VALIDAÇÃO INTRALABORATORIAL DA DETERMINAÇÃO DE METILTESTOSTERONA EM ÁGUAS NATURAIS POR VOLTAMETRIA USANDO ELETRODO DE GOTA PENDENTE DE MERCÚRIO

17α-methyltestosterone (17α-MT) is a hormone used in medicine and aquaculture which can be found in natural waters. It is considered an emerging organic pollutant and its accurate and precise analysis is required. Therefore, this study presents the in-house validation of a new voltammetric methodology for 17α-MT analysis in natural waters. A hanging mercury drop electrode and NaOH 5.0×10-3 mol L-1 solution as the electrolyte were employed in the voltammetric determinations. To confirm the presence of 17α-MT in water samples quantitative analysis was performed by ESI-MS/MS. The methodology exhibited good selectivity, linearity, accuracy (recovery of between 100.4 and 108.8%) and precision (RSDs for repeatability of 2.85% and for intermediate precision of 14.10%, with n = 5, respectively). LOD and LOQ were 3.07 µg L-1 and 10.78 µg L-1, respectively. The methodology was suitable for determination of 17α-MT in natural waters due to low-cost, good performance and no sample pre-treatment required.

TREATMENT OF WASTE FROM ATOMIC EMISSION SPECTROMETRIC TECHNIQUES AND REUSE IN UNDERGRADUATE LAB CLASSES FOR QUALITATIVE ANALYSIS

Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma optical emission spectrometry (ICP OES) are widely used in academic institutions and laboratories for quality control to analyze inorganic elements in samples. However, these techniques have been observed to underperform in sample nebulization processes. Most of the samples processed through nebulization system are discarded, producing large volumes of waste. This study reports the treatment and reuse of the waste produced from ICP OES technique in a laboratory of analytical research at the Universidade Federal do Ceará, Brazil. The treatment of the waste was performed by the precipitation of elements using (NH4)2CO3. Subsequently, the supernatant solution can be discarded in accordance with CONAMA 430/2011. The precipitate produced from the treatment of residues can be reused as a potential sample in undergraduate qualitative analytical chemistry lab classes, providing students the opportunity to test a real sample.

COMPARAÇÃO DE MÉTODOS POR CROMATOGRAFIA LÍQUIDA NA DETERMINAÇÃO DE MULTIRRESÍDUOS DE AGROTÓXICOS EM MORANGOS

Liquid chromatography is often used for the determination of pesticide multiresidues in foods. In Brazil, the strawberry crop is an example of a food with high levels of irregularities because of the application of pesticides. This is a major concern from the perspective of food safety, environmental protection, and certification for food export. The purpose of this study is to evaluate and compare chromatographic separation and detection methods in relation to a newly developed and validated method using ultra high performance liquid chromatography (LC) coupled with tandem mass spectrometry (MS/MS) for the analytical determination of pesticides in strawberries. The comparisons were based on evaluations of the analysis time, consumption of the solvent in the mobile phase, injection volume, detectability, matrix effect, and recovery. The results showed that the LC–MS/MS and UHPLC–MS/MS techniques were both extremely efficient at analyzing pesticide residues with different physico-chemical parameters that were present at low concentrations in a complex matrix. The UHPLC separation method provided better chromatographic performance and productivity, which contributed favorably to routine analytical determinations. Detection by MS/MS had better detectability and selectivity compared with the diode array detector.

Flow injection spectrophotometric determination of adrenaline using a solid-phase reactor containing triiodide ions immobilized in an anion-exchange resin

A flow injection spectrophotometric procedure with on-line solid-phase reactor containing ion triiodide immobilized in an anion-exchange resin is proposed for the determination of adrenaline (epinephrine) in pharmaceutical products. Adrenaline is oxidized by triiodide ion immobilized in an anionic-exchange resin yielding adrenochrome which is transported by the carrier solution and detected at a wavelength of 488 nm. Adrenaline was determined in three pharmaceutical products in the 6.4 x 10-6 to 3.0 x 10-4 mol L-1 concentration range with a detection limit of 4.8 x 10-7 mol L-1. The recovery of this analyte in three samples ranged from 96.0 to 105 %. The analytical frequency was 80 determinations per hour and the RSDs were less than 1 % for adrenaline concentrations of 6.4 x 10-5 and 2.0 x 10-4 mol L-1 (n=10). A paired t-test showed that all results obtained for adrenaline in commercial formulations using the proposed flow injection procedure and a spectrophotometric batch procedure agree at the 95% confidence level.

