Die Beendigung von finnischen und deutschen Telefonaten. Eine interaktionslinguistische, kontrastierende Untersuchung

Suomalaisten ja saksalaisten arkikeskustelujen välillä on sekä yhtäläisyyksiä että eroja. Tässä saksalaisen filologian alaan kuuluvassa tutkimuksessa tarkastellaan yhtä keskeistä arkikeskustelun toimintoa, puhelinkeskustelun lopetusta, suomen- ja saksanpuhujien tuottamana. Aineistona on käytetty suomen- ja saksankielisten äidinkielisten puhujien tätä tutkimusta varten nauhoittamia henkilökohtaisia luonnollisia puhelinkeskusteluja. Aineistoon valikoitui 12 suomalaista ja 12 saksalaista puhelua. Nauhoitteiden käyttöön on saatu asianmukainen lupa kaikilta osapuolilta. Puhelut on litteroitu saksalaisella kielialueella vakiintuneen GAT-litterointisysteemin mukaan. Teoreettis-metodisena kehyksenä on kaksi tutkimusalaa, vuorovaikutuslingvistiikka ja kielten vertailu. Vuorovaikutuslingvistinen tarkastelu keskittyy havaintoihin vuorojen ja puheen sekvenssien rakenteesta. Vuorojen merkitysten tulkinnassa hyödynnetään systemaattisesti prosodian antamia vihjeitä. Tuloksena on yksittäisten lopetusten keskustelunanalyyttinen lähikuvaus, jonka pohjalta määritellään kulloisenkin lopetuksen sekvenssirakenne. Kaikki lopetukset olivat siltä osin yhteneväisiä, että niissä kaikissa havaittiin ainakin aloittava, tulevaan tapaamiseen viittaava sekä lopputervehdyksiin johtava sekvenssi. Sekvenssirakenteen variaatioiden pohjalta aineiston lopetukset voidaan kuitenkin jaotella ryhmiin. Sekä suomen- että saksankielisessä aineistossa havaittiin kolmentyyppisiä lopetuksia: kompakteja, komplekseja ja keskeytettyjä lopetuksia. Ryhmittely kolmeen tyyppiin on avuksi seuraavassa kuvausvaiheessa, jossa verrataan suomen- ja saksankielisiä lopetuksia toisiinsa. Samanaikaisesti kun tutkimus valottaa kohtia, joissa kaksi aineistosettiä yhtenevät ja eroavat, se myös esittää, mitkä vuorovaikutuksen tasot soveltuvat kieltenvälisen vertailun kohteiksi. Pohdintaa siitä, mitä vuorovaikutuksen tasoja kieltenväliseen vertailuun voidaan sisällyttää, onkin toistaiseksi esitetty verrattain vähän. Työ siis rakentaa siltaa vuorovaikutuslingvistisen ja kontrastiivisen kielitieteen välille.

Simulation of new p-type pixel strip detector with enhanced multiplication effect

This Master’s Thesis is dedicated to the simulation of new p-type pixel strip detector with enhanced multiplication effect. It is done for high-energy physics experiments upgrade such as Super Large Hadron Collider especially for Compact Muon Solenoid particle track silicon detectors. These detectors are used in very harsh radiation environment and should have good radiation hardness. The device engineering technology for developing more radiation hard particle detectors is used for minimizing the radiation degradation. New detector structure with enhanced multiplication effect is proposed in this work. There are studies of electric field and electric charge distribution of conventional and new p-type detector under reverse voltage bias and irradiation. Finally, the dependence of the anode current from the applied cathode reverse voltage bias under irradiation is obtained in this Thesis. For simulation Silvaco Technology Computer Aided Design software was used. Athena was used for creation of doping profiles and device structures and Atlas was used for getting electrical characteristics of the studied devices. The program codes for this software are represented in Appendixes.

Linear prediction in optical spectroscopy

A linear prediction procedure is one of the approved numerical methods of signal processing. In the field of optical spectroscopy it is used mainly for extrapolation known parts of an optical signal in order to obtain a longer one or deduce missing signal samples. The first is needed particularly when narrowing spectral lines for the purpose of spectral information extraction. In the present paper the coherent anti-Stokes Raman scattering (CARS) spectra were under investigation. The spectra were significantly distorted by the presence of nonlinear nonresonant background. In addition, line shapes were far from Gaussian/Lorentz profiles. To overcome these disadvantages the maximum entropy method (MEM) for phase spectrum retrieval was used. The obtained broad MEM spectra were further underwent the linear prediction analysis in order to be narrowed.

