Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

Solid-state reference and ion-selective electrodes : towards portable potentiometric sensing

Potentiometric sensors are very attractive tools for chemical analysis because of their simplicity, low power consumption and low cost. They are extensively used in clinical diagnostics and in environmental monitoring. Modern applications of both fields require improvements in the conventional construction and in the performance of the potentiometric sensors, as the trends are towards portable, on-site diagnostics and autonomous sensing in remote locations. The aim of this PhD work was to improve some of the sensor properties that currently hamper the implementation of the potentiometric sensors in modern applications. The first part of the work was concentrated on the development of a solid-state reference electrode (RE) compatible with already existing solid-contact ion-selective electrodes (ISE), both of which are needed for all-solid-state potentiometric sensing systems. A poly(vinyl chloride) membrane doped with a moderately lipophilic salt, tetrabutylammonium-tetrabutylborate (TBA-TBB), was found to show a satisfactory stability of potential in sample solutions with different concentrations. Its response time was nevertheless slow, as it required several minutes to reach the equilibrium. The TBA-TBB membrane RE worked well together with solid-state ISEs in several different situations and on different substrates enabling a miniature design. Solid contacts (SC) that mediate the ion-to-electron transduction are crucial components of well-functioning potentiometric sensors. This transduction process converting the ionic conduction of an ion-selective membrane to the electronic conduction in the circuit was studied with the help of electrochemical impedance spectroscopy (EIS). The solid contacts studied were (i) the conducting polymer (CP) poly(3,4-ethylienedioxythiophene) (PEDOT) and (ii) a carbon cloth having a high surface area. The PEDOT films were doped with a large immobile anion poly(styrene sulfonate) (PSS-) or with a small mobile anion Cl-. As could be expected, the studied PEDOT solid-contact mediated the ion-toelectron transduction more efficiently than the bare glassy carbon substrate, onto which they were electropolymerized, while the impedance of the PEDOT films depended on the mobility of the doping ion and on the ions in the electrolyte. The carbon cloth was found to be an even more effective ion-to-electron transducer than the PEDOT films and it also proved to work as a combined electrical conductor and solid contact when covered with an ion-selective membrane or with a TBA-TBB-based reference membrane. The last part of the work was focused on improving the reproducibility and the potential stability of the SC-ISEs, a problem that culminates to the stability of the standard potential E°. It was proven that the E° of a SC-ISE with a conducting polymer as a solid contact could be adjusted by reducing or oxidizing the CP solid contact by applying current pulses or a potential to it, as the redox state of the CP solid-contact influences the overall potential of the ISE. The slope and thus the analytical performance of the SC-ISEs were retained despite the adjustment of the E°. The shortcircuiting of the SC-ISE with a conventional large-capacitance RE was found to be a feasible instrument-free method to control the E°. With this method, the driving force for the oxidation/reduction of the CP was the potential difference between the RE and the SC-ISE, and the position of the adjusted potential could be controlled by choosing a suitable concentration for the short-circuiting electrolyte. The piece-to-piece reproducibility of the adjusted potential was promising, and the day-today reproducibility for a specific sensor was excellent. The instrumentfree approach to control the E° is very attractive considering practical applications.

An examination of factors influencing ERP key-user satisfaction: A qualitative case study

Several companies are trying to improve their operation efficiency by implementing an enterprise resource planning (ERP) system that makes it possible to control the resources of the company in real time. However, the success of the implementation project is not a foregone conclusion; a significant part of these projects end in a failure, one way or another. Therefore it is important to investigate ERP system implementation more closely in order to increase understanding about factors influencing ERP system success and to improve the probability of a successful ERP implementation project. Consequently, this study was initiated because a manufacturing case company wanted to review the success of their ERP implementation project. To be exact, the case company hoped to gain both information about the success of the project and insight for future implementation improvement. This study investigated ERP success specifically by examining factors that influence ERP key-user satisfaction. User satisfaction is one of the most commonly applied indicators of information system success. The research data was mainly collected by conducting theme interviews. The subjects of the interviews were six key-users of the newly implemented ERP system. The interviewees were closely involved in the implementation project. Furthermore, they act as representative users that utilize the new system in everyday business processes. The collected data was analyzed by thematizing. Both data collection and analysis were guided by a theoretical frame of reference. This frame was based on previous research on the subject. The results of the study aligned with the theoretical framework to large extent. The four principal factors influencing key-user satisfaction were change management, contractor service, key-user’s system knowledge and characteristics of the ERP product itself. One of the most significant contributions of the research is that it confirmed the existence of a connection between change management and ERP key-user satisfaction. Furthermore, it discovered two new sub-factors influencing contractor service related key-user satisfaction. In addition, the research findings indicated that in order to improve the current level of key-user satisfaction, the case company should pay special attention to system functionality improvement and enhancement of the key-users’ knowledge. During similar implementation projects in the future, it would be important to assure the success of change management and contractor service related processes.

