Interference of Two Closely Spaced Strip Footings on Sand Using Model Tests

By using small scale model tests, the interference effect on the ultimate bearing capacity of two closely spaced strip footings, placed on the surface of dry sand, was investigated. At any time, the footings were assumed to (1) carry exactly the same magnitude of load; and (2) settle to the same extent. No tilt of the footing was allowed. The effect of clear spacing (s) between two footings was explicitly studied. An interference of footings leads to a significant increase in their bearing capacity; the interference effect becomes even more substantial with an increase in the relative density of sand. The bearing capacity attains a peak magnitude at a certain (critical) spacing between two footings. The experimental observations presented in this technical note were similar to those given by different available theories. However, in a quantitative sense, the difference between the experiments and theories was seen to be still significant and it emphasizes the need of doing a further rigorous analysis in which the effect of stress level on the shear strength parameters of soil mass can be incorporated properly.

Energy-based motion control of a slender hull unmanned underwater vehicle

This paper presents a motion control system for tracking of attitude and speed of an underactuated slender-hull unmanned underwater vehicle. The feedback control strategy is developed using the Port-Hamiltonian theory. By shaping of the target dynamics (desired dynamic response in closed loop) with particular attention to the target mass matrix, the influence of the unactuated dynamics on the controlled system is suppressed. This results in achievable dynamics independent of stable uncontrolled states. Throughout the design, the insight of the physical phenomena involved is used to propose the desired target dynamics. Integral action is added to the system for robustness and to reject steady disturbances. This is achieved via a change of coordinates that result in input-to-state stable (ISS) target dynamics. As a final step in the design, an anti-windup scheme is implemented to account for limited actuator capacity, namely saturation. The performance of the design is demonstrated through simulation with a high-fidelity model.

Microbiological status of piggery effluent from 13 piggeries in the south east Queensland region of Australia

Aims: To assist in the development of safe piggery effluent re-use guidelines by determining the level of selected pathogens and indicator organisms in the effluent ponds of 13 south-east Queensland piggeries. Methods and Results: The numbers of thermotolerant coliforms, Campylobacter jejuni/coli, Erysipelothrix rhusiopathiae, Escherichia coli, Salmonella and rotavirus were determined in 29 samples derived from the 13 piggeries. The study demonstrated that the 13 final effluent ponds contained an average of 1Æ2 · 105 colony-forming units (CFU) 100 ml)1 of thermotolerant coliforms and 1Æ03 · 105 CFU 100 ml)1 of E. coli. The Campylobacter level varied from none detectable (two of 13 piggeries) to a maximum of 930 most probable number (MPN) 100 ml)1 (two of 13 piggeries). Salmonella was detected in the final ponds of only four of the 13 piggeries and then only at a low level (highest level being 51 MPN 100 ml)1). No rotavirus and no Erysip. rhusiopathiae were detected. The average log10 reductions across the ponding systems to the final irrigation pond were 1Æ77 for thermotolerant coliforms, 1Æ71 for E. coli and 1Æ04 for Campylobacter. Conclusions: This study has provided a baseline knowledge on the levels of indicator organisms and selected pathogens in piggery effluent. Significance and Impact of the Study: The knowledge gained in this study will assist in the development of guidelines to ensure the safe and sustainable re-use of piggery effluent.

Curing Reactions in Elastomers. 11. Carboxy- Terminated Polybutadiene

Attempts have been made to understand the curing reactions in carboxy-terminated polybutadiene (CTPB), which happens to be the most practical binder in advanced solid composite propellants. The curing of CTPB has been studied for different ratios of curing agents (MAPO and Epoxide) by gel content, molecular weight, crosslink density, and penetration temperature measurements, and the optimum composition of curators for effective curing of CTPB has been determined. Activation energy calculations on the curing of CTPB with 9.5% epoxide and 0.5% MAPO in the temperature range 75100°C gave 14.1 kcal/mol for which a diffusion-controlled or acid-catalyzed epoxide ring opening mechanism has been suggested for the curing process in CTPB.

