Seismic activity triggered by water wells in the Parana Basin, Brazil

Triggered seismicity is commonly associated with deep water reservoirs or injection wells where water is injected at high pressure into the reservoir rock. However, earth tremors related solely to the opening of groundwater wells are extremely rare. Here we present a clear case of seismicity induced by pore-pressure changes following the drilling of water wells that exploit a confined aquifer in the intracratonic Parana Basin of southeastern Brazil. Since 2004, shallow seismic activity, with magnitudes up to 2.9 and intensities V MM, has been observed near deep wells (120-200 m) that were drilled in early 2003 near the town of Bebedouro. The wells were drilled for irrigation purposes, cross a sandstone layer about 60-80 m thick and extract water from a confined aquifer in fractured zones between basalt flow layers. Seismic activity, mainly event swarms, has occurred yearly since 2004, mostly during the rainy season when the wells are not pumped. During the dry season when the wells are pumped almost continuously, the activity is very low. A seismographic network, installed in March 2005, has located more than 2000 microearthquakes. The events are less than 1 km deep (mostly within the 0.5 km thick basalt layer) and cover an area roughly 1.5 km x 5 km across. The seismicity generally starts in a small area and expands to larger distances with an equivalent hydraulic diffusivity ranging from 0.06 to 0.6 m(2)/s. Geophysical and geothermal logging of several wells in the area showed that water from the shallow sandstone aquifer enters the well at the top and usually forms waterfalls. The waterfalls flow down the sides of the wells and feed the confined, fractured aquifer in the basalt layer at the bottom. Two seismic areas are observed: the main area surrounds several wells that are pumped continuously during the dry season, and a second area near another well (about 10 km from the first area) that is not used for irrigation and not pumped regularly. The main area displays cyclic annual activity, but the second area does not. We explain the earthquake swarms as being triggered by pore pressure diffusion in the fractured basalt layer due to additional pressure from the newly connected surface aquifer. This reaches critically prestressed areas up to a few kilometers away from the wells. During periods of continuous pumping, the reduction of pore pressure in the confined aquifer stops the seismic activity. Our study suggests that this kind of activity may be more common than previously thought and implies that many other cases of small tremors associated with the drilling of water wells may have gone unnoticed.

Patterns of water and heat flux across a biome gradient from tropical forest to savanna in Brazil

We investigated the seasonal patterns of water vapor and sensible heat flux along a tropical biome gradient from forest to savanna. We analyzed data from a network of flux towers in Brazil that were operated within the Large-Scale Biosphere-Atmosphere Experiment in Amazonia (LBA). These tower sites included tropical humid and semideciduous forest, transitional forest, floodplain (with physiognomies of cerrado), and cerrado sensu stricto. The mean annual sensible heat flux at all sites ranged from 20 to 38 Wm(-2), and was generally reduced in the wet season and increased in the late dry season, coincident with seasonal variations of net radiation and soil moisture. The sites were easily divisible into two functional groups based on the seasonality of evaporation: tropical forest and savanna. At sites with an annual precipitation above 1900 mm and a dry season length less than 4 months (Manaus, Santarem and Rondonia), evaporation rates increased in the dry season, coincident with increased radiation. Evaporation rates were as high as 4.0 mm d(-1) in these evergreen or semidecidous forests. In contrast, ecosystems with precipitation less than 1700 mm and a longer dry season (Mato Grosso, Tocantins and Sao Paulo) showed clear evidence of reduced evaporation in the dry season. Evaporation rates were as low as 2.5 mm d(-1) in the transitional forests and 1 mm d(-1) in the cerrado. The controls on evapotranspiration seasonality changed along the biome gradient, with evaporative demand (especially net radiation) playing a more important role in the wetter forests, and soil moisture playing a more important role in the drier savannah sites.

