Origin of double dinitrogen release feature during fast switching between lean and rich cycles for NOx storage reduction catalysts

The performance of NOx storage and reduction over 1.5 wt% Pt/20 wt% KNO3/K2Ti8O17 and 1.5 wt% Pt/K2Ti8O17 catalysts has been investigated using combined fast transient kinetic switching and isotopically labelled (NO)-N-15 at 350 degrees C. The evolution of product N-2 has revealed two significant peaks during 60 s lean/1.3 s rich switches. It also found that the presence of CO2 in the feed affects the release of N-2 in the second peak. Regardless of the presence/absence of water in the feed, only one peak of N-2 was observed in the absence of CO2. Gas-phase NH3 was not observed in any of the experiments. However, in the presence of CO2 the results obtained from in situ DRIFTS-MS analysis showed that isocyanate species are formed and stored during the rich cycles, probably from the reaction between NOx and CO, in which CO was formed via the reverse water-gas shift reaction. 

Self-cleaning perovskite type catalysts for the dry reforming of methane

Gas-to-liquid processes are generally used to convert natural gas or other gaseous hydrocarbons into liquid fuels via an intermediate syngas stream. This includes the production of liquid fuels from biomass-derived sources such as biogas. For example, the dry reforming of methane is done by reacting CH4 and CO2, the two main components of natural biogas, into more valuable products, i.e., CO and H2. Nickel containing perovskite type catalysts can promote this reaction, yielding good conversions and selectivities; however, they are prone to coke laydown under certain operating conditions. We investigated the addition of high oxygen mobility dopants such as CeO2, ZrO2, or YSZ to reduce carbon laydown, particularly using reaction conditions that normally result in rapid coking. While doping with YSZ, YDC, GDC, and SDC did not result in any improvement, we show that a Ni perovskite catalyst (Na0.5La0.5Ni0.3Al0.7O2.5) doped with 80.9 ZrO2 15.2 CeO2 gave the lowest amount of carbon formation at 800 °C and activity was maintained over the operating time.

Correlation of Static Ageing Effects on Automotive Catalysts

This study identifies and analyzes the effect that aging time and temperature have on the CO light-off activity of three-way catalyst samples, aged in a static air (oxidizing) atmosphere. The bench aging time (BAT) equation proposed by the Environmental Protection Agency (EPA), which describes aging as dependent upon time at temperature, was used to calculate a range of oven aging times and temperatures based on a RAT-A engine bench aging cycle.

CO light-off tests carried out on cores aged between 800 and 900 °C have shown that it is the aging temperature that has the greatest effect on catalyst deterioration for static aging testing, with aging time having little effect. These results were in contradiction to the BAT equation, an industry norm for the aging of catalysts. This demonstrates that static aging, whilst showing how temperature affects aging, gives little or no time effects. The results have shown that static aging is not representative of actual aging on a vehicle.

Progressive aging conducted at a temperature of 1000 °C was shown to cause a decrease in catalyst activity as the aging time increased. However, even in these extreme conditions, static aging gave a slower rate of aging with time when compared to engine aging as defined by the BAT equation. Overall, static aging in air has been shown to produce a greater increase in aging due to temperature than predicted by the BAT equation, but less aging due to aging time.

Advanced Ceramic Substrate with Ordered and Designed Micro-Structure for Applications in Automotive Catalysts

This study describes an innovative monolith structure designed for applications in automotive catalysis using an advanced manufacturing approach developed at Imperial College London. The production process combines extrusion with phase inversion of a ceramic-polymer-solvent mixture in order to design highly ordered substrate micro-structures that offer improvements in performance, including reduced PGM loading, reduced catalyst ageing and reduced backpressure.

This study compares the performance of the novel substrate for CO oxidation against commercially available 400 cpsi and 900 cpsi catalysts using gas concentrations and a flow rate equivalent to those experienced by a full catalyst brick when attached to a vehicle. Due to the novel micro-structure, no washcoat was required for the initial testing and 13 g/ft3 of Pd was deposited directly throughout the substrate structure in the absence of a washcoat.

Initial results for CO oxidation indicate that the advanced micro-structure leads to enhanced conversion efficiency. Despite an 79% reduction in metal loading and the absence of a washcoat, the novel substrate sample performs well, with a light-off temperature (LOT) only 15 °C higher than the commercial 400 cpsi sample.

