Análise das principais dificuldades dos alunos de uma turma do 2.º ano do 1º CEB na construção e interpretação de gráficos

Relatório Final apresentado para a obtenção de grau de mestre em Educação pré-escolar e ensino do 1º ciclo do ensino básico

Adutoras puras e mistas : análise técnico-económica

As adutoras são consideradas, por alguns autores, como sendo as principais componentes de um Sistema de Abastecimento de Água (SAA), dado o seu elevado custo e importância para o funcionamento desses sistemas. A sua função reside em transportar água desde as captações até aos reservatórios de distribuição. As adutoras são compostas por condutas que podem ser gravíticas (desnível favorável) ou por bombeamento (desnível desfavorável). Nas adutoras por bombeamento, dado que é necessário fornecer energia ao sistema para elevar água, os custos de exploração representam uma parcela muito importante dos custos globais destes sistemas adutores. Dada a crescente dimensão e complexidade dos sistemas de adução, face à tendência de crescimento dos consumos, nos últimos anos, a comunidade científica tem-se debruçado sobre o estudo destes sistemas, particularmente dos sistemas por bombeamento, tendo em vista a sua otimização, quer do seu dimensionamento quer da sua operação. Em Portugal, os SAA encontram-se separados em duas vertentes, nomeadamente, os sistemas em alta (captação, transporte e armazenamento) e os sistemas em baixa (distribuição). Nas últimas décadas, talvez fruto dessa divisão, assistiu-se ao abandono das adutoras mistas (com distribuição de percurso), em favor das adutoras puras (sem distribuição de percurso). No entanto, tal decisão não foi devidamente acompanhada de estudos de viabilidade técnico-económica que, fundamentadamente, pudessem justificar se essa decisão terá ou não sido acertada. Nesse sentido, esta dissertação pretende avaliar para dois exemplos práticos de adutoras por bombeamento, uma pura e outra mista, aplicando metodologias de otimização para o dimensionamento e a operação, quais os custos de investimento e de energia associados a cada um, por forma a aferir qual dos sistemas é de facto mais económico. Do estudo efetuado, foi possível concluir que a adutora mista apresenta um custo global significativamente inferior ao da adutora pura, contribuído para esse facto a redução considerável nos custos de energia elétrica para a operação do sistema e a redução do custo do troço de distribuição (desde o reservatório até à rede). Além do aspeto meramente económico, importa também referir que a redução dos custos de energia e do troço de distribuição traz também importantes vantagens do ponto de vista ambiental.

Competição espacial no mercado de revenda da gasolina: uma análise nas principais cidades do Rio Grande do Norte

This study aims to analyze the relationship between average price with the concentration in the markets (municipalities) in the state of Rio Grande do Norte, is using a little tool applied to the Brazilian market is the spatial econometric model. A data base contains all the stations of the major cities in the state of Rio Grande do Norte and includes 142 observations on stations was used. Theoretical models predict the relationship between the number of competitors in a market and the average price; these theoretical models include: the monopolistic competition of Perloff and Salop (1985), and the search-theoretic, of Carlson and McAfee (1983) and Varian (1980). The empirical results showed that a higher density within a geographic area is associated with a lower average price, thus converging with the monopolistic competition model and with the search-theoretic of Carlson and McAfee (1983). The parameters varied little with the inclusion / exclusion of control variables, showing the robustness of them.

