Influence of the heat treatment on the nucleation of silver nanoparticles in Tm(3+) doped PbO-GeO(2) glasses

Nucleation of silver nanoparticles (NPs) in Tm(3+) doped PbO-GeO(2) (PGO) glass is reported. The influence of the heat treatment on the nucleation of silver NPs is studied by means of transmission electron microscopy and optical spectroscopy. Two heat treatment procedures were applied in order to compare their performance. Observation of infrared-to-visible frequency upconversion (UC) luminescence of Tm(3+) ions is reported and correlated with the heat-treatment procedure. Enhancement of the UC emission for samples heat treated during various time intervals is attributed to the increased local field in the vicinity of the NPs. Quenching of the UC signal was also observed and correlated with the growth of NPs amount and size.

Study of an alternative phosphate sealer for replacement of hexavalent chromium

This study evaluates the possibility of replacing the hexavalent chromium passivation treatment used as a sealer after phosphating of carbon steel (SAE 1010) by a treatment with niobium ammonium oxalate (Ox). Samples of carbon steel (SAE 1010) after being phosphated in a zinc phosphate bath (PZn + Ni) were immersed in solution of niobium ammonium oxalate (250 mg L(-1) of Nb) either at pH 3.0 or pH 8.0. A passivation treatment with a solution with CrO(3) (200 mg L(-1) of Cr(6+)) was also used for reference. The corrosion resistance of the phosphated samples after passivation treatments was analyzed in a NaCl 0.5 mol L(-1) solution using electrochemical impedance spectroscopy (EIS) and anodic polarization curves. Salt spray tests were also performed to evaluate their corrosion resistance. The results showed that the highest corrosion resistance was obtained by passivation in a solution with (250 mg L(-1) of Nb) at pH 8.0. (C) 2010 Elsevier B.V. All rights reserved.

Influence of gold nanoparticles on optically stimulated effects in TeO(2)-ZnO and GeO(2)-PbO amorphous thin films

We have found photoinduced second harmonic generation at wavelength 1064 nm during bicolor Nd:YAG laser coherent treatment of TeO(2)-ZnO and GeO(2)-PbO amorphous films. The maximally achieved second order susceptibility was equal to about 1.02 pm/V. Correlation of the induced second order susceptibility with local sample heating and induced birefringence may indicate an occurrence of local phase transitions from amorphous glass-like phase to non-centrosymmetry metastable phases. (C) 2010 Elsevier B.V. All rights reserved.

Electron beam induced second-harmonic generation in Er(3+) doped PbO-GeO(2) glasses containing silver nanoparticles

Electron beam induced second harmonic generation (SHG) is studied in Er(3+) doped PbO-GeO(2) glasses containing silver nanoparticles with concentrations that are controlled by the heat-treatment of the samples. The SHG is observed at T = 4.2 K using a p-polarized laser beam at 1064 nm. Enhancement of the SHG is observed in the samples that are submitted to electron beam incidence. The highest value of the nonlinear susceptibility, 2.08 pm/V, is achieved for the sample heat-treated during 72 h and submitted to an electron beam current of 15 nA. The samples that were not exposed to the electron beam present a susceptibility of a parts per thousand 0.5 pm/V.

PbO-GeO(2) rib waveguides for photonic applications

This work presents for the first time to our knowledge the fabrication and characterization of rib waveguides produced with PbO-GeO(2) (PGO) thin films. The target was manufactured using pure oxides ( 60 PbO-40 GeO(2), in wt%) and amorphous thin films were produced with the RF sputtering technique. PGO thin films present small absorption in the visible and in the near infrared and refractive index of similar to 2.0. The definition of the rib waveguide structure was made using conventional optical lithography followed by plasma etching, performed in a Reactive Ion Etching (RIE) reactor. Light propagation mode in the waveguide structure was analyzed using integrated optic simulation software. Optical loss measurements were performed to determine the propagation loss at 633 nm, for ribs with height of 70 nm and width of 3-5 mu m; experimental values around 2 dB/cm were found for the propagation loss and confirmed the theoretical calculations. The results obtained demonstrate that PGO thin films are potential candidates for application in integrated optics. Published by Elsevier B.V.

