Foam-forming properties of Ilex paraguariensis (mate) saponin: foamability and foam lifetime analysis by Weibull equation

Saponins are natural soaplike foam-forming compounds widely used in foods, cosmetic and pharmaceutical preparations. In this work foamability and foam lifetime of foams obtained from Ilex paraguariensis unripe fruits were analyzed. Polysorbate 80 and sodium dodecyl sulfate were used as reference surfactants. Aiming a better data understanding a linearized 4-parameters Weibull function was proposed. The mate hydroethanolic extract (ME) and a mate saponin enriched fraction (MSF) afforded foamability and foam lifetime comparable to the synthetic surfactants. The linearization of the Weibull equation allowed the statistical comparison of foam decay curves, improving former mathematical approaches.

Numerical Investigation of Flow Past a Circular Cylinder and in a Staggered Tube Bundle Using Various Turbulence Models

Transitional flow past a three-dimensional circular cylinder is a widely studied phenomenon since this problem is of interest with respect to many technical applications. In the present work, the numerical simulation of flow past a circular cylinder, performed by using a commercial CFD code (ANSYS Fluent 12.1) with large eddy simulation (LES) and RANS (κ - ε and Shear-Stress Transport (SST) κ - ω! model) approaches. The turbulent flow for ReD = 1000 & 3900 is simulated to investigate the force coefficient, Strouhal number, flow separation angle, pressure distribution on cylinder and the complex three dimensional vortex shedding of the cylinder wake region. The numerical results extracted from these simulations have good agreement with the experimental data (Zdravkovich, 1997). Moreover, grid refinement and time-step influence have been examined. Numerical calculations of turbulent cross-flow in a staggered tube bundle continues to attract interest due to its importance in the engineering application as well as the fact that this complex flow represents a challenging problem for CFD. In the present work a time dependent simulation using κ – ε, κ - ω! and SST models are performed in two dimensional for a subcritical flow through a staggered tube bundle. The predicted turbulence statistics (mean and r.m.s velocities) have good agreement with the experimental data (S. Balabani, 1996). Turbulent quantities such as turbulent kinetic energy and dissipation rate are predicted using RANS models and compared with each other. The sensitivity of grid and time-step size have been analyzed. Model constants sensitivity study have been carried out by adopting κ – ε model. It has been observed that model constants are very sensitive to turbulence statistics and turbulent quantities.

Static pressure and wall shear stress distributions in air flow in a seven wire-wrapped rod bundle

An experimental investigation is performed in a turbulent flow in a seven wire-wrapped rod bundle, mounted in an open air facility. Static pressure distributions are measured on central and peripheral rods. By using a Preston tube, the wall shear stress profiles are experimentally obtained along the perimeter of the rods. The geometric parameters of the test section are P/D=1.20 and H/D=15. The measuring section is located at L/D=40 from the air inlet. It is observed that the dimensionless static pressure and wall shear stress profiles are nearly independent of the Reynolds number and strongly dependent of the wire-spacer position, with abrupt variations of the parameters in the neighborhood of the wires.

Two-phase flow measurements with spacer grid in a rod bundle geometry

Heat transfer effectiveness in nuclear rod bundles is of great importance to nuclear reactor safety and economics. An important design parameter is the Critical Heat Flux (CHF), which limits the transferred heat from the fuel to the coolant. The CHF is determined by flow behaviour, especially the turbulence created inside the fuel rod bundle. Adiabatic experiments can be used to characterize the flow behaviour separately from the heat transfer phenomena in diabatic flow. To enhance the turbulence, mixing vanes are attached to spacer grids, which hold the rods in place. The vanes either make the flow swirl around a single sub-channel or induce cross-mixing between adjacent sub-channels. In adiabatic two-phase conditions an important phenomenon that can be investigated is the effect of the spacer on canceling the lift force, which collects the small bubbles to the rod surfaces leading to decreased CHF in diabatic conditions and thus limits the reactor power. Computational Fluid Dynamics (CFD) can be used to simulate the flow numerically and to test how different spacer configurations affect the flow. Experimental data is needed to validate and verify the used CFD models. Especially the modeling of turbulence is challenging even for single-phase flow inside the complex sub-channel geometry. In two-phase flow other factors such as bubble dynamics further complicate the modeling. To investigate the spacer grid effect on two-phase flow, and to provide further experimental data for CFD validation, a series of experiments was run on an adiabatic sub-channel flow loop using a duct-type spacer grid with different configurations. Utilizing the wire-mesh sensor technology, the facility gives high resolution experimental data in both time and space. The experimental results indicate that the duct-type spacer grid is less effective in canceling the lift force effect than the egg-crate type spacer tested earlier.

