Post-steam-treatment of Mo/HZSM-5 catalysts: An alternative and effective approach for enhancing their catalytic performances of methane dehydroaromatization

Post-steam-treatment is a facile and effective method for improving the catalytic performances of Mo/HZSM-5 catalysts in methane dehydroaromatization under nonoxidative conditions. The treatment can enhance the stability of the catalyst and also give a higher methane conversion and a higher yield of light aromatics, as well as a decrease in the formation rate of carbonaceous deposits. (27)Al, (29)Si, and (1)H multinuclear magic angle spinning nuclear magnetic resonance, X-ray photoelectron spectroscopy, X-ray diffraction, X-ray fluorescence spectroscopy, and thermogravimetric analysis measurements as well as catalytic reaction evaluations were employed to conduct comparative studies on the properties of the catalysts before and after the post-steam-treatment. The results revealed that the number of free Bronsted acid sites per unit cell decreased, while more Mo species migrated into the HZSM-5 channels for the 6Mo/HZSM-5 catalysts after the post-steam-treatment. In addition, the average pore diameter was also larger for the post-steam-treated catalysts, and this was advantageous for mass transport of the reaction products. However, a severe post-steam-treatment, i.e., with longer treating time, of the 6Mo/HZSM-5 catalyst will lead to the formation of the Al(2)(MoO(4))(3) phases, which is detrimental to the reaction.

Towards manipulation of post-biosynthetic events in secondary metabolism of plant cell cultures

Plant cell cultures have been suggested as a feasible technology for the production of a myriad of plant-derived metabolites. However, commercial application of plant cell culture has met limited success with only a handful of metabolites produced at the pilot- and commercial-scales. To improve the production of secondary metabolites in plant cell cultures, efforts have been devoted predominantly to the optimization of biosynthetic pathways by both process and genetic engineering approaches. Given that secondary metabolism includes-the synthesis. metabolism and catabolism of endogenous compounds by the specialized proteins, this review intends to draw attention to the manipulation and optimization of post-biosynthetic events that follow the formation of core metabolite structures in biosynthetic pathways. These post-biosynthetic events-the chemical and enzymatic modifications, transport, storage/secretion and catabolism/degradation have been largely unexplored in the past. Potential areas are identified where further research is needed to answer fundamental questions that have implications for advanced bioprocess design. Anthocyanin production by plant cell cultures is used as a case study for this discussion, as it presents a good example of compounds for which there are extensive research publications but still no commercial bioprocess. It is perceived that research on post-biosynthetic processes may lead to future opportunities for significant advances in commercial plant cell cultures. (C) 2002 Elsevier Science Inc. All rights reserved.

一种Post-WIMP界面：PGIS的实现

随着计算机应用从桌面环境扩展到移动环境，计算机用户从专业化走向大 众化，传统的 WIMP界面的缺点逐渐体现出来。笔式用户界面作为 Post-WIMP 界面的一种重要形式，具有自然、和谐的交互特性，成为当前研究的热点之一。 针对这一方向，本文对笔式用户界面范式展开了研究。首先，本文阐述了一种 新的基于笔交互的界面范式 PGIS，定义了纸、小工具等交互组件，以及各种组 件的显示形态及交互形式。然后，实现了 PGIS 界面，包括交互对象的管理、 显示等内容。最后，详细介绍了 PGIS 界面的使用过程，并用一个应用实例加 以验证。为了支持上层应用程序的可移植性和可维护性，PGIS界面的使用采用 了模型驱动构架的开发思想。目前，我们基于 PGIS 界面开发了几款优秀的笔 式交互软件，如幼儿教学系统、便签本系统、篮球战术板系统等。这些系统完 全满足用户对笔交互应用程序的需求，目前可在 Linux 系统、Windows 系统等 多种系统上运行。PGIS界面范式的可行性也因此得到了很好的验证。 本文的主要内容有以下几点： 1. 阐述了一种 Post-WIMP范畴下的新的界面范式：PGIS。 本文在对Post-WIMP界面做了充分地理解和分析的基础上，阐述了一种新 的界面范式：PGIS。这是一种基于笔交互的界面范式，文中对该范式的纸笔隐 喻方式、所包含的内容、各交互组件的表现形式、以及各组件间的静态及动态 关系做出了详细的描述。 2. 实现了PGIS界面。 为了验证PGIS界面范式的可行性，并直接支持基于 PGIS范式的应用程序 开发，本文详细介绍了PGIS界面的实现细节，其中包括PGIS界面中所包含的 元素、PGIS界面中交互对象的显示、交互对象的管理、以及交互对象对基本原 语的转换和响应。 3. 介绍了 PGIS界面的使用过程。 整个使用过程采用模型驱动架构的思想，引入对以下三个子模块的调用： 与平台相关的底层核心库和 PGIS 引擎、与平台无关的场景设计工具。这三个 子模块决定了上层应用程序的可移植性和可维护性。另外，场景设计工具提供 了代码自动生成的功能，大幅度缩短了应用程序的开发周期。 4. 实现了一个基于 PGIS界面的幼儿教学系统。 为了说明 PGIS界面的使用流程，本文设计并实现了一个基于PGIS界面的 幼儿教学系统。在开发过程中，大部分工作在场景设计工具中快速完成，小部 分工具集中在数据管理库、场景任务库的开发上。该系统的评估结果很好地验 证了 PGIS界面范式的可行性。