Transient current technique simulation of semiconductor detectors

Nowadays advanced simulation technologies of semiconductor devices occupies an important place in microelectronics production process. Simulation helps to understand devices internal processes physics, detect new effects and find directions for optimization. Computer calculation reduces manufacturing costs and time. Modern simulation suits such as Silcaco TCAD allow simulating not only individual semiconductor structures, but also these structures in the circuit. For that purpose TCAD include MixedMode tool. That tool can simulate circuits using compact circuit models including semiconductor structures with their physical models. In this work, MixedMode is used for simulating transient current technique setup, which include detector and supporting electrical circuit. This technique was developed by RD39 collaboration project for investigation radiation detectors radiation hard properties.

Ydinvoimalaitosten vesikemia ja korroosionesto

Ydinvoimalaitosten vesikemian optimointi ja korroosionesto on välttämätöntä laitosten taloudellisen ja turvallisen käytön kannalta. Eri laitoksiin liittyvää vesikemiaa ja järjestelmissä havaittavia korroosion muotoja on tutkittu laajasti ja tutkitaan yhä edelleen. Monien prosessien ymmärtäminen vaatii usean eri tieteenalan osaamista, kuten kemiantekniikan, energiatekniikan sekä materiaalitekniikan. Tässä työssä kerrotaan yksinkertaistaen vesikemiaan ja korroosioon liittyviä prosesseja ja reaktioita. Työssä käsitellään kevytvettä jäähdytteenä sekä moderaattorina käyttävien ydinvoimalaitosten eri korroosiomuotoja sekä säteilyn vaikutusta näihin suoraan tai vesikemian kautta. Työssä kerrotaan korroosio- ja aktivoitumistuotteiden muodostumisesta ja kulkeutumisesta sekä näiden tuotteiden vaikutuksista laitosten toimintaan. Korroosion ja materiaalien aktivoitumisen pohjalta tarkastellaan kattavasti ydinvoimalaitosten tyypillisimpiä vesikemian muokkauskeinoja sekä korroosionhallintaa. Tärkeimpiin asioihin syvennytään hieman lähemmin. Tarkastelun kohteena ovat eniten käytetyt ydinvoimalaitokset, eli länsimaiset paine- ja kiehutusvesilaitokset sekä venäläisvalmisteiset VVER-laitokset. Tarkoituksena on ollut luoda tiivis tietopaketti opiskelijoiden käyttöön muun opintomateriaalin tueksi.

Sunflower response to repeated foliar applications of Paclobutrazol

Paclobutrazol (PBZ), a well-known growth retardant of the triazole family, is mostly used for controlling plant size and growth, resulting in more desirable compact plants for floricultural purposes; however, limited experimental data are available for use of PBZ in field sunflower. The objective of this study was to evaluate the effect of repeated foliar applications of PBZ at rates of 50 + 50 g ha-1(double application) and 50 + 50 + 50 g ha-1 (triple application) on sunflower morphology and productivity. PBZ applications corresponded to growth stages of four to five, five to six, and six to eight true leaves of sunflower plants, respectively. The double foliar application of PBZ reduced sunflower plant height at maturity by 4.4% (or by 11.7 cm). The triple foliar application of PBZ reduced sunflower plant height at maturity by 14.4% (or by 49.2 cm). However, PBZ either in the double or the triple application reduced achene yield per plant by 25.6% and 22.5% and the 100-achene weight by 11.4% and 25.0%, respectively, compared with the non-treated control. Overall, the repeated foliar applications of PBZ at the rates tested in this study, apart from providing a reduction of sunflower plant height, had major adverse effects on achene yield and weight. Thus, different application schemes of PBZ or perhaps different growth regulators should be investigated to control plant height in sunflower.

