Oil Transportation in the Gulf of Finland in 2020 and 2030

This study is part of the Minimizing risks of maritime oil transport by holistic safety strategies (MIMIC) project. The purpose of this study is to provide a current state analysis of oil transportation volumes in the Baltic Sea and to create scenarios for oil transportation in the Gulf of Finland for the years 2020 and 2030. Future scenarios and information about oil transportation will be utilized in the modelling of oil transportation risks, which will be carried out as part of the MIMIC project. Approximately 290 million tons of oil and oil products were transported in the Baltic Sea in 2009, of which 55% (160 million tons) via the Gulf of Finland. Oil transportation volumes in the Gulf of Finland have increased from 40 million to almost 160 million tonnes over the last ten years. In Russia and Estonia, oil transportation mainly consists of export transports of the Russian oil industry. In Finnish ports in the Gulf of Finland, the majority of oil traffic is concentrated to the port of Sköldvik, while the remainder mainly consists of different oil products for domestic use. Transit transports to/from Russia make up small volumes of oil transportation. The largest oil ports in the Gulf of Finland are Primorsk, Tallinn, St. Petersburg and Sköldvik. The basis for the scenarios for the years 2020 and 2030 is formed by national energy strategies, the EU`s climate and energy strategies as well other energy and transportation forecasts for the years 2020 and 2030. Three alternative scenarios were produced for both 2020 and 2030. The oil volumes are based on the expert estimates of nine specialists. The specialists gave three volumes for each scenario: the expected oil transport volumes, and the minimum and maximum volumes. Variations in the volumes between the scenarios are not large, but each scenario tends to have rather a large difference between the figures for minimum and maximum volumes. This variation between the minimum and maximum volumes ranges around 30 to 40 million tonnes depending on the scenario. On the basis of this study, no a dramatic increase in oil transportation volumes in the Gulf of Finland is to be expected. Most of the scenarios only forecasted a moderate growth in maritime oil transportation compared to the current levels. The effects of the European energy policy favouring renewable energy sources can be seen in the 2030 scenarios, in which the transported oil volumes are smaller than in the 2020 scenarios. In the Slow development 2020 scenario, oil transport volumes for 2020 are expected to be 170.6 Mt (million tonnes), in the Average development 2020 187.1 Mt and in the Strong development 2020 201.5 Mt. The corresponding oil volumes for the 2030 scenarios were 165 Mt for the Stagnating development 2030 scenario, 177.5 Mt for the Towards a greener society 2030 scenario and 169.5 Mt in the Decarbonising society 2030 scenario.

Exploration and Design of Power-Efficient Networked Many-Core Systems

Multiprocessing is a promising solution to meet the requirements of near future applications. To get full benefit from parallel processing, a manycore system needs efficient, on-chip communication architecture. Networkon- Chip (NoC) is a general purpose communication concept that offers highthroughput, reduced power consumption, and keeps complexity in check by a regular composition of basic building blocks. This thesis presents power efficient communication approaches for networked many-core systems. We address a range of issues being important for designing power-efficient manycore systems at two different levels: the network-level and the router-level. From the network-level point of view, exploiting state-of-the-art concepts such as Globally Asynchronous Locally Synchronous (GALS), Voltage/ Frequency Island (VFI), and 3D Networks-on-Chip approaches may be a solution to the excessive power consumption demanded by today’s and future many-core systems. To this end, a low-cost 3D NoC architecture, based on high-speed GALS-based vertical channels, is proposed to mitigate high peak temperatures, power densities, and area footprints of vertical interconnects in 3D ICs. To further exploit the beneficial feature of a negligible inter-layer distance of 3D ICs, we propose a novel hybridization scheme for inter-layer communication. In addition, an efficient adaptive routing algorithm is presented which enables congestion-aware and reliable communication for the hybridized NoC architecture. An integrated monitoring and management platform on top of this architecture is also developed in order to implement more scalable power optimization techniques. From the router-level perspective, four design styles for implementing power-efficient reconfigurable interfaces in VFI-based NoC systems are proposed. To enhance the utilization of virtual channel buffers and to manage their power consumption, a partial virtual channel sharing method for NoC routers is devised and implemented. Extensive experiments with synthetic and real benchmarks show significant power savings and mitigated hotspots with similar performance compared to latest NoC architectures. The thesis concludes that careful codesigned elements from different network levels enable considerable power savings for many-core systems.