Rapid and sensitive detection of Avibacterium paragallinarum in the presence of other bacteria using a 5' Taq nuclease assay: A new tool for diagnosing infectious coryza

A 5' Taq nuclease assay specific for Avibacterium paragallinarum was designed and optimized for use in diagnosing infectious coryza. The region chosen for assay design was one of known specificity for Av. paragallinarum. The assay detected Av. paragallinarum reference strains representing the three Page and the eight Kume serovars, and field isolates from diverse geographical locations. No cross-reactions were observed with other Avibacterium species, with other bacteria taxonomically related to Av. paragallinarum nor with bacteria and viruses likely to be present in swabs collected from suspected infectious coryza cases. The detection limit for the assay was 6 to 60 colony-forming units per reaction. Twenty-two out of 53 swabs collected from sick birds reacted in the 5' Taq nuclease assay, whereas Av. paragallinarum was not isolated from any of the swabs. All of the 22 swabs yielded other bacteria in culture. The presence of Av. paragallinarum in the swabs was also demonstrated by sequencing, thereby confirming the ability of the assay to detect Av. paragallinarum in the presence of other bacteria. The ability to quantify bacterial load in the swabs using the 5' Taq nuclease assay was demonstrated.

Genome-wide association meta-analysis identifies new endometriosis risk loci

We conducted a genome-wide association meta-analysis of 4,604 endometriosis cases and 9,393 controls of Japanese and European ancestry. We show that rs12700667 on chromosome 7p15.2, previously found to associate with disease in Europeans, replicates in Japanese (P = 3.6 x 10(-3)), and we confirm association of rs7521902 at 1p36.12 near WNT4. In addition, we establish an association of rs13394619 in GREB1 at 2p25.1 with endometriosis and identify a newly associated locus at 12q22 near VEZT (rs10859871). Excluding cases of European ancestry of minimal or unknown severity, we identified additional previously unknown loci at 2p14 (rs4141819), 6p22.3 (rs7739264) and 9p21.3 (rs1537377). All seven SNP effects were replicated in an independent cohort and associated at P <5 x 10(-8) in a combined analysis. Finally, we found a significant overlap in polygenic risk for endometriosis between the genome-wide association cohorts of European and Japanese descent (P = 8.8 x 10(-11)), indicating that many weakly associated SNPs represent true endometriosis risk loci and that risk prediction and future targeted disease therapy may be transferred across these populations.

Molecular and Cellular Mechanisms Behind Juvenile Neuronal Ceroid Lipofuscinosis (JNCL, Batten disease)

Neurodegenerative disorders are chronic, progressive, and often fatal disorders of the nervous system caused by dysfunction, and ultimately, death of neuronal cells. The underlying mechanisms of neurodegeneration are poorly understood, and monogenic disorders can be utilised as disease models to elucidate the pathogenesis. Juvenile neuronal ceroid-lipofuscinosis (JNCL, Batten disease) is a recessively inherited lysosomal storage disorder with progressive neurodegeneration and accumulation of autofluorescent storage material in most tissues. It is caused by mutations in the CLN3 gene; however, the exact function of the corresponding CLN3 protein, as well as the molecular mechanisms of JNCL pathogenesis have remained elusive. JNCL disease exclusively affects the central nervous system leaving other organs unaffected, and therefore it is of a particular importance to conduct studies in brain tissue and neuronal cells. The aim of this thesis project was to elucidate the molecular and cell biological mechanisms underlying JNCL. This was the first study to describe the endogenous Cln3 protein, and it was shown that Cln3 localised to neuronal cells in the mouse brain. At a subcellular level, endogenous Cln3 was localised to the presynaptic terminals and to the synaptosome compartment, but not to the synaptic vesicles. Studies with the CLN3-deficient cells demonstrated an impaired endocytic membrane trafficking, and established an interconnection between CLN3, microtubulus-binding Hook1 and Rab proteins. This novel data was not only important in characterising the roles of CLN3 in cells, but also provided significant information delineating the versatile role of the Rab proteins. To identify affected cellular pathways in JNCL, global gene expression profiling of the knock-out mouse Cln3-/- neurons was performed and systematically analysed; this revealed a slight dysfunction of the mitochondria, cytoskeletal abnormality in the microtubule plus-end, and an impaired recovery from depolarizing stimulus when specific N-type Ca2+ channels were inhibited, thus leading to a prolonged time of higher intracellular calcium. All these defective pathways are interrelated, and may together be sufficient to initiate the neurodegenerative process. Results of this thesis also suggest that in neuronal cells, CLN3 most likely functions at endocytic vesicles at the presynaptic terminal, potentially involved in the regulation of the calcium-mediated synaptic transmission.

