High level stable expression of rat brain type IIA sodium channel ?-subunit in CHO cells

The neuronal sodium channels are responsible for the rising phase of action potential and are composed of three subunits, of which the alpha-subunit has been shown to be adequate for most of its functional properties. We have stably expressed the rat brain type IIA sodium channel alpha-subunit in CHO cell tine using a CMV promoter-based vector. The expression was confirmed by detecting a 6.5 kb RNA corresponding to sodium channel alpha-subunit using Northern hybridization. The cells stably expressing the alpha-subunit, yield isolated sodium currents of amplitudes greater than 4nA when studied in whole-cell configuration of the patch-clamp technique. The sodium currents are characterized by activation and inactivation properties similar to neuronal sodium channels, and are blocked by the voltage gated sodium channel blocker tetrodotoxin (TTX).

High On-Off Ratio Bilayer Graphene Complementary Field Effect Transistors

In this paper, we propose a novel S/D engineering for dual-gated Bilayer Graphene (BLG) Field Effect Transistor (FET) using doped semiconductors (with a bandgap) as source and drain to obtain unipolar complementary transistors. To simulate the device, a self-consistent Non-Equilibrium Green's Function (NEGF) solver has been developed and validated against published experimental data. Using the simulator, we predict an on-off ratio in excess of 10(4) and a subthreshold slope of similar to 110mV/decade with excellent scalability and current saturation, for a 20nm gate length unipolar BLG FET. However, the performance of the proposed device is found to be strongly dependent on the S/D series resistance effect. The obtained results show significant improvements over existing reports, marking an important step towards bilayer graphene logic devices.

Phase separation in critical and off-critical fluids: specific experimental behaviours at criticality

The phase separation in fluids close to a critical point can be observed in the form of either an interconnected pattern (critical case) or a disconnected pattern (off-critical case). These two regimes have been investigated in different ways. First, a sharp change in pattern is shown to occur very close to the critical point when the composition is varied. No crossover has been observed between the t1 behaviour (interconnected) and a t1/3 behaviour (disconnected), where t is time. This latter growth law, which occurs in the case of compact droplets, will be discussed. Second, it has been observed that a growing interconnected pattern leaves a signature in the form of small droplets. The origin of such a distribution will be discussed in terms of coalescence of domains. No distribution of this kind is observed in the off-critical case.

Propagating intensity disturbances in polar corona as seen from AIA/SDO

Context. Polar corona is often explored to find the energy source for the acceleration of the fast solar wind. Earlier observations show omni-presence of quasi-periodic disturbances, traveling outward, which is believed to be caused by the ubiquitous presence of outward propagating waves. These waves, mostly of compressional type, might provide the additional momentum and heat required for the fast solar wind acceleration. It has been conjectured that these disturbances are not due to waves but high speed plasma outflows, which are difficult to distinguish using the current available techniques. Aims. With the unprecedented high spatial and temporal resolution of AIA/SDO, we search for these quasi-periodic disturbances in both plume and interplume regions of the polar corona. We investigate their nature of propagation and search for a plausible interpretation. We also aim to study their multi-thermal nature by using three different coronal passbands of AIA. Methods. We chose several clean plume and interplume structures and studied the time evolution of specific channels by making artificial slits along them. Taking the average across the slits, space-time maps are constructed and then filtration techniques are applied to amplify the low-amplitude oscillations. To suppress the effect of fainter jets, we chose wider slits than usual. Results. In almost all the locations chosen, in both plume and interplume regions we find the presence of propagating quasi-periodic disturbances, of periodicities ranging from 10-30 min. These are clearly seen in two channels and in a few cases out to very large distances (approximate to 250 `') off-limb, almost to the edge of the AIA field of view. The propagation speeds are in the range of 100-170 km s(-1). The average speeds are different for different passbands and higher in interplume regions. Conclusions. Propagating disturbances are observed, even after removing the effects of jets and are insensitive to changes in slit width. This indicates that a coherent mechanism is involved. In addition, the observed propagation speed varies between the different passpands, implying that these quasi-periodic intensity disturbances are possibly due to magneto-acoustic waves. The propagation speeds in interplume region are higher than in the plume region.