Suurnopeus-turbokoneroottoreiden termodynaaminen ja mekaaninen mallinnus sekä rakenneanalyysi

Tässä väitöskirjassa tarkastellaan suurnopeustekniikan eri sovelluksissa ilmeneviä roottoreihin liittyviä rakenteellisia vaatimuksia ja haasteita. Tässä yhteydessä suurnopeustekniikalla tarkoitetaan järjestelyä, jossa sähkökone (moottori, generaattori) ja toimilaite (turbiini, kompressori, puhallin) on kytketty ilman vaihdetta suoraan mekaanisesti yhteen ja jossa yhteisen roottorin pyörimisnopeus on selvästi suurempi kuin 50/60 hertsin verkosta syötetyn kaksinapaisen vaihtovirtasähkökoneen tahtinopeus. Tyypillistä suurnopeuskoneen roottorille on suuri tehotiheys ja suuri mekaaninen kuormitus. Siksi esimerkiksi sähkökoneen jäähdytys on entistä haasteellisempaa kasvavien rautahäviöiden ja pienempien lämmönsiirtopinta-alojen vuoksi. Tämän työn tavoitteet voidaan jakaa kolmeen osaan:  Yhdistetyn sähkö- ja turbokoneen roottorin mekaanisen rakenteen tarkastelu, jonka tavoitteena on pienentää lämmönkehitystä ja tehostaa kriittisten kohtien jäähdytystä. Tähän liittyy sähkömagneettisten häviöiden keskittäminen jäähdytyksen kannalta edullisiin kohtiin  Yhdistetyn sähkö- ja turbokoneen roottorin mekaanisen rakenteen tarkastelu kriittisten ominaistaajuuksien kannalta  Yhdistetyn sähkö- ja turbokoneen roottorin mekaanisen rakenteen analysointi lujuustekniseltä kannalta. Tähän liittyvät mm. erilaiset ahdistussovitteet ja niiden säilyminen korkeilla pyörimisnopeuksilla sekä niiden roottoria jäykistävä vaikutus ja lämmön johtuminen kyseisissä liitospinnoissa. Tämän työn tieteellinen uutuusarvo on nimenomaan yhdistetyn sähkö- ja turbokoneen roottorin rakenteen analysointi ottamalla samanaikaisesti huomioon kaikki edellä mainitut näkökohdat: jäähtyminen erityisen kuumissa kohdissa, sähköisten häviöiden alentaminen ja niiden jakautuman huomioon ottaminen, roottorin jäykkyyden maksimointi, lujuusrasitusten hallinta ja rakenteen mekaaninen stabiliteetti sekä lämpöteknisten ylimenovastusten tarkastelu.

Taajuusmuuttajaohjattu kestomagneettitahtikone opetuslaboratoriokäytössä

Kestomagneettien kehittyminen on mahdollistanut sähkökoneen rakentamisen perinteisistä menetelmistä poiketen ja on samalla luonut uudenlaisia ominaisuuksia ja käyttökohteita. Erityisesti kestomagneettitahtikone (PMSM) on kasvattanut suosiota hyvän hyötysuhteen ja luotettavuuden myötä. Työssä esitellään kestomagneettitahtikonetta sen rakenteen ja toimintaperiaatteen avulla. Tarkastellaan kestomagneettien kehitystä ja tulevaisuuden näkymiä. Perehdytään myös taajuusmuuttajaan, mitä käytetään yleensä kestomagneettitahtikoneen ohjaukseen. Lisäksi esitetään taajuusmuuttajan erilaisia säätötapoja. Työn kokeellisessa osuudessa yliopiston opetuslaboratorioon kehitetään koneikko, jonka avulla tutkitaan kestomagneettitahtikoneen toimintaan osana sähkökäyttöä. Työn tavoitteena on selvittää PMSM:n ominaisuuksia sekä suunnitella sähkötekniikan työkurssille soveltuva mittaussarja, mikä johdattaa opiskelijat tässä työssä käsiteltyihin aihealueisiin.

