Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Fracture modes and acoustic emission characteristics of hydrogen-assisted cracking in high-strength low-alloy steel weldment

The aim of the present paper is to study the relationship between the fracture modes in hydrogen-assisted cracking (HAC) in microalloied steel and the emission of acoustic signals during the fracturing process. For this reason, a flux-cored arc weld (FCAW) was used in a high-strength low-alloy steel. The consumable used were the commercially available AWS E120T5-K4 and had a diameter of 1.6 mm. Two different shielding gases were used (CO2 and CO2+5% H2) to obtain complete phenomenon characterization. The implant test was applied with three levels of restriction stresses. An acoustic emission measurement system (AEMS) was coupled to the implant test apparatus. The output signal from the acoustic emission sensor was passed through an electronic amplifier and processed by a root mean square (RMS) voltage converter. Fracture surfaces were examined by scanning electron microscopy (SEM) and image analysis. Fracture modes were related with the intensity, the energy and the number of the peaks of the acoustic emission signal. The shielding gas CO2+5% H2 proved to be very useful in the experiments. Basically, three different fracture modes were identified in terms of fracture appearance: microvoid coalescence (MVC), intergranular (IG) and quasi-cleavage (QC). The results show that each mode of fracture presents a characteristic acoustic signal.

Power-line-communication-based data transmission concept for an LVDC electricity distribution network – Analysis and implementation

Communications play a key role in modern smart grids. New functionalities that make the grids ‘smart’ require the communication network to function properly. Data transmission between intelligent electric devices (IEDs) in the rectifier and the customer-end inverters (CEIs) used for power conversion is also required in the smart grid concept of the low-voltage direct current (LVDC) distribution network. Smart grid applications, such as smart metering, demand side management (DSM), and grid protection applied with communications are all installed in the LVDC system. Thus, besides remote connection to the databases of the grid operators, a local communication network in the LVDC network is needed. One solution applied to implement the communication medium in power distribution grids is power line communication (PLC). There are power cables in the distribution grids, and hence, they may be applied as a communication channel for the distribution-level data. This doctoral thesis proposes an IP-based high-frequency (HF) band PLC data transmission concept for the LVDC network. A general method to implement the Ethernet-based PLC concept between the public distribution rectifier and the customerend inverters in the LVDC grid is introduced. Low-voltage cables are studied as the communication channel in the frequency band of 100 kHz–30 MHz. The communication channel characteristics and the noise in the channel are described. All individual components in the channel are presented in detail, and a channel model, comprising models for each channel component is developed and verified by measurements. The channel noise is also studied by measurements. Theoretical signalto- noise ratio (SNR) and channel capacity analyses and practical data transmission tests are carried out to evaluate the applicability of the PLC concept against the requirements set by the smart grid applications in the LVDC system. The main results concerning the applicability of the PLC concept and its limitations are presented, and suggestion for future research proposed.

The consequences of e-HRM on line managers

The purpose of this research was to provide a deeper insight into the consequences of electronic human resource management (e-HRM) for line managers. The consequences are viewed as used information system (IS) potentials pertaining to the moderate voluntaristic category of consequences. Due to the need to contextualize the research and draw on line managers’ personal experiences, a qualitative approach in a case study setting was selected. The empirical part of the research is loosely based on literature on HRM and e-HRM and it was conducted in an industrial private sector company. In this thesis, method triangulation was utilized, as nine semi-structured interviews, conducted in a European setting, created the main method for data collection and analysis. Other complementary data such as HRM documentation and statistics of e-HRM system usage were utilized as background information to help to put the results into context. E-HRM has partly been taken into use in the case study company. Line managers tend to use e-HRM when a particular task requires it, but they are not familiar with all the features and possibilities which e-HRM has to offer. The advantages of e-HRM are in line with the company’s goals. The advantages are e.g. an transparency of data, process consistency, and having an efficient and easy-to-use tool at one’s disposal. However, several unintended, even contradictory, and mainly negative outcomes can also be identified, such as over-complicated processes, in-security in use of the tool, and the lack of co-operation with HR professionals. The use of e-HRM and managers’ perceptions regarding e-HRM affect the way in which managers perceive the consequences of e-HRM on their work. Overall, the consequences of e-HRM are divergent, even contradictory. The managers who considered e-HRM mostly beneficial to their work found that e-HRM affects their work by providing information and increasing efficiency. Those managers who mostly perceived challenges in e-HRM did not think that e-HRM had affected their role or their work. Even though the perceptions regarding e-HRM and its consequences might reflect the strategies, the distribution of work, and the ways of working in all HRM in general and can’t be generalized as such, this research contributed to the field of e-HRM and it provides new perspectives to e-HRM in the case study organization and in the academic field in general.

