Electron and x-ray diffraction studies on Al86Fe14, Al82Fe18 and Al75Fe25 quasicrystals

Electron and x-ray diffraction experiments on the metlt-spun Al100−x Fe x (x=14, 18, 25) alloys are carried out. It is observed that all the melt-spun alloys possessing the quasi-crystalline phases have icosahedral point-group symmetry.

Experimental Studies on Drop Formation at the Tip of Melting Rods

Drop formation at the conical tips of melting rods has been experimentally studied using the transparent wax-alcohol/acetonitrile system. The effects of cone angle, rod diameter, immersion depth, and bath temperature on the detached drop mass have been studied over a wide range, besides recording useful qualitative information based on visual observation. The experimental results suggest that the phenomenon of drop formation at the tip of melting rods has a close parallel with the drop formation at conical tips, at least on a qualitative basis. However, the results could not be quantified owing to difficulties in characterizing the physical properties of the system, despite efforts to minimize them.

Spray erosion studies on pressed soil blocks

Erosion resistance of pressed soil blocks used for wall construction is discussed. The spray erosion test using a standardized shower spray is discussed. Spray erosion behaviour of pressed soil blocks made out of five different soils is presented. Results of laboratory and field tests are compared. Effect of clay content of the soil and density of the pressed soil block on erosion are discussed. Also the effect of water-proof coatings on erosion of soil blocks is presented. Erosion resistance of soil blocks stabilized with organic (jaggery syrup and starch) or inorganic binders is also discussed.

Crystallization studies on bulk SixTe100-x glasses

Bulk SixTe100-x (10 less-than-or-equals, slant x less-than-or-equals, slant 28) glasses have been prepared by the melt quenching technique. The crystallization of these glasses has been studied by using differential scanning calorimetry. The composition dependence of the glass transition temperature Tg, the recrystallization temperature Tcr and the melting temperature Tm show an unusual behaviour at the composition x congruent with 20. The glasses with 10 less-than-or-equals, slant x less-than-or-equals, slant 20 undergo double glass transition and double stage crystallization phenomena. On the other hand, glasses with 22 less-than-or-equals, slant x less-than-or-equals, slant 28 exhibit eutectic crystallization. The phases at different stages of crystallization have been identified by using X-ray diffraction techniques. The unusual behaviour at x congruent with 20 can be explained on the basis of the changes in the network topologies of IV-VI chalcogenide glasses.

Substrata Uralica : Studies on Finno-Ugrian Substrate in Northern Russian Dialects

The thesis consists of five articles and an introduction. It treats the problems of the Uralic substrate, most notably, the substrate toponyms, in the Russian dialects of Arkhangelsk region. The articles contribute to the general linguistic discussion concerning the nature of linguistic substrate and the outcome of language shift and to the onomastic discussion concerning the etymologisation and ethnic interpretation of substrate toponymy. Among the questions the articles scrutinised are the following: 1) How may phonetic and morphosyntactic substrate interference be verified? 2) How typical is the transfer of vocabulary in the case of a language shift? 3) How the borrowing of toponymy and appellative vocabulary are connected in the case of a language shift? 4) How does the etymologisation of the toponyms differ from the etymologisation of appellatives? 5) How reliable can the toponymic etymologies be? 6) How can the substrate language be identified? It is found that the substrate interference that can be meaningfully studied, from the point of view of historical linguistics, is predominantly lexical and not related to phonetics and morphosyntax, as presumed in many handbooks. New methods are outlined for the identification of substrate languages separately from the lexical, phonological and typological point of view by using the substrate toponymy as the main source of information on extinct languages. A reliability scale for the toponymic etymologies is developed that helps to identify the kinds of etymologies containing ethnohistorically meaningful information. The study also sheds light on questions related to Uralistics and Slavistics. The most important of these are the following: 1) Which Uralic languages were spoken in North Russia prior to Slavic? 2) When did the Slavicisation of the Finno-Ugrian population take place in the area of the Arkhangelsk Region? 3) What is the significance of the Finno-Ugrian substrate in northern Russian dialects to comparative Uralistics? 4) Are there any traces of pre-Uralic substrate languages in north-eastern Europe? The Finnic substrate languages, already identified by earlier studies, seem to have consisted of two groups, one of which was closest to the southern Finnic. Also, language(s) close to Sámi in some respects though not identical with it where spoken in pre-Slavic North Russia.

Process studies of odour emissions from effluent ponds using machine-based odour measurement

Replicable experimental studies using a novel experimental facility and a machine-based odour quantification technique were conducted to demonstrate the relationship between odour emission rates and pond loading rates. The odour quantification technique consisted of an electronic nose, AromaScan A32S, and an artificial neural network. Odour concentrations determined by olfactometry were used along with the AromaScan responses to train the artificial neural network. The trained network was able to predict the odour emission rates for the test data with a correlation coefficient of 0.98. Time averaged odour emission rates predicted by the machine-based odour quantification technique, were strongly correlated with volatile solids loading rate, demonstrating the increased magnitude of emissions from a heavily loaded effluent pond. However, it was not possible to obtain the same relationship between volatile solids loading rates and odour emission rates from the individual data. It is concluded that taking a limited number of odour samples over a short period is unlikely to provide a representative rate of odour emissions from an effluent pond. A continuous odour monitoring instrument will be required for that more demanding task.