Kestomagneettitahtigeneraattorin kannattavuustarkastelu vesivoimalaitoksen saneerauksen yhteydessä

Työssä vertaillaan kestomagneettitahtigeneraattorin kannattavuutta suhteessa perinteiseen erillismagnetoituun tahtigeneraattoriin. Sähkön markkinahinnan nousu tulevaisuudessa, pakottaa etsimään uusia ratkaisuja jo olemassa olevien vesivoimalaitosten hyötysuhteen parantamiseksi. Hyötysuhteeseen vaikuttavat laitoksen mekaaniset ja sähköiset häviöt. Työn kohteena olevan vesivoimalaitoksen saneeraus on ajankohtainen lähivuosina, ja samalla avautuu mahdollisuus vaihtaa myös vanha erillismagnetoitu tahtigeneraattori uudempaan kestomagneeteilla toteutettuun. Työssä tarkastellaan kalliimman investoinnin kannattavuutta suhteessa kasvavaan energian tuotantoon. Tarkastelujaksolla lisääntyneen vuosituotannon osuuden rahallista arvoa verrataan investointihetken kustannuksiin. Työn edetessä havaittiin, että virtaamamäärän lisäyksellä on vahva rooli kannattavuutta laskettaessa. Pienillä virtaamilla ei saavuteta riittävää tuottoa ilman mekaanisen hyötysuhteen parantamista. Pelkästään generaattorityypin vaihto ei tällä hetkellä kannata, kun nykyisellä generaattorilla on käyttöaikaa jäljellä kymmeniä vuosia. Tilanne voi muuttua kannattavaksi esimerkiksi äkillisen generaattorivaurion myötä.

The Role of a firm’s mindset in international success - case study of Finnish marine industry firms

This thesis investigates the influence of a firm’s mindset on international success in the context of the Finnish marine industry. The study draws theoretical wisdom from organisational behaviour and strategic management literatures. The research aim set for this study was to identify and categorise existing strategic types based on mindsets found in the marine industry SMEs, and to link the influence of mindsets with success by examining the role of mindsets in a firm’s performance. Mindsets of firms were conceptualised as aggregate collections of perceptions that influence how the surrounding environment is discerned by the members of the firm. Mindsets are idiosyncratic to firms and therefore important firm-specific resources which influence decision-making and can be observed through the strategic behaviour of firms. Qualitative case study method was applied which was further supported by quantitative data on the financial performance of the ten case firms. Taxonomy based on the dimension of mindsets and prediction was developed to demonstrate four ideal types of firms identified within the marine industry. It was found that all of the case firms emphasised adaptation in their strategy while planning was emphasised to a varying degree. Moreover, two different methods of adapting were found; proactive and reactive. Firms which plan in the long-term and adapt proactively constantly investigate whether their plans are synchronous with the realities of the market; by having an open mindset, a firm’s perception of the reality of the market is enabling the firm to develop value creating strategies which are superiorly informed.This finding was supported by the financial data and led to the proposition that having an open mindset and placing a high level of emphasis on prediction may have a positive influence on international success. Also, it was proposed that concentrating only on exploiting business opportunities in the present time and not exploring any addition opportunities can have a negative influence on the firm’s performance, even if the mindset of the firm is open.