Strain origin drives virulence and persistence of Xylella fastidiosa in alfalfa

Generalist pathogens frequently exist as a complex of genetically differentiated strains, which can differ in virulence and transmissibility. A description of the extent to which strain variability mediates host species competence is needed to understand disease dynamics for systems with both host and pathogen strain diversity. This study tested the hypothesis that strain-specific variation of a generalist vector-borne plant pathogen, Xylella fastidiosa, affects disease severity in alfalfa (Medicago sativa) and competence of this crop as a reservoir host. Alfalfa seedlings were inoculated with one of 23 X. fastidiosa isolates collected from different hosts, eight identified as belonging to an almond strain, and the remainder from a grape strain. Pathogen population, symptom severity and infection incidence were compared over five successive harvests. Infected plant size, measured mainly by plant height, internode length and above ground biomass, was reduced up to 50% compared to buffer-inoculated controls, and more severe symptoms were observed at later harvests and for higher pathogen populations. Grape isolates had higher bacterial populations within alfalfa than almond isolates. In addition, infection with grape isolates resulted in more severe alfalfa stunting than that caused by almond isolates. Moreover, there was a strong positive relationship between isolate multiplication rate and both symptom severity and infection persistence (i.e. maintenance of chronic infection within host). Isolates with low initial populations had low incidence at the final harvest, with one isolate dying out altogether. The results showed that X. fastidiosa-genetic diversity contributed to variation in alfalfa disease severity. The results also suggest that pathogen strain may mediate host competence via differences in bacterial population density and persistence.

Pupal Development of Ceratitis capitata (Diptera: Tephritidae) and Diachasmimorpha longicaudata (Hymenoptera: Braconidae) at Different Moisture Values in Four Soil Types

This study aimed to evaluate adult emergence and duration of the pupal stage of the Mediterranean fruit fly, Ceratitis capitata (Wiedemann), and emergence of the fruit fly parasitoid, Diachasmimorpha longicaudata (Ashmead), under different moisture conditions in four soil types, using soil water matric potential Pupal stage duration in C capitata was influenced differently for males and females In females, only soil type affected pupal stage duration, which was longer in a clay soil In males, pupal stage duration was individually influenced by moisture and soil type, with a reduction in pupal stage duration in a heavy clay soil and in a sandy clay, with longer duration in the clay soil As allude potential decreased, duration of the pupal stage of C capitata males increased, regardless of soil type C capitata emergence was affected by moisture, regardless of soil type, and was higher in drier soils The emergence of D longicaudata adults was individually influenced by soil type and moisture factors, and the number of emerged D longicaudata adults was three times higher in sandy loam and lower in a heavy clay soil Always, the number of emerged adults was higher at higher moisture conditions C capitata and D longicaudata pupal development was affected by moisture and soil type, which may facilitate pest sampling and allow release areas for the parasitoid to be defined under field conditions.

The Effects of Host, Geographic Origin, and Gender on the Thermal Requirements of Diaphorina citri (Hemiptera: Psyllidae)

Diaphorina citri Kuwayama (Hemiptera: Psyllidae) is the vector of the bacteria that causes citrus greening and is considered one of the world`s most important citrus diseases. We examined how host, geographic region, and gender affect the thermal requirements of D. citri. The insects were reared in climatic chambers at constant temperatures of 18, 20, 22, 25, 28, 30, and 32 1 degrees C, 70 +/- 10% RH, and a 14 h photophase. Host plants for D. citri included orange (Citrus sinensis [Rutaceae]) varieties Pera and Natal, the rootstock, Rungpur lime (C. limonia [Rutaceae]) and the natural host, Orange jessamine (Murraya paniculata [Rutaceae]). To study the influence of geographic origin on thermal requirements, we studied D. citri populations from Piracicaba, SP (warmer region) and Itapetininga, SP (cooler region). The duration and survival of the development stages and the duration of the total development (egg-adult) did not differ significantly on the different hosts, but it did vary with temperature. Nymphs of D. citri created on the different hosts have the same thermal requirements. The thermal requirements for this species collected from the two climate regions were identical; males and females also had the same thermal requirements.