Cardiovascular health from childhood to adulthood – with special reference to early vascular changes. The Cardiovascular Risk in Young Finns Study

Background: Recent recommendations aim to improve cardiovascular health (CVH) by encouraging the general population to meet positive and modifiable ideal CVH metrics: not smoking, being physically active, and maintaining normal weight, blood pressure, blood glucose and total cholesterol levels and a healthy diet. Aims: The aim of the present study was to report the prevalence of ideal CVH in children and young adults and study the associations of CVH metrics with markers of subclinical atherosclerosis. Participants and methods: The present thesis is part of the Cardiovascular Risk in Young Finns Study (Young Finns Study). Data on associations of CVH metrics and subclinical atherosclerosis were available from 1,898 Young Finns Study participants. In addition, joint analyses were performed combining data from the International Childhood Cardiovascular Cohort (i3C) Consortium member studies from Australia and the USA. Results: None of the participants met all 7 CVH metrics and thus had ideal CVH in childhood and only 1% had ideal CVH as young adults. The number of CVH metrics present in childhood and adulthood predicted lower carotid artery intima-media thickness, improved carotid artery distensibility and lower risk of coronary artery calcification. Those who improved their CVH status from childhood to adulthood had a comparable risk of subclinical atherosclerosis to participants who had always had a high CVH status. Conclusions: Ideal CVH proved to be rare among children and young adults. A higher number of ideal CVH metrics and improvement of CVH status between childhood and adulthood predicted a lower risk of subclinical atherosclerosis.

Sähkökoneessa esiintyvien voimien yksityiskohtainen mittausjärjestelmä

Hissiteollisuudessa nostokoneistoina käytettyjen sähkömoottoreiden laatuvaatimukset ovat tiuken-tuneet viime vuosina. Erityisesti koneistojen tuottama ääni ja mekaaninen värähtely ovat olleet jat-kuvasti tiukentuneen tarkastelun alaisena. Hissikoriin ja hissiä ympäröiviin rakenteisiin välittyvästä värähtelystä johtuva ääni on yksi hissin laatuvaikutelmaan merkittävimmin vaikuttavia tekijöitä. Nostokoneisto on yksi tärkeimmistä äänen ja värähtelyn lähteistä hissijärjestelmässä. Koneiston suunnittelulla edellä mainittuja tekijöitä voidaan minimoida. Sähkökoneiden suunnittelussa finiit-tielementtimenetelmien (FEM) käyttö on vakiintunut haastavimmissa sovelluksissa. Kone Oyj:llä nostokoneistoina käytetään aksiaalivuokestomagneettitahtikoneita (AFPMSM), joiden FEM simu-lointiin käytetään yleisesti kolmea eri tapaa. Kukin näistä vaihtoehdoista pitää sisällään omat hyö-tynsä, että haittansa. Suunnittelun kannalta tärkeää on oikean menetelmän valinta ai-ka/informatiivisuus suhteen maksimoimiseksi. Erittäin tärkeää on myös saatujen tulosten oikeelli-suus. Tämän diplomityön tavoite on kehittää järjestelmä, jonka avulla AFPMS-koneen voimia voidaan mitata yksityiskohtaisella tasolla. Järjestelmän avulla voidaan tarkastella käytössä olevien FE-menetelmien tulosten oikeellisuutta sekä äänen että värähtelyn syntymekanismeja. Järjestelmän tarkoitus on myös syventää Kone Oyj tietotaitoa AFPMS-koneiden toiminnasta. Tässä työssä esitellään AFPMS-koneen epäideaalisuuksia, jotka voivat vaikuttaa mittajärjestelmän suunnitteluun. Myös koneen epäideaalisuuksiin lukeutuvaa ääntä on tarkasteltu tässä työssä. Jotta työn tavoitteiden mukaista FE-menetelmien vertailua ja tulosten oikeellisuuden tarkastelua voitai-siin tehdä, myös yleisimpiä AFPMS-koneen FE-menetelmiä tarkastellaan. Työn tuloksena on mittajärjestelmän suunnitelma, jonka avulla voidaan toteuttaa kuuden vapausas-teen voimamittaus jokaiselle koneistomagneetille alle 1N resoluutiolla. Suunnitellun järjestelmän toimivuutta on tarkasteltu FE-menetelmiä käyttäen ja järjestelmässä käytettävän voima-anturin ky-vykkyyttä on todennettu referenssimittauksin. Suunniteltu mittajärjestelmä mahdollistaa sähkömoottorin useiden eri epäideaalisuuksien tarkaste-lun yksityiskohtaisella tasolla. Mittausajatuksen soveltaminen myös muiden koneiden tutkimiseen tarjoaa mahdollisuuksia jatkotutkimuksille.