Effect of calcium intake on urinary oxalate excretion in calcium stone-forming patients

Dietary calcium lowers the risk of nephrolithiasis due to a decreased absorption of dietary oxalate that is bound by intestinal calcium. The aim of the present study was to evaluate oxaluria in normocalciuric and hypercalciuric lithiasic patients under different calcium intake. Fifty patients (26 females and 24 males, 41 ± 10 years old), whose 4-day dietary records revealed a regular low calcium intake (<=500 mg/day), received an oral calcium load (1 g/day) for 7 days. A 24-h urine was obtained before and after load and according to the calciuria under both diets, patients were considered as normocalciuric (NC, N = 15), diet-dependent hypercalciuric (DDHC, N = 9) or diet-independent hypercalciuric (DIHC, N = 26). On regular diet, mean oxaluria was 30 ± 14 mg/24 h for all patients. The 7-day calcium load induced a significant decrease in mean oxaluria compared to the regular diet in NC and DIHC (20 ± 12 vs 26 ± 7 and 27 ± 18 vs 32 ± 15 mg/24 h, respectively, P<0.05) but not in DDHC patients (22 ± 10 vs 23 ± 5 mg/24 h). The lack of an oxalate decrease among DDHC patients after the calcium load might have been due to higher calcium absorption under higher calcium supply, with a consequent lower amount of calcium left in the intestine to bind with oxalate. These data suggest that a long-lasting regular calcium consumption <500 mg was not associated with high oxaluria and that a subpopulation of hypercalciuric patients who presented a higher intestinal calcium absorption (DDHC) tended to hyperabsorb oxalate as well, so that oxaluria did not change under different calcium intake.

Possibility of press forming wood films into primary packaging

In recent times the packaging industry is finding means to maximize profit. Wood used to be the most advantageous and everyday material for packaging, worktables, counters, constructions, interiors, tools and as materials and utensils in the food companies in the world. The use of wood has declined vigorously, and other materials like plastic, ceramic, stainless steel, concrete, and aluminum have taken its place. One way that the industry could reduce its cost is by finding possibilities of using wood for primary packaging after which it can be safely recycled or burned as a carbon source for energy. Therefore, the main objective of this thesis is to investigate the possibility of press-forming a wood film into primary packaging. In order to achieve the stated objectives, discussion on major characteristics of wood in terms of structure, types and application were studied. Two different wood species, pine and birch were used for the experimental work. These were provided by a local carpentry workshop in Lappeenranta and a workshop in Ruokolahti supervised by Professor Timo Kärki. Laboratory tests were carried out at Lappeenranta University of Technology FMS workshop on Stenhøj EPS40 M hydraulic C-frame press coupled with National Instruments VI Logger and on the Adjustable packaging line machine at LUT Packaging laboratory. The tests succeeded better on the LUT packaging line than on the Stenhoj equipment due to the integrated heating system in the machine. However, there is much work to be done before the quality of a tray produced from the wood film is comparable to that of the wood plastic composite tray.

Forming i barnehagen i lys av Reggio Emilias atelierkultur

Forming (Arts and crafts) and children’s creative action with materials and tools are less in use in the kindergarten than before. Political focus on children’s early learning has led to shifts in kindergartens toward other specific disciplines, and requirements for individual testing also of the smallest children’s competencies within these. Kindergarten teachers, educators, researchers and participants in social debate have pointed out that there are epistemological contradictions in descriptions of kindergarten quality as well as between current kindergarten policy documents and requirements for the kindergartens’ staff. Meanwhile, the content and methods in many kindergartens are inspired by practice and philosophy in the municipal kindergartens in Reggio Emilia, Italy. Correlation between kindergartens’ formingprojects and experiences from Reggio Emilia is actualized in particular through the workshop and the studio’s role in children’s learning processes. One starting point for the thesis’ problem area is a documented need for more knowledge about kindergarten’s educational content. The overarching goal of the thesis is to develop new knowledge about how learning takes place in kindergarten through examining the field of forming in kindergartens inspired by Reggio Emilia’s atelier culture. The thesis is theoretically anchored within pragmatism, and ties kindergarten’s aesthetic operations with materials and tools to socio-cultural perspective, social constructivism and post humanistic theory. The empirical material is obtained through a qualitative study with ethnography as methodological approach. The fieldwork is conducted in kindergarten, with two leading research questions: 1) How is atelierism perceived and unfolded in Norwegian Reggio Emilia-inspired kindergartens, and 2) how is forming perceived and unfolded in Norwegian Reggio Emilia-inspired kindergartens. A comprehensive and multifaceted material is analyzed, and the results are presented in the form of three themes: The physical environment, Relations and actions in interplay, and Expression forms and forms of expression. Each of these topics are supported by examples from kindergartens’ adult voices and the constructed empirical material. Insights into how learning takes place in the kindergarten subject of forming with inspiration from the Reggio Emilia atelier culture is discussed in the tension between educational philosophy, Nordic kindergarten tradition and neoliberal trends that kindergarten teachers must adhere to. Learning potentials in children’s opportunities for action in forming in light of the atelier appears in the results of the empirical study. The educational context described is characterized by experimental and playful actions where children’s sensations, curiosity and resistance are interacting with the identity of materials and tools. The results imply aesthetic, ethical, democratic and ecological reflections, which are also valid on a practical action level. The thesis contributes to description and understanding of kindergarten’ content and young children’s learning, the importance of atelier culture as inspiration for the kindergarten, and the further development of methodology and documentation of knowledge expressions.