Differentiation of Metabolically Distinct Areas within Head and Neck Region using Dynamic 18F-FDG Positron Emission Tomography Imaging

Positron Emission Tomography (PET) using ¹⁸F-FDG is playing a vital role in the diagnosis and treatment planning of cancer. However, the most widely used radiotracer, ¹⁸F-FDG, is not specific for tumours and can also accumulate in inflammatory lesions as well as normal physiologically active tissues making diagnosis and treatment planning complicated for the physicians. Malignant, inflammatory and normal tissues are known to have different pathways for glucose metabolism which could possibly be evident from different characteristics of the time activity curves from a dynamic PET acquisition protocol. Therefore, we aimed to develop new image analysis methods, for PET scans of the head and neck region, which could differentiate between inflammation, tumour and normal tissues using this functional information within these radiotracer uptake areas. We developed different dynamic features from the time activity curves of voxels in these areas and compared them with the widely used static parameter, SUV, using Gaussian Mixture Model algorithm as well as K-means algorithm in order to assess their effectiveness in discriminating metabolically different areas. Moreover, we also correlated dynamic features with other clinical metrics obtained independently of PET imaging. The results show that some of the developed features can prove to be useful in differentiating tumour tissues from inflammatory regions and some dynamic features also provide positive correlations with clinical metrics. If these proposed methods are further explored then they can prove to be useful in reducing false positive tumour detections and developing real world applications for tumour diagnosis and contouring.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T- 10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 17−20 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 50−80 KIAS (∼90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Stars and Strings für Jazzensemble u. Streichorchester

Soitinnus: jazzyhtye, jousiorkesteri.

Biopolttoaineiden on-line -laadunmittauksen hyödyt energiantuotannossa

Biopolttoaineet ovat tärkeä energianlähde suomalaisessa energiantuotannossa. Biopoltto- aineille on kuitenkin ominaista laadun vaihtelevuus. Yksi tärkeimmistä laatutekijöistä on kosteus, joka vaikuttaa myös polttoaineen energiasisältöön. Laatutekijät puolestaan vai- kuttavat polttoainekäsittelyyn, polttoprosessiin ja koko laitoksen hyötysuhteeseen. Tämän työn tarkoituksena oli tutkia voisiko biopolttoaineiden online-laadunmittaus tuoda lisäarvoa energiantuotantolaitokselle. Esimerkkinä käytettiin yhtä online-laadunmittaus- sovellusta, InrayFuel-röntgenmittausjärjestelmää. Sillä voidaan seurata biopolttoaineiden kosteutta ja polttoaineen sisältämiä vierasaineita. Työssä on laadittu kustannusanalyysi, jolla pyritään selvittämään, onko nykyisen kertaluontoisen mittausmenetelmän korvaami- nen jatkuvatoimisella kannattavaa. Esimerkkilaitoksena on Etelä-Savon Energian Pur- sialan voimalaitos, jossa röntgenmittausjärjestelmään on testattu. Saatujen tulosten mukaan investoiminen esimerkkimittausjärjestelmään maksaisi itsensä takaisin alle vuodessa. Kun laitoksella pystytään seuraamaan polttoaineen laatua jatkuva- toimisesti, laadunhallinta paranee ja sitä kautta voidaan saavuttaa kustannussäästöjä. Polt- toaineesta johtuvat häiriötilanteet vähenevät, polttoaine on mahdollista optimoida edulli- semmaksi polton kannalta ja poltto-olosuhteita voidaan säätää paremmin, jolloin päästöt vähenevät ja hyötysuhde kasvaa. Työssä käytetty laskenta analysoi kuitenkin hyvin ylei- sellä tasolla, sillä käytössä ei ollut laitoksen omaa taselaskentajärjestelmää. Laskenta siis sisältää paljon oletuksia. Tämän ja rohkaisevien tulosten vuoksi tutkimusta jatkuvatoimi- sen laadunmittauksen hyödyistä kannattaa tehdä enemmän.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