Reference value of brachial-ankle pulse wave velocity for the eastern Chinese population and potential influencing factors

The present study was conducted to obtain reference values for brachial-ankle pulse wave velocity (baPWV) and to evaluate influencing factors of baPWV according to gender. Using automatic devices, baPWV was measured simultaneously in 2095 subjects. A total of 647 healthy subjects, none of whom presented atherosclerotic risk factors, were analyzed in the present study. Two different statistical methods were used to obtain reference values for baPWV according to subject gender and age. The association between baPWV value and gender, as well as other features, were analyzed. For male subjects, multiple stepwise analysis showed that age, systolic blood pressure (SBP), heart rate (HR), and plasma levels of triglycerides (TG) were independent predictors of baPWV. For female subjects, age, SBP, HR, and plasma levels of uric acid (UA) were independent predictors of baPWV. In male subjects, the upper limits of baPWV values were 1497.43/1425.00, 1518.67/1513.25, 1715.97/1726.50, 1925.20/1971.90, and 2310.18/2115.00 cm/s, obtained using two different statistical methods for the age ranges of 30-39, 40-49, 50-59, 60-69, and 70 and older, respectively. For females, the upper limits of baPWV values were 1426.70/1411.13, 1559.15/1498.95, 1733.50/1739.00, 1958.63/1973.78, and 2720.80/2577.00 cm/s for the age ranges of 30-39, 40-49, 50-59, 60-69, and 70 and older, respectively. Aging is the most important influencing factor for baPWV value and its effect is more prominent in females. The reference values of baPWV according to age and gender may be useful for the clinical diagnosis and preventive therapy of cardiovascular diseases.

Antiretroviral therapy-associated dyslipidemia in patients from a reference center in Brazil

The aim of this study was to determine the impact of antiretroviral therapy on the lipid profile of human immunodeficiency virus (HIV) patients before and after the initiation of highly active antiretroviral therapy (HAART). This was a cross-sectional analysis of patients receiving HAART at a reference center in Belo Horizonte, Brazil, on the basis of medical records from 2002 to 2006. Patients were included if they had at least one lipid test or a clinical or laboratory diagnosis of dyslipidemia/lipodystrophy. Among the 692 patients, 620 met the eligibility criteria. The majority were males (66.5%), middle age (average 39 years), had a low educational level (60.4%), and low income (51.0%). HAART duration ranged from 11 days to 4.6 years, with a mean of 28.6 months (SD = ± 470.19 days). The prevalence of dyslipidemia/lipodystrophy nearly tripled (11.3% pre- and 32.4% post-HAART). Dyslipidemia was associated with older age (P = 0.007), nucleoside reverse transcriptase inhibitor (NRTI) + protease inhibitor (PI) regimens (P = 0.04), NRTI + non-NRTI (NNRTI) regimens (P = 0.026), the use of stavudine (d4T) in any regimen (P = 0.002) or in NRTI-based regimens (P = 0.006), and longer exposure to HAART (P < 0.000). In addition, there was no correlation between dyslipidemia and gender (P = 0.084). Only 2.0% of the patients received treatment for dyslipidemia during the trial. These results show a need for continuous monitoring of patients under antiretroviral therapy, particularly those using NRTI-based regimens, especially when combined with d4T and PIs. Secondly, interventions should be developed to correct metabolic changes.