Reactivity and catalytic activity of layered YBA2CU3O7-delta (123) type defect perovskites

The chemical modifications of structure, reactivity and catalytic properties of layered triple perovskite oxides, related to the YBa2Cu3O7-delta (123) system, have been briefly reviewed. These oxides form a versatile family of materials with wide-ranging chemical and physical properties. The multiple sites available for chemical doping, and the ability to reversibly intercalate oxygen at the defect sites have rendered these oxides important model systems in the area of oxide catalysis. An attempt has been made to comprehend the hitherto known catalytic reactions and correlate them to various factors like structure, oxygen diffusional limitations, different geometries adopted by various substituents, oxidative non-stoichiometry and activation energy for oxygen desorption. In particular, results on the enhanced catalytic activity of cobalt-substituted 123 oxide systems towards the selective catalytic oxidation of ammonia to nitric oxide and carbon monoxide to carbon dioxide are presented.

Flexural bond strength of masonry using various blocks and mortars

This paper deals with an experimental study on flexural bond strength of masonry using various blocks in combination with different mortars. Flexural bond strength of masonry has been determined by testing stack-bonded prisms using a modified bond wrench test set-up. The effect of mortar composition and strength on the masonry's. flexural bond strength using three types of masonry units (stabilized mud blocks, stabilized soil-sand blocks and burnt brick) has been examined. The effect of the masonry unit's moisture content on flexural bond strength has also been studied. Increases in mortar strength lead to increased flexural bond strength for cement mortar, irrespective of the type of masonry unit. It has been found that combination mortars, such as soil-cement mortar and cement-lime mortar, lead to better bond strength compared to cement mortars. The moisture content of the masonry unit at the time of casting has displayed significant influence on the flexural bond strength of the masonry. It has been found that for each type of masonry unit, an optimum moisture content exists, beyond which the flexural bond strength falls off quickly.

Coadsorption of Dioxygen and Water on the Ni(110) Surface: Role of O1--Type Species in the Dissociation of Water

While the adsorption of dioxygen at a clean Ni(110) surface gives rise to two O(1s) features at 531 and 530 eV assigned to O-(a) and O2-(a) type species respectively, coadsorption of dioxygen and water mixtures result in the additional formation of hydroxyl species characterized by an O(1s) peak at 532.3 eV. The latter is attributed to the oxygen induced dissociation of water via a low energy pathway involving the O-(a)-type species. The proportions of the O-(a) and the hydroxyl species are greater for small O-2/H2O ratios and lower temperatures (120 K). With increase in temperature, the relative surface concentrations of the O-(a) and the hydroxyl species decrease while there is an increase in the concentration of the oxidic O2-(a) species. Thus, the surface concentrations of both the hydroxyl and the O2-(a) species depend critically on the presence of O- type species. Above 300K the surface chemistry in the main involves the conversion of O- to O2- species via the hydroxyl species.

Influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304 during hot working

The influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304L, 304 and 304 as-cast, during hot working has been studied. Compression and torsion tests were conducted in the temperature range 1100 to 1250 degrees C and strain rate range 0.001 to 100 s(-1) on these materials, Ferrite formation occurs during deformation at temperatures above 1150 degrees C and strain rates above 10 s(-1), in stainless steel type AISI 304L and 304. The tendency for the formation of ferrite is more in as-cast 304 than in wrought 304, In as-cast 304 the ferrite forms at lower temperatures and strain rates, The tendency for the ferrite formation is more in torsion than in compression.

Tandem 5-exo-trig allyl and 3-exo-trig radical cyclisation and rearrangement to copa and ylanga type sesquiterpene skeleton

A novel tandem 5-exo-trig allyl and 3-exo-trig radical cyclisation and rearrangement to copa and ylanga type sesquiterpene skeleton is reported.