Neutralization of the edema-forming, defibrinating and coagulant effects of Bothrops asper venom by extracts of plants used by healers in Colombia

We determined the neutralizing activity of 12 ethanolic extracts of plants against the edema-forming, defibrinating and coagulant effects of Bothrops asper venom in Swiss Webster mice. The material used consisted of the leaves and branches of Bixa orellana (Bixaceae), Ficus nymphaeifolia (Moraceae), Struthanthus orbicularis (Loranthaceae) and Gonzalagunia panamensis (Rubiaceae); the stem barks of Brownea rosademonte (Caesalpiniaceae) and Tabebuia rosea (Bignoniaceae); the whole plant of Pleopeltis percussa (Polypodiaceae) and Trichomanes elegans (Hymenophyllaceae); rhizomes of Renealmia alpinia (Zingiberaceae), Heliconia curtispatha (Heliconiaceae) and Dracontium croatii (Araceae), and the ripe fruit of Citrus limon (Rutaceae). After preincubation of varying amounts of each extract with either 1.0 µg venom for the edema-forming effect or 2.0 µg venom for the defibrinating effect, the mixture was injected subcutaneously (sc) into the right foot pad or intravenously into the tail, respectively, to groups of four mice (18-20 g). All extracts (6.2-200 µg/mouse) partially neutralized the edema-forming activity of venom in a dose-dependent manner (58-76% inhibition), with B. orellana, S. orbicularis, G. panamensis, B. rosademonte, and D. croatii showing the highest effect. Ten extracts (3.9-2000 µg/mouse) also showed 100% neutralizing ability against the defibrinating effect of venom, and nine prolonged the coagulation time induced by the venom. When the extracts were administered either before or after venom injection, the neutralization of the edema-forming effect was lower than 40% for all extracts, and none of them neutralized the defibrinating effect of venom. When they were administered in situ (sc at the same site 5 min after venom injection), the neutralization of edema increased for six extracts, reaching levels up to 64% for C. limon.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.

Press forming of paperboard – advancement of converting tools and process control

Press forming is nowadays one of the most common industrial methods in use for producing deeper trays from paperboard. Demands for material properties like recyclability and sustainability have increased also in the packaging industry, but there are still limitations related to the formability of paperboard. A majority of recent studies have focused on material development, but the potential of the package manufacturing process can also be improved by the development of tooling and process control. In this study, advanced converting tools (die cutting tools and the press forming mould) are created for production scale paperboard tray manufacturing. Also monitoring methods that enable the production of paperboard trays with enhanced quality, and can be utilized in process control are developed. The principles for tray blank preparation, including creasing pattern and die cutting tool design are introduced. The mould heating arrangement and determination of mould clearance are investigated to improve the quality of the press formed trays. The effect of the spring back of the tray walls on the tray dimensions can be managed by adjusting the heat-related process parameters and estimating it at the mould design stage. This enables production speed optimization as the process parameters can be adjusted more freely. Real-time monitoring of pressing force by using multiple force sensors embedded in the mould structure can be utilized in the evaluation of material characteristics on a modified production machinery. Comprehensive process control can be achieved with a combination of measurement of the outer dimensions of the trays and pressing force monitoring. The control method enables detection of defects and tracking changes in the material properties. The optimized converting tools provide a basis for effective operation of the control system.