Spectrophotometric study of iron oxidation in the iron(II)/thiocyanate/acetone system and some analytical applications

The possibility of using thiocyanate to determine iron(II) and/or iron(III) in water-acetone mixture has been re-examined as part of a systematic and comparative study involving metallic complexes of pseudohalide ligands. Some parameters that affect the complete oxidation of the ferrous cations, their subsequent complexation and the system stability have been studied to optimize the experimental conditions. Our results show the viability and potentiality of this simply methodology as an alternative analytical procedure to determine iron cations with high sensitivity, precision and accuracy. Studies on the calibration, stability, precision, and effect of various different ions have been carried out by using absorbance values measured at 480 nm. The analytical curve for the total iron determination obeys Beer's law (r = 0.9993), showing a higher sensitivity (molar absorptivity of 2.10x10(4) L cm-1 mol-1) when compared with other traditional systems (ligands) or even with the "similar" azide ion [1.53x10(4) L cm-1 mol-1, for iron-III/azide complexes, in 70% (v/v) tetrahydrofuran/water, at 396 nm]. Under such optimized experimental conditions, it is possible to determine iron in the concentration range from 0.5 to 2 ppm (15-65% T for older equipments, quartz cells of 1.00 cm). Analytical applications have been tested for some different materials (iron ores), also including pharmaceutical products for anemia, and results were compared with atomic absorption determinations. Very good agreement was obtained with these two different techniques, showing the potential of the present experimental conditions for the total iron spectrophotometric determinations (errors < 5%). The possibility of iron speciation was made evident by using another specific and auxiliary method for iron(II) or (III).

Determinação de cromo (VI) por espectrometria de absorção atômica com chama após a extração e pré-concentração no ponto nuvem

O presente trabalho reporta um método para a determinação de cromo (VI) por espectrometria de absorção atômica com chama (FAAS) após a extração e pré-concentração no ponto nuvem. O cromo (VI) é complexado com 1,5-difenilcarbazida (DFC) em meio ácido (pH 2,0) e é extraído para um volume de fase rica de 25 µL, com o uso do surfactante Triton X-114. As variáveis que afetam a formação do ponto nuvem, tais como a concentração de surfactante (0,1-1,0% m/v) e de complexante (0,01-0,80% m/v), o tempo de complexação (0-60 min) e o efeito da adição do eletrólito NaCl (0-20% m/v), são avaliadas. Sob condições otimizadas, são utilizados o Triton X-114 a 0,3% m/v, a DFC a 0,05% m/v e o NaCl a 10% m/v para a extração do cromo (VI). Esse método fornece limites de detecção e quantificação de 0,4 µg L-1 e 1,5 µg L-1, respectivamente, e uma faixa linear de calibração de 5 a 500 µg L-1. O fator de pré-concentração obtido é igual a 27 e a eficiência de extração varia de 87 a 99,3%.

Flow injection analysis of vancomycin

A flow injection method for the quantitative analysis of vancomycin hydrochloride, C66H75Cl2N9O24.HCl (HVCM), based on the reaction with copper (II) ions, is presented. HVCM forms a lilac-blue complex with copper ions at pH≅4.5 in aqueous solutions, with maximum absorption at 555 nm. The detection limit was estimated to be about 8.5×10-5 mol L-1; the quantitation limit is about 2.5×10-4 mol L-1 and about 30 determinations can be performed in an hour. The accuracy of the method was tested through recovery procedures in presence of four different excipients, in the proportion 1:1 w/w. The results were compared with those obtained with the batch spectrophotometric and with the HPLC methods. Statistical comparison was done using the Student's procedure. Complete agreement was found at a 0.95 significance level between the proposed flow injection and the batch spectrophotometric methods, which present similar precision (RSD: 2.1 % vs. 1.9%).

A novel indicator reaction for the catalytic determination of V(V) at ppb levels by the kinetic spectrophotometric method

A novel sensitive and relatively selective kinetic method is presented for the determination of V(V), based on its catalytic effect on the oxidation reaction of Ponceau Xylydine by potassium bromate in presence of 5-sulfosalicylic acid (SSA) as activator. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of Ponceau Xylydine at 640 nm between 0.5 to 7 min (the fixed time method) in H3PO4 medium at 25ºC. The effect of various parameters such as concentrations of H3PO4, SSA, bromate and Ponceau Xylydine, temperature and ionic strength on the rate of net reaction were studied. The method is free from most interferences, especially from large amounts of V(IV). The decrease in absorbance is proportional to the concentration of V(V) over the entire concentration range tested (1-15 ng mL−1) with a detection limit of 0.46 ng mL-1 (according to statistical 3Sblank/k criterion) and a coefficient of variation (CV) of 1.8% (for ten replicate measurement at 95% confidence level). The proposed method suffers few interferences such as Cr(VI) and Hg(II) ions. The method was successfully applied to the determination of V(V) in tap water, drinking water, bottled mineral water samples and a certified standard reference material such as SRM-1640 with satisfactory results. The vanadium contents of water samples were also determined by FAAS for a comparison. The recovery of spiked vanadium(V) was found to be quantitative and the reproducibility was satisfactory. It was observed that the results of the SRM 1640 were in good agreement with the certified value.

