Estudo experimental sobre o comportamento do escoamento bifásico água - ar para a medição de vazão em placa de orifício

The measurement of flow through the prediction of differential pressure is widely used in industrial day-to-day, this happens mainly due to the fact that it is used for various types of fluids, such as gas flow and liquid with viscosity distinct even flow of fluids with particles in suspension. The suitability of this equipment for measuring mass flow in two-phase flow is of paramount importance for technological development and reliability of results. When it comes to two-phase flow the relationship between the fluids and their interactions are of paramount importance in predicting the flow. In this paper, we propose the use of concentric orifice plate used in small diameter pipes of 25.4 mm order where a two-phase flow flows between water-air. The measurement of single-phase flow was made with the use of data in NBR 5167-1 which was used to Stolz equation for measuring discharge coefficient. In the two-phase flow was used two correlations widely used in the prognosis of mass flow, the pattern of Zhang (1992) and the model of Chisholm (1967), to the homogeneous flow model. It was observed that the behavior found in Zhang model are consistent more realistic way the mass flow of two-phase flow, since the model Chisholm extrapolate the parameters for the downstream pressure P2, the orifice plate, and the rated discharge coefficient. The use of the change in pressure drop P1-P2 and discharge coefficient, led to a better convergence of the values obtained for the two-phase air-water stream.

Positronium collisions with rare-gas atoms

We calculate elastic scattering of positronium (Ps) by the Xe atom using the recently developed pseudopotential method (Fabrikant and Gribakin 2014 Phys. Rev. A 90 052717) and review general features of Ps scattering from heavier rare-gas atoms: Ar, Kr and Xe. The total scattering cross section is dominated by two contributions: elastic scattering and Ps ionization (break-up). To calculate the Ps ionization cross sections we use the binary-encounter method for Ps collisions with an atomic target. Our results for the ionization cross section agree well with previous calculations carried out in the impulse approximation. Our total Ps–Xe cross section, when plotted as a function of the projectile velocity, exhibits similarity with the electron-Xe cross section for the collision velocities higher than 0.8 a.u., and agrees very well with the measurements at Ps velocities above 0.5 a.u.

Efficient and Selectable Production of Reactive Species Using a Nanosecond Pulsed Discharge in Gas Bubbles in Liquid

A plasma gas bubble-in-liquid method for high production of selectable reactive species using a nanosecond pulse generator has been developed. The gas of choice is fed through a hollow needle in a point-to-plate bubble discharge, enabling improved selection of reactive species. The increased interface reactions, between the gas-plasma and water through bubbles, give higher productivity. H₂O₂ was the predominant species produced using Ar plasma, while predominantly  and NO₂ were generated using air plasma, in good agreement with the observed emission spectra. This method has nearly 100% selectivity for H₂O₂, with seven times higher production, and 92% selectivity for , with nearly twice the production, compared with a plasma above the water.

Use of inert gas-enriched atmospheres and post-packaging irradiation in shelf-life extension of watercress

Watercress (Nasturtium officinale R. Br.) is a semi-aquatic plant of the Brassicaceae family highly appreciated in the Mediterranean cuisine. It features sharp, peppery and slightly tangy taste and contains health-promoting phytochemicals. Its consumption as a fresh-cut product has increased in recent years, as well as the global market of minimally processed vegetables. This demand is driven by the growing interest in the role of food in promoting the human health and wellbeing and to meet consumer needs for fresh-like and more convenient foods. Due to the reduced shelf-life of this plant, the suitability of inert gas-enriched atmospheres and ionizing irradiation for preserving visual, nutritional and functional quality attributes during cold storage was studied. Watercress samples were gathered in the Northeast region of Portugal, rinsed in tap water and a portion was immediately analyzed (non-stored control). The remaining fresh material was packaged in polyethylene bags under N2- and Ar-enriched atmospheres, conventional atmosphere (air) and vacuum (no atmosphere). Samples under conventional atmosphere were irradiated at 1, 2 and 5 kGy of gamma-rays (predicted doses) in a 60Co experimental chamber. A non-irradiated control followed all the experiment. Then, all packaged samples were stored at 4 ºC for 7 days. The studied quality parameters included the colour that was measured with a Konica Minolta colorimeter, and total soluble solids and pH determined in squeezed juice. The proximate composition (moisture, proteins, fat, ash, carbohydrates and energy) was evaluated using the AOA C procedures. Organic acids, free sugars, fatty acids and tocopherols were analyzed by chromatographic techniques. Samples were also evaluated for its DPPH• scavenging activity, reducing power, and lipid peroxidation inhibition capacity trough the inhibition of the β-carotene bleaching and thiobarbituric acid reactive substances (TBAR S) formation. Differences among treatments were analyzed using the one-way analysis of variance (ANO VA) and a linear discriminant analysis (LDA ) was used to evaluate the effects on the overall postharvest quality. After evaluating the effect on the individual quality parameters, the LDA revealed that the Ar-enriched atmosphere and the irradiation at 2 kGy were suitable processing choices for preserving the integrity of the non-stored control samples during cold storage. Thus, these non-thermal treatments were highlighted for shelf-life extension of fresh-cut watercress.