Vegetative propagation strategies of four rupestrian species of Leiothrix (Eriocaulaceae)

Leiothrix is endemic of South America and includes 37 species, 25 of which occur in the state of Minas Gerais. Nineteen of those occur in the "Serra do Cipó", a mountain chain, located in the southern portion of the Espinhaço mountain range. This study examines vegetative propagation strategies of four species of Leiothrix, endemic to the Minas Gerais portion of the Espinhaço mountain range. For each species we established permanent plots, where we marked 30 to 51 rosettes or clones, and then took morphological and phenological measurements. Leiothrix crassifolia (Bong.) Ruhland and L. curvifolia var. lanuginosa (Bong.) Ruhland are rhizomatous, forming compact clones. Leiothrix vivipara (Bong.) Ruhland does not produce rhizomes, but is pseudoviviparous, i.e., produces numerous ramets originating from inflorescences. These ramets are formed precociously, and the flower heads do not touch the ground. In Leiothrix spiralis (Bong.) Ruhland both of these strategies are seen: it is both rhizomatous and pseudoviviparous. In this species, the ramets are formed late, only after the flower head has touched the ground. One of the typical conditions of the rupestrian grasslands is soil water shortage in some periods of the year and nutrient scarcity all year round. These conditions might have created an ideal ecological scenario for the evolution of both pseudovivipary and rhizomatous clonal growth in Leiothrix.

The interplay of JNK and SCG10 during cortical development and in excitotoxic responses in brain

Initially identified as stress activated protein kinases (SAPKs), the c-Jun Nterminal kinases (JNKs) are currently accepted as potent regulators of various physiologically important cellular events. Named after their competence to phosphorylate transcription factor c-Jun in response to UVtreatment, JNKs play a key role in cell proliferation, cell death or cell migration. Interestingly, these functions are crucial for proper brain formation. The family consists of three JNK isoforms, JNK1, JNK2 and JNK3. Unlike brain specific JNK3 isoform, JNK1 and JNK2 are ubiquitously expressed. It is estimated that ten splice variants exist. However, the detailed cellular functions of these remain undetermined. In addition, physiological conditions keep the activities of JNK2 and JNK3 low in comparison with JNK1, whereas cellular stress raises the activity of these isoforms dramatically. Importantly, JNK1 activity is constitutively high in neurons, yet it does not stimulate cell death. This suggests a valuable role for JNK1 in brain development, but also as an important mediator of cell wellbeing. The aim of this thesis was to characterize the functional relationship between JNK1 and SCG10. We found that SCG10 is a bona fide target for JNK. By employing differential centrifugation we showed that SCG10 co-localized with active JNK, MKK7 and JIP1 in a fraction containing endosomes and Golgi vesicles. Investigation of JNK knockout tissues using phosphospecific antibodies recognizing JNK-specific phosphorylation sites on SCG10 (Ser 62/Ser 73) showed that phosphorylation of endogenous SCG10 was dramatically decreased in Jnk1-/- brains. Moreover, we found that JNK and SCG10 co-express during early embryonic days in brain regions that undergo extensive neuronal migration. Our study revealed that selective inhibition of JNK in the cytoplasm significantly increased both the frequency of exit from the multipolar stage and radial migration rate. However, as a consequence, it led to ill-defined cellular organization. Furthermore, we found that multipolar exit and radial migration in Jnk1 deficient mice can be connected to changes in phosphorylation state of SCG10. Also, the expression of a pseudo-phosphorylated mutant form of SCG10, mimicking the JNK1- phopshorylated form, brings migration rate back to normal in Jnk1 knockout mouse embryos. Furthermore, we investigated the role of SCG10 and JNK in regulation of Golgi apparatus (GA) biogenesis and whether pathological JNK action could be discernible by its deregulation. We found that SCG10 maintains GA integrity as with the absence of SCG10 neurons present more compact fragmented GA structure, as shown by the knockdown approach. Interestingly, neurons isolated from Jnk1-/- mice show similar characteristics. Block of ER to GA is believed to be involved in development of Parkinson's disease. Hence, by using a pharmacological approach (Brefeldin A treatment), we showed that GA recovery is delayed upon removal of the drug in Jnk1-/- neurons to an extent similar to the shRNA SCG10-treated cells. Finally, we investigated the role of the JNK1-SCG10 duo in the maintenance of GA biogenesis following excitotoxic insult. Although the GA underwent fragmentation in response to NMDA treatment, we observed a substantial delay in GA disintegration in neurons lacking either JNK1 or SCG10.