Five Baltic Ports Togehter: Forecasts, Trends and Recommendations

The ports of Stockholm, Tallinn, Helsinki, Naantali and Turku play key roles in making the Central Baltic region accessible. Effective, competitive, eco-friendly and safe port procedures and solutions for the transportation of goods are of major importance for trade in the Baltic Sea region. This report presents the most essential results and recommendations of the PENTA project, which focused on how ports could better comprehend and face current and future challenges facing carriage of goods by sea. Each of the four work packages (WPs) of the PENTA project analysed the changes from a different perspective. WP2 focused on traffic flows between the PENTA ports. Its main emphasis was on the ports, shipowners, and logistics companies that are the key parties in freight transport and on the changes affecting the economy of those ports. In WP3 noise as an environmental challenge for ports was investigated and the analysis also shed light on the relationship between the port and the city. In WP4 procedures related to safety, security and administrative procedures were researched. The main emphasis was on identifying the requirements for the harmonisation of those procedures. Collaboration is highlighted throughout this report. In order to prepare for the future, it was found that ports need to respond to growing competition, increasing costs and shifts in customer demand by strengthening their existing partnerships with other actors in the maritime cluster. Cargo and passenger transport are the main sources of income for most ports. Cargo traffic between the PENTA ports is expected to grow steadily in the future and the outlook for passenger traffic is positive. However, to prepare for the future, ports should not only secure the core activities which generate revenue but also seek alternative ways to make profit. In order to gain more transit traffic, it is suggested that ports conduct a more thorough study of the future requirements for doing business with Russia. The investigation of noise at ports revealed two specific dilemmas that ports cannot solve alone. Firstly, the noise made by vessels and, secondly, the relationship between the port and the surrounding city. Vessels are the most important single noise source in the PENTA ports and also one of the hardest noise sources to handle. Nevertheless, port authorities in Finland and Sweden are held responsible for all noise in the port area, including noise produced by vessels, which is noise the port authority can only influence indirectly. Building housing by waterfront areas close to ports may also initiate disagreements because inhabitants may want quiet areas, whereas port activities always produce some noise from their traffic. The qualitative aspects of the noise question, cooperating with the stakeholders and the communicating of issues related to noise are just as important. We propose that ports should follow the logic of continuous improvement in their noise management. The administrative barriers discussed in this report are mainly caused by differences in international and national legislation, variations in the customs procedures of each country, the incompatibility of the IT systems used in maritime transport, noncompliance with regulations regarding dangerous goods, and difficulties in applying Schengen regulations to vessels from non-EU countries. Improving the situation is out of the hands of the ports to do alone and requires joint action on a variety of levels, including the EU, national authorities and across administrative borders.

Kestomagneettitahtikonekäyttöjen erot

Permanent magnet drives with nominal power over 10 kW were not a cost-sufficient system 25 years ago due to high material expenses. The improvements in motor drives, the rise in competition and the tightening of standards and regulations have caused that the PM-drives are more and more common in the over 10 kW nominal power range. The goal of this thesis is to research the performance in relation to nominal power of a PM-drive technique that is vastly increasing its popularity in fan related devices. The studied motor technique brushless direct current drive (BLDC) consists of a voltage source inverter, permanent motor and six-step-control. The reference drive is a brushless alternating current drive (BLAC) which consists of a VSI, PM and a hysteresis control. As a conclusion there are no major obstacles that would impede the BLDC-drive technique from expanding to larger power stages. The following factors must be taken into consideration when designing a BLDC-drive: motor’s current change rate, inverter switching frequency, motor’s nominal electric frequency, phase inductance and the current handling capability of the inverter. The fluctuating material costs create instability to the end prices of PM-motors that can in the worst case lead to diminished interest towards BLDC- and PM-drives in general.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.

Modal testing and numerical modeling of the dynamic properties of layered sheet-steel structure

Recently, due to the increasing total construction and transportation cost and difficulties associated with handling massive structural components or assemblies, there has been increasing financial pressure to reduce structural weight. Furthermore, advances in material technology coupled with continuing advances in design tools and techniques have encouraged engineers to vary and combine materials, offering new opportunities to reduce the weight of mechanical structures. These new lower mass systems, however, are more susceptible to inherent imbalances, a weakness that can result in higher shock and harmonic resonances which leads to poor structural dynamic performances. The objective of this thesis is the modeling of layered sheet steel elements, to accurately predict dynamic performance. During the development of the layered sheet steel model, the numerical modeling approach, the Finite Element Analysis and the Experimental Modal Analysis are applied in building a modal model of the layered sheet steel elements. Furthermore, in view of getting a better understanding of the dynamic behavior of layered sheet steel, several binding methods have been studied to understand and demonstrate how a binding method affects the dynamic behavior of layered sheet steel elements when compared to single homogeneous steel plate. Based on the developed layered sheet steel model, the dynamic behavior of a lightweight wheel structure to be used as the structure for the stator of an outer rotor Direct-Drive Permanent Magnet Synchronous Generator designed for high-power wind turbines is studied.