1H and 13C dynamic NMR studies of NN-diethyl N'-aryl thioureas

The variable temperature 1H and 13C NMR behaviour of two trisubstituted thioureas, namely N,N-diethyl N'-(2-thiazolyl) thiourea and N,N-diethyl N'-(3-pyridyl)thiourea has been investigated. The barrier to rotation of the diethylamino group has been obtained.

Helix-coil stability constants for amino acids in nonaqueous solvents. Studies of random poly(-benzyl-L-glutamate-co-L-alanine) and poly(-benzyl-L-glutamate-co-L-leucine) in a mixed solvent

The host-guest technique has been applied to the determination of the helix-coil stability constants of two naturally occurring amino acids, L-alanine and L-leucine, in a nonaqueous solvent system. Random copolymers containing L-alanine and L-leucine, respectively, as guest residues and -benzyl-L-glutamate as the host residue were synthesized. The polymers were fractionated and characterized for their amino acid content, molecular weight, and helix-coil transition behavior in a dichloroacetic acid (DCA)-1,2-dichloroethane (DCE) mixture. Two types of helix-coil transitions were carried out on the copolymers: solvent-induced transitions in DCA-DCE mixtures at 25°C and thermally induced transitions in a 82:18 (wt %) DCA-DCE mixture. The thermally induced transitions were analyzed by statistical mechanical methods to determine the Zimm-Bragg parameters, and s, of the guest residues. The experimental data indicate that, in the nonaqueous solvent, the L-alanine residue stabilizes the -helical conformation more than the L-leucine residue does. This is in contrast to their behavior in aqueous solution, where the reverse is true. The implications of this finding for the analysis of helical structures in globular proteins are discussed.

Nonverbal predication in Erzya : Studies on morphosyntactic variation and part of speech distinctions

This dissertation consists of four articles and an introduction. The five parts address the same topic, nonverbal predication in Erzya, from different perspectives. The work is at the same time linguistic typology and Uralic studies. The findings based on a large corpus of empirical Erzya data, which was collected using several different methods and included recordings of the spoken language, made it possible for the present study to apply, then test and finally discuss the previous theories based on cross-linguistic data. Erzya makes use of multiple predication patterns which vary from totally analytic to the morphologically very complex. Nonverbal predicate clause types are classified on the basis of propositional acts in clauses denoting class-membership, identity, property and location. The predicates of these clauses are nouns, adjectives and locational expressions, respectively. The following three predication strategies in Erzya nonverbal predication can be identified: i. the zero-copula construction, ii. the predicative suffix construction and iii. the copula construction. It has been suggested that verbs and nouns cannot be clearly distinguished on morphological grounds when functioning as predicates in Erzya. This study shows that even though predicativity must not be considered a sufficient tool for defining parts of speech in any language, the Erzya lexical classes of adjective, noun and verb can be distinguished from each other also in predicate position. The relative frequency and degree of obligation for using the predicative suffix construction decreases when moving left to right on the scale verb adjective/locative noun ( identificational statement). The predicative suffix is the main pattern in the present tense over the whole domain of nonverbal predication in Standard Erzya, but if it is replaced it is most likely to be with a zero-copula construction in a nominal predication. This study exploits the theory of (a)symmetry for the first time in order to describe verbal vs. nonverbal predication. It is shown that the asymmetry of paradigms and constructions differentiates the lexical classes. Asymmetrical structures are motivated by functional level asymmetry. Variation in predication as such adds to the complexity of the grammar. When symmetric structures are employed, the functional complexity of grammar decreases, even though morphological complexity increases. The genre affects the employment of predication strategies in Erzya. There are differences in the relative frequency of the patterns, and some patterns are totally lacking from some of the data. The clearest difference is that the past tense predicative suffix construction occurs relatively frequently in Standard Erzya, while it occurs infrequently in the other data. Also, the predicative suffixes of the present tense are used more regularly in written Standard Erzya than in any other genre. The genre also affects the incidence of the translative in uľ(ń)ems copula constructions. In translations from Russian to Erzya the translative case is employed relatively frequently in comparison to other data. This study reveals differences between the two Mordvinic languages Erzya and Moksha. The predicative suffixes (bound person markers) of the present tense are used more regularly in Moksha in all kinds of nonverbal predicate clauses compared to Erzya. It should further be observed that identificational statements are encoded with a predicative suffix in Moksha, but seldom in Erzya. Erzya clauses are more frequently encoded using zero-constructions, displaying agreement in number only.