Stochastic model for simulating maize yield

Maize is one of the most important crops in the world. The products generated from this crop are largely used in the starch industry, the animal and human nutrition sector, and biomass energy production and refineries. For these reasons, there is much interest in figuring the potential grain yield of maize genotypes in relation to the environment in which they will be grown, as the productivity directly affects agribusiness or farm profitability. Questions like these can be investigated with ecophysiological crop models, which can be organized according to different philosophies and structures. The main objective of this work is to conceptualize a stochastic model for predicting maize grain yield and productivity under different conditions of water supply while considering the uncertainties of daily climate data. Therefore, one focus is to explain the model construction in detail, and the other is to present some results in light of the philosophy adopted. A deterministic model was built as the basis for the stochastic model. The former performed well in terms of the curve shape of the above-ground dry matter over time as well as the grain yield under full and moderate water deficit conditions. Through the use of a triangular distribution for the harvest index and a bivariate normal distribution of the averaged daily solar radiation and air temperature, the stochastic model satisfactorily simulated grain productivity, i.e., it was found that 10,604 kg ha(-1) is the most likely grain productivity, very similar to the productivity simulated by the deterministic model and for the real conditions based on a field experiment. © 2012 American Society of Agricultural and Biological Engineers.

Crusted scabies is associated with increased IL-17 secretion by skin T cells

Scabies is an ectoparasitic infestation by the mite Sarcoptes scabiei. Although commonly self-limiting, a fraction of patients develop severely debilitating crusted scabies. The immune mechanisms underlying the development of crusted scabies are unclear, and undertaking longitudinal infection studies in humans is difficult. We utilized a porcine model to compare cellular immune responses in peripheral blood and skin of pigs with different clinical manifestations of scabies (n = 12), and in uninfected controls (n = 6). Although clinical symptoms were not evident until at least 4 weeks post-infestation, the numbers of peripheral IFNγ-secreting CD4+ T cells and γδ T cells increased in infected pigs from week 1 post-infestation. γδ T cells remained increased in the blood at week 15 post-infestation. At week 15, skin cell infiltrates from pigs with crusted scabies had significantly higher CD8+ T cell, γδ T cell and IL-17+ cell numbers than those with ordinary scabies. Peripheral IL-17 levels were not increased, suggesting that localized skin IL-17-secreting T cells may play a critical role in the pathogenesis of crusted scabies development. Given the potential of anti-IL-17 immunotherapy demonstrated for other inflammatory skin diseases, this study may provide a novel therapeutic avenue for patients with recurrent crusted scabies.

Enterprise education: The frustration of a pure contest

Purpose This paper discusses the development of a strategy game for enterprise education. It is argued that requiring students to initially struggle with the game’s rules and strategies results in a worthwhile test of their persistence and ability to manage ambiguity. Further, that in the absence of uncertainty, students will not benefit from the game’s potential contribution to their overall learning. Approach The paper is constructed around the infusion of student narratives and the author’s self-reflective thoughts. The papers explores the process of developing a game that; - 1) provides the students with access to an enterprise reality, - 2) strengthens their engagement with the theoretical foundations of their studies, and; - 3) provides a process for serious self-reflection. Findings Despite the mixed views presented in this paper, the game’s development thus far has been very successful. Students do enjoy and benefit from enduring the frustration of a pure contest. Having to work through uncertainty is a good practice for students in Higher Education, especially those engaged in enterprise education. Practical Implications Whilst the use of games in experiential education is not uncommon, consideration of how and why they are developed is not always well understood. This paper suggests that enterprise educators have significant opportunities to develop games that genuinely provide student access to the entrepreneur’s way of life. Value of Paper This paper provides evidence of how a game can be constructed to add significant value to an existing curriculum. It also provides evidence of the inner thoughts of students frustrated by a challenge they refuse to give up on. As such, it provides a valuable window through which to contemplate the minds of tomorrow’s nascent entrepreneurs.