Determination of copper at wide range concentrations using instrumental features of high-resolution continuum source flame atomic absorption spectrometry

This work describes a method to determine Cu at wide range concentrations in a single run without need of further dilutions employing high-resolution continuum source flame atomic absorption spectrometry. Different atomic lines for Cu at 324.754 nm, 327.396 nm, 222.570 nm, 249.215 nm and 224.426 nm were evaluated and main figures of merit established. Absorbance measurements at 324.754 nm, 249.215 nm and 224.426 nm allows the determination of Cu in the 0.07 - 5.0 mg L-1, 5.0 - 100 mg L-1 and 100 - 800 mg L-1 concentration intervals respectively with linear correlation coefficients better than 0.998. Limits of detection were 21 µg L-1, 310 µg L-1 and 1400 µg L-1 for 324.754 nm, 249.215 nm and 224.426 nm, respectively and relative standard deviations (n = 12) were £ 2.7%. The proposed method was applied to water samples spiked with Cu and the results were in agreement at a 95% of confidence level (paired t-test) with those obtained by line-source flame atomic absorption spectrometry.

The Sottunga-Jurmo shear zone : structure and deformation history of a crustal-scale ductile shear zone in SW Finland

The aim of this study is to gain a better understanding of the structure and the deformation history of a NW-SE trending regional, crustal-scale shear structure in the Åland archipelago, SW Finland, called the Sottunga-Jurmo shear zone (SJSZ). Approaches involving e.g. structural geology, geochronology, geochemistry and metamorphic petrology were utilised in order to reconstruct the overall deformation history of the study area. The study therefore describes several features of the shear zone including structures, kinematics and lithologies within the study area, the ages of the different deformation phases (ductile to brittle) within the shear zone, as well as some geothermobarometric results. The results indicate that the SJSZ outlines a major crustal discontinuity between the extensively migmatized rocks NE of the shear zone and the unmigmatised, amphibolite facies rocks SW of the zone. The main SJSZ shows overall dextral lateral kinematics with a SW-side up vertical component and deformation partitioning into pure shear and simple shear dominated deformation styles that was intensified toward later stages of the deformation history. The deformation partitioning resulted in complex folding and refolding against the SW margin of the SJSZ, including conical and sheath folds, and in a formation of several minor strike-slip shear zones both parallel and conjugate to the main SJSZ in order to accommodate the regional transpressive stresses. Different deformation phases within the study area were dated by SIMS (zircon U-Pb), ID-TIMS (titanite U-Pb) and 40Ar/39Ar (pseudotachylyte wholerock) methods. The first deformation phase within the ca. 1.88 Ga rocks of the study area is dated at ca. 1.85 Ga, and the shear zone was reactivated twice within the ductile regime (at ca. 1.83 Ga and 1.79 Ga), during which the strain was successively increasingly partitioned into the main SJSZ and the minor shear zones. The age determinations suggest that the orogenic processes within the study area did not occur in a temporal continuum; instead, the metamorphic zircon rims and titanites show distinct, 10-20 Ma long breaks in deformation between phases of active deformation. The results of this study further imply slow cooling of the rocks through 600-700ºC so that at 1.79 Ga, 2 the temperature was still at least 600ºC. The highest recorded metamorphic pressures are 6.4-7.1 kbar. At the late stages or soon after the last ductile phase (ca. 1.79 Ga), relatively high-T mylonites and ultramylonites were formed, witnessing extreme deformation partitioning and high strain rates. After the rocks reached lower amphibolite facies to amphibolite-greenschist facies transitional conditions (ca. 500-550ºC), they cooled rapidly, probably due to crustal uplift and exhumation. The shear zone was reactivated at least once within the semi-brittle to brittle regime between ca. 1.79 Ga and 1.58 Ga, as evidenced by cataclasites and pseudotachylytes. In summary, the results of this study suggest that the Sottunga-Jurmo shear zone (and the South Finland shear zone) defines a major crustal discontinuity, and played a central role in accommodating the regional stresses during and after the Svecofennian orogeny.