Application of Carbon Nanotubes in Rotating Electrical Machines

Demand for increased energy efficiency has put an immense need for novel energy efficient systems. Electrical machines are considered as a much matured technology. Further improvement in this technology needs of finding new material to incorporate in electrical machines. Progress of carbon nanotubes research over the latest decade can open a new horizon in this aspect. Commonly known as ‘magic material’, carbon nanotubes (CNTs) have promising material properties that can change considerably the course of electrical machine design. It is believed that winding material based on carbon nanotubes create the biggest hope for a giant leap of modern technology and energy efficient systems. Though carbon nanotubes (CNTs) have shown amazing properties theoretically and practically during the latest 20 years, to the best knowledge of the author, no research has been carried out to find the future possibilities of utilizing carbon nanotubes as conductors in rotating electrical machines. In this thesis, the possibilities of utilizing carbon nanotubes in electrical machines have been studied. The design changes of electrical machine upon using carbon nanotubes instead of copper have been discussed vividly. A roadmap for this carbon nanotube winding machine has been discussed from synthesis, manufacturing and operational points of view.

Kestomagneettitahtikoneen vääntömomentin tuottokyvyn optimointi hybridibussikäyttöön

Työssä tarkastellaan hybridi- ja sähköajoneuvojen voimankäyttöjärjestelmiä ja bussin ajomoottorina toimivan kestomagneettitahtikoneen toimintaa ja sen soveltuvuutta ajoneuvokäyttöön. Esitetään analyyttinen työkalu kestomagneettitahtikoneen induktanssisuunnittelun ja koneen vääntömomentin tuottokyvyn optimoinnin tueksi. Työkalua hyödynnetään esitettävässä ajomoottorin mitoituslaskelmassa. Työssä päätellään, että kestomagneettitahtimoottori soveltuu hyvin ajoneuvokäyttöön. Maksimaalisen vääntömomentin saavuttamiseksi sen roottorin rakenne ja induktanssit on optimoitava. Analysoimalla ajoneuvokäyttöön tarkoitettua kestomagneettitahtimoottoria työkalun avulla havaitaan, että yhtä suuremmalla induktanssisuhteella vääntömomentti on pienempi kentänheikennyksessä kuin ajettaessa konetta taajuusmuuttajalla vakioteholla nimelliskuormalla. Vastaavasti yhtä pienemmillä induktanssisuhteilla vääntömomentti on pienempi kentänheikennyksessä. Todetaan, että vääntömomentti kasvaa induktanssisuhteen poiketessa yhdestä. Suuri vääntömomentti saadaan pienillä induktanssisuhteilla. Induktanssisuhteen kasvattaminen yhdestä ei lisää moottorin tuottamaa vääntömomenttia yhtä paljon kuin induktanssisuhteen pienentäminen. Työn lopuksi verrataan työkalun laskemia tuloksia kirjallisuudesta löytyvillä yhtälöillä laskettuihin tuloksiin. Työkalun laskemat tulokset vaikuttavat ristiriidattomilta ja yhteneväisiltä teorian kanssa. Työkalun toteutuksessa tehdyt teoreettiset yksinkertaistukset aiheuttavat todennäköisesti epätarkkuutta tuloksissa erityisesti suurella kuormituksella.