The Structure of Monosodium Phosphoenolpyruvate

CDH406P-.Na +.H20 , M r = 208.0, is monoclinic, Cc, a = 11.423 (2), b = 23.253 (5), c - 6.604 (1) A, fl = 123.63 (1) °, U = 1460.6 A 3, D x =. 1.89 Mg m -a, Z = 8, 2(Mo Ka) = 0.7107 A, p(Mo Ka) = 0.44 mm -~, F(000) = 840. Final R = 0.063 for 1697 reflections.The two crystallographically independent molecules of phosphoenolpyruvate (PEP) (A and B) are almost mirror images of each other, the mirror being the planar enolpyruvate group. The torsion angle C(3)-C(2)- O(1)-P(1) is 122.6 in A and -112.0 ° in B, in contrast to -209.1 ° in PEP.K. The enolic C(2)-O(1) has a partial double-bond character [1.401 (A), 1.386A (B)]. The high-energy P~O bond (1.595 and 1.610A) is comparable to that in PEP.K (1.612 A). Na(1) has six nearest neighbours while Na(2) has only five. The Na + ions are involved in binding only the phosphates of different molecules, in contrast to the K ÷ ion in PEP. K, which binds to both the phosphate and carboxyl ends of the same molecule. The planar carboxyl groups stack on each other at an average distance of 3.2 A instead of forming hydrogen-bonded dimers usually found in carboxylate structures.

Small-scale capture, transport and tank adaptation of live, medium-sized Scombrids using "Tuna Tubes"

The transport of live fish is a crucial step to establish fish culture in captivity, and is especially challenging for species that have not been commonly cultured before, therefore transport and handling methods need to be optimized and tailored. This study describes the use of tuna tubes for small-scale transport of medium-sized pelagic fish from the Scombridae family. Tuna tubes are an array of vertical tubes that hold the fish, while fresh seawater is pumped up the tubes and through the fish mouth and gills, providing oxygen and removing wastes. In this study, 19 fish were captured using rod and line and 42% of the captured fish were transported alive in the custom-designed tuna tubes to an on-shore holding tank: five mackerel tuna (Euthynnus affinis) and three leaping bonito (Cybiosarda elegans). Out of these, just three (15.8% of total fish) acclimatized to the tank's condition. Based on these results, we discuss an improved design of the tuna tubes that has the potential to increase survival rates and enable a simple and low cost method of transporting of live pelagic fish.

A model Integrating the Facilities Management Process with the Building End User’s Business Process (ProFacil)

The ProFacil model is a generic process model defined as a framework model showing the links between the facilities management process and the building end user’s business process. The purpose of using the model is to support more detailed process modelling. The model has been developed using the IDEF0 modelling method. The ProFacil model describes business activities from the generalized point of view as management-, support-, and core processes and their relations. The model defines basic activities in the provision of a facility. Examples of these activities are “operate facilities”, “provide new facilities”, “provide re-build facilities”, “provide maintained facilities” and “perform dispose of facilities”. These are all generic activities providing a basis for a further specialisation of company specific FM activities and their tasks. A facilitator can establish a specialized process model using the ProFacil model and interacting with company experts to describe their company’s specific processes. These modelling seminars or interviews will be done in an informal way, supported by the high-level process model as a common reference.