Ultrasonic and Electrokinetic Remediation of Low Permeability Soil Contaminated with Persistent Organic Pollutants

Electrokinetics has emerged as a potential technique for in situ soil remediation and especially unique because of the ability to work in low permeability soil. In electrokinetic remediation, non-polar contaminants like most organic compounds are transported primarily by electroosmosis, thus the process is effective only if the contaminants are soluble in pore fluid. Therefore, enhancement is needed to improve mobility of these hydrophobic compounds, which tend to adsorb strongly to the soil. On the other hand, as a novel and rapidly growing science, the applications of ultrasound in environmental technology hold a promising future. Compared to conventional methods, ultrasonication can bring several benefits such as environmental friendliness (no toxic chemical are used or produced), low cost, and compact instrumentation. It also can be applied onsite. Ultrasonic energy applied into contaminated soils can increase desorption and mobilization of contaminants and porosity and permeability of soil through developing of cavitation. The research investigated the coupling effect of the combination of these two techniques, electrokinetics and ultrasonication, in persistent organic pollutant removal from contaminated low permeability clayey soil (with kaolin as a model medium). The preliminary study checked feasibility of ultrasonic treatment of kaolin highly contaminated by persistent organic pollutants (POPs). The laboratory experiments were conducted in various conditions (moisture, frequency, power, duration time, initial concentration) to examine the effects of these parameters on the treatment process. Experimental results showed that ultrasonication has a potential to remove POPs, although the removal efficiencies were not high with short duration time. The study also suggested intermittent ultrasonication over longer time as an effective means to increase the removal efficiencies. Then, experiments were conducted to compare the performances among electrokinetic process alone and electrokinetic processes combined with surfactant addition and mainly with ultrasonication, in designed cylinders (with filtercloth separating central part and electrolyte parts) and in open pans. Combined electrokinetic and ultrasonic treatment did prove positive coupling effect compared to each single process alone, though the level of enhancement is not very significant. The assistance of ultrasound in electrokinetic remediation can help reduce POPs from clayey soil by improving the mobility of hydrophobic organic compounds and degrading these contaminants through pyrolysis and oxidation. Ultrasonication also sustains higher current and increases electroosmotic flow. Initial contaminant concentration is an essential input parameter that can affect the removal effectiveness.

Liquid cooling solutions for rotating permanent magnet synchronous machines

In the design of electrical machines, efficiency improvements have become very important. However, there are at least two significant cases in which the compactness of electrical machines is critical and the tolerance of extremely high losses is valued: vehicle traction, where very high torque density is desired at least temporarily; and direct-drive wind turbine generators, whose mass should be acceptably low. As ever higher torque density and ever more compact electrical machines are developed for these purposes, thermal issues, i.e. avoidance of over-temperatures and damage in conditions of high heat losses, are becoming of utmost importance. The excessive temperatures of critical machine components, such as insulation and permanent magnets, easily cause failures of the whole electrical equipment. In electrical machines with excitation systems based on permanent magnets, special attention must be paid to the rotor temperature because of the temperature-sensitive properties of permanent magnets. The allowable temperature of NdFeB magnets is usually significantly less than 150 ˚C. The practical problem is that the part of the machine where the permanent magnets are located should stay cooler than the copper windings, which can easily tolerate temperatures of 155 ˚C or 180 ˚C. Therefore, new cooling solutions should be developed in order to cool permanent magnet electrical machines with high torque density and because of it with high concentrated losses in stators. In this doctoral dissertation, direct and indirect liquid cooling techniques for permanent magnet synchronous electrical machines (PMSM) with high torque density are presented and discussed. The aim of this research is to analyse thermal behaviours of the machines using the most applicable and accurate thermal analysis methods and to propose new, practical machine designs based on these analyses. The Computational Fluid Dynamics (CFD) thermal simulations of the heat transfer inside the machines and lumped parameter thermal network (LPTN) simulations both presented herein are used for the analyses. Detailed descriptions of the simulated thermal models are also presented. Most of the theoretical considerations and simulations have been verified via experimental measurements on a copper tooth-coil (motorette) and on various prototypes of electrical machines. The indirect liquid cooling systems of a 100 kW axial flux (AF) PMSM and a 110 kW radial flux (RF) PMSM are analysed here by means of simplified 3D CFD conjugate thermal models of the parts of both machines. In terms of results, a significant temperature drop of 40 ̊C in the stator winding and 28 ̊C in the rotor of the AF PMSM was achieved with the addition of highly thermally conductive materials into the machine: copper bars inserted in the teeth, and potting material around the end windings. In the RF PMSM, the potting material resulted in a temperature decrease of 6 ̊C in the stator winding, and in a decrease of 10 ̊C in the rotor embedded-permanentmagnets. Two types of unique direct liquid cooling systems for low power machines are analysed herein to demonstrate the effectiveness of the cooling systems in conditions of highly concentrated heat losses. LPTN analysis and CFD thermal analysis (the latter being particularly useful for unique design) were applied to simulate the temperature distribution within the machine models. Oil-immersion cooling provided good cooling capability for a 26.6 kW PMSM of a hybrid vehicle. A direct liquid cooling system for the copper winding with inner stainless steel tubes was designed for an 8 MW directdrive PM synchronous generator. The design principles of this cooling solution are described in detail in this thesis. The thermal analyses demonstrate that the stator winding and the rotor magnet temperatures are kept significantly below their critical temperatures with demineralized water flow. A comparison study of the coolant agents indicates that propylene glycol is more effective than ethylene glycol in arctic conditions.