Large current gain and low operational voltage permeable metal-base organic transistors based on Au/Al double layer metal base

In order to realize the common-emitter characteristics of the tris(8-hydroxyquinoline) aluminium (Alq(3))-based organic transistors, we used Au/Al double metal layer as the base, thus the vertical metal-base transistors with structure of Al/n-Si/Au/Al/Alq(3)/LiF/Al were constructed. It was found that the contact properties between the base and the organic semiconductors play an important role in the device performance. The utilization of Au/Al double layer metal base allows the devices to operate at high gain in the common-emitter and common-base mode at low operational voltage.

High gain in hybrid transistors with BAlq(3)/Alq(3) isotype heterostructure emitter

We report the fabrication of permeable metal-base transistors based on bis(2-methyl-8-quinolinolato-N1,O8)-(1,1'-biphenyl-4-olato) aluminum (BAlq(3))/tri(8-hydroxyquinoline) aluminum (Alq(3)) isotype heterostructure as emitter layer. In this transistor, n-Si was used as the collector, LiF/Al as the emitter electrode, and Au/Al bilayer metal as the base. We show that the leakage current is greatly reduced in Al/n-Si/Au/Al/BAlq(3)/Alq(3)/LiF/Al devices with respect to Al/n-Si/Au/Al/Alq(3)/LiF/Al devices due to the utilization of BAlq(3)/Alq(3) isotype heterostructure emitter, leading to high common-base and common-emitter current gains at low driving voltages.

Hybrid permeable metal-base transistor with large common-emitter current gain and low operational voltage

We demonstrate the suitability of N,N'-diphenyl-N,N'-bis(1-naphthylphenyl)-1,1'-biphenyl-4,4'-diamine (NPB), an organic semiconductor widely used in organic light-emitting diodes (OLEDs), for high-gain, low operational voltage nanostructured vertical-architecture transistors, which operate as permeable-base transistors. By introducing vanadium oxide (V2O5) between the injecting metal and NPB layer at the transistor emitter, we reduced the emitter operational voltage.

Enhancement of stability of polymer light-emitting diodes by post annealing

We investigate the effect of thermal annealing before and after cathode deposition on the stability of polymer light-emitting diodes (PLEDs) based on green fluorescent polyfluorene derivative. The annealed PLEDs exhibit improved charge transport and red-shift emission compared to the as-fabricated device. The stability of the PLEDs is largely enhanced by post-annealing before and after Ca deposition, which is attributed to the enhanced charge transport and the intimate contact between the cathode and the emissive layer.

High gain in hybrid transistors with vanadium oxide/tris(8-hydroxyquinoline) aluminum emitter

We report the electrical characterization of hybrid permeable-base transistors with tris(8-hydroxyquinoline) aluminum as emitter layer. These transistors were constructed presenting an Al/n-Si/Au/Alq(3)/V2O5/Al structure. We investigate the influence of the V2O5 layer thickness and demonstrate that these devices present high common-base and common-emitter current gain, and can be operated at very low driving voltages, lower than 1 V, in both, common-base and common-emitter modes.