Role of a GenoType MTBDRplus line probe assay in early detection of multidrug-resistant tuberculosis at a Brazilian reference center

Resistance to Mycobacterium tuberculosis is a reality worldwide, and its diagnosis continues to be difficult and time consuming. To face this challenge, the World Health Organization has recommended the use of rapid molecular tests. We evaluated the routine use (once a week) of a line probe assay (Genotype MTBDRplus) for early diagnosis of resistance and for assessment of the main related risk factors over 2 years. A total of 170 samples were tested: 15 (8.8%) were resistant, and multidrug resistance was detected in 10 (5.9%). The sensitivity profile took 3 weeks (2 weeks for culture and 1 week for rapid testing). Previous treatment for tuberculosis and the persistence of positive acid-fast smears after 4 months of supervised treatment were the major risk factors observed. The use of molecular tests enabled early diagnosis of drug-resistant bacilli and led to appropriate treatment of the disease. This information has the potential to interrupt the transmission chain of resistant M. tuberculosis.

Improving oral healthcare in Scotland with special reference to sustainability and caries prevention

Brett Duane Improving oral healthcare in Scotland with special reference to sustainability and caries prevention University of Turku, Faculty of Medicine, Institute of Dentistry, Community Dentistry, Finnish Doctoral Program in Oral Sciences (FINDOS-Turku), Turku, Finland Annales Universitatis Turkuensis, Sarja- Ser. D, Medica-Odontologica. Painosalama Oy, Turku, Finland, 2015. Dentistry must provide sustainable, evidence-based, and prevention-focused care. In Scotland oral health prevention is delivered through the Childsmile programme, with an increasing use of high concentration fluoride toothpaste (HCFT). Compared with other countries there is little knowledge of xylitol prevention. The UK government has set strict carbon emission limits with which all national health services (NHS) must comply. The purpose of these studies was firstly to describe the Scottish national oral health prevention programme Childsmile (CS), to determine if the additional maternal use of xylitol (CS+X) was more effective at affecting the early colonisation of mutans streptococci (MS) than this programme alone; secondly to analyse trends in the prescribing and management of HCFT by dentists; and thirdly to analyse data from a dental service in order to improve its sustainability. In all, 182 mother/child pairs were selected on the basis of high maternal MS levels. Motherswere randomly allocated to a CS or CS+X group, with both groups receiving Childsmile. Theintervention group consumed xylitol three times a day, from when the child was 3 months until 24 months. Children were examined at age two to assess MS levels. In order to understand patterns of HCFT prescribing, a retrospective secondary data analysis of routine prescribing data for the years 2006-2012 was performed. To understand the sustainability of dental services, carbon accounting combined a top-down approach and a process analysis approach, followed by the use of Pollard’s decision model (used in other healthcare areas) to analyse and support sustainable service reconfiguration. Of the CS children, 17% were colonised with MS, compared with 5% of the CS+X group. This difference was not statistically significant (P=0.1744). The cost of HCFT prescribing increased fourteen-fold over five years, with 4% of dentists prescribing 70% of the total product. Travel (45%), procurement (36%) and building energy (18%) all contributed to the 1800 tonnes of carbon emissions produced by the service, around 4% of total NHS emissions. Using the analytical model, clinic utilisation rates improved by 56% and patient travel halved significantly reducing carbon emissions. It can be concluded that the Childsmile programme was effective in reducing the risk for MS transmission. HCFT is increasing in Scotland and needs to be managed. Dentistry has similar carbon emissions proportionally as the overall NHS, and the use of an analytic tool can be useful in helping identify these emissions. Key words: Sustainability, carbon emissions, xylitol, mutans streptococci, fluoride toothpaste, caries prevention.

Sekaelementit absoluuttisten solmukoordinaattien menetelmässä

Tässä lisensiaatintyössä käsitellään sekaelementtien sovellusmahdollisuuksia absoluuttisten solmukoordinaattien menetelmässä. Absoluuttisten solmukoordinaattien menetelmä on uudentyyppinen lähestymistapa elementtimenetelmän elementtien koordinaattien määrittämiseksi ja sen yhtenä tavoitteena on tehostaa suuria siirtymiä tai kiertymiä sisältävien elementtien laskentatehokkuutta. Tässä työssä absoluuttisten solmukoordinaattien menetelmä esitellään pääpiirteittäin sekä annetaan esimerkkejä muutamista tyypillisimmistä elementeistä lausuttuna edellä mainittujen koordinaattien perusteella. Sekaelementeiksi kutsutaan elementtityyppejä, missä tuntemattomien muuttujien joukkoja on aina enemmän kuin yksi. Sekaelementit erottavat redusoitumattomista elementeistä siirtymäkentän sisältyminen muuttujaryhmään ja hybridielementeistä muuttujien identtiset ulottuvuudet. Sekaelementtejä käytetään esimerkiksi kokoonpuristumattomien materiaalien rakenneanalyyseissä, alentamaan elementiltä vaadittavia jatkuvuusehtoja tai mallintamaan ilmiöitä, missä fysikaaliset ominaisuudet ovat jostain syystä voimakkaasti toisistaan riippuvaisia. Tämän lisensiaatintyön kirjoittamiseksi on tehty tutkimusta sekaelementtien mahdollisuuksista toimia absoluuttisten solmukoordinaattien menetelmässä. Tutkimuksen tuloksena on saatu aikaan kaksi tässä työssä esiteltävää, varsin rajatun toimintakyvyn omaavaa sekaelementtityyppiä, joiden siirtymäkentät on määritelty globaalien koordinaattien suhteen sisältäen myös orientaatiotermit. Tutkimusaihe vaatii kuitenkin vielä paljon lisätyötä, ennen kuin sekaelementtityyppejä voidaan kauttaaltaan soveltaa absoluuttisten solmukoordinaattien menetelmällä toteutetuissa rakenneanalyyseissä.

