Dynamic functional impression technique fo severely resorbed alveolar ridges

The process of bone resorption can reduce the volume of the alveolar crest, which makes may make difficult impression taking of the alveolar tissue and the subsequent fit of a new denture. This clinical report describes a fast and simple technique for impressions of edentulous ridges to replace complete dentures, using a temporary tissue conditioner material on the denture base. The existing denture must cover the whole supporting area and should be in harmony with the adjacent oral structures. This technique reduces the number of steps involved and minimizes treatment time and expenses.

Avaliação da perda óssea alveolar em pacientes encaminhados à especialista em periodontia: estudo radiográfico

The aim of this study was to evaluate the mean of alveolar bone loss (%) in radiographies of patients referred to specialist for periodontal treatment. Full mouth series of periapical radiographies (paralelism technique) were used. A total of 9808 proximal surfaces in 4804 teeth of 213 patients (90 males and 123 females), mean age, 44.3 years, were assessed. The alveolar bone loss was measured in relation to root lenght expressed as an average similar to Schei 's technique (1959) without the use of ruler. The references used were the distances cement-enamel juntion (CEJ) - alveolar crest (AC) and CEJ- dental apex taken with a digimatic caliper. The results showed that the mean values of alveolar bone loss (%ABL) was 22.39%. Men showed higher mean values of %ABL than women; the %ABL increased with the age, but the difference among age groups was no statistical significant (p>0.05); the mean values of %ABL of distal surfaces was higher than mesial surfaces (p<0.01), ríght quadrants exhibited higher %ABL values than left quadrants (p<0.01); maxillary sites showed mean values of %ABL higher than mandibular sites; the highest mean values of %ABL was found in molar group, followed by incisor groups, and premolar group; the canine group exhibited lower mean values of %ABL; the differences among the groups was considered statitistically significant (p<0.01). lt was suggested the usage of this technique in the dentistry offices and radiological services for the patient 's documentation and assortment and for later comparison about alveolar bone level

Observable stages and scheduling for alveolar remodeling following antemortem tooth loss

Zahnverlust zu Lebzeiten („antemortem tooth loss“, AMTL) kann als Folge von Zahnerkrankungen, Traumata, Zahnextraktionen oder extremer kontinuierlicher Eruption sowie als Begleiterscheinung fortgeschrittener Stadien von Skorbut oder Lepra auftreten. Nach dem Zahnverlust setzt die Wundheilung als Sekundärheilung ein, während der sich die Alveole mit Blut füllt und sich ein Koagulum bildet. Anschließend erfolgt dessen Umwandlung in Knochengewebe und schließlich verstreicht die Alveole derart, dass sie makroskopisch nicht mehr erkannt werden kann. Der Zeitrahmen der knöchernen Konsolidierung des Kieferkammes ist im Detail wenig erforscht. Aufgrund des gehäuften Auftretens von AMTL in menschlichen Populationen, ist die Erarbeitung eines Zeitfensters, mit dessen Hilfe durch makroskopische Beobachtung des Knochens die Zeitspanne seit dem Zahnverlust („time since tooth loss“, TSL) ermittelt werden kann, insbesondere im archäologischen Kontext äußerst wertvoll. Solch ein Zeitschema mit Angaben über die Variabilität der zeitlichen Abläufe bei den Heilungsvorgängen kann nicht nur in der Osteologie, sondern auch in der Forensik, der allgemeinen Zahnheilkunde und der Implantologie nutzbringend angewandt werden. rnrnNach dem Verlust eines Zahnes wird das Zahnfach in der Regel durch ein Koagulum aufgefüllt. Das sich bildende Gewebe wird rasch in noch unreifen Knochen umgewandelt, welcher den Kieferknochen und auch die angrenzenden Zähne stabilisiert. Nach seiner Ausreifung passt sich das Gewebe schließlich dem umgebenden Knochen an. Das Erscheinungsbild des Zahnfaches während dieses Vorgangs durchläuft verschiedene Stadien, welche in der vorliegenden Studie anhand von klinischen Röntgenaufnahmen rezenter Patienten sowie durch Untersuchungen an archäologischen Skelettserien identifiziert wurden. Die Heilungsvorgänge im Zahnfach können in eine prä-ossale Phase (innerhalb einer Woche nach Zahnverlust), eine Verknöcherungsphase (etwa 14 Wochen nach Zahnverlust) und eine ossifizierte bzw. komplett verheilte Phase (mindestens 29 Wochen nach Zahnverlust) eingeteilt werden. Etliche Faktoren – wie etwa die Resorption des Interdentalseptums, der Zustand des Alveolarknochens oder das Individualgeschlecht – können den normalen Heilungsprozess signifikant beschleunigen oder hemmen und so Unterschiede von bis zu 19 Wochen verursachen. Weitere Variablen wirkten sich nicht signifikant auf den zeitlichen Rahmen des Heilungsprozesse aus. Relevante Abhängigkeiten zwischen verschiedenen Variabeln wurden ungeachtet der Alveolenauffüllung ebenfalls getestet. Gruppen von unabhängigen Variabeln wurden im Hinblick auf Auffüllungsgrad und TSL in multivariablen Modellen untersucht. Mit Hilfe dieser Ergebnisse ist eine grobe Einschätzung der Zeitspanne nach einem Zahnverlust in Wochen möglich, wobei die Einbeziehung weiterer Parameter eine höhere Präzision ermöglicht. rnrnObwohl verschiedene dentale Pathologien in dieser Studie berücksichtigt wurden, sollten zukünftige Untersuchungen genauer auf deren potenzielle Einflussnahme auf den alveolaren Heilungsprozess eingehen. Der kausale Zusammenhang einiger Variablen (wie z. B. Anwesenheit von Nachbarzähnen oder zahnmedizinische Behandlungen), welche die Geschwindigkeit der Heilungsrate beeinflussen, wäre von Bedeutung für zukünftige Untersuchungen des oralen Knochengewebes. Klinische Vergleichsstudien an forensischen Serien mit bekannter TSL oder an einer sich am Anfang des Heilungsprozesses befindlichen klinischen Serie könnten eine Bekräftigung dieser Ergebnisse liefern.