Reactivity Of Pph3 Toward Ruiiruiiicl(O2car)4 - Syntheses, Molecular-Structures, And Spectroscopic And Electrochemical Properties Of Ruiiruiii(Oh2)Cl(Mecn)(O2car)4(Pph3)2 And Ruii2(Oh2)(Mecn)2(O2car)4(Pph3)2

By the reaction of Ru2Cl(O2CAr)4 (1) and PPh3 in MeCN-H2O the diruthenium(II,III) and diruthenium(II) compounds of the type Ru2(OH2)Cl(MeCN)(O2CAr)4(PPh3)2 (2) and Ru2(OH2)(MeCN)2(O2CAr)4(PPh3)2 (3) were prepared and characterized by analytical, spectral, and electrochemical data (Ar is an aryl group, C6H4-p-X; X = H, OMe, Me, Cl, NO2). The molecular structure of Ru2(OH2)Cl(MeCN)(O2CC6H4-p-OMe)4(PPh3)2 was determined by X-ray crystallography. Crystal data are as follows: triclinic, P1BAR, a = 13.538 (5) angstrom, b = 15.650 (4) angstrom, c = 18.287 (7) angstrom, alpha = 101.39 (3)-degrees, beta = 105.99 (4)-degrees, gamma = 97.94 (3)-degrees, V = 3574 angstrom 3, Z = 2. The molecule is asymmetric, and the two ruthenium centers are clearly distinguishable. The Ru(III)-Ru(II), Ru(III)-(mu-OH2), and Ru(II)-(mu-OH2) distances and the Ru-(mu-OH2)-Ru angle in [{Ru(III)Cl(eta-1-O2CC6H4-p-OMe)(PPh3)}(mu-OH2)(mu-O2CC6H4-p-OMe)2{Ru(II)(MeCN)(eta-1-O2CC6H4-p-OMe)(PPh3)}] are 3.604 (1), 2.127 (8), and 2.141 (10) angstrom and 115.2 (5)-degrees, respectively. The compounds are paramagnetic and exhibit axial EPR spectra in the polycrystalline form. An intervalence transfer (IT) transition is observed in the range 900-960 nm in chloroform in these class II type trapped mixed-valence species 2. Compound 2 displays metal-centered one-electron reduction and oxidation processes near -0.4 and +0.6 V (vs SCE), respectively in CH2Cl2-TBAP. Compound 2 is unstable in solution phase and disproportionates to (mu-aquo)diruthenium(II) and (mu-oxo)diruthenium(III) complexes. The mechanistic aspects of the core conversion are discussed. The molecular structure of a diruthenium(II) compound, Ru2(OH2)(MeCN)2(O2CC6H4-p-NO2)4(PPh3)2.1.5CH2Cl2, was obtained by X-ray crystallography. The compound crystallizes in the space group P2(1)/c with a = 23.472 (6) angstrom, b = 14.303 (3) angstrom, c = 23.256 (7) angstrom, beta = 101.69 (2)-degrees, V = 7645 angstrom 3, and Z = 4. The Ru(II)-Ru(II) and two Ru(II)-(mu-OH2) distances and the Ru(II)-(mu-OH2)-Ru(II) angle in [{(PPh3)-(MeCN)(eta-1-O2CC6H4-p-NO2)Ru}2(mu-OH2)(mu-O2CC6H4-p-NO2)2] are 3.712 (1), 2.173 (9), and 2.162 (9) angstrom and 117.8 (4)-degrees, respectively. In both diruthenium(II,III) and diruthenium(II) compounds, each metal center has three facial ligands of varying pi-acidity and the aquo bridges are strongly hydrogen bonded with the eta-1-carboxylato facial ligands. The diruthenium(II) compounds are diamagnetic and exhibit characteristic H-1 NMR spectra in CDCl3. These compounds display two metal-centered one-electron oxidations near +0.3 and +1.0 V (vs SCE) in CH2Cl2-TBAP. The overall reaction between 1 and PPh3 in MeCN-H2O through the intermediacy of 2 is of the disproportionation type. The significant role of facial as well as bridging ligands in stabilizing the core structures is observed from electrochemical studies.