Biogas production in regional integrated biodegradable waste treatment – Possibilities for improving energy performance and reducing GHG emissions

The greatest threat that the biodegradable waste causes on the environment is the methane produced in landfills by the decomposition of this waste. The Landfill Directive (1999/31/EC) aims to reduce the landfilling of biodegradable waste. In Finland, 31% of biodegradable municipal waste ended up into landfills in 2012. The pressure of reducing disposing into landfills is greatly increased by the forthcoming landfill ban on biodegradable waste in Finland. There is a need to discuss the need for increasing the utilization of biodegradable waste in regional renewable energy production to utilize the waste in a way that allows the best possibilities to reduce GHG emissions. The objectives of the thesis are: (1) to find important factors affecting renewable energy recovery possibilities from biodegradable waste, (2) to determine the main factors affecting the GHG balance of biogas production system and how to improve it and (3) to find ways to define energy performance of biogas production systems and what affects it. According to the thesis, the most important factors affecting the regional renewable energy possibilities from biodegradable waste are: the amount of available feedstock, properties of feedstock, selected utilization technologies, demand of energy and material products and the economic situation of utilizing the feedstocks. The biogas production by anaerobic digestion was seen as the main technology for utilizing biodegradable waste in agriculturally dense areas. The main reason for this is that manure was seen as the main feedstock, and it can be best utilized with anaerobic digestion, which can produce renewable energy while maintaining the spreading of nutrients on arable land. Biogas plants should be located close to the heat demand that would be enough to receive the produced heat also in the summer months and located close to the agricultural area where the digestate could be utilized. Another option for biogas use is to upgrade it to biomethane, which would require a location close to the natural gas grid. The most attractive masses for biogas production are municipal and industrial biodegradable waste because of gate fees the plant receives from them can provide over 80% of the income. On the other hand, directing gate fee masses for small-scale biogas plants could make dispersed biogas production more economical. In addition, the combustion of dry agricultural waste such as straw would provide a greater energy amount than utilizing them by anaerobic digestion. The complete energy performance assessment of biogas production system requires the use of more than one system boundary. These can then be used in calculating output–input ratios of biogas production, biogas plant, biogas utilization and biogas production system, which can be used to analyze different parts of the biogas production chain. At the moment, it is difficult to compare different biogas plants since there is a wide variation of definitions for energy performance of biogas production. A more consistent way of analyzing energy performance would allow comparing biogas plants with each other and other recovery systems and finding possible locations for further improvement. Both from the GHG emission balance and energy performance point of view, the energy consumption at the biogas plant was the most significant factor. Renewable energy use to fulfil the parasitic energy demand at the plant would be the most efficient way to reduce the GHG emissions at the plant. The GHG emission reductions could be increased by upgrading biogas to biomethane and displacing natural gas or petrol use in cars when compared to biogas CHP production. The emission reductions from displacing mineral fertilizers with digestate were seen less significant, and the greater N2O emissions from spreading digestate might surpass the emission reductions from displacing mineral fertilizers.