Alveolar bone grafting in association with polyostotic fibrous dysplasia and bisphosphonate-induced abnormal bone turnover in a bilateral cleft lip and palate patient: a case report

A case is presented of extensive alveolar bone grafting in a patient with bilateral cleft lip and palate and polyostotic fibrous dysplasia. The patient previously underwent bisphosphonate therapy. Because of an abnormal and often decreased bone turnover caused by the fibrous dysplasia and the bisphosphonate therapy, bone grafting in such a patient poses several potential difficulties. In addition, the histomorphometric analysis of the bone grafts showed markedly decreased bone turnover. However, alveolar bone grafting using the iliac crest was performed successfully. Sufficient occlusion was achieved by postoperative low-loading orthodontic treatment.

Changes in the volume and density of calvarial split bone grafts after alveolar ridge augmentation

OBJECTIVES: One main problem occurring after bone grafting is resorption, leading to insufficient bone volume and quality, and may subsequently cause dental implant failure. Comparison of graft volume and bone density of iliac crest and calvarial transplants determined by animal studies demonstrates significantly lower resorption of bone grafts harvested from the skull. This paper is the first clinical study evaluating bone volume and density changes of calvarial split bone grafts after alveolar ridge reconstruction. MATERIAL AND METHODS: Bone volume and density were determined using CT scans and the software program Dicom Works in a total of 51 calvarial grafts after alveolar ridge augmentation in 15 patients. CT scans were taken in all 15 patients immediately after grafting (T0) and before implantation after a postoperative period of 6 months (T1). In five patients (26 calvarial grafts), a 1-year follow-up was performed (T2). RESULTS: A mean volume reduction of 16.2% at T1 (15 patients) and 19.2% at T2 (five patients) was observed. Bone density was high--about 1000 Hounsfield units--and did not change during the 1-year period. At the time of implantation, 41 transplants were classified as quality 1 bone and 10 as quality 2-3 bone. Grafting area and the technique used for grafting (inlay or onlay graft) did not affect the postoperative bone volume reduction. Generalized osteoporosis did not increase the resorption rate of calvarial transplants. CONCLUSION: Based on these findings, calvarial split bone grafts are a promising alternative for alveolar ridge reconstruction in dental implantology.