Software product line for power converters

Työn tilaajana toimi Visedo Oy. Työn tavoitteina oli tutkia Visedo Oy:n ohjelmistokehityksen nykytila, tunnistaa seuraavat parannuskohteet ja antaa ohjeita havaittujen parannuskohteiden korjaamiseksi. Visedo Oy:n tehonmuokkain ohjelmistokehityksen nykytilaa käsiteltiin neljän valitun osa-alueen näkökulmasta: ohjelmistoarkkitehtuurityyli, komponenttipohjainen ohjelmistokehitys, ohjelmistotuotelinjojen kehitysmenetelmät ja ohjelmistovariaatioiden hallinta. Valituilla osa-alueilla havaittujen parannuskohteiden perusteella annettiin korjausehdotuksia: ohjelmistoarkkitehtuurin rakenteeseen, komponenttien jakautumiselle, komponenttien koostamiselle ja komponenttien versioinnille. Lisäksi ehdotettiin uudenlaista ohjelmistotuotelinja rakennetta, joka yhdistää kerros- ja komponenttipohjaiset arkkitehtuurityylit mahdollistaen ominaisuuksiltaan eroavien tehonmuokkain ohjelmistojen hallinnan.

Sellutehtaan TRS-hajapäästöjen hallinta

Diplomityön tavoitteena on selvittää TRS-hajapäästöjen muodostumista sekä päästöjen määrää UPM Kymmene Oyj:n Kaukaan sellu- ja paperitehtaalla. Työssä laaditaan TRS-hajapäästöjen mittausohjelma, minkä päivitetty massa- ja paperiteollisuuden BAT-vertailuasiakirja vaatii. Mittausohjelma täydentää tehdasintegraatin ilmapäästöjen valvontaohjelmaa. Hajapäästöjen lisäksi tavoitteena on selvittää häiriötilanteiden aiheuttamia TRS-päästömääriä. Kirjallisuusosassa selvitetään hajujen muodostumista sellun ja paperin valmistuksessa ja niiden käsittelyä ympäristövaikutusten minimoimiseksi. Lisäksi esitellään mittausmenetelmiä. Kokeellisessa osassa valituista kohteista mitataan TRS-pitoisuudet ja hajukaasujen virtaama, joiden perusteella lasketaan TRS-kuormitus. Kuormitus suhteutetaan sellutonnille. Osa kohteista on hajapäästökohteita ja osa kohteita, joista hajukaasut häiriötilanteissa johdetaan käsittelemättä ulos. Tulosten perusteella TRS-hajapäästöjä muodostuu sellun valmistuksessa noin 0,04 kgS/ADt ja jätevedenkäsittelyssä, pääasiassa lietteenkäsittelyssä 0,04 kgS/ADt. Hajapäästöjä syntyy eniten kohteissa, missä keräily on toteutettu kevyemmin tai sitä ei ole. Merkittävimmät kohteet Kaukaalla ovat lietteenkäsittely, koivukuitulinja ja mäntyöljylaitos. Havulinjan ja talteenotto-osaston hajapäästöt ovat muita osastoja vähäisemmät. Yhteensä sellutehtaan ja lietteenkäsittelyn TRS-hajapäästömäärä on 0,08 kgS/ADt, mikä on BAT vaihteluvälin (0,05-0,2 kgS/ADt) sisällä. TRS-häiriöpäästöjen osuus tehtaan TRS päästöistä voi häiriötilanteiden toistuessa nousta merkittäviksi. Tähän vaikuttaa merkittävästi häiriintyvä kohde.