Análise das principais variáveis na flotação industrial do complexo de mineração de Tapira - MG

Faced with an agribusiness expansion scenario and the increase in fertilizer consumption due to the exponential growth of the population, it is necessary to make better use of existing reserves, by obtaining products of better quality and in adequate quantities to meet demand national. In Tapira Mining Complex, Vale Fertilizantes, the phosphate concentrate is produced with content of 35.0% P2O5 from ore with content of about 8.0% P2O5, which are intended to supply Complex Industrial Uberaba and Araxá Minero Chemical Complex for the production of fertilizers. The industrial flotation step responsible for the recovery of P2O5 and hence the viability of the business is divided into the crumbly, grainy and ultrathin circuits, and, friable and granular concentrate comprise the conventional concentrated. Today only 14.7% of the mass which feeds the mill product becomes, the remainder being considered losses in the process, and the larger mass losses are located in the waste of flotation, representing 42.3%. From 2012 to 2014, the daily global mass recovery processing plants varied from 12.4 to 15.9% while the daily metallurgical recovery of P2O5 from 48.7 to 82.4%. By the degree of variability, it appears that the plant operated under different conditions. Seen this, this study aimed to analyze the influence of operational and process variables in P2O5 mass and metallurgical recoveries of industrial flotation circuits of grainy, crumbly and ultrathin. And besides was made an analysis of the effect of ore variables, as degrees, hardnesse and the ore front 02 percentage, in global recoveries of processing plant and the effect of dosages of reagents in the recoveries obtained from the bench flotation using the experimental design methodology. All work was performed using the historical database of Vale Fertilizantes of Tapira-MG, where all independent variables were dimensionless as the experimental range used. To make the statistical analysis it used the response surface technique and the values of the independent variables that maximize recoveries were found by canonical analysis. In the study of industrial flotation circuit crispy were obtained from 41.3% mass recovery and 91.3% metallurgical recovery P2O5, good values for the circuit, and the highest recoveries occur for solids concentration of the new flotation power between 45 and 50%, which values are assigned to the residence time of the pulp in cells and industrial flotation columns. The greater the number of ore heaps resumed on the higher the mass recovery, but in this scenario flotation becomes unstable because there is enormous weight variation in the feed. Higher recoveries are obtained for mass depressant dosage exceeding 120 g / t for synthetic collector dosage of 11.6%. In the study of industrial flotation circuit of the granulate were obtained 28.3% to 79.4% mass recovery and metallurgical recovery of P2O5 being considered good values for the circuit. Higher recoveries are obtained when the front ore 02 percentage is above 90%, because the ore of this front have more clear apatite. Likewise recoveries increase when the level of pulp rougher step is highest due to the high mass of circulating step receives loads. In the analysis of industrial flotation circuit of the ultrafine were obtained 23.95% of mass recovery, and the same is maximized to depressant dosage and the top collector 420 and 300 g / t, respectively. The analysis of the influence of variables ore, it was observed that higher recoveries are obtained for ores with P2O5 content above 8.0%, Fe2O3 content in the order of 28% forward and 02 of ore percentage of 83%. Hard ore percentage has strong influence on recoveries due to mass division in the circuit that is linked to this variable. However, the hard ore percentage that maximizes recoveries was very close to the design capacity of the processing plant, which is 20%. Finally, the study of the bench flotation, has noted that in friable and granular circuits the highest recoveries are achieved for a collector dosage exceeding 250 g / t and the simultaneous increase of collector dosage and synthetic collector percentage contributes to the increase recovery in the flotation, but this scenario is suitable to produce a concentrate poorer in terms of P2O5 content, showing that higher recovery is not always the ideal scenario. Thus, the results show the values of variables that provide higher recoveries in the flotation and hence lower losses in the waste.

Análise do contágio nos principais índices bolsistas europeu e norte-americano

Mestrado em Controlo de Gestão e dos Negócios

Projeto, implementação e análise de um conversor CC-CC de alto ganho e alto rendimento para aplicações fotovoltaicas