Hjärtats vanor, tankens välvilja och handens gärning : dygd som vårdetiskt grundbegrepp

The main aim of the study is to elucidate the meaning and dimensions of the concept of „virtue‟, and to find the place of virtue in a caritative caring ethics, i.e. a caring ethics based on human love and mercy. The intention is to create a theory model which utilizes the possibilities of virtue in developing the caritative caring ethics as a whole. The caritative caring ethics has a universal potential – it is primarily not a professional ethics, but it may form a frame of reference and basis for formulating ethical codes, and for ethical discussions within different caring contexts. The hermeneutic approach of the study is inspired by Gadamer‟s philosophical hermeneutics combined with the view of hermeneutics as a hypothetical-deductive process. The study is guided by Eriksson‟s model of definition of concepts. The concept of „virtue‟ is studied focusing on its ethical dimensions. These ethical dimensions of virtue are seen as anchored to an inner ethos, whereas ethos stands for the ontological goodness, a basic notion of the Good that permeates the entity of the human being, and forms the base of the culture where he lives and acts. The overarching research questions are: 1. What is virtue? 2. What is „virtue‟ as a basic concept in caring science? 3. What place does virtue have in caritative caring ethics? The answer of the first question is mainly searched for by an ontological determination comprising partly an etymologic and semantic analysis of „virtue‟, and partly a determination of the essence of virtue. The answer to the second and third questions are mainly searched for using a contextual determination, where the purposive context and pragmatic features of virtue are studied in relation to caring ethics. The ontological and contextual determinations are brought together through hermeneutical interpretation, forming a new whole, which constitutes the results of the study. The results of the study are depicted in a theory model, in which the movement of virtue from ethos to deed is moulded as caritative caring ethics. The material of the study consists of dictionaries, texts written by Aristotle and St. Thomas Aquinas, articles, dissertations, and books, as well as parts of a pilot survey answered by 33 nurses. The results of the study show that the essence of virtue is primarily functional, not ethical. The ethical emerges when virtue is contextualized in a human communion. Virtue makes something fulfil its function well; makes the human being good, and gives him morals and morality. The human being needs prudence, love, and humility to acquire and develop the moral virtues. Virtue is a power, related to a value, which considering a caritative caring ethics consists of the caritas motif. Human love is shown through deeds, making the human being do what he is expected to do. Virtue, as an active power of becoming, affirms and clarifies the human being‟s ability to develop in the direction of the Good. Virtue becomes essential and unifying when morality appears in the human mind as auctoritas, an inner, prompting power based on divinity or a transcendental ethos. Together ethos and virtue create opportunities for an inner ethics based on voluntariness and joy in being and doing the true, the good, and the beautiful.

Selection of microorganisms producer of lipase for fat removal from biodiesel purification water

The objective this study has been the selection of lipase productor microorganism, for removal of oils and grease, in the pre-treatment of biodiesel wastewater washing. For this, analyses of the physicist-chemistries characteristics had been made with the wastewater of the biodiesel washing, and then it had been isolated and chosen, by means of determinations of the lipase activity. Following, it was made a test of fat biodegradation, in the conditions: pH (5.95), temperature (35 ºC), rotation (180 rpm) and ammonium sulfate as nitrogen source (3 g L-1) and establishing as variable the two microorganism preselected and the time (24; 48; 72; 96 and 120 h). The biodiesel purification wastewater had presented high potential of environmental impact, presenting a concentration of O of 6.76 g L-1. From the six isolated microbiological cultures, two microorganisms (A and B) had been selected, with enzymatic index of 0.56 and 0.57, respectively. The treatment of the wastewater using the isolated microorganism (Klebsiella oxytoca) had 80% of the fatty removal in 48 h.

LONG-TERM EFFECTS OF SWINE wastewater AND MINERAL FERTILIZER ASSOCIATION ON SOIL MICROBIOTA

ABSTRACT Swine wastewater (SW) application in agricultural soils may affect its microbial community in a long term. The objective of this study was to evaluate prospective changes in soil bacterial community after eight years continuous application of swine wastewater. The wastewater doses tested were 0; 100; 200 and 300 m3 ha-1, being applied from the beginning of the experiment and with or without recommended fertilization. Three soil samples were taken from each plot for determinations of basal respiration, microbial biomass and metabolic quotient. We also performed DGGE analysis and made a correlation between soil chemical conditions and microbial activity. Microbial community underwent significant structural changes from swine wastewater applications. Higher SW doses (200 and 300 m3 ha-1) influenced significantly (p <0.05) and benefitted certain bacteria groups.

