Caracterização de cerâmicas porosas de alumina reforçada com zircônia produzidas pelo método da réplica

Porous ceramics have many applications: thermal insulation, catalytic support, materials to fire protection, filters, and others. There are many techniques to production of ceramic filters. One technique to obtain ceramic filters is the replication method. This method consists in the impregnation of polymeric foam with ceramic slurry followed by a heating treatment that will burn out the organic elements and sintering of the material, resulting of a replication of the original foam. To perform their functions ceramic filters must satisfy mechanical requirements and permeability parameters (darcian k1 and no-darcian k2). The permeability and the strength of the ceramic material are dependent of the pore size and pore distribution. To the use at high temperatures the evaluation of mechanical properties in these temperatures is necessary. In this work the mechanical behavior of two commercial porous ceramics (10 and 40 poros per inch) was studied these materials were submitted to compression and four-point flexure test (room temperature, at 1000 °C, after thermal shock). Density and porosity measurements, permeability tests and microstructural analysis by scanning electronic microscopy (SEM) were realized. The Results showed that the decrease of mechanical strength of these materials, when submitted to thermal shock, occur for propagation of new cracks from cracks pre-existing and the permeability depends of the pore size

Análise do comportamento mecânico de espumas cerâmicas a base de alumina obtidas pelo método da réplica

Ceramics with porous cellular structure, called ceramic foams, have a potential use in several applications, such as: thermal insulation, catalyst supports, filters, and others. Among these techniques to obtain porous ceramics the replication method is an important process. This method consists of impregnation of a sponge (usually polymer) with ceramic slurry, followed by a heat treatment, which will happen the decomposition of organic material and sintering the ceramic material, resulting in a ceramic structure which is a replica of impregnated sponge. Knowledge of the mechanical properties of these ceramics is important for these materials can be used commercially. Gibson and Ashby developed a mathematical model to describe the mechanical behavior of cellular solids. This model wasn´t for describing the ceramics behavior produced by the replica method, because it doesn´t consider the defects from this type of processing. In this study were researched mechanical behavior of porous alumina ceramics obtained by the replica method and proposed modifications to the model of Gibson and Ashby to accommodate this material. The polymer sponge used in processing was characterized by thermogravimetric analysis and scanning electron microscopy. The materials obtained after sintering were characterized by mechanical strength tests on 4-point bending and compression, density and porosity and by scanning electron microscopy. From these results it was evaluated the mechanical strength behavior compared to Gibson and Ashby model for solid cellular structure and was proposed a correction of this model through a factor related to struts integrity degree, which consider fissures present in the structure of these materials besides defects geometry within the struts

Método de Otimização Topológica em Estruturas Tridimensionais

The topology optimization problem characterize and determine the optimum distribution of material into the domain. In other words, after the definition of the boundary conditions in a pre-established domain, the problem is how to distribute the material to solve the minimization problem. The objective of this work is to propose a competitive formulation for optimum structural topologies determination in 3D problems and able to provide high-resolution layouts. The procedure combines the Galerkin Finite Elements Method with the optimization method, looking for the best material distribution along the fixed domain of project. The layout topology optimization method is based on the material approach, proposed by Bendsoe & Kikuchi (1988), and considers a homogenized constitutive equation that depends only on the relative density of the material. The finite element used for the approach is a four nodes tetrahedron with a selective integration scheme, which interpolate not only the components of the displacement field but also the relative density field. The proposed procedure consists in the solution of a sequence of layout optimization problems applied to compliance minimization problems and mass minimization problems under local stress constraint. The microstructure used in this procedure was the SIMP (Solid Isotropic Material with Penalty). The approach reduces considerably the computational cost, showing to be efficient and robust. The results provided a well defined structural layout, with a sharpness distribution of the material and a boundary condition definition. The layout quality was proporcional to the medium size of the element and a considerable reduction of the project variables was observed due to the tetrahedrycal element

Simulação numérica da interação entre uma nuvem incidente de vórtices e uma aerofólio através do método dos vórtices