Computer-aided operation planning and 3-dimensional osteotomy guidance for alveolar distraction

Objectives: In alveolar distraction, in cases of severe atrophy in particular, it is often difficult to perform osteotomies in order to make a transport segment in optimal size and shape. Moreover care must be taken, not to damage the closely locating anato- mical structures such as the maxillary sinus, the inferior alveolar nerve, and the roots of the neighboring teeth. For setting ideal osteotomy lines exactly, we have developed a CT-based preoperative planning tool. Methods: 3-dimensional visual reconstruction of the jaw is created from the preoperative CT scans (1.0-mm slice thick- ness). Using the image-processing software Mimics (Materialise, Yokohama, Japan), various procedures of virtual cutting are simulated first to determine optimal osteotomy lines and to design an ideal transport segment. After the computer planning, data from the virtual solid model are transferred to a rapid prototype model, and a guiding splint is made to transfer the planned surgical simulation to the actual surgery. Results: The method was used in a case of severe atrophy of the anterior maxilla. The patient had a large maxillary sinus requir- ing a precise osteotomy in this critical area. Using the splint allowing a 3-dimensional guidance, alveolar osteotomies were easily done to achieve a transport segment in sufficient dimen- sion as planned, and any perforation of the maxillary sinus could be avoided. Finally the alveolar distraction of 10mm has suc- cessfully been performed. Conclusion: The preoperative planning method and the guiding splint described here are useful in problematic cases requiring an extremely precise osteotomy due to lack of bony space.

Anterior superior alveolar nerve (ASAN): A morphometric-anatomical Analysis

The anterior superior alveolar nerve (ASAN) is a branch of the infraorbital nerve. Only few studies have morphometrically evaluated the course of the ASAN. Midfacial segments of ten hemisectioned fresh adult cadaver heads were dissected to uncover the anterior wall of the maxilla. Specimens were subsequently decalcified and the bone overlying the ASAN was removed under a microscope to expose the ASAN. Its branching pattern from the infraorbital nerve was recorded, and the course of the ASAN within the anterior wall of the maxillary sinus was morphometrically assessed measuring distances to predefined landmarks using a digital caliper. A distinct ASAN was observed in all specimens. It arose lateral (six cases) or inferior (four cases) from the infraorbital nerve. The point of origin was located at a mean distance of 12.2 ± 5.79 mm posterior to the infraorbital foramen. The ASAN was located on average 2.8 ± 5.13 mm lateral to the infraorbital foramen. After coursing medially, the ASAN ran inferior to the foramen at a mean distance of 5.5 ± 3.07 mm. When approaching the nasal aperture, the loop of the ASAN was on average 13.6 ± 3.07 mm above the nasal floor. The horizontal mean distance from the ASAN to the nasal aperture was 4.3 ± 2.74 mm halfway down from the loop, and 3.3 ± 2.60 mm at the floor of the nose, respectively. In conclusion, the present study evaluated the course of the ASAN relative to the infraorbital foramen and nasal aperture. This information is helpful to avoid damage to this anatomical structure during interventions in the infraobrital region of the maxilla. Further, knowledge of the course of the ASAN and of its bony correlate (canalis sinuosus) may be valuable in interpreting anesthetic or radiologic findings in the anterior maxilla.

Correção de colapsos da crista alveolar com tecidos duros

Introdução: Uma adequada planificação é condição sine qua non para o êxito do tratamento com implantes. No entanto, nem sempre a colocação dos implantes na posição tridimensional ideal é, logo à partida, viável. Neste contexto, a correção dos colapsos da crista óssea com tecidos duros assume especial importância. Objetivos: O objetivo desta revisão narrativa é avaliar a eficácia dos diversos procedimentos existentes para aumento do rebordo com tecidos duros, de forma a facilitar a escolha do tratamento ideal. Materiais e Métodos: Pesquisou-se nas bases de dados MEDLINE, B-on e Google Académico. As palavras-chave utilizadas foram: “guided bone regeneration”, “ridge augmentation”, “seibert classification”, “alveolar bone splitting”, “horizontal bone augmentation” e “vertical bone augmentation”. Deu-se especial ênfase a revisões sistemáticas e meta-análises. A pesquisa foi limitada a artigos publicados em inglês, espanhol e em português até abril de 2016. Foram ainda consultados os livros “Tratado de Periodontia Clínica e Implantologia Oral” de Lindhe et al. (2005), “Implantes Dentais Contemporâneos” de Misch et al. (2009) e “Reabilitação com implantes endo-ósseos” de Alcoforado et al. (2008). Resultados: De um modo geral, todos os procedimentos analisados obtiveram altas taxas de sobrevivência aquando da reabilitação com implantes. No entanto, não houve diferenças significativas entre as diversas técnicas que possam levar a uma conclusão relevante sobre qual a melhor técnica a utilizar para este tipo de procedimento. Conclusão: Há evidências insuficientes para sugerir qual a técnica que deve ser preferida para o aumento de rebordo com tecidos duros, pelo que mais estudos são necessários.

