Turkey's Accession to the European Union in terms of impact on the EU's security and defense policies: potential and drawbacks

This study explores the impact of Turkey's likely entry in the European Union (EU) in terms of the EU's foreign, security and defense policies. It reviews Turkish capabilities, namely its military capabilities, which could provide the EU with valuable defense assets. There are differences related to Turkey's relations with the EU, which have increasingly spilled over into the NATO, hindering the development of cooperation over crisis management operations. The article then delves in the implications of Turkey's strategic geographical location to EU policies. It reviews how far the EU and Turkey may have convergent interests in some of the neighboring regions, especially in the Middle East.

Brazil's rise on the international scene: Brazil and the World

Since Cardoso and during Lula's Administration, the international order has undergone significant changes. These changes have allowed the Brazilian foreign policy to mitigate internal effects of an order established by others and, at the same time, to become an active participant in the formulation of the new order. To democratize globalization became the mainspring of Brazilian foreign policy. In the scope, President Lula has maintained the tradition of formulating and programming foreign policy as a State policy, and also has fostered the logistic strategy of incorporation of Brazil into the international scene.

Considerations about the recommendations of the Commission on the Limits of the Continental Shelf on the Amazon fan

In 2004, Brazil submitted to the Commission on the Limits of the Continental Shelf (CLCS) a Submission for the outer limit of the Brazilian continental shelf for its extension beyond the limits of 200 nautical miles. In 2007, the CLCS presented its recommendations, however it did not recommend four areas proposed by Brazil, the Amazon Fan among them. The objective of this study is to present the main legal and technical aspects of the controversy about the Amazon Fan, in order to evaluate some alternatives for a future submission, new or revised.

The influence of light spectra, UV-A, and growth regulators on the in vitro seed germination of Senecio cineraria DC.

This study was carried out to investigate the effects of light spectra, additional UV-A, and different growth regulators on the in vitro germination of Senecio cineraria DC. Seeds were surface-sterilized and inoculated in MS medium to evaluate the following light spectra: white, white plus UV-A, blue, green, red or darkness. The maximum germinability was obtained using MS0 medium under white light (30%) and MS + 0.3 mg L-1 GA3 in the absence of light (30.5%). S. cineraria seeds were indifferent to light. Blue and green lights inhibited germination. Different concentrations of gibberellic acid (GA3) (0.1; 0.4; 0.6; 0.8; 1.0 and 2.0 mg L-1) and indole-3-acetic acid IAA (0.1; 0.3 and 1.0 mg L-1) were evaluated under white light and darkness. No concentration of GA3 enhanced seed germination percentage under white light. However, when the seeds were maintained in darkness, GA3 improved germination responses in all tested concentrations, except at 1.0 mg L-1. Under white light, these concentrations also increased the germination time and reduced germination rate. Germination rate, under light or darkness, was lower using IAA compared with GA3.

Fiber average size and distribution dependence on the electrospinning parameters of poly(vinylidene fluoride trifluoroethylene)) membranes for biomedical applications

Poly(vinylidene fluoride-trifluoethylene) electrospun membranes were obtained from a blend of dimethylformamide (DMF) and methylethylketone (MEK) solvents. The inclusion of the MEK to the solvent system promotes a faster solvent evaporation allowing complete polymer crystallization during the jet travelling between the tip and the grounded collector. Several processing parameters were systematically changed to study their influence on fiber dimensions. Applied voltage and inner needle diameter do not have large influence on the electrospun fiber average diameter but in the fiber diameter distribution. On the other hand, the increase of the distance between the needle tip to collector results in fibers with larger average diameter. Independently on the processing conditions, all mats are produced in the electroactive phase of the polymer. Further, MC-3T3-E1cell adhesion was not inhibited by the fiber mats preparation, indicating their potential use for biomedical applications.

On the origin of the electrical response of vapor grown carbon nanofiber + epoxy composites

The origin of the electrical response of vapor grown carbon nanofiber (VGCNF) + epoxy composites is investigated by studying the electrical behavior of VGCNF with resin, VGCNF with hardener and cured composites, separately. It is demonstrated that the onset of the conductivity is associated to the emergence of a weak disorder regime. It is also shown that the weak disorder regime is related to a hopping depending on the physical properties of the polymer matrix.

Effect of the Impact Conditions on the Mechanical Properties of Injection-Molded Parts

This work focused on the study of the impact event on molded parts in the framework of automotive components. The influence of the impact conditions and processing parameters on the mechanical behavior of talc-filled polypropylene specimens was analyzed. The specimens were lateral-gate discs produced by injection molding, and the mechanical characterization was performed through instrumented falling weight impact tests concomitantly assisted with high-speed videography. Results analyzed using the analysis of variance (ANOVA) method have shown that from the considered parameters, only the dart diameter and test temperature have significant influence on the falling weight impact properties. Higher dart diameter leads to higher peak force and peak energy results. Conversely, higher levels of test temperatures lead to lower values of peak force and peak energy. By means of high-speed videography, a more brittle fracture was observed for experiments with higher levels of test velocity and dart diameter and lower levels of test temperature. The injection-molding process conditions assessed in this study have an influence on the impact response of moldings, mainly on the deformation capabilities of the moldings.