The study of aerodynamic loading variations has many engineering applications, including helicopter rotor blades, wind turbines and turbo machinery. This work uses a Vortex Method to make a lagrangian description of the a twodimensional airfoil/ incident wake vortex interaction. The flow is incompressible, newtonian, homogeneus and the Reynolds Number is 5x105 .The airfoil is a NACA 0018 placed a angle of attack of the 0° and 5°simulates with the Painel Method with a constant density vorticity panels and a generation poit is near the painel. The protector layer is created does not permit vortex inside the body. The vortex Lamb convection is realized with the Euler Method (first order) and Adans-Bashforth (second order). The Random Walk Method is used to simulate the diffusion. The circular wake has 366 vortex all over positive or negative vorticity located at different heights with respect to the airfoil chord. The Lift was calculated based in the algorithm created by Ricci (2002). This simulation uses a ready algorithm vatidated with single body does not have a incident wake. The results are compared with a experimental work The comparasion concludes that the experimental results has a good agrement with this papper

Método rápido de extração de DNA de bactérias

Desenvolveu-se um método rápido para extração de DNA de bactérias, que ao contrário de outros métodos, não requer o uso de enzimas, como lisozima e proteinase K, previamente, utilizado-se o carbonato de silício (carborundum) como agente físico para efetuar a quebrar da parede celular da bactéria. Com este método conseguiu-se extrair DNA bacteriano num menor tempo, além de mais rápido, ele mostrou-se mais simples e econômico, quando comparado aos métodos convencionais. O DNA obtido pode ser utilizado para diversas finalidades relacionadas ao DNA de bactérias, obtendo-se uma quantidade razoável de DNA, que varia de 725 µg/mL a 1170 µg/mL por cada 0,1 g de célula bacteriana, com ótima qualidade.

Método de preparo das sementes de mamoneira (Ricinus communis L.) para o teste de tetrazólio

O teste de tetrazólio é um método rápido e eficaz para avaliar a viabilidade e o vigor de sementes. O presente trabalho teve por objetivo padronizar o método de preparo das sementes de mamoneira (Ricinus communis L.) para a avaliação do potencial fisiológico pelo teste de tetrazólio. Foram testados os seguintes métodos de preparo das sementes: corte longitudinal mediano através do tegumento, endosperma e embrião; corte longitudinal diagonal sem atingir o eixo embrionário; remoção do tegumento; remoção do tegumento com corte longitudinal mediano através do endosperma e embrião; e remoção do tegumento com corte longitudinal mediano, paralelo aos cotilédones, através do endosperma e embrião. Antes dos preparos, as sementes foram pré-condicionadas entre papel toalha umedecido por 18 horas a 30ºC, e após os preparos, as sementes foram imersas na solução de tetrazólio na concentração de 0,5% e mantidas em câmara escura a 35ºC para o desenvolvimento da coloração. Avaliou-se a uniformidade da coloração das sementes após cada preparo, por meio da comparação entre eles. Para a avaliação do potencial fisiológico das sementes de mamoneira pelo teste de tetrazólio o método indicado de preparo é a remoção do tegumento, com posterior corte longitudinal e mediano, no sentido do comprimento, através do endosperma e embrião.

Atividade radicular da soja: definição de um método

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Produtividade de amendoim em função da calagem e do método de secagem

Estudar o efeito da calagem e do método de secagem na produtividade do amendoim (Arachis hypogea L., cv. Botutatu) foi o objetivo deste trabalho, conduzido num solo Latossolo Vermelho-Escuro, textura média, em São Manuel, São Paulo. Os tratamentos consistiram de ausência ou presença de calagem (2,05 Mg ha-1) e secagem à sombra, ao sol e duas formas combinadas desta última com estufa. A calagem eliminou a fitotoxicidade de manganês, melhorando a nodulação e a nutrição nitrogenada, que, conseqüentemente, levaram ao aumento do número de ramificações, de vagens por planta e da produtividade. Com a calagem, observou-se também redução nas perdas durante a colheita. Das formas de secagem, a realizada à sombra e a combinada campo-estufa foram as que proporcionaram maiores produtividades, por permitirem melhor maturação dos frutos e menores perdas na colheita.

Preservação do inóculo de Plasmodiophora brassicae utilizando o método de congelamento