A strain criterion for pull-through failures in crest-fixed steel claddings

Crest-fixed steel claddings made of thin, high strength steel often suffer from local pull-through failures at their screw connections during high wind events such as storms and hurricanes. Adequate design provisions are not available for these cladding systems except for the expensive testing provisions. Since the local pull-through failures in the less ductile steel claddings are initiated by transverse splitting at the fastener holes, numerical studies have not been able to determine the pull-through failure loads. Numerical studies could be used if a reliable splitting criterion is available. Therefore a series of two-span cladding and small scale tests was conducted on a range of crest-fixed steel cladding systems under simulated wind uplift loads. The strains in the sheeting around the critical central support screw fastener holes were measured until the pull-through failure occurred. This paper presents the details of the experimental investigation and the results including a strain criterion for the local pull-through failures in crest-fixed steel claddings.

Comparison of human alveolar osteoblasts cultured on polymer-ceramic composite scaffolds and tissue culture plates

The effects of medical grade polycaprolactone–tricalcium phosphate (mPCL–TCP) (80:20) scaffolds on primary human alveolar osteoblasts (AOs) were compared with standard tissue-culture plates. Of the seeded AOs, 70% adhered to and proliferated on the scaffold surface and within open and interconnected pores; they formed multi-layered sheets and collagen fibers with uniform distribution within 28 days. Elevation of alkaline phosphatase activity occurred in scaffold–cell constructs independent of osteogenic induction. AO proliferation rate increased and significant decrease in calcium concentration of the medium for both scaffolds and plates under induction conditions were seen. mPCL–TCP scaffolds significantly influenced the AO expression pattern of osterix and osteocalcin (OCN). Osteogenic induction down-regulated OCN at both RNA and protein level on scaffolds (3D) by day 7, and up-regulated OCN in cell-culture plates (2D) by day 14, but OCN levels on scaffolds were higher than on cell-culture plates. Immunocytochemical signals for type I collagen, osteopontin and osteocalcin were detected at the outer parts of scaffold–cell constructs. More mineral nodules were found in induced than in non-induced constructs. Only induced 2D cultures showed nodule formation. mPCL–TCP scaffolds appear to stimulate osteogenesis in vitro by activating a cellular response in AO's to form mineralized tissue. There is a fundamental difference between culturing AOs on 2D and 3D environments that should be considered when studying osteogenesis in vitro.

Bone response to unloaded titanium implants in the fibula, iliac crest, and scapula: an animal study in the Yorkshire pig

The reconstruction of extended maxillary and mandibular defects with prefabricated free flaps is a two stage procedure, that allows immediate function with implant supported dentures. The appropriate delay between prefabrication and reconstruction depends on the interfacial strength of the bone–implant surface. The purpose of this animal study was to evaluate the removal torque of unloaded titanium implants in the fibula, the scapula and the iliac crest. Ninety implants with a sandblasted and acid-etched (SLA) surface were tested after healing periods of 3, 6, and 12 weeks, respectively. Removal torque values (RTV) were collected using a computerized counterclockwise torque driver. The bicortical anchored 8 mm implants in the fibula revealed values of 63.73 Ncm, 91.50 Ncm, and 101.83 Ncm at 3, 6, and 12 weeks, respectively. The monocortical anchorage in the iliac crest showed values of 71.40 Ncm, 63.14 Ncm, and 61.59 Ncm with 12 mm implants at the corresponding times. The monocortical anchorage in the scapula demonstrated mean RTV of 62.28 Ncm, 97.63 Ncm, and 99.7 Ncm with 12 mm implants at 3, 6, and 12 weeks, respectively. The study showed an increase of removal torque with increasing healing time. The interfacial strength for bicortical anchored 8 mm implants in the fibula was comparable to monocortical anchored 12 mm implants in the iliac crest and the scapula at the corresponding times. The resistance to shear seemed to be determined by the type of anchorage (monocortical vs. bicortical) and the length of the implant with greater amount of bone–implant interface.