Potential and Challenges of Analog Reconfigurable Computation in Modern and Future CMOS

In this work, the feasibility of the floating-gate technology in analog computing platforms in a scaled down general-purpose CMOS technology is considered. When the technology is scaled down the performance of analog circuits tends to get worse because the process parameters are optimized for digital transistors and the scaling involves the reduction of supply voltages. Generally, the challenge in analog circuit design is that all salient design metrics such as power, area, bandwidth and accuracy are interrelated. Furthermore, poor flexibility, i.e. lack of reconfigurability, the reuse of IP etc., can be considered the most severe weakness of analog hardware. On this account, digital calibration schemes are often required for improved performance or yield enhancement, whereas high flexibility/reconfigurability can not be easily achieved. Here, it is discussed whether it is possible to work around these obstacles by using floating-gate transistors (FGTs), and analyze problems associated with the practical implementation. FGT technology is attractive because it is electrically programmable and also features a charge-based built-in non-volatile memory. Apart from being ideal for canceling the circuit non-idealities due to process variations, the FGTs can also be used as computational or adaptive elements in analog circuits. The nominal gate oxide thickness in the deep sub-micron (DSM) processes is too thin to support robust charge retention and consequently the FGT becomes leaky. In principle, non-leaky FGTs can be implemented in a scaled down process without any special masks by using “double”-oxide transistors intended for providing devices that operate with higher supply voltages than general purpose devices. However, in practice the technology scaling poses several challenges which are addressed in this thesis. To provide a sufficiently wide-ranging survey, six prototype chips with varying complexity were implemented in four different DSM process nodes and investigated from this perspective. The focus is on non-leaky FGTs, but the presented autozeroing floating-gate amplifier (AFGA) demonstrates that leaky FGTs may also find a use. The simplest test structures contain only a few transistors, whereas the most complex experimental chip is an implementation of a spiking neural network (SNN) which comprises thousands of active and passive devices. More precisely, it is a fully connected (256 FGT synapses) two-layer spiking neural network (SNN), where the adaptive properties of FGT are taken advantage of. A compact realization of Spike Timing Dependent Plasticity (STDP) within the SNN is one of the key contributions of this thesis. Finally, the considerations in this thesis extend beyond CMOS to emerging nanodevices. To this end, one promising emerging nanoscale circuit element - memristor - is reviewed and its applicability for analog processing is considered. Furthermore, it is discussed how the FGT technology can be used to prototype computation paradigms compatible with these emerging two-terminal nanoscale devices in a mature and widely available CMOS technology.

Hybridiautojen diffuusio Suomessa

Tämän Pro gradu –tutkielman tarkoitus on analysoida ja tutkia hybridiautojen diffuusiota Suomessa vuosien 2004 – 2012 aikana sekä antaa suuntaviivoja tulevaisuuden kehityksestä Suomen automarkkinoilla. Tutkielmassa analysoidaan myös sitä, minkälainen vaikutus veroperusteisilla hinnanalennuksilla voi olla hybridiauton kaltaisen tuotteen myyntimääriin. Tutkielman teoreettinen tausta koostuu innovaation diffuusion teoriasta ja aiemmista diffuusiotutkimuksista hybridiautoja koskien. Tutkielman analyysiosaa varten on kerätty aineistoa autonvalmistajilta ja Liikenteen turvallisuusvirastolta Trafilta. Tilastollisen aineiston perusteella on pystytty analysoimaan hybridiautojen myynnin kehitystä Suomessa ja erityisesti vuoden 2008 veromuutoksen vaikutusta myyntimääriin. Tutkielman tulokset puoltavat ajatusta siitä, että valtio voi halutessaan vauhdittaa ympäristöystävällisten autojen kauppaa huojentamalla niiden verokohtelua. Hybridiautojen myyntimäärät ovat vaihdelleet vuosittain ja diffuusio itsessään on myyntimäärien perusteella vielä alkutekijöissään, mutta tästä huolimatta kasvu on ollut jatkuvaa. Arviot tulevaisuuden myyntimääristä ovat vaihtelevia, joskin pienimuotoinen jatkuva kasvu on todennäköistä seuraavien vuosien aikana.