Reproductive Activity and Survivorship of Liriomyza sativae (Diptera: Agromyzidae) at Different Temperatures and Relative Humidity Levels

We studied a population of Liriomyza sativae Blanchard (Diptera: Agromyzidae) identified by morphological and molecular techniques from the semiarid region of the Brazilian northeast. The influence of temperature and relative humidity on the survival and reproductive parameters of L. sativae in cowpeas (Vigna unguiculata L. Walp.) (Fabales: Fabaceae) was evaluated. We used temperatures of 18, 20, 22, 25, 28, 30, and 32 +/- 1 degrees C (50 +/- 10% RH) and relative humidity values of 30,50,70, and 90 +/- 10% (25 +/- 1 degrees C) under a 14 L:10 D photoperiod. Adult longevity decreased as temperature and relative humidity increased and was greater, in general, for females. The preoviposition and oviposition periods also decreased as temperature increased, whereas relative humidity only caused reductions in the oviposition period at higher levels. Fecundity was similar in the range from 18 to 30 degrees C but decreased at 32 degrees C with respect to relative humidity; the best performances of L. sativae occurred at lower levels. The pattern of oviposition rate changed with temperature and relative humidity. Regardless of temperature and relative humidity, L, sativae laid between 75 and 92% of its eggs on the adaxial surface of the cowpea leaves. This information will be highly useful to design a leafminer production system aimed at the multiplication of natural enemies, as well as for pest management in the field.

Annual and polyetic progression of citrus canker on trees protected with copper sprays

The effects of copper sprays on annual and polyetic progress of citrus canker, caused by Xanthomonas citri subsp. citri, in the presence of the Asian citrus leafminer (Phyllocnistis citrella), were evaluated in a study conducted in a commercial orchard in northwest Parana state, Brazil, where citrus canker is endemic. Nonlinear monomolecular, logistic and Gompertz models were fitted to monthly disease incidence data (proportion of leaves with symptoms) for each treatment for three seasons. The logistic model provided the best estimate of disease progress for all years and treatments evaluated and logistic parameter estimates were used to describe polyetic disease dynamics. Although citrus canker incidence increased during each of the seasons studied, it decreased over the whole study period, more so in copper-treated trees than in water-sprayed controls. Copper treatment reduced disease incidence compared with controls in every year, especially 2004-2005, when incidence was ca. 10-fold higher in controls than in treated plots (estimated asymptote values 0 center dot 82 and 0 center dot 07, respectively). Copper treatment also reduced estimated initial disease incidence and epidemic growth rates every year.

Copper sprays and windbreaks for control of citrus canker on young orange trees in southern Brazil

The benefit of windbreaks and copper sprays for control of citrus canker caused by Xanthomonas axonopodis pv. citri was investigated in a commercial citrus orchard located in a citrus canker endemic area in southern Brazil. Control of canker was evaluated as incidence and severity of lesions on foliage and by the effect on premature leaf and fruit drop for three production seasons. Effect of the treatments on fruit production was evaluated as incidence of citrus canker on prematurely abscised fruits and harvested fruits. Copper application significantly reduced damage to foliage and fruit, while windbreaks made little contribution to disease control. Copper sprays increased fruit yield for 3 years. This could be attributed to lower incidence of fruit with lesions and fewer fruits abscised due to canker infection. Incidence and severity on the leaves were inversely related to the number of fruits harvested per tree and directly related to the number of fruits abscised per tree. Published by Elsevier Ltd.