To test the effects of catalyst ageing on light-off temperature, each sample was aged statically at a temperature of 1000 °C, based on the Bench Ageing Time (BAT) equation. The novel substrate performed impressively when compared to the commercial samples, with a variation in light-off temperature of only 3% after 80 equivalent hours of ageing, compared to 12% and 25% for the 400 cpsi and 900 cpsi monoliths, respectively.

Synthesis of , of α,β-unsaturated aldehydes and nitriles via cross-metathesis reactions using Grubbs’ catalysts

A series of alpha,beta-unsaturated aldehydes and nitriles of significant interest in the fragrance industry have been prepared using Grubbs' catalysts in cross-metathesis reactions of electron-deficient olefins (i.e., acrolein, crotonaldehyde, methacrolein, and acrylonitrile) with various 1-alkenes, including 1-decene, 1-octene, 1-hexene and 2-allyloxy-6-methylheptane. The latter is of particular interest, as it has not previously being used as a substrate in cross-metathesis reactions and allows access to valuable intermediates for the synthesis of new fragrances. Most reactions gave good selectivity of the desired CM product (>= 90%). Detailed optimisation and mechanistic studies have been performed on the cross-metathesis of acrolein with 1-decene. Recycling of the catalyst has been attempted using ionic liquids. 

A Highly Efficient Palladium(II)/Polyoxometalate Catalyst System for Aerobic Oxidation of Alcohols

A simple catalyst system composed of Pd(OAc)2, phosphomolybdic acid and tetrabutylammonium acetate oxidises a range of alcohols efficiently, with turnover numbers (TONs) of up to 10 000.

Mechanochemical preparation of Ag catalysts for the n-octane-SCR de-NOx reaction: Structural and reactivity effects

Mechanochemical preparation of Ag/Al2O3 catalysts used for the selective catalytic reduction of NOx using hydrocarbons has been shown to substantially increase the activity of the catalyst in comparison with Ag/Al2O3 prepared by wet impregnation. The effect of using different ball-milling experimental parameters on both the structure of the material as well as the catalyst activity has been investigated and the optimum conditions established. A phase transition from γ- to α-alumina was observed milling at high speeds which was found to result in lower catalyst activities. At lower milling speeds both fracturing and agglomeration of the alumina support can be observed depending on the grinding time. However, due to ball-milling, a general enhancement in the NOx reduction activity was observed for all catalysts compared with the conventionally prepared catalysts irrespective of the reductant used. Transient DRIFTS-MS experiments were performed to investigate the effect of H2 in the absence and presence of water on the SCR reaction over catalysts prepared by both ball milling and wet impregnation. In-situ DRIFTS-MS analysis revealed significant differences in both gas phase and surface species. Most notably, isocyanate species were formed significantly more quickly and at higher surface concentration in the case of the mechanochemically prepared catalyst.

Palladium-Catalyzed Oxidative Synthesis of Highly Functionalized Ortholactones

A palladium-catalyzed oxidative reaction is reported which converts dihydropyrans to their corresponding ortholactone. The products are formed in good to excellent yields with a very high level of chemoselectivity and functional group tolerance. Mechanistic studies confirm that the reaction proceeds by a Wacker-type mechanism.

Palladium catalysed tandem cyclisation - Anion capture processes .2. Cyclisation onto alkynes or allenes with hydride capture.

A wide range of palladium catalysed regio- and stereo-specific 5-, 6- and 7-exo-dig mono-, bis- and tris-cyclisation processes of aryl and vinyl halides and allylic acetates are described. The mono- and bis-cyclisation processes terminate in hydride capture from piperidine-formic acid or sodium formate. Addition of TI2CO3 results in alkyne-allene isomerisation and leads, after cyclisation, to 1,3-dienes which give Diels-Alder adducts in good yield. Copyright (C) 1996 Elsevier Science Ltd

PALLADIUM CATALYZED TANDEM CYCLIZATION-ANION CAPTURE PROCESSES .1. BACKGROUND AND HYDRIDE ION CAPTURE BY ALKYL-PALLADIUM AND PI-ALLYL-PALLADIUM SPECIES

A new, wide ranging, synthetically powerful, catalytic tandem cyclisation-anion capture process is proposed which depends on the rate of cyclisation of an organopalladium specifies (RPdX) onto a proximate alkene or diene being significantly faster than anion exchange and reductive elimination in the sequence RPdX --> RPdY --> RY + Pd(0). The catalytic cyclisation - anion capture sequence is illustrated for hydride capture by a wide variety of substrates giving rise to fused- and spiro-, carbo- and hetero-cyclic systems, regio- and stereo-specifically.