A mutant cell line partially responsive to both IFN-a and IFN-g

A recessive mutant cell line, B7, which is partially responsive to both interferon (IFN)- a and IFN-g is described. B7 was FACS sorted from a cellular pool, which was obtained from the parental cell line 2C4, after several rounds of mutagenesis. The partial responsiveness to IFN was observed both in terms of expression of cell surface markers (CD2, class I and II HLAs) and mRNA expression of IFN-stimulated genes (9-27; 6-16; 2'-5' OAS; GBP and HLA-DRa). A genetic cross with the U4 mutant (JAK1-, a member of the Janus family of nonreceptor tyrosine kinase) did not restore full IFN-responsiveness to B7, and JAK1 cDNA transfection into B7 restored the wild phenotype of the cell line, defining B7 as a member of the U4 complementation group. Nevertheless, JAK1 mRNA was not detected in this mutant. Transcriptional regulator complexes such as IRF1/2 (IFN-regulatory factor) and ISGF3-g (IFN-stimulated gene factor) were constitutively formed in the B7 mutant and co-migrated with the IFN-induced complexes expressed in the parental cell line 2C4. Thus, this cell line seems to be useful for understanding cis-acting elements governing JAK1 mRNA expression.

Potential for Greenhouse Gas Emission Reductions by Using Biomethane as a Road Transportation Fuel

The aim of this thesis is to study whether the use of biomethane as a transportation fuel is reasonable from climate change perspective. In order to identify potentials and challenges for the reduction of greenhouse gas (GHG) emissions, this dissertation focuses on GHG emission comparisons, on feasibility studies and on the effects of various calculation methodologies. The GHG emissions calculations are carried out by using life cycle assessment (LCA) methodologies. The aim of these LCA studies is to figure out the key parameters affecting the GHG emission saving potential of biomethane production and use and to give recommendations related to methodological choices. The feasibility studies are also carried out from the life cycle perspective by dividing the biomethane production chain for various operators along the life cycle of biomethane in order to recognize economic bottlenecks. Biomethane use in the transportation sector leads to GHG emission reductions compared to fossil transportation fuels in most cases. In addition, electricity and heat production from landfill gas, biogas or biomethane leads to GHG reductions as well. Electricity production for electric vehicles is also a potential route to direct biogas or biomethane energy to transportation sector. However, various factors along the life cycle of biomethane affect the GHG reduction potentials. Furthermore, the methodological selections have significant effects on the results. From economic perspective, there are factors related to different operators along the life cycle of biomethane, which are not encouraging biomethane use in the transportation sector. To minimize the greenhouse gas emissions from the life cycle of biomethane, waste feedstock should be preferred. In addition, energy consumption, methane leakages, digestate utilization and the current use of feedstock or biogas are also key factors. To increase the use of biomethane in the transportation sector, political steering is needed to improve the feasibility for the operators. From methodological perspective, it is important to recognize the aim of the life cycle assessment study. The life cycle assessment studies can be divided into two categories: 1.) To produce average GHG information of biomethane to evaluate the acceptability of biomethane use compared to fossil transportation fuels. 2.) To produce GHG information of biomethane related to actual decision-making situations. This helps to figure out the actual GHG emission changes in cases when feedstock, biogas or biomethane are already in other use. For example directing biogas from electricity production to transportation use does not necessarily lead to additional GHG emission reductions. The use of biomethane seems to have a lot of potential for the reduction of greenhouse gas emissions as a transportation fuel. However, there are various aspects related to production processes, to the current use of feedstock or biogas and to the feasibility that have to be taken into account.

Cloning and characterization of Echinococcus granulosus (Cestode) EgactI and EgactII actin gene promoters and their functional analysis in the NIH3T3 mouse cell line

We report here for the first time the structure and function of a promoter from a cestode. The ability of DNA fragments respectively encompassing the 935-bp and 524-bp regions upstream from the ATG codon from the EgactI and EgactII actin genes of Echinococcus granulosus to promote transcription was studied in the NIH3T3 mouse cell line. The results of transfection assays showed that both regions have strong promoter activity in these cells. The fragments were tested in both orientations and the 524-bp fragment of EgactII presented a bidirectional promoter activity. Deletion analysis of EgactI and EgactII promoters indicated the presence of regulatory regions containing putative silencer elements. These results indicate that both EgactI and EgactII promoters are functional and that the preliminary functional evaluation of E. granulosus and possibly of other cestode promoters can be performed in heterologous cell lines.