Degradation and stabilisation of diisocyanate cured polybutadiene

Hydroxyl terminated polybutadiene (HTPB) has been used as a rocket propellant binder which is required to be stored for at least twenty years. It is found that the excellent stress-strain characteristics of this propellant can be totally lost, during this long storage, due to the deterioration of the polybutadiene chains. As a result, the propellant can not stand the service loads, which may lead to a catastrophe. The study of the HTPB binder degradation, below 80°C, has been carried out by investigating the environmental factors and the changes which occur along the macromolecular chains. Results have shown that oxygen is the main factor which causes the crosslinking and chain scission reactions. The former is the predominant reaction and proceeds rapidly under oxygen sufficient environment. The unsaturation of polymer chain, which provides the desired physical properties to the binder, was lost with the increase in crosslink density. At the same time hydroperoxides were found to form and decompose along the polymer chains. Therefore, the deterioration of the binder results from the oxidation of polymer chains. Since the oxidation reaction occurred at higher rate than oxygen diffusion rate and oxygen diffusion rate is inversely proportional to the crosslink density, the binder, below the surface layer in a thick section container, could be naturally protected under an oxygen deficient condition for a long time. Investigation of the effectiveness of antioxidants in HTPB binder has shown that the efficiency of an antioxidant depends on its ability to scavenge radicals. Generally, aromatic amines are the most effective binder antioxidants. But when a peroxide decomposer is combined with an aromatic amine at the appropriate ratio, a synergistic effect is obtained, which gives the lowest binder gel increase rate.

Characterization of oxide layers grown on D9 austenitic stainless steel in lead bismuth eutectic

Lead bismuth eutectic (LBE) is a possible coolant for fast reactors and targets in spallation neutron sources. Its low melting point, high evaporation point, good thermal conductivity, low reactivity, and good neutron yield make it a safe and high performance coolant in radiation environments. The disadvantage is that it is a corrosive medium for most steels and container materials. This study was performed to evaluate the corrosion behavior of the austenitic stainless steel D9 in oxygen controlled LBE. In order to predict the corrosion behavior of steel in this environment detailed analyses have to be performed on the oxide layers formed on these materials and various other relevant materials upon exposure to LBE. In this study the corrosion/oxidation of D9 stainless steel in LBE was investigated in great detail. The oxide layers formed were characterized using atomic force microscopy, magnetic force microscopy, nanoindentation, and scanning electron microscopy with wavelength-dispersive spectroscopy (WDS) to understand the corrosion and oxidation mechanisms of D9 stainless steel in contact with the LBE. What was previously believed to be a simple double oxide layer was identified here to consist of at least 4 different oxide layers. It was found that the inner most oxide layer takes over the grain structure of what used to be the bulk steel material while the outer oxide layer consists of freshly grown oxides with a columnar structure. These results lead to a descriptive model of how these oxide layers grow on this steel under the harsh environments encountered in these applications.

Horizontal deflection of single particle in a paramagnetic fluid

This paper describes the horizontal deflection behaviour of a single particle in paramagnetic fluids under a high-gradient superconducting magnetic field. A glass box was designed to carry out experiments and test assumptions. It was found that the particles were deflected away from the magnet bore centre and particles with different density and/or susceptibility settled at a certain position on the container floor due to the combined forces of gravity and magneto-Archimedes as well as lateral buoyant (displacement) force. Matlab was chosen to simulate the movement of the particle in the magnetic fluid, the simulation results were in good accordance with experimental data. The results presented here, though, are still very much in their infancy, which could potentially form the basis of a new approach to separating materials based on a combination of density and susceptibility. Graphical abstract: [Figure not available: see fulltext.] © 2014 EDP Sciences, SIF, Springer-Verlag Berlin Heidelberg.

Particle separation by horizontal deflection in paramagnetic fluid

This paper describes the horizontal deflection behaviour of the streams of particles in paramagnetic fluids under a high-gradient superconducting magnetic field, which is the continued work on the exploration of particle magneto-Archimedes levitation. Based on the previous work on the horizontal deflection of a single particle, a glass box and collector had been designed to observe the movement of particle group in paramagnetic fluids. To get the exact separation efficiency, the method of "sink-float" involved the high density fluid polytungstate (dense medium separation) and MLA (Mineral Liberation Analyser) was performed. It was found that the particles were deflected and settled at certain positions on the container floor due to the combined forces of gravity and magneto-Archimedes forces as well as a lateral buoyancy (displacement) force. Mineral particles with different densities and susceptibilities could be deflected to different positions, thus producing groups of similar types of particles. The work described here, although in its infancy, could form the basis of new approach of separating particles based on a combination of susceptibility and density. © 2014 Elsevier B.V.

File Format for Storage of Multimedia Information

AMS Subj. Classification: 68U05, 68P30

High performance liquid level monitoring system based on polymer fiber Bragg gratings embedded in silicone rubber diaphragm

Liquid-level sensing technologies have attracted great prominence, because such measurements are essential to industrial applications, such as fuel storage, flood warning and in the biochemical industry. Traditional liquid level sensors are based on electromechanical techniques; however they suffer from intrinsic safety concerns in explosive environments. In recent years, given that optical fiber sensors have lots of well-established advantages such as high accuracy, costeffectiveness, compact size, and ease of multiplexing, several optical fiber liquid level sensors have been investigated which are based on different operating principles such as side-polishing the cladding and a portion of core, using a spiral side-emitting optical fiber or using silica fiber gratings. The present work proposes a novel and highly