A preservação das estruturas de resistência de Plasmodiophora brassicae, em condições laboratoriais, é dificultada pelo fato de se tratar de um parasita obrigatório. O método de congelamento, utilizando freezer, comum foi testado com o objetivo de viabilizar a sobrevivência e a preservação de suas características infectivas. Raízes de diferentes brássicas, naturalmente infectadas por P. brassicae, contendo sintomas típicos de hérnia, de uma mesma propriedade localizada no município de Pardinho, Estado de São Paulo, foram coletadas em diferentes épocas e imediatamente congeladas, em freezer, a aproximadamente -20ºC. Os tratamentos foram divididos da seguinte maneira: T1: hérnias congeladas por 389 dias (rúcula); T2: hérnias congeladas por 242 dias (brócolis); T3: hérnias congeladas por 21 dias (couve chinesa) e T4: testemunha (sem inóculo). Os testes de patogenicidade, após diferentes períodos de armazenamento, foram realizados em condições de casa de vegetação (25±2ºC). Cada planta de uma variedade suscetível de couve-chinesa (Pak choi) foi inoculada com 2mL da suspensão de esporos de cada tratamento, na concentração de 10(7) esporos.mL-1. Cada tratamento contou com seis repetições distribuídas em blocos ao acaso. Passadas cinco semanas após a inoculação, as raízes das plantas foram lavadas e avaliadas. Houve diferença significativa entre os tratamentos. Os materiais congelados, entre 21 a 242 dias preservaram suas características infectivas, mostrando que o método de congelamento em freezer, nesse período, pode ser uma boa opção para a preservação das estruturas de resistência deste patógeno.

Método não destrutivo de estimativa da área foliar de plantas daninhas de ambiente aquático: tanner-grass e capim-fino

The continuous inputs from agriculture areas and human or industrial sewer have been provided a widely demographic explosion of tropical tanner-grass and para grasss plants in the rivers and water reservoirs of Brazil. Considering the importance of these noxious weeds there is a vast necessity of basic studies on aspects related to reproduction, growing, development, nutritional requirements, responses to control systems and others. In most studies, leaf area knowledge is crucial and it is one of the most difficult characteristics to be measured because it usually requires expensive equipments or it uses a destructive technique. The objective of this work was to develop equations for leaf blade dimensional parameters to allow determination of the leaf area of African tanner-grass (Brachiaria subquadripara (Trin.) Hitchc) and para grass (Brachiaria mutica (Forsk.) Stapf.). Correlations between real leaf area and dimensional parameters of leaf blade such as length along the main vein (L) and maximum width (W) perpendicular to the main axis were studied. Only the linear equations allowed a good leaf area estimate. It is suggested to opt for a simple linear equation involving respective products of length times maximum width considering linear coefficient equal to zero. Thus, B. subquadripara (SS) and B. mutica (SM) non destructive leaf blade area estimates may be performed by the following formulas: SS = 0.7719 (L x W) and SM = 0.7479 (L x W), with coefficients of determination (R(2)) of 0.9594 and 0.9408, respectively.

Desidratação de polpas de frutas pelo método foam-mat

This study aimed to investigate the foam mat drying process of pineapple and mango pulp, as well as to evaluate the final product quality. Initially, the selection of fruit and additives was conducted based on density and stability determinations of mango, seriguela, umbu and pineapple foams. After selecting pineapple and mango for further studies, the fruit pulps and fruit foams were characterized in regard to their physicochemical composition. The temperature (60oC or 70oC) and the foam thickness (4 and 11 mm) were evaluated in accordance to the obtained drying curves and after model adjustment. Mango and pineapple powders obtained at the best process conditions were characterized in regard to their physicochemical composition, solubility, reconstitution time. Yoghurts were prepared with the addition of pineapple and mango powders and they were evaluated for their sensory acceptance. Results show that the best drying rates were achieved by using 70o C and layers 4mm thick for both fruits. The Page model successfully fitted the drying experimental data and it can be used as a predictive model. Pineapple and mango powders showed acid pH, high soluble solids content, low water activity (approx. 0.25), lipids between 1.46% and 2.03%, protein around 2.00%, and ascorbic acid content of 17,73 mg/100g and 14.32 mg/100g, for mango and pineapple, respectively. It was observed higher ascorbic acid retention for pineapple and mango powders processed at 70o C, which would be explained by the lower drying time applied. The fruit powders exhibited high solubility and fast reconstitution in water. The sensory acceptance indexes for yoghurts with the addition of both fruit powders were higher than 70%, which reflect the satisfactory product acceptance

Caracterização morfológica e microestrutural da perovskita BaCexPr1-xO3 sintetizada a partir do método de complexação combinando EDTA/Citrato