Amplified spontaneous emission and gain from optically pumped films of dye-doped polymers

The amplified spontaneous emission and gain characteristics of various fluorescent dyes, 2-(1,1-dimethylethyl)-6(2-(2,3,6,7-tetrahydro-1,1,7,7-tetramethyl-1H,5H-benzo[ij] quinolizin-9-1)ethenyl)-4H-pyran-4-ylidene) propanedinitrile (DCJTB) and 4-dicyanomethylene-2-methyl-6-(p-dimethyl-aminostyryl)-4H-pyran (DCM), doped in polystyrene (PS) matrices were studied and compared. It was found that DCJTB has a larger net gain, 40.72 cm(-1), a lower loss, 2.49 cm(-1), and a lower threshold, 0.16 (mJ/pulse)/cm(2), than DCM, which has a net gain of 11.95 cm(-1), a loss of 9.25 cm(-1), and a threshold of 4(mJ/pulse)/cm(2). The improvement of performance in DCJTB PS films is attributed to the larger free volume of DCJTB caused by the introduction of steric spacer groups into the DCJTB molecule.

Preparation and characterization of post-derivatives from functional polystyrene (ATRP) with p-nitroaniline-azomethine phenol and their thermal and optical study

The functional polystyrene, (Cl-PS)(2)-CHCOOCH2CH2OH ( designated as XPSt and coded P2) was prepared by ATRP at 130(0)C using CuCl and bipyridine as catalysts, 2,2-dichloro acetate-ethylene glycol (DCAG) as multifunctional initiator and THF as solvent. 4-Nitoroaniline azomethine-4' phenol (P1) as chromophores were covalently linked to the functional end groups of the polymer by using simple displacement reaction. The functional polystyrenes, namely XPSt (P2) and (PS)(2)-CHCOOCH2CH2OH, designated as X-PSt and coded P3 and their post-derivatives, namely, DXPSt (P4) and DX-PSt (P5) respectively were characterized by IR, NMR and UV spectroscopies, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), polarising optical microscopy (POM) and XRD studies. DSC showed that incorporation of chromophores in the side chains of polymers towards the polystyrene moiety increases the rigidity of the polymer and subsequently, its glass transition temperature; however the incorporation of side chain towards the alcoholic functional group decreases the glass transition temperature. The post derivatives do not play any significant role to increase the thermal stability ( TGA).

Polymerized unsymmetrical iron post-metallocene catalyst for ethylene polymerization

The unsymmetrical allyl containing post-metallocene complex [ArN = C( Me)] [(ArN)-N-' = C(Me)]C5H3NFeCl2 [Ar = 2,6(i- Pr)(2)C6H3, Ar' = 4-allyl-2,6-(i-Pr)(2)C6H3] (3) has been prepared and characterized. Complex (3) can be co-polymerized with styrene in the presence of radical initiator to produce polymerized post-metallocene catalyst which exhibits high activity for ethylene polymerization (2.5 x 10(6) g PE/mol Fe.h).

Allyl containing iron post-metallocene catalyst for ethylene polymerization

Tridentate ligand[(2,6-ArN=C(Me))(2)C5H3N](Ar=4-allyl-2,6-(i-Pr)(2)C6H3)(4)which contains allyl groups on each aryl ring was ready prepared and reacted with FeCl2. 4H(2)O to give the precatalyst [(2,6-ArN=C(CH3))(2)C5H3N]. FeCl2 (5). Compounds 2-5 were characterized by H-1 NMR, EI-MS,and IR. The complex 5 which was actived by methylaluminoxane(MAO) exhibits high activity for ethylene polymerization [1.9 x 10(6) g pE.(mol Fe . h)(-1) at 0 degreesC]. It was showed that the activity was decreased with increasing temperature and the polymer product was highly linear PE with (M) over bar (eta) varying from 50000 to 260000.

Exploration of post radiation effects on polyamide-1010

Irradiated polyamide-1010 (PA1010) with and without heat treatment after gamma-ray irradiation was compared by wide angle x-ray diffraction (WAXD), differential scanning calorimeter (DSC) and the determination of gel fractions. The results indicate that post radiation effects due to post radiation crosslinking and scissions affect physical properties. Post radiation effects restrain the formation and perfection of the planes (010), and make the crystals imperfect. Post radiation effects change the crystalline structures of polyamide-1010.