Postharvest quality changes in fresh-cut watercress stored under conventional and inert gas-enriched modified atmosphere packaging

The effect of modified atmosphere packaging (MAP) on the postharvest quality of fresh-cut watercress (Nasturtium officinale R. Br.) stored at 4 ºC for 7 d was studied. A portion of watercress was immediately analyzed (non-stored control) and the remaining fresh material was stored packaged under atmospheres enriched with N2, Ar, air, or vacuum. The analyzed parameters included colour, total soluble solids, pH, macronutrients, the individual profiles of sugars, organic acids, tocopherols and fatty acids, and total phenolics and flavonoids. Furthermore, four in vitro assays were performed to evaluate the antioxidant activity. After assessing the effect on individual quality parameters, it was possible to conclude that air was the less efficient atmosphere in preserving quality attributes of the non-stored control samples during cold storage. In turn, Ar-enriched MAP was the most suitable choice to preserve the overall postharvest quality. The present study also highlighted the nutritional and antioxidant properties of watercress, as well as the interest of its inclusion in human diets.

Particle and gaseous emissions from compressed natural gas and ultralow sulphur diesel-fuelled buses at four steady engine loads

Exhaust emissions from thirteen compressed natural gas (CNG) and nine ultralow sulphur diesel in-service transport buses were monitored on a chassis dynamometer. Measurements were carried out at idle and at three steady engine loads of 25%, 50% and 100% of maximum power at a fixed speed of 60 kmph. Emission factors were estimated for particle mass and number, carbon dioxide and oxides of nitrogen for two types of CNG buses (Scania and MAN, compatible with Euro 2 and 3 emission standards, respectively) and two types of diesel buses (Volvo Pre-Euro/Euro1 and Mercedez OC500 Euro3). All emission factors increased with load. The median particle mass emission factor for the CNG buses was less than 1% of that from the diesel buses at all loads. However, the particle number emission factors did not show a statistically significant difference between buses operating on the two types of fuel. In this paper, for the very first time, particle number emission factors are presented at four steady state engine loads for CNG buses. Median values ranged from the order of 1012 particles min-1 at idle to 1015 particles km-1 at full power. Most of the particles observed in the CNG emissions were in the nanoparticle size range and likely to be composed of volatile organic compounds The CO2 emission factors were about 20% to 30% greater for the diesel buses over the CNG buses, while the oxides of nitrogen emission factors did not show any difference due to the large variation between buses.

Microstructural characterization of electron beam evaporated tungsten oxide films for gas sensing applications

Tungsten trioxide is one of the potential semiconducting materials used for sensing NH3, CO, CH4 and acetaldehyde gases. The current research aims at development, microstructural characterization and gas sensing properties of thin films of Tungsten trioxide (WO3). In this paper, we intend to present the microstructural characterization of these films as a function of post annealing heat treatment. Microstructural and elemental analysis of electron beam evaporated WO3 thin films and iron doped WO3 films (WO3:Fe) have been carried out using analytical techniques such as Transmission electron microscopy, Rutherford Backscattered Spectroscopy and XPS analysis. TEM analysis revealed that annealing at 300oC for 1 hour improves cyrstallinity of WO3 film. Both WO3 and WO3:Fe films had uniform thickness and the values corresponded to those measured during deposition. RBS results show a fairly high concentration of oxygen at the film surface as well as in the bulk for both films, which might be due to adsorption of oxygen from atmosphere or lattice oxygen vacancy inherent in WO3 structure. XPS results indicate that tungsten exists in 4d electronic state on the surface but at a depth of 10 nm, both 4d and 4f electronic states were observed. Atomic force microscopy reveals nanosize particles and porous structure of the film. This study shows e-beam evaporation technique produces nanoaparticles and porous WO3 films suitable for gas sensing applications and doping with iron decreases the porosity and particle size which can help improve the gas selectivity.

Electron beam evaporation of tungsten oxide films for gas sensors

Pure and Iron incorporated nanostructured Tungsten Oxide (WO3) thin films were investigated for gas sensing applications using noise spectroscopy. The WO3 sensor was able to detect lower concentrations (1 ppm-10 ppm) of NH3, CO, CH4 and Acetaldehyde gases at higher operating temperatures between 100oC to 250oC. The response of the WO3 sensor to NH3, CH4 and Acetaldehyde at lower temperatures (50oC-100oC) was significant when the sensor was photo-activated using blue-light emitting diode (Blue-LED). The WO3 with Fe (WO3:Fe) was found to show some response to Acetaldehyde gas only at relatively higher operating temperature (250oC) and gas concentration of 10 ppm.

Thin film deposition and characterization of pure and iron-doped electron-beam evaporated tungsten oxide for gas sensors

Pure Tungsten Oxide (WO3) and Iron-doped (10 at%) Tungsten Oxide (WO3:Fe) nanostructured thin films were prepared using a dual crucible Electron Beam Evaporation techniques. The films were deposited at room temperature in high vacuum condition on glass substrate and post-heat treated at 300 oC for 1 hour. From the study of X-ray diffraction and Raman the characteristics of the as-deposited WO3 and WO3:Fe films indicated non-crystalline nature. The surface roughness of all the films showed in the order of 2.5 nm as observed using Atomic Force Microscopy (AFM). X-Ray Photoelectron Spectroscopy (XPS) analysis revealed tungsten oxide films with stoichiometry close to WO3. The addition of Fe to WO3 produced a smaller particle size and lower porosity as observed using Transmission Electron Microscopy (TEM). A slight difference in optical band gap energies of 3.22 eV and 3.12 eV were found between the as-deposited WO3 and WO3:Fe films, respectively. However, the difference in the band gap energies of the annealed films were significantly higher having values of 3.12 eV and 2.61 eV for the WO3 and WO3:Fe films, respectively. The heat treated samples were investigated for gas sensing applications using noise spectroscopy and doping of Fe to WO3 reduced the sensitivity to certain gasses. Detailed study of the WO3 and WO3:Fe films gas sensing properties is the subject of another paper.