In this study, binary perovskite (BaCexO3) were doped with praseodymium (Pr) to obtainment of the ternary material BaCexPr1-xO3. This material was synthesized by the complexation method combining EDTA/Citrate with the stoichiometric ratio of the element Praseodymium ranging from x = 0.1 to x = 0.9 in order to determine the influence of this rare earth element on the morphology and microstructure of the final powder. At first the material was synthesized based on the route proposed by literature (Santos, 2010), and then characterized by SEM and XRD, besides being refined by the Rietveld method. In the material that had lowest residual parameter, S, and lowest average size of crystal, pH variation of synthesis solution was made in order to identify the influence of this parameter on the morphology and microscopy of the final powder. The results show that addition of praseodymium did not directly influence the crystallographic and lattice parameters, keeping even the same orthorhombic structure of the binary material BaCexO3, according to Yamanaka et al (2003). Material type BaCe0,2Pr0,8O3 had lowest residual parameter (S=1.4) and lowest average size of crystallite (26.4 nm), being used as reference in the pH variation of synthesis solution for 9, 7, 5 and 3, respectively. Variation of this parameter showed that when the synthesis solution pH was decreased to below 11, there was an increase in the average size of crystals, for pH 9, about 58.3%, for pH 7 (30.3 %), for pH 2 (2.3%) and for pH 3 (42%), indicating that the value initially used and quoted by Santos (2010) was the most coherent

Obtenção de ferrita de cobalto através de dois métodos de síntese: método de complexação combinando EDTA/Citrato e método hidrotérmico

In this work it was synthesized and characterized the cobalt ferrite (CoFe2O4) by two methods: complexation combining EDTA/Citrate and hydrothermal investigating the influence of the synthesis conditions on phase formation and on the crystallite size. The powders were mainly characterized by x-ray diffraction. In specific cases, it was also used scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), x-ray fluorescence (XRF) and isotherms of adsorption and desorption of nitrogen (BET method). The study of the crystallite size was based on the interpretation of x-ray diffractograms obtained and estimated by the method of Halder-Wagner-Scherrer and Langford. An experimental design was made in order to assist in quantifying the influence of synthesis conditions on the response variables. The synthesis parameters evaluated in this study were: pH of the reaction medium (8, 9 and 10), the calcination temperature (combined complexation method EDTA/Citrate 600°C, 800°C and 1000°C), synthesis temperature (hydrothermal method 120°C, 140°C and 160°C), calcination time (combined complexation method EDTA/Citrate - 2, 4 and 6 hours) and time of synthesis (hydrothermal method 6, 15 and 24 hours). By the hydrothermal method was possible to produce mesoporous powders with high purity, with an average crystallite size up to 7 nm, with a surface area of 113.44 m²/g in the form of pellets with irregular morphology. By using the method of combined complexation EDTA/Citrate, mesoporous powders were produced with greater purity, crystallite size up to 22nm and 27.95 m²/g of surface area in the form of pellets with a regular morphology of plaques. In the experimental design was found that the hydrothermal method to all the studied parameters (pH, temperature and time) have significant effect on the crystallite size, while to the combined complexation method EDTA/Citrate, only temperature and time were significant

Modelagem de distorções entre sad 69 e sirgas 2000 pelo método de shepard e grades regulares

Brazil follows the tendency of some countries to update and/or review their fundamental geodetic network. The adoption of geocentric referentials like SIRGAS 2000, the new official reference system of the Geodetic Brazilian System has been an advance. Changes in referential implies in coordinates changes on the network stations as well as the network geometry. To make use of analogical and digital products which are already known in the old referentials are necessary approaches to the coordinate conversion, which minimize the distortions between the used reference frames. This paper presents a distortion modeling approach between reference frames, based on distortion grid generation by using the Shepard's method. To analyze the approach some experiments were performed with the generation of a 1 degrees x1 degrees distortion grid to model the distortions between SAD 69 (1996) and SIRGAS (2000) frames. The results in the test stations were promising, with an average reduction of 50% in the RMS coordinates after the distortions modeling.

Método monoscópico para a determinação automática da altura de edifícios em fotografias aéreas

This paper proposes a monoscopic method for automatic determination of building's heights in digital photographs areas, based on radial displacement of points in the plan image and geometry at the time the photo is obtained. Determination of the buildings' heights can be used to model the surface in urban areas, urban planning and management, among others. The proposed methodology employs a set of steps to detect arranged radially from the system of photogrammetric coordinates, which characterizes the lateral edges of buildings present in the photo. In a first stage is performed the reduction of the searching area through detection of shadows projected by buildings, generating sub-images of the areas around each of the detected shadow. Then, for each sub-image, the edges are automatically extracted, and tests of consistency are applied for it in order to be characterized as segments of straight arranged radially. Next, with the lateral edges selected and the knowledge of the flight height, the buildings' heights can be calculated. The experimental results obtained with real images showed that the proposed approach is suitable to perform the automatic identification of the buildings height in digital images.