Thermal reactions of the major hydrocarbon components of biomass gasification gas

Gasification of biomass is an efficient method process to produce liquid fuels, heat and electricity. It is interesting especially for the Nordic countries, where raw material for the processes is readily available. The thermal reactions of light hydrocarbons are a major challenge for industrial applications. At elevated temperatures, light hydrocarbons react spontaneously to form higher molecular weight compounds. In this thesis, this phenomenon was studied by literature survey, experimental work and modeling effort. The literature survey revealed that the change in tar composition is likely caused by the kinetic entropy. The role of the surface material is deemed to be an important factor in the reactivity of the system. The experimental results were in accordance with previous publications on the subject. The novelty of the experimental work lies in the used time interval for measurements combined with an industrially relevant temperature interval. The aspects which are covered in the modeling include screening of possible numerical approaches, testing of optimization methods and kinetic modelling. No significant numerical issues were observed, so the used calculation routines are adequate for the task. Evolutionary algorithms gave a better performance combined with better fit than the conventional iterative methods such as Simplex and Levenberg-Marquardt methods. Three models were fitted on experimental data. The LLNL model was used as a reference model to which two other models were compared. A compact model which included all the observed species was developed. The parameter estimation performed on that model gave slightly impaired fit to experimental data than LLNL model, but the difference was barely significant. The third tested model concentrated on the decomposition of hydrocarbons and included a theoretical description of the formation of carbon layer on the reactor walls. The fit to experimental data was extremely good. Based on the simulation results and literature findings, it is likely that the surface coverage of carbonaceous deposits is a major factor in thermal reactions.

Teollinen öljyn erotus koalesenssisuodatuksella väliaineessa

Koalesenssi on ilmiö, jossa dispergoidun faasin pisarat pyrkivät muodostamaan suurempia pisaroita kunnes erotettava faasi muodostuu. Koalesenssi tapahtuu kolmessa päävaiheessa, jotka ovat lähestyminen, kiinnittyminen ja irrotus. Lähestymiseen vaikuttavat mekanismit ovat muuan muassa sieppaus, diffuusio, törmäysvaikutus, sedimentaatio, sähköiset repul-siovoimat ja van der Waalsin voimat. Kiinnittymisvaiheessa dispergoidun faasin pisarat syrjäyttävät väliaineen nestekalvon samalla kostuttaen väliaineen pinnan. Irrotusvaiheessa pisaran hydrodynaaminen voima voittaa pisaran ja väliaineen välisen adheesiovoiman. Koalesenssin tehokkuuteen vaikuttavat useat eri parametrit kuten virtausnopeus, pedin ominaisuudet, väliaineen ominaisuudet sekä emulsion ominaisuudet. Nämä kaikki asiat tulee ottaa huomioon koalesenssisuodatuksen suunnittelussa. Koalesenssisuodatus lukeutuu syväsuodatusmenetelmiin, jotka on ollut käytössä jo yli 100 vuotta. Koalesenssisuodatusmenetelmä on tehokas menetelmä pienten pisaroiden erottami-seen. Menetelmää käytetään esimerkiksi öljyisten jätevesien puhdistuksessa. Teollisen öljyn syväsuodatuksen etuihin kuuluu muun muassa sen kompakti koko, alhaisemmat käyt-tökustannukset, korkea erotusaste, kyky erotella pienetkin pisarat sekä helppo operointi, automatisointi ja huolto. Suurin haittapuoli on kuitenkin väliaineen tukkeutuminen, joten prosessi vaatii puhdistuksen tai väliaineen uusimisen. Tämän kandidaatintyön tarkoituksena oli koota kirjallisuustyö öljyn koalesenssisuodatuk-sesta. Työssä kartoitettiin koalesenssisuodatuksen lähtökohdat, teoria, tärkeimmät teolli-suuden sovellukset sekä väliaineet.