coarser γ′ precipitates were associated with Orowan loops. The observed fatigue behavior has been rationalized based on the micromechanisms stated above and on the degree of homogenization of slip assessed by slipband spacing measurements on tested samples.

Compressive behavior and fracture features of rubber bearing glass-epoxy composites exposed to aqueous media

Epoxy systems containing HTBN rubber material and reinforced with E-glass fibres, exposed to a fixed time duration in three separate media were subjected to compressive mode of deformation. The yield stress and fractographic features noted on the compression failed samples are reported in this work. The experiment reveals that the seawater exposed sample exhibits a drop in strength compared to dry (unexposed) sample. This kind of drop is maintained if the media is changed from seawater to distilled water. When HCl is included in seawater. the experiment shows a small rise in strength value. These changes have been attributed to various factors like medium ingress into samples assisting interface failure, the larger-sized Cl- influencing the extent of diffusion of medium into system and finally their participation in the deformation phenomena. The fractographic features reveal interface separations that show either scattered debris or a cleaner surface or display a whitish-coated matrix region depending on whether the tests are done on unexposed samples or on ones following the immersion in the media.

Fracture and resistance-curve behavior in hybrid natural fiber and polypropylene fiber reinforced composites

This article presents the results of a combined experimental and theoretical study of fracture and resistance-curve behavior of hybrid natural fiber- and synthetic polymer fiber-reinforced composites that are being developed for potential applications in affordable housing. Fracture and resistance-curve behavior are studied using single-edge notched bend specimens. The sisal fibers used were examined using atomic force microscopy for fiber bundle structures. The underlying crack/microstructure interactions and fracture mechanisms are elucidated via in situ optical microscopy and ex-situ environmental scanning microscopy techniques. The observed crack bridging mechanisms are modeled using small and large scale bridging concepts. The implications of the results are then discussed for the design of eco-friendly building materials that are reinforced with natural and polypropylene fibers.

Fracture micromechanisms and mechanical behavior of YBCO bulk superconductors at 77 and 300 K

In this study two YBa2Cu3O7−δ bulk superconductors were evaluated, with the aim of analyzing the influence of the processing method (TSMG and Bridgman) and the test temperature on their mechanical behavior. The relationship between their mechanical properties and fracture micromechanisms has also been studied. Both materials were tested at room and at service temperature. TPB tests were carried out to determine their mechanical behavior, strength and toughness. Moreover, one of the two materials, characterized by transversal microstructural anisotropy, was tested in two directions. Hardness of both materials at nano and micro scale was studied. The results show that the mechanical behavior of the materials is controlled by the defects and cracks that have been introduced during the processing of the materials. A good degree of agreement was found between the experimental crack defects detected by means of SEM and those gathered from the fracture mechanical analysis of the experimental data

Molecular dynamics simulation of mechanical behavior of osteopontin-hydroxyapatite interfaces

Bone is characterized with an optimized combination of high stiffness and toughness. The understanding of bone nanomechanics is critical to the development of new artificial biological materials with unique properties. In this work, the mechanical characteristics of the interfaces between osteopontin (OPN, a noncollagenous protein in extrafibrillar protein matrix) and hydroxyapatite (HA, a mineral nanoplatelet in mineralized collagen fibrils) were investigated using molecular dynamics method. We found that the interfacial mechanical behaviour is governed by the electrostatic attraction between acidic amino acid residues in OPN and calcium in HA. Higher energy dissipation is associated with the OPN peptides with a higher number of acidic amino acid residues. When loading in the interface direction, new bonds between some acidic residues and HA surface are formed, resulting in a stick-slip type motion of OPN peptide on the HA surface and high interfacial energy dissipation. The formation of new bonds during loading is considered to be a key mechanism responsible for high fracture resistance observed in bone and other biological materials.