Outcrossing rate in sweet passion fruit based on molecular markers

P>Yellow and sweet passion fruit are insect-pollinated species native to the tropics. Fruits are used commercially for human consumption worldwide. The yellow passion fruit is an outcrossing species with self-incompatible flowers. However, the reproductive system of the sweet passion fruit (Passiflora alata) has not been well elucidated. The objective of this work was to characterize aspects of the mating system in the sweet passion fruit using random amplified polymorphic DNA (RAPD) and microsatellite markers, particularly the rate of outcrossing in P. alata progenies. A multilocus outcrossing rate of t(m) = 0.994 was determined from RAPD and t(m) = 0.940 from microsatellites, supporting P. alata as an outcrossing species. The fixation indices of the maternal generation (F(m)) were -0.200 and 0.071 with RAPD and microsatellite loci, respectively, indicating the absence of inbreeding in the maternal generation. The paternity correlation (r(p)) varied from -0.008 with RAPD markers to 0.208 with microsatellite markers, suggesting a low probability of finding full sibs within the progenies. The results demonstrated that all progenies assessed in this study were derived from outcrossing.

Effectiveness of the standard evaluation method for hydraulic nozzles employed in stored grain protection trials

In stored grains, smaller depositions and great variation with respect to theoretical insecticide doses are frequently found. The objective of this work was to study the effectiveness of the standard method (ISO 5682/1-1996) employed to evaluate hydraulic nozzles used in stored corn and wheat grain protection experiments. The transversal volumetric distribution and droplet spectrum of a model TJ-60 8002EVS nozzle were determined in order to calibrate a spraying system for an application rate of 5 L/t and to obtain theoretical concentrations of 10 and 0.5 mg/kg of fenitrothion and esfenvalerate, respectively. After treatment, the corn and wheat grains were processed and deposition was analyzed by gas chromatography. The type of grain did not have any influence on insecticide deposition and was dependent upon insecticide only. The insecticide deposits on the grains only reached 42.1 and 38.2% of the intended theoretical values for fenitrothion and esfenvalerate concentrations, respectively. These results demonstrate the ineffectiveness of the standard evaluation method for hydraulic nozzles employed in stored grain protection experiments.

Biogas production and valorization by means of a two-step biological process

The scope of this research work was to investigate biogas production and purification by a two-step bench-scale biological system, consisting of fed-batch pulse-feeding anaerobic digestion of mixed sludge, followed by methane enrichment of biogas by the use of the cyanobacterium Arthrospira platensis. The composition of biogas was nearly constant, and methane and carbon dioxide percentages ranged between 70.5-76.0% and 13.2-19.5%, respectively. Biogas yield reached a maximum value (about 0.4 m(biogas)(3)/kgCOD(i)) at 50 days-retention time and then gradually decreased with a decrease in the retention time. Biogas CO(2) was then used as a carbon source for A. platensis cultivation either under batch or fed-batch conditions. The mean cell productivity of fed-batch cultivation was about 15% higher than that observed during the last batch phase (0.035 +/- 0.006 g(DM)/L/d), likely due to the occurrence of some shading effect under batch growth conditions. The data of carbon dioxide removal from biogas revealed the existence of a linear relationship between the rates of A. platensis growth and carbon dioxide removal from biogas and allowed calculating carbon utilization efficiency for biomass production of almost 95%. (C) 2009 Elsevier Ltd. All rights reserved.

Preparation and characterization of D, L-PLA loaded 17-beta-Estradiol valerate by emulsion/evaporation methods

PLA microparticles containing 17-beta-estradiol valerate were prepared by an emulsion/evaporation method in order to sustain drug release. This system was characterized concerning particle size, particle morphology and the influence of formulation and processing parameters on drug encapsulation and in vitro drug release. The biodegradation of the microparticles was observed by tissue histological analysis. Scanning electron microscopy and particle size analysis showed that the microparticles were spherical, presenting non-aggregated homogeneous surface and had diameters in the range of 718-880 nm (inert microparticles) and 3-4 mu m (drug loaded microparticles). The encapsulation efficiency was similar to 80%. Hormone released from microparticles was sustained. An in vivo degradation experiment confirmed that microparticles are biodegradable. The preparation method was shown to be suitable, since the morphological characteristics and efficiency yield were satisfactory. Thus, the method of developed microparticles seems to be a promising system for sustained release of 17-beta-estradiol.