Experimental study of proton induced nuclear reactions in 6,7 Li

This work presents the results of the experimental study of proton induced nuclear reactions in lithium, namely the 7Li(p,α) 4He, 6Li(p,α) 3He and 7Li(p,p)7Li reactions. The amount of 7Li and 6Li identified as primordial and observed in very old stars of the Milky Way galactic halo strongly deviates from the predictions of primordial nucleosynthesis and stellar evolution models which depend, among other factors, on the cross sections of reactions like 7Li(p,α) 4He and 6Li(p,α) 3He. These discrepancies have triggered a large amount of research in the fields of stellar evolution, cosmology, pre-galactic evolution and low energy nuclear reactions. Focusing on nuclear reactions, this work has measured the 7Li(p,α) 4He and 6Li(p,α) 3He reactions cross sections (expressed in terms of the astrophysical S -factor) with higher accuracy, and the electron screening effects in these reactions for different environments (insulators and metallic targets). The 7Li(p,α) 4He angular distributions were also measured. These measurementstook place in two laboratory facilities, in the framework of the LUNA (Laboratory for Undergroud Nuclear Astrophysics) international collaboration, namely the Laboratorio ´ de Feixe de Ioes ˜ in ITN (Instituto Tecnologico ´ e Nuclear) Sacavem, ´ Portugal, and the Dynamitron-TandemLaboratorium in Ruhr-Universitat¨ Bochum, Germany. The ITN target chamber was modified to measure these nuclear reactions, with the design and construction of new components, the addition of one turbomolecular pump and a cold finger. The 7Li(p,α) 4He and 6Li(p,α) 3He reactions were measured concurrently with seven and four targets, respectively. These targets were produced in order to obtain adequate and stable lithium depth profiles. In metallic environments, the measured electron screening potential energies are much higher than the predictions of atomic-physics models. The Debye screening model applied to the metallic conduction electrons is able to explain these high values. It is a simple model, but also very robust. Concerning primordial nucleosynthesis and stellar evolution models, these results are very important as they show that laboratory measurements are well controlled, and the model inputs from these cross sections are therefore correct. In this work the 7Li(p,p)7Li differential cross section was also measured, which is useful to describe the 7Li(p,α) 4He entrance channel.

Estudo comparativo da estrutura de betão armado de um edifício dimensionada segunda a actual regulamentação nacional e os eurocódigos estruturais

Dissertação para obtenção do grau de Mestre em Engenharia Civil - Ramo de Estruturas

Notes sur la géologie et la paleontology du Miocène de Lisbonne

This note deals with the stratigraphical and paleontological study of the Palença section on the southern bank of the river Tagus, Portugal, and specially with its coccolithophorids. Three main lithostratigraphical units may be recognized: the lowest one does correspond to the upper part of COTTER's division II, the intermediate one to divisions III and IV-a, the third corresponding to pratically the whole division IV-b, However other and higher levels are also represented. Higher beds are also represented in the same sections; they are less well exposed and were not studied in detail. Caracterisation of biozones on the basis of Coccoliths so far found at Palença section is difficultsince MARTINI's zones have been defined mainly by forms of Discoaster and other genera that are wanting. However we can recognize that the richest assemblage (from beds 17-18, the uppermost layers of blue clays IV-a) may correspond to NN4. This is not in opposition to the results of the study of planctonic foraminifera, that are characteristic of BLOW's N7. Coccoliths from lower beds do not allow at present any valid comparisons.

Moradia no centro histórico do Montijo: reabilitação vs construção nova

Dissertação para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações

O Caloviano do flanco norte do Guilhim (Algarve oriental): biostratigrafia e paleobiogeografia

Stratigraphical study of Telheiro and Cancela sections (northern slope of Guilhim hill) allowed its dating: these may be reported to the Lower Callovian, as ammonite associations typical of Rehmanni and Pictava horizons have been collected there. Hence Gracilis zone can be recognized in Algarve. Ammonites are also associated to Dinoflagellates. These microfossils have been found for the first time in the Callovian of Portugal. Callovian paleogeogtaphy is reapprised, and the limits between mesogean submediterranean and mediterranean provinces are more accurately recognized. Algarve belongs to the mediterranean province according to the typically mesogean character of the fauna where Phylloceratidae are dominant.