Evaluation of PCR and multiplex PCR in relation to nested PCR for diagnosing Theileria equi

Conventional PCR (PCRTeq) for diagnosing Theileria equi and multiplex PCR (M/PCRTeq-Bc) for diagnosing T. equi and Babesia caballi were comparatively evaluated with nested PCR (N/PCR-Teq) for diagnosing equine piroplasmosis. In DNA sensitivity determinations, in multiple dilutions of equine blood that had tested positive for T. equi, PCR-Teq and N/PCR-Teq detected hemoparasite DNA in the larger dilutions (1:128), but did not differ significantly from the M/PCRTeq-Bc (1:64). In analyses on equine serum tested by ELISA, there was high agreement between this serological test and PCR-Teq (k = 0.780) and moderate agreement with N/PCR-Teq (k = 0.562) and M/PCRTeq-Bc (k = 0.488). PCR-Teq found a higher frequency of T. equi both in extensively and intensively reared horses, but this was not significant in relation to N/PCR-Teq (P>0.05), and both PCRs indicated that there was an endemic situation regarding T. equi in the population of horses of this sample. PCR-Teq was only significantly different from M/PCR-Teq-Bc (P<0.05). PCR-Teq presented high sensitivity and specificity, comparable to N/PCR-Teq, but with the advantage of higher speed in obtaining results and lower costs and risks of laboratory contamination. This accredits PCR-Teq for epidemiological studies and for determinations on affected horses.

Mineraalisen rakennusjätteen hyötykäyttö maarakentamisessa

Työn tavoitteena on osoittaa betonimurskeen ympäristökelpoisuus maarakennuskäytössä sekä vertailla betonimurskeen ja luonnonmateriaalien elinkaaren aikaisia ympäristövaikutuksia maarakentamisessa. Teoriaosassa käsitellään betonimurskeen maarakennuskäyttöön vaikuttavaa lainsäädäntöä ja sen mahdollisia ympäristövaikutuksia. Lisäksi käydään läpi neitseellisten maarakennusmate-riaalien otosta aiheutuvia ympäristövaikutuksia. Työn kokeellinen osa koostuu kahdesta osasta: materiaalien haitallisten aineiden liukoisuuden mää-rityksistä ja elinkaariarvioinnista. Liukoisuuden määritykset tehtiin kenttäkokeina luonnonolosuhteissa Lahden tiede- ja yrityspuisto Oy:n Jokimaan pilot-luokan maaperätutkimuskeskuksessa. Lisäksi liukoisuudet määritettiin laboratoriossa valtioneuvoston asetuksen eräiden jätteiden hyödyntämisestä maarakentamisessa vaatimusten mukaisesti. Elinkaariarvioinnissa vertailtiin betonimursketta neitseellisiin maarakennusmateriaaleihin skenaarioissa, jotka sisälsivät materiaalin valmistuksen ja kuljetuksen käyttökohteeseen. Neitseellisiä materiaaleja käytettäessä oletettiin, että betoni loppusijoitetaan kaatopaikalle. Elinkaariarvioinnissa käytettiin Gabi-elinkaarimallinnusohjelmaa ja skenaarioita vertailtiin hiilidioksidiekvivalenttipäästöihin. Lisäksi elinkaariarviointiin otettiin mukaan vielä kehitysvaiheessa oleva menetelmä maankäytön indikaattoreiden määrittämiseen. Menetelmällä tutkittiin soranoton vaikutusta soraharjun maaperän laadulle ennen ja jälkeen soranoton. Tulokseksi liukoisuuden määrityksistä saatiin, että betonimurskekerroksen läpi suotautuneen sade-veden pH nousee hyvin emäksiseksi. pH:n nousu vaikuttaisi korreloivan positiivisesti tiettyjen metallien liukoisuuteen. Huomattavaa on, että kenttäkokeiden liukoisuudet ja laboratoriossa määritetyt liukoisuudet poikkesivat joltain osin toisistaan. Elinkaaritarkastelussa hiilidioksidiekvivalentti päästöjen suhteen suurin päästö aiheutuu, jos betoni loppusijoitetaan kaatopaikalle hyötykäytön sijaan. Maaperän laadun muutoksien määrittämisen menetelmä ei vielä ole käyttökelpoinen lähtötietojen yksinkertaistuksien ja puutteiden takia. Betonimurskeen hyötykäyttö maarakentamisessa ei aiheuta merkittäviä ympäristövaikutuksia, kun altistus vedelle minimoidaan. Lisäksi hyötykäyttö on suositeltava vaihtoehto loppusijoitukselle kaatopaikan rakentamisen ja käytön aiheuttamien ympäristövaikutusten takia.