Gender effects on esophageal motility

It has been suggested that there are no gender effects on esophageal motility. However, in previous studies the subjects did not perform multiple swallows and the quantitative features of esophageal contractions were not evaluated. In order to investigate the gender effects on esophageal motility we studied 40 healthy normal volunteers, 20 men aged 37 ± 15 years (mean ± SD), and 20 women aged 38 ± 14 years. We used the manometric method with an eight-lumen polyvinyl catheter and continuous perfusion. The upper and lower esophageal sphincter pressures were measured by the rapid pull-through method. With the catheter positioned with one lumen opening in the lower esophageal sphincter, and the others at 5, 10 and 15 cm above the sphincter, ten swallows of a 5-ml water bolus alternated with ten dry swallows were performed. Statistical analysis was done by the Student t-test and Mann-Whitney test. Gender differences (P<0.05) were observed for wet swallows in the duration of contractions 5 cm above the lower esophageal sphincter (men: 3.7 ± 0.2 s, women: 4.5 ± 0.3 s, mean ± SEM), and in the velocity of contractions from 15 to 10 cm above the lower esophageal sphincter (men: 4.7 ± 0.3 cm/s, women: 3.5 ± 0.2 cm/s). There was no difference (P>0.05) in sphincter pressure, duration and percentage of complete lower esophageal sphincter relaxation, amplitude of contractions, or in the number of failed, multipeaked and synchronous contractions. We conclude that gender may cause some differences in esophageal motility which, though of no clinical significance, should be taken into consideration when interpreting esophageal motility tests.

The quality control of glycoprotein folding in the endoplasmic reticulum, a trip from trypanosomes to mammals

The present review deals with the stages of synthesis and processing of asparagine-linked oligosaccharides occurring in the lumen of the endoplasmic reticulum and their relationship to the acquisition by glycoproteins of their proper tertiary structures. Special emphasis is placed on reactions taking place in trypanosomatid protozoa since their study has allowed the detection of the transient glucosylation of glycoproteins catalyzed by UDP-Glc:glycoprotein glucosyltransferase and glucosidase II. The former enzyme has the unique property of covalently tagging improperly folded conformations by catalyzing the formation of protein-linked Glc1Man7GlcNAc2, Glc1Man8GlcNac2 and Glc1Man9GlcNAc2 from the unglucosylated proteins. Glucosyltransferase is a soluble protein of the endoplasmic reticulum that recognizes protein domains exposed in denatured but not in native conformations (probably hydrophobic amino acids) and the innermost N-acetylglucosamine unit that is hidden from macromolecular probes in most native glycoproteins. In vivo, the glucose units are removed by glucosidase II. The influence of oligosaccharides in glycoprotein folding is reviewed as well as the participation of endoplasmic reticulum chaperones (calnexin and calreticulin) that recognize monoglucosylated species in the same process. A model for the quality control of glycoprotein folding in the endoplasmic reticulum, i.e., the mechanism by which cells recognize the tertiary structure of glycoproteins and only allow transit to the Golgi apparatus of properly folded species, is discussed. The main elements of this control are calnexin and calreticulin as retaining components, the UDP-Glc:glycoprotein glucosyltransferase as a sensor of tertiary structures and glucosidase II as the releasing agent.

Decreased gastric emptying and gastrointestinal and intestinal transits of liquid after complete spinal cord transection in awake rats

We studied the effect of complete spinal cord transection (SCT) on gastric emptying (GE) and on gastrointestinal (GI) and intestinal transits of liquid in awake rats using the phenol red method. Male Wistar rats (N = 65) weighing 180-200 g were fasted for 24 h and complete SCT was performed between C7 and T1 vertebrae after a careful midline dorsal incision. GE and GI and intestinal transits were measured 15 min, 6 h or 24 h after recovery from anesthesia. A test meal (0.5 mg/ml phenol red in 5% glucose solution) was administered intragastrically (1.5 ml) and the animals were sacrificed by an iv thiopental overdose 10 min later to evaluate GE and GI transit. For intestinal transit measurements, 1 ml of the test meal was administered into the proximal duodenum through a cannula inserted into a gastric fistula. GE was inhibited (P<0.05) by 34.3, 23.4 and 22.7%, respectively, at 15 min, 6 h and 24 h after SCT. GI transit was inhibited (P<0.05) by 42.5, 19.8 and 18.4%, respectively, at 15 min, 6 h and 24 h after SCT. Intestinal transit was also inhibited (P<0.05) by 48.8, 47.2 and 40.1%, respectively, at 15 min, 6 h and 24 h after SCT. Mean arterial pressure was significantly decreased (P<0.05) by 48.5, 46.8 and 41.5%, respectively, at 15 min, 6 h and 24 h after SCT. In summary, our report describes a decreased GE and GI and intestinal transits in awake rats within the first 24 h after high SCT.