Factors Affecting Runnability of Press Forming Equipment

The growth of the food packaging industry has raised more interest in bio-based fibre packing. The use of petroleum based packages is unfriendly to the environment while bio-based is a sustainable option for food packing. In this Master Thesis the aim was to discover how the press forming machineries runnability is affected by parameters of the press and how it also affects formability of paperboard trays. Familiarisation of the working operation parameters was done with the KAMA ST 75 flat-bed die cutting machine and the VP3-70 mould press. Some small test runs of moulding trays where done to get acquainted to the adjustment parameters of the machines. Literature study was done on how paperboards physical properties react to the forces applied during press forming. The study of what kind of defects to the paperboard tray might occur during forming process and the causes for these defects. Also how the parameters of the press forming machine affects formability of the tray. Maintenance procedures was done to the press forming machine to enhance the reliably of production process. Tool alignment measurement was done to determine proper alignment. Laboratory test of the physical properties of the test material was done to find any connection to how the test material performs in press forming. An evaluation criterion was made to evaluate the dimensions and defects of the tray. From the test result a conclusion can be drawn on how the parameters of the press forming process affect the paperboard material. Based on the results the adjustment the parameters of moulding machines to the mechanical properties of paperboard it is possible to produce high quality fibre passed trays for the food packaging industry.

Investigations into the determinations of hydride-forming elements

Analytical methods for the determination of trace amounts of germanium, tin and arsenic were established using hydride generation coupled with direct current plasma atomic emission spectrometry. A continuous gas flowing batch system for the hydride generation was investigated and was applied to the determination of germanium(Ge), tin(Sn), antimony(Sb) and lead(Pb) (Preliminary results suggest that it is also applicable to arsenic)As) ). With this system, the reproducibility of signals was improved and the determination was speeded up, compared with the conventional batch type hydride generation system. Each determination was complete within one minute. Interferences from a number of transition metal ions, especially from Pd(II), Pt(IV), Ni(II), Cu(II), Co(II), and Fe(II, III), have proven to be very serious under normal conditions, in the determination of germanium, tin, and arsenic. These interference effects were eliminated or significantly reduced in the presence of L-cystine or L-cysteine. Thus, a 10-1000 fold excess of Ni(II), Cu(II), Co(II), Fe(II), Pt(IV), Pd(II), etc. can be tolerated without interference, In the presence of L-cystine or L-cysteine, compared with absence of interference reducing agent. The methods for the determination of Ge, Sn, and As were examined by the analyses of standard reference materials. Interference effects from the sample matrix, for example, in transition metal-rich samples, copper, iron and steel, were eliminated by L-cystine (for As and Sn) and by LI cysteine (for Ge). The analysis of a number of standard reference materials gave excellent results of As and Sn contents in agreement with the certified values, showing there was no systematic interference. The detection limits for both germanium and tin were 20 pg ml- I . Preliminary studies were carried out for the determination of antimony and lead. Antimony was found to react with NaBH4, remaInIng from the previous determinations, giving an analytical signal. A reversed injection manner, i.e., injection of the NaBH4 solution prior to the analyte solution was used to avoid uncertainty caused by residual NaBH4 present and to ensure that an excess of NaB H4 was available. A solution of 0.4% L-cysteine was found to reduce the interference from selected transition metal ions, Co(II), Cu(II), Ni(II) and Pt(IV). Hydrochloric acid - hydrogen peroxide, nitric acid - ammonium persulphate, and potassium dichromate malic acid reaction systems for lead hydride generation were compared. The potassium dichromate - malic acid reaction medium proved to be the best with respect to reproducibility and minimal interference. Cu(II), Ni(II), and Fe(II) caused strong interference In lead determinations, which was not reduced by L-cysteine or Lcystine. Sodium citrate, ascorbic acid, dithizone, thiosemicarbazide and penicillamine reduced interferences to some extent. Further interference reduction studies were carried out uSIng a number of amino acids, glycine, alanine, valine, leucine and histidine, as possible interference reducing agents in the determination of germanium. From glycine, alanine, valine to leucine, the interference reduction effect in germanium determinations decreased. Histidine II was found to be very promising In the reduction of interference. In fact, histidine proved more efficient than L-cystine and L-cysteine In the reduction of interference from Ni(II) in the determination of germanium. Signal enhancement by easily ionized elements (EIEs), usually regarded as an interference effect in analysis by DCP-AES, was studied and successfully applied to advantage in improving the sensitivity and detection limit in the determination of As, Ge, Sn, Sb, and Pb. The effect of alkali and alkaline-earth elements on the determination of the above five hydride forming elements was studied. With the appropriate EIE, a signal enhancement of 40-115% was achieved. Linear calibration and good reproducibility were also obtained in the presence of EIEs. III

The versatility and utilization of phosphorus based compounds in classic carbon-carbon bond forming and esterification reactions