Seebeck Coefficient in Bulk and Quantum Wells of Non-Parabolic Kane-Type Materials

We present a simplified and quantitative analysis of the Seebeck coefficient in degenerate bulk and quantum well materials whose conduction band electrons obey Kane's non-parabolic energy dispersion relation. We use k.p formalism to include the effect of the overlap function due to the band non-parabolicity in the Seebeck coefficient. We also address the key issues and the conditions in which the Seebeck coefficient in quantum wells should exhibit oscillatory dependency with the film thickness under the acoustic phonon and ionized impurity scattering. The effect of screening length in degenerate bulk and quantum wells has also been generalized for the determination of ionization scattering. The well-known expressions of the Seebeck coefficient in non-degenerate wide band gap materials for both bulk and quantum wells has been obtained as a special case and this provides an indirect proof of our generalized theoretical analysis.

Further studies on Norrish type II reactions including a reaction in the first excited singlet state and cyclization of 1:4 biradicals

The Norrish type II processes of methyl-2,2-dimethyl- cyclopropyl ketone, alpha-alkoxy acetones and alkyl pyruvates have been examined using the AM1 semi-empirical molecular orbital method with complete geometry optimization at the partial configuration interaction level in the restricted Hartree-Fock (RHF) frame. The results reveal that the methyl-substituted cyclopropyl ketone has a constrained geometry favourable for hydrogen abstraction from the gamma-position relative to the carbonyl group in the excited singlet state. The presence of the ether oxygen atom in the beta-position relative to the carbonyl group in alkoxy acetones and alkyl pyruvates leads to increased reactivity relative to alkyl monoketones and diketones respectively. The cyclization of 1:4 biradicals has been studied in the unrestricted Hartree-Fock (UHF) frame, and the results reveal that the 1:4 biradical derived from alkoxy acetones readily cyclizes to form oxetanols. On the other hand, in the 1:4 biradicals derived from methyl-substituted cyclopropyl ketone, the three-membered ring breaks readily to form an enol intermediate. Delocalization of an odd electron in 1:4 biradicals derived from alkyl pyruvates is thought to make cyclization difficult.

Optimization of cold and warm workability in stainless steel type AISI 316L using instability maps

The deformation characteristics of stainless steel type AISI 316L under compression in the temperature range 20 to 600 degrees C and strain rate range 0.001 to 100 s(-1) have been studied with a view to characterizing the flow instabilities occurring in the microstructure. At temperatures lower than 100 degrees C and strain rates higher than 0.1 s(-1), 316L stainless steel exhibits flow localization whereas dynamic strain aging (DSA) occurs at intermediate temperatures and below 1 s(-1). To avoid the above flow instabilities, cold working should be carried out at strain rates less than 0.1 s(-1). Warm working of stainless steel type AISI 316L may be done in the temperature and strain rate regime of: 300 to 400 degrees C and 0.001 s(-1) 300 to 450 degrees C and 0.01 s(-1): 450 to 600 degrees C and 0.1 s(-1); 500 degrees C and 1 s(-1) since these regions are free from flow instabilities like DSA and flow localization. The continuum criterion, developed on the basis of the principles of maximum rate of entropy production and separability of the dissipation function, predicts accurately all the above instability features.

Structured systems methodology for evaluation of random interruptions in continuous process type manufacturing systems

A structured systems methodology was developed to analyse the problems of production interruptions occurring at random intervals in continuous process type manufacturing systems. At a macro level the methodology focuses on identifying suitable investment policies to reduce interruptions of a total manufacturing system that is a combination of several process plants. An interruption-tree-based simulation model was developed for macroanalysis. At a micro level the methodology focuses on finding the effects of alternative configurations of individual process plants on the overall system performance. A Markov simulation model was developed for microlevel analysis. The methodology was tested with an industry-specific application.