The lipid composition of a cell membrane modulates the interaction of an antiparasitic peptide at the air-water interface

The antiparasitic property of peptides is believed to be associated with their interactions with the protozoan membrane, which calls for research on the identification of membrane sites capable of peptide binding. In this study we investigated the interaction of a lipophilicglutathioine peptide known to be effective against the African Sleeping Sickness (ASS - African Trypanosomiasis) and cell membrane models represented by Langmuir monolayers. It is shown that even small amounts of the peptide affect the monolayers of some phospholipids and other lipids, which points to a significant interaction. The latter did not depend on the electrical charge of the monolayer-forming molecules but the peptide action was particularly distinctive for cholesterol + sphingomyelin monolayers that roughly resemble rafts on a cell membrane. Using in situ polarization-modulated infrared reflection absorption spectroscopy (PM-IRRAS), we found that the orientation of the peptide is affected by the phospholipids and dioctadecyldimethylammonium bromide (DODAB), but not in monolayers comprising cholesterol + sphingomyelin. In this mixed monolayer resembling rafts, the peptide still interacts and has some induced order, probably because the peptide molecules are fitted together into a compact monolayer. Therefore, the lipid composition of the monolayer modulates the interaction with the lipophilic glutathioine peptide, and this may have important implications in understanding how the peptide acts on specific sites of the protozoan membrane. (C) 2011 Elsevier B.V. All rights reserved.

Properties of lipophilic nucleoside monolayers at the air-water interface

The capability of self-assembly and molecular recognition of biomolecules is essential for many nanotechnological applications, as in the use of alkyl-modified nucleosides and oligonucleotides to increase the cellular uptake of DNA and RNA. In this study, we show that a lipophilic nucleoside, which is an isomer mixture of 2`-palmitoyluridin und 3`-palmitoyluridin, forms Langmuir monolayers and Langmuir-Blodgett films as a typical amphiphile, though with a smaller elasticity. The nucleoside may be incorporated into dipalmitoyl phosphatidyl choline (DPPC) monolayers that serve as a simplified cell membrane model. The molecular-level interactions between the nucleoside and DPPC led to a remarkable condensation of the mixed monolayer, which affected both surface pressure and surface potential isotherms. The morphology of the mixed monolayers was dominated by the small domains of the nucleoside. The mixed monolayers could be deposited onto solid substrates as a one-layer Langmuir Blodgett film that displayed UV-vis absorption spectra typical of aggregated nucleosides owing to the interaction between the nucleoside and DPPC. The formation of solid films with DNA building blocks in the polar heads may open the way for devices and sensors be produced to exploit their molecular recognition properties. (C) 2010 Elsevier B.V. All rights reserved.

Risk of Giardia infection for drinking water and bathing in a peri-urban area in Sao Paulo, Brazil

A high incidence of waterborne diseases is observed worldwide and in order to address contamination problems prior to an outbreak, quantitative microbial risk assessment is a useful tool for estimating the risk of infection. The objective of this paper was to assess the probability of Giardia infection from consuming water from shallow wells in a peri-urban area. Giardia has been described as an important waterborne pathogen and reported in several water sources, including ground waters. Sixteen water samples were collected and examined according to the US EPA (1623, 2005). A Monte Carlo method was used to address the potential risk as described by the exponential dose response model. Giardia cysts occurred in 62.5% of the samples (0.1-36.1 cysts/l). A median risk of 10-1 for the population was estimated and the adult ingestion was the highest risk driver. This study illustrates the vulnerability of shallow well water supply systems in peri-urban areas.

Development of a sequential injection-square wave voltammetry method for determination of paraquat in water samples employing the hanging mercury drop electrode

This work describes the development and optimization of a sequential injection method to automate the determination of paraquat by square-wave voltammetry employing a hanging mercury drop electrode. Automation by sequential injection enhanced the sampling throughput, improving the sensitivity and precision of the measurements as a consequence of the highly reproducible and efficient conditions of mass transport of the analyte toward the electrode surface. For instance, 212 analyses can be made per hour if the sample/standard solution is prepared off-line and the sequential injection system is used just to inject the solution towards the flow cell. In-line sample conditioning reduces the sampling frequency to 44 h(-1). Experiments were performed in 0.10 M NaCl, which was the carrier solution, using a frequency of 200 Hz, a pulse height of 25 mV, a potential step of 2 mV, and a flow rate of 100 mu L s(-1). For a concentration range between 0.010 and 0.25 mg L(-1), the current (i(p), mu A) read at the potential corresponding to the peak maximum fitted the following linear equation with the paraquat concentration (mg L(-1)): ip = (-20.5 +/- 0.3) Cparaquat -(0.02 +/- 0.03). The limits of detection and quantification were 2.0 and 7.0 mu g L(-1), respectively. The accuracy of the method was evaluated by recovery studies using spiked water samples that were also analyzed by molecular absorption spectrophotometry after reduction of paraquat with sodium dithionite in an alkaline medium. No evidence of statistically significant differences between the two methods was observed at the 95% confidence level.