The phosphonium salt room temperature ionic liquid tetradecyltrihexylphosphonium chloride (THPC) has been employed as an efficient reusable media for the palladium catalyzed Suzuki cross-coupling reaction of aryl halides, including aryl chlorides, under mild conditions. The cross-coupling reactions were found to proceed in THPC containing small amounts ofwater and toluene (single phase) using potassium phosphate and 1% Pd2(dba)3'CHCI3. Variously substituted iodobenzenes, including electron rich derivatives, reacted efficiently in THPC with a variety of arylboronic acids and were all complete within 1 hour at 50°C. The corresponding aryl bromides also reacted under these conditions with the addition of a catalytic amount of triphenylphosphine that allowed for complete conversion and high isolated yields. The reactions involving aryl chlorides were considerably slower, although the addition of triphenylphosphine and heating at 70°C allowed high conversion of electron deficient derivatives. Addition of water and hexane to the reaction products results in a triphasic system, from which the catalyst was then recycled by removing the top (hexanes) and bottom (aqueous) layers and adding the reagents to the ionic liquid which was heated again at 50°C; resulting in complete turnover of iodobenzene. Repetition of this procedure gave the biphenyl product in 82-97% yield (repeated five times) for both the initial and recycled reaction sequences. IL ESTERIFICATIONREACTION A new class oftrialkylphosphorane has been prepared through reaction of a trialkylphosphine with 2-chlorodimethylmalonate in the presence oftriethylamine. These new reagents promote the condensation reaction of carboxylic acids with alcohols to provide esters along with trialkylphosphine oxide and dimethylmalonate. The condensation reaction of chiral secondary alcohols can be controlled to give either high levels of inversion or retention through a subtle interplay involving basicity of the reaction media, solvent, and tuning the electronic and steric nature of the carboxylic acid and stenc nature of the phosphorane employed. A coherent mechanism is postulated to explain these observations involving reaction via an initial acyloxyphosphonium ion.

Rôle des facteurs physico-chimiques du micro-environnement intestinal et des boucles inter-hélicales du Domaine I dans l’activité de la toxine insecticide Cry9Ca du bacille de Thuringe

Une fois ingérées par un insecte sensible, les toxines insecticides du bacille de Thuringe doivent être activées par les protéases intestinales de cet insecte. Leur premier domaine, un ensemble de sept hélices-α amphipathiques, est responsable de leur insertion dans la membrane luminale de certaines cellules de l’intestin médian, ce qui crée des pores peu sélectifs. La toxicité et la capacité à former des pores d’une telle toxine, la Cry9Ca, de ses mutants simples R164A et R164K et d’un fragment de 55 kDa résultant d’un clivage protéolytique au niveau de son résidu 164 ont été étudiées à l’aide d’une combinaison de modélisation par homologie, de bioessais, d’expériences de gonflement osmotique avec des vésicules de membrane en bordure en brosse de larves de sphinx du tabac et de mesures électrophysiologiques sur des intestins isolés. Ni les mutations simples ni le clivage protéolytique n’ont altéré la toxicité de la Cry9Ca. Dans une solution à faible force ionique, toutefois, la formation des pores dépend fortement du pH : une augmentation de celui-ci de 6,5 à 10,5 a entraîné une baisse irrégulière et par étapes successives de la perméabilité membranaire. Les quatre préparations de toxine ont néanmoins dépolarisé la membrane apicale d’intestins médians fraîchement isolés baignant dans une solution contenant 122 mM de KCl à pH 10,5. L’activité de la Cry9Ca, et des mutants R164A et R164K, a été grandement stimulée lorsque les expériences ont été effectuées en présence de suc intestinal, de lipides extraits d’un volume équivalent de suc intestinal ou d’un cocktail d’inhibiteurs de protéases solubles dans l’eau. De plus, le rôle des boucles inter-hélicales du Domaine I lors de l’insertion dans la membrane a été étudié avec des mutants doubles de la Cry9Ca dont les mutations introduisaient, neutralisaient ou renversaient une charge électrique. À l’exception de trois d’entres eux, tous ces mutants ont conservé une toxicité et une capacité à former des pores comparables à celles de la toxine parentale. L’ensemble de ces résultats suggère que le micro-environnement de l’intestin médian contribue à minimiser l’influence des charges de surface portées par les résidus des boucles inter-hélicales du Domaine I sur la capacité des toxines du bacille de Thuringe à former des pores. Il indique aussi que, d’une part, selon le site de clivage et les conditions expérimentales utilisées, des protéolyses supplémentaires de la toxine Cry9Ca activée peuvent soit stimuler, soit nuire à son activité et que, d’autre part, le suc intestinal du sphinx du tabac contient probablement un inhibiteur de protéases qui pourrait jouer un rôle important dans l’activité des toxines du bacille de Thuringe.