A capacity sharing and stealing strategy for open real-time systems

This paper focuses on the scheduling of tasks with hard and soft real-time constraints in open and dynamic real-time systems. It starts by presenting a capacity sharing and stealing (CSS) strategy that supports the coexistence of guaranteed and non-guaranteed bandwidth servers to efficiently handle soft-tasks’ overloads by making additional capacity available from two sources: (i) reclaiming unused reserved capacity when jobs complete in less than their budgeted execution time and (ii) stealing reserved capacity from inactive non-isolated servers used to schedule best-effort jobs. CSS is then combined with the concept of bandwidth inheritance to efficiently exchange reserved bandwidth among sets of inter-dependent tasks which share resources and exhibit precedence constraints, assuming no previous information on critical sections and computation times is available. The proposed Capacity Exchange Protocol (CXP) has a better performance and a lower overhead when compared against other available solutions and introduces a novel approach to integrate precedence constraints among tasks of open real-time systems.

Estratigrafia do Caloviano do Algarve oriental

The comparative study of the Callovian sections in eastern Algarve allowed us to demonstrate that the discontinuity surface at the base of Malm lies always over the Lower-Callovian, as opposite to what happens in western Algarve; the Bathonian-Callovian transition, continuous in western Algarve (Mareta beach) is marked, in eastern Algarve, by a generalised discontinuity of variable vertical extention. It is verified that, in eastern Algarve, the Callovian formations are always or at the nucleus of anticlinal structures, probably linked to halokinetic tectonic activity, or in large radins folds derived from compressive phases.

Essai de biozonation du Domérien portugais

The biozonation of the portuguese Domerian is presented. This biozonation is based essentially on fauna from the following sections: S. Pedro de Muel, Peniche (Stokesi zone and lower part of the Margaritatus zone) and Brenha (Margaritatus and Spinatum zones). The distribution of the main fossil groups enabled an accurate division of the Stokesi zone into three horizons: Occidentale, Monestieri-Nitescens and Lusitanicum. In the Middle Domerian, the extension of the Ragazzonii horizon was reduced. An Elisa horizon was individualized at the top of the Upper Domerian.

Handling shared resources and precedence constraints in open systems

There is an increasing demand for highly dynamic realtime systems where several independently developed applications with different timing requirements can coexist. This paper proposes a protocol to integrate shared resources and precedence constraints among tasks in such systems assuming no precise information on critical sections and computation times is available. The concept of bandwidth inheritance is combined with a capacity sharing and stealing mechanism to efficiently exchange bandwidth among needed tasks, minimising the cost of blocking.

The capacity exchange protocol

This paper proposes a new strategy to integrate shared resources and precedence constraints among real-time tasks, assuming no precise information on critical sections and computation times is available. The concept of bandwidth inheritance is combined with a capacity sharing and stealing mechanism to efficiently exchange bandwidth among tasks to minimise the degree of deviation from the ideal system’s behaviour caused by inter-application blocking. The proposed Capacity Exchange Protocol (CXP) is simpler than other proposed solutions for sharing resources in open real-time systems since it does not attempt to return the inherited capacity in the same exact amount to blocked servers. This loss of optimality is worth the reduced complexity as the protocol’s behaviour nevertheless tends to be fair and outperforms the previous solutions in highly dynamic scenarios as demonstrated by extensive simulations. A formal analysis of CXP is presented and the conditions under which it is possible to guarantee hard real-time tasks are discussed.

Shared resources and precedence constraints with capacity sharing and stealing

This paper proposes a new strategy to integrate shared resources and precedence constraints among real-time tasks, assuming no precise information on critical sections and computation times is available. The concept of bandwidth inheritance is combined with a greedy capacity sharing and stealing policy to efficiently exchange bandwidth among tasks, minimising the degree of deviation from the ideal system's behaviour caused by inter-application blocking. The proposed capacity exchange protocol (CXP) focus on exchanging extra capacities as early, and not necessarily as fairly, as possible. This loss of optimality is worth the reduced complexity as the protocol's behaviour nevertheless tends to be fair in the long run and outperforms other solutions in highly dynamic scenarios, as demonstrated by extensive simulations.