Rapid and direct determination of glyphosate and aminomethylphosphonic acid in water using anion-exchange chromatography with coulometric detection

A simple, rapid, and low-cost coulometric method for direct detection of glyphosate and aminomethylphosphonic acid (AMPA) in water samples using anion-exchange chromatography and coulometric detection with copper electrode is presented. Under optimized conditions, the limits of detection (LODs) (S/N = 3) were 0.038 mu g ml(-1) for glyphosate and 0.24 mu g ml(-1) for AMPA, without any preconcentration method. The calibration curves were linear and presented an excellent correlation coefficient. The method was successfully applied to the determination of glyphosate and AMPA in water samples without any kind of extraction, clean-up, or preconcentration step. No interferent was found in the water, like this, the recovery was, practically, 100%. (c) 2008 Elsevier B.V. All rights reserved.

Phenolic matrices and sisal fibers modified with hydroxy terminated polybutadiene rubber: Impact strength, water absorption, and morphological aspects of thermosets and composites

The aim of the present work was to investigate the toughening of phenolic thermoset and its composites reinforced with sisal fibers, using hydroxyl-terminated polybutadiene rubber (HTPB) as both impact modifier and coupling agent. Substantial increase in the impact strength of the thermoset was achieved by the addition 10% of HTPB. Scanning electron microscopy (SEM) images of the material with 15% HTPB content revealed the formation of some rubber aggregates that reduced the efficiency of the toughening mechanism. In composites, the toughening effect was observed only when 2.5% of HTPB was added. The rubber aggregates were found located mainly at the matrix-fiber interface suggesting that HTPB could be used as coupling agent between the sisal fibers and the phenolic matrix. A composite reinforced with sisal fibers pre-impregnated with HTPB was then prepared; its SEM images showed the formation of a thin coating of HTPB on the surface of the fibers. The ability of HTBP as coupling agent between sisal fibers and phenolic matrix was then investigated by preparing a composite reinforced with sisal fibers pre-treated with HTPB. As revealed by its SEM images, the HTPB pre-treatment of the fibers resulted on the formation of a thin coating of HTPB on the surface of the fibers, which provided better compatibility between the fibers and the matrix at their interface, resulting in a material with low water absorption capacity and no loss of impact strength. (C) 2009 Elsevier B.V. All rights reserved.

Evaluation of the QuEChERS Method and Gas Chromatography-Mass Spectrometry for the Analysis Pesticide Residues in Water and Sediment

A method for the determination of pesticide residues in water and sediment was developed using the QuEChERS method followed by gas chromatography - mass spectrometry. The method was validated in terms of accuracy, specificity, linearity, detection and quantification limits. The recovery percentages obtained for the pesticides in water at different concentrations ranged from 63 to 116%, with relative standard deviations below 12%. The corresponding results from the sediment ranged from 48 to 115% with relative standard deviations below 16%. The limits of detection for the pesticides in water and sediment were below 0.003 mg L(-1) and 0.02 mg kg(-1), respectively.

Laboratory model studies of flushing of trapped salt water from a blocked tidal estuary

Results are presented from a series of laboratory model studies of the flushing of saline water from a partially- or fully-closed estuary. Experiments have been carried out to determine quantitatively the response of the trapped saline volume to fresh water flushing discharges Q for different values of the estuary bed slope α and the density difference (∆ρ)_o between the saline and fresh water. The trapped saline water forms a wedge within the estuary and for maintained steady discharges, flow visualisation and density profile data confirm that its response to the imposition of the freshwater purging flow occurs in two stages, namely (i) an initial phase characterised by intense shear-induced mixing at the nose of the wedge and (ii) a relatively quiescent second phase where the mixing is significantly reduced and the wedge is forced relatively slowly down and along the bed slope. Scalings based upon simple energy balance considerations are shown to be successful in (i) describing the time-dependent wedge behaviour and (ii) quantifying the proportion of input kinetic energy converted into increasing the potential energy of the wedge/river system. Measurements show that the asymptotic value of the energy conversion factor increases with increasing value of the river Froude number Fr_o at small values of Fr_o, thereafter reaching a maximum value and a gradual decrease at the highest values of Fr_o. Dimensional analysis considerations indicate that the normalised, time-dependent wedge position (x_w)³(g')o/q² can be represented empirically by a power-law relationship of the form (x_w)[(g')_o/q²]^1/3 =C [(t)[(g')_o²/q]^1/3]"where the proportionality coefficient C is a function of both Fr_o and the slope angle α and the exponent n has a value of 0.24. Successful attempts are made to relate the model data to existing field observations from a microtidal estuary.