Safety and outcome of coronary interventions with special reference to anticoagulation and stent type

University of Turku, Faculty of Medicine, Department of Cardiology and Cardiovascular Medicine, Doctoral Programme of Clinical Investigation, Heart Center, Turku University Hospital, Turku, Finland Division of Internal Medicine, Department of Cardiology, Seinäjoki Central Hospital, Seinäjoki, Finland Heart Center, Satakunta Central Hospital, Pori, Finland Annales Universitatis Turkuensis Painosalama Oy, Turku, Finland 2015 Antithrombotic therapy during and after coronary procedures always entails the challenging establishment of a balance between bleeding and thrombotic complications. It has been generally recommended to patients on long-term warfarin therapy to discontinue warfarin a few days prior to elective coronary angiography or intervention to prevent bleeding complications. Bridging therapy with heparin is recommended for patients at an increased risk of thromboembolism who require the interruption of anticoagulation for elective surgery or an invasive procedure. In study I, consecutive patients on warfarin therapy referred for diagnostic coronary angiography were compared to control patients with a similar disease presentation without warfarin. The strategy of performing coronary angiography during uninterrupted therapeutic warfarin anticoagulation appeared to be a relatively safe alternative to bridging therapy, if the international normalized ratio level was not on a supratherapeutic level. In-stent restenosis remains an important reason for failure of long-term success after a percutaneous coronary intervention (PCI). Drug-eluting stents (DES) reduce the problem of restenosis inherent to bare metal stents (BMS). However, a longer delay in arterial healing may extend the risk of stent thrombosis (ST) far beyond 30 days after the DES implantation. Early discontinuation of antiplatelet therapy has been the most important predisposing factor for ST. In study II, patients on long-term oral anticoagulant (OAC) underwent DES or BMS stenting with a median of 3.5 years’follow-up. The selective use of DESs with a short triple therapy seemed to be safe in OAC patients, since late STs were rare even without long clopidogrel treatment. Major bleeding and cardiac events were common in this patient group irrespective of stent type. In order to help to predict the bleeding risk in patients on OAC, several different bleeding risk scorings have been developed. Risk scoring systems have also been used also in the setting of patients undergoing a PCI. In study III, the predictive value of an outpatient bleeding risk index (OBRI) to identify patients at high risk of bleeding was analysed. The bleeding risk seemed not to modify periprocedural or long-term treatment choices in patients on OAC after a percutaneous coronary intervention. Patients with a high OBRI often had major bleeding episodes, and the OBRI may be suitable for risk evaluation in this patient group. Optical coherence tomography (OCT) is a novel technology for imaging intravascular coronary arteries. OCT is a light-based imaging modality that enables a 12–18 µm tissue axial resolution to visualize plaques in the vessel, possible dissections and thrombi as well as, stent strut appositions and coverage, and to measure the vessel lumen and lesions. In study IV, 30 days after titanium-nitride-oxide (TITANOX)-coated stent implantation, the binary stent strut coverage was satisfactory and the prevalence of malapposed struts was low as evaluated by OCT. Long-term clinical events in patients treated with (TITANOX)-coated bio-active stents (BAS) and paclitaxel-eluting stents (PES) in routine clinical practice were examined in study V. At the 3-year follow-up, BAS resulted in better long-term outcome when compared with PES with an infrequent need for target vessel revascularization. Keywords: anticoagulation, restenosis, thrombosis, bleeding, optical coherence tomography, titanium