Numerical studies on columnar-to-equiaxed transition in directional solidification of binary alloys

A numerical study on columnar-to-equiaxed transition (CET) during directional solidification of binary alloys is presented using a macroscopic solidification model. The position of CET is predicted numerically using a critical cooling rate criterion reported in literature. The macroscopic solidification model takes into account movement of solid phase due to buoyancy, and drag effect on the moving solid phase because of fluid motion. The model is applied to simulate the solidification process for binary alloys (Sn-Pb) and to estimate solidification parameters such as position of the liquidus, velocity of the liquidus isotherm, temperature gradient ahead of the liquidus, and cooling rate at the liquidus. Solidification phenomena under two cooling configurations are studied: one without melt convection and the other involvin thermosolutal convection. The numerically predicted positions of CET compare well with those of experiments reported in literature. Melt convection results in higher cooling rate, higher liquidus isotherm velocities, and stimulation of occurrence of CET in comparison to the nonconvecting case. The movement of solid phase aids further the process of CET. With a fixed solid phase, the occurrence of CET based on the same critical cooling rate is delayed and it occurs at a greater distance from the chill.

Managing mycotoxins in maize: Case studies

Mycotoxin contamination of Australian maize is neither common nor extensive, but has the capacity to seriously disrupt marketing. Low to moderate levels of aflatoxins and fumonisins can be widespread in some seasons, but zearalenone, nivalenol and deoxynivalenol are usually confined to small growing localities. Possible approaches to such situations were tested by an analysis of several case studies. It is concluded that communication and coordination across the industry, prediction and prevention of contamination, rapid detection and assessment of contamination, effective use of contaminated maize and breeding for resistance comprise a useful set of strategies for managing mycotoxins in maize.

Laboratory studies on Australian isolates of Metarhizium anisopliae as a biopesticide for the cattle tick Boophilus microplus

Thirty-one isolates of Metarhizium anisopliae were bioassayed against the cattle tick (Boophilus microplus). More than half of the isolates showed a high degree of virulence to ticks. Radial growth curves for growth between 20 °C and 40 °C were obtained for all isolates. This information together with information on virulence will be important for the selection of isolates suitable to kill ticks on the surface of cattle. A biopesticide for cattle ticks must kill ticks rapidly at temperatures within the upper end of most isolates' growth curves. It was also found that the time taken to achieve 100% tick mortality in vitro using a virulent isolate could be halved by applying conidia in a 10% oil emulsion. Scanning electron microscopy and light microscopy were used to investigate and compare the germination and penetration of conidia formulated in aqueous and oil formulations. It was found that conidia in both formulations were able to germinate and produce appressoria on the surface of ticks in less than 11 h. Marked weakness within 26 h, followed by extensive hyphal growth on the cuticle characterised the invasion of ticks by M. anisopliae.

Pen studies on the control of cattle tick (Rhipicephalus (Boophilus) microplus) with Metarhizium anisopliae (Sorokin)

Three field trials were conducted over 12 months to assess the pathogenicity of Metarhizium anisopliae to parasitic stages of Rhipicephalus (Boophilus) microplus on dairy heifers under different environmental conditions. Two isolates were selected based on their high optimal growth temperature (30 °C), good spore production characteristics and ability to quickly kill adult engorged ticks in the laboratory. Spores were formulated in an oil emulsion and applied using a motor driven spray unit. Surface temperatures of selected animals were monitored, as were the ambient temperature and relative humidity. Unengorged ticks sampled from each animal immediately after treatment were incubated in the laboratory to assess the efficacy of the formulation and application. Egg production by engorged ticks collected in the first 3 days after treatment was monitored. Side counts of standard adult female ticks were conducted daily, before and after treatment to assess the performance of the fungus against all tick stages on the animals. In each trial the formulation rapidly caused 100% mortality in unengorged ticks that were removed from cattle and cultured in the laboratory. A significant reduction in egg production was recorded for engorged ticks collected in the 3 days post-treatment. However, there was little effect of the formulation on the survival of ticks on cattle, indicating that there is an interaction between the environment of the ticks on the cattle and the biopesticide, which reduces its efficacy against ticks.

Crystallographic and modelling studies on Mycobacterium tuberculosis RuvA: Additional role of RuvB-binding domain and inter species variability

RuvA, along with RuvB, is involved in branch migration of heteroduplex DNA in homologous recombination. The structures of three new crystal forms of RuvA from Mycobacterium tuberculosis (MtRuvA) have been determined. The RuvB-binding domain is cleaved off in one of them. Detailed models of the complexes of octameric RuvA from different species with the Holliday junction have also been constructed. A thorough examination of the structures presented here and those reported earlier brings to light the hitherto unappreciated role of the RuvB-binding domain in determining inter-domain orientation and oligomerization. These structures also permit an exploration of the interspecies variability of structural features such as oligomerization and the conformation of the loop that carries the acidic pin, in terms of amino acid substitutions. These models emphasize the additional role of the RuvB-binding domain in Holliday junction binding. This role along with its role in oligomerization could have important biological implications.