Experiments with multiple, intermittent periodic flushing flows confirm the importance of the starting phase of each flushing event for the time dependent behaviour of the saline wedge after reaching equilibrium in the intervals between such events. For the parameter ranges investigated and for otherwise-identical external conditions, no significant differences are found in the position of the wedge between cases of sequential multiple flushing flows and steady single discharges of the same total duration.

The effects of various binders and moisture content on pellet stability of research diets for freshwater crayfish

Two experiments were conducted to assess the water stability of a practical research diet manufactured with various binders and differing levels of moisture. In the first experiment the binders – agar, gelatine, carrageenan, and carboxymethylcellulose (CMC) were included at both 3 and 5% of total ingredient weight. All binders were tested with equal ingredient weight to water volume, and additionally carrageenan was tested in a diet with double the water volume. The dry matter remaining following immersion for up to 180 min was calculated and the rate of pellet decay was modelled using the Weibull distribution. The analysis revealed that the rate of dry matter loss decreased with time, and that carrageenan and CMC binders were significantly better (P < 0.001) binders than the agar and gelatine. The 5% binder concentration slowed the decay rate by as much as 62% as compared with the 3% binder concentration. The second experiment compared the binding performance of carrageenan and sodium alginate in both 50% moisture and 10% moisture pellets. The same analysis revealed that 10% moisture alginate-bound pellets were more water stable than the others. A discussion of the use of moist diets for crayfish research is included.

An integrative marketing channel performance measurement framework

This paper proposes a number of channel performance measurement research propositions. The paper reviews the strategy implementation, strategic control, marketing metrics, marketing channels and performance measurement literature to develop a conceptual model and research propositions. Current channel performance measurement guidelines are too generic for marketing managers and too reliant on financial measures. The introduction of contextual variables such as strategy, culture and manager's personality may provide measures more useful for an individual company's context and requirements. The alignment of channel measures with business strategy should result in more effective and efficient use of channel resources.

Assessing direct and indirect water requirements of construction

Australia is considered the driest populated continent in the world. Despite this, we consume the largest amount of water, per capita. While little of this water is used for the operation of buildings, buildings are now being designed to use less water. Additionally, rainwater collection and grey water recycling systems offer the potential to significantly reduce demand for fresh water. However, little is known about the water required directly and indirectly (ie., embodied in) construction materials and products. Embodied water comprises the water required directly for construction itself and the water consumed indirectly in the production and delivery of materials, products and services to construction. Water required directly for construction is likely to be insignificant compared to the indirect water required for the manufacture of construction materials and products (ie., through materials and other products required to support construction). There is currently a lack of research into embodied water requirements by the construction sector. The relationship between the embodied water and the operational water is also unknown, apart from a handful of studies based solely on national average statistics known as 'input-output' data. The aim of this paper is therefore to model the water required directly and indirectly by construction, integrating currently available public domain industry data with input-output data. The coverage of the industry data relative to the input-output data was evaluated for a typical commercial building, and was found to be very low.

Toward an integrative role for intranets : an interpretive case study of intranet-based dynamic knowledge integration in socio-technical networks

An increasing challenge for contemporary businesses is to be able to respond to perceived opportunities and threats by dynamically integrating knowledge dispersed across and beyond the organisation. This paper provides findings from two interpretive case studies that illustrate how corporate intranets can be dynamically interwoven with other knowledge technologies in socio-technical networks (STNs) to integrate distributed formal and infonnal knowledge. A key finding suggests that businesses should carefully examine employee use of intranets for dynamic knowledge integration, and any implications stemming from this new integrative role for intranets. The paper also provides a theoretical framework for dynamic knowledge integration in STNs, which can underpin future research in this area.