Electrical instability in vanadyl-phthalocyanine thin-film transistors

We investigated the electrical instability of vanadyl-phthalocyanine (VOPc) thin-film transistors (TFTs) at various temperatures. The results demonstrate a slow threshold voltage shift in the bias stress process and a rapid recovery after the removal of bias stress, which indicates that a slower degradation process occurs in the on state while a faster removal in the off state of VOPc TFTs. The shift of threshold voltage comes from traps generated at the organic/dielectrics interface. Additionally, a relaxation time of 10(7) s was obtained at room temperature according to the stretched exponential model, which is comparable to a-Si: H TFTs. Therefore, VOPc TFTs are suitable to be applied in flat panel displays.

The dewetting dynamics of the polymer thin film by solvent annealing

The slippage effect of the polymer chains is investigated in the dewetting process of the polymer solution film. The solvent-induced dewetting is used in our experiments to study the dynamics of hole growth in the dewetting process of the polymer solution film. Our results show that in the case of the low molecular weight polystyrene (PS) film, the slippage effect of the polymer chains is not displayed and the radius of the holes is R similar to exp(t/tau); in the case of the higher molecular weight PS film, the slippage effect of the polymer chain is not valid in the case of the thin film and that is valid in the case of the thick film, and the dynamic process of hole growth divides into three stages (R similar to t, and then R similar to t(x) (2/3 < x < 1), finally, R similar to t). Besides, the solvent and substrate properties also influence the dewetting dynamics of the polymer solution film.

Novel thin-film composite membranes with improved water flux from sulfonated cardo poly(arylene ether sulfone) bearing pendant amino groups

A new class of polymeric amine, namely, sulfonated cardo poly(arylene ether sulfone) (SPES-NH2) was synthesized and used for the preparation of thin-film composite membrane. The TFC membranes were prepared on a polysulfone supporting film through interfacial polymerization with trimesoyl chloride (TMC) solutions and amine solutions containing SPES-NH2 and m-phenylenediamine (MPDA). The resultant membranes were characterized with water permeation performance, chemical structure, hydrophilicity of active layer and membrane morphology including top surface and cross-section.

Polyamide thin film composite membranes prepared from isomeric biphenyl tetraacyl chloride and m-phenylenediamine

Three novel of isomeric tetra-functional biphenyl acid chloride: 3,3',5,5'-biphenyl tetraacyl chloride (mm-BTEC), 2,2',4,4'-biphenyl tetraacyl chloride (om-BTEC), and 2,2',5,5'-biphenyl tetraacyl chloride (op-BTEC) were synthesized, and used as new monomers for the preparation of the thin film composite (TFC) reverse osmosis (RO) membranes through interfacial polymerization with m-phenylenediamine (MPDA). The results of membrane performance test showed that membranes prepared from om-BTEC and op-BTEC had higher flux at the expanse of rejection compared with membranes prepared from mm-BTEC.

Film Morphology and Molecular Orientation in Oligothiophene-fluorene Films

The effects of processing conditions on film morphology and molecular orientation were studied for a novel conjugated fluorene-bithiophene oligomer, oligo(9,9-dioctylfluorene-alt-bithiophene) (OF8T2). Depending on the method of film preparation, OF8T2 molecules adopt different orientations in the films. X-ray diffraction peak at 4.9 degrees of the OF8T2 film deposited from petroleum ether/dichloromethane mixture is attributed to a layering distance between sheets of OF8T2 chains, which are separated by the octyl side chains. Preferred orientation is clearly inferred through the absence of peaks corresponding to pi-pi stacking.