Monitoring chlorophyll-a with remote sensing techniques in the Tagus Estuary

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Gestão e Sistemas Ambientais

Synthesis of the Piacenzian onshore record between the Aveiro and Setubal parallels (Western portuguese margin)

Onshore, the Piacenzianof the Mondego and Lower Tagus Tertiary basins comprises siliciclastic sediments deposited in shallow marine to continental environments. The outcrops of the deposits are relatively widespread in the Aveiro and Seuibal region. A lithostratigraphic synthesis based on the correlation of geological sections, is presented for the two basins. In general, the Piacenzian sediments display a regressive sucession. The Late Tortonian-Zanclean (?) confined drainage pattern changed at the beginning of Piazencian, to fluvial systems draining to the Atlantic, and capturing the drainage of the inner parts of the Hesperic Meseta. The Piacenzian sedimentary sequence post-dates one of the uprising phases during Neogene compression, recorded by a strong regional unconformity. Some local active faulting - as in Lousa, Rio Maior and Senibal- Pinhal Novo - allowed the local thickening of the sedimentary record. Later compressive tectonism continues to generate reverse faulting and diapiric reactivation, affecting those sediments. Currently, the Piacenzian deposits culminates the marginal piedmonts, widely eroded by the Quaternary fluvial dissection.

A survey of technologies and applications for climbing robots locomotion and adhesion

The interest in the development of climbing robots has grown rapidly in the last years. Climbing robots are useful devices that can be adopted in a variety of applications, such as maintenance and inspection in the process and construction industries. These systems are mainly adopted in places where direct access by a human operator is very expensive, because of the need for scaffolding, or very dangerous, due to the presence of an hostile environment. The main motivations are to increase the operation efficiency, by eliminating the costly assembly of scaffolding, or to protect human health and safety in hazardous tasks. Several climbing robots have already been developed, and other are under development, for applications ranging from cleaning to inspection of difficult to reach constructions. A wall climbing robot should not only be light, but also have large payload, so that it may reduce excessive adhesion forces and carry instrumentations during navigation. These machines should be capable of travelling over different types of surfaces, with different inclinations, such as floors, walls, or ceilings, and to walk between such surfaces (Elliot et al. (2006); Sattar et al. (2002)). Furthermore, they should be able of adapting and reconfiguring for various environment conditions and to be self-contained. Up to now, considerable research was devoted to these machines and various types of experimental models were already proposed (according to Chen et al. (2006), over 200 prototypes aimed at such applications had been developed in the world by the year 2006). However, we have to notice that the application of climbing robots is still limited. Apart from a couple successful industrialized products, most are only prototypes and few of them can be found in common use due to unsatisfactory performance in on-site tests (regarding aspects such as their speed, cost and reliability). Chen et al. (2006) present the main design problems affecting the system performance of climbing robots and also suggest solutions to these problems. The major two issues in the design of wall climbing robots are their locomotion and adhesion methods. With respect to the locomotion type, four types are often considered: the crawler, the wheeled, the legged and the propulsion robots. Although the crawler type is able to move relatively faster, it is not adequate to be applied in rough environments. On the other hand, the legged type easily copes with obstacles found in the environment, whereas generally its speed is lower and requires complex control systems. Regarding the adhesion to the surface, the robots should be able to produce a secure gripping force using a light-weight mechanism. The adhesion method is generally classified into four groups: suction force, magnetic, gripping to the surface and thrust force type. Nevertheless, recently new methods for assuring the adhesion, based in biological findings, were proposed. The vacuum type principle is light and easy to control though it presents the problem of supplying compressed air. An alternative, with costs in terms of weight, is the adoption of a vacuum pump. The magnetic type principle implies heavy actuators and is used only for ferromagnetic surfaces. The thrust force type robots make use of the forces developed by thrusters to adhere to the surfaces, but are used in very restricted and specific applications. Bearing these facts in mind, this chapter presents a survey of different applications and technologies adopted for the implementation of climbing robots locomotion and adhesion to surfaces, focusing on the new technologies that are recently being developed to fulfill these objectives. The chapter is organized as follows. Section two presents several applications of climbing robots. Sections three and four present the main locomotion principles, and the main "conventional" technologies for adhering to surfaces, respectively. Section five describes recent biological inspired technologies for robot adhesion to surfaces. Section six introduces several new architectures for climbing robots. Finally, section seven outlines the main conclusions.