In recent years the photovoltaic generation has had greater insertion in the energy mix of the most developed countries, growing at annual rates of over 30%. The pressure for the reduction of pollutant emissions, diversification of the energy mix and the drop in prices are the main factors driving this growth. Grid tied systems plays an important role in alleviating the energy crisis and diversification of energy sources. Among the grid tied systems, building integrated photovoltaic systems suffers from partial shading of the photovoltaic modules and consequently the energy yield is reduced. In such cases, classical forms of modules connection do not produce good results and new techniques have been developed to increase the amount of energy produced by a set of modules. In the parallel connection technique of photovoltaic modules, a high voltage gain DC-DC converter is required, which is relatively complex to build with high efficiency. The current-fed isolated converters explored in this work have some desirable characteristics for this type of application, such as: low input current ripple and input voltage ripple, high voltage gain, galvanic isolation, feature high power capacity and it achieve soft switching in a wide operating range. This study presents contributions to the study of a high gain and high efficiency DC-DC converter for use in a parallel system of photovoltaic generation, being possible the use in a microinverter or with central inverter. The main contributions of this work are: analysis of the active clamping circuit operation proposing that the clamp capacitor connection must be done on the negative node of the power supply to reduce the input current ripple and thus reduce the filter requirements; use of a voltage doubler in the output rectifier to reduce the number of components and to extend the gain of the converter; detailed study of the converter components in order to raise the efficiency; obtaining the AC equivalent model and control system design. As a result, a DC-DC converter with high gain, high efficiency and without electrolytic capacitors in the power stage was developed. In the final part of this work the DC-DC converter operation connected to an inverter is presented. Besides, the DC bus controller is designed and are implemented two maximum power point tracking algorithms. Experimental results of full system operation connected to an emulator and subsequently to a real photovoltaic module are also given.

Análise mecânica e microestrutural das ligas de cobalto-cromo de uso odontológico após sucessivas refundições

The cobalt-chromium alloy is extensively used in the Odontology for the confection of metallic scaffolding in partial removable denture. During the last few years, it has been reported an increasing number of premature imperfections, with a few months of prosthesis use. The manufacture of these components is made in prosthetic laboratories and normally involves recasting, using parts of casting alloy and parts of virgin alloy. Therefore, the objective of the present study was to analyze the mechanical properties of a commercial cobalt-chromium alloy of odontological use after successive recasting, searching information to guide the dental prosthesis laboratories in the correct manipulation of the cobalt-chromium alloy in the process of casting and the possible limits of recasting in the mechanical properties of this material. Seven sample groups were confectioned, each one containing five test bodies, divided in the following way: G1: casting only with virgin alloy; G2: casting with 50% of the alloy of the G1 + 50% of virgin alloy; G3: casting with 50% of the alloy of the G2 + 50% of virgin alloy; G4: casting with 50% of the alloy of the G3 + 50% of virgin alloy; G5: 50% of alloy of the G4 + 50% of virgin alloy; G6: 50% of alloy of the G5 + 50% of virgin alloy and finally the G7, only with recasting alloy. The modifications in the mechanical behavior of the alloy were evaluated. Moreover, it was carried the micro structural characterization of the material by optic and electronic scanning microscopy, and X ray diffraction.and fluorescence looking into the correlatation of the mechanical alterations with structural modifications of the material caused by successive recasting process. Generally the results showed alterations in the fracture energy of the alloy after successive recasting, resulting mainly of the increasing presence of pores and large voids, characteristic of the casting material. Thus, the interpretation of the results showed that the material did not reveal significant differences with respect to the tensile strength or elastic limit, as a function of successive recasting. The elastic modulus increased from the third recasting cycle on, indicating that the material can be recast only twice. The fracture energy of the material decreased, as the number of recasting cycles increased. With respect to the microhardness, the statistical analyses showedno significant differences. Electronic scanning microscopy revealed the presence of imperfections and defects, resulting of the recasting process. X ray diffraction and fluorescence did not show alterations in the composition of the alloy or the formation of crystalline phases between the analyzed groups. The optical micrographs showed an increasing number of voids and porosity as the material was recast. Therefore, the general conclusion of this study is that the successive recasting of of Co-Cr alloys affects the mechanical properties of the material, consequently leading to the failure of the prosthetic work. Based on the results, the best recommendadition is that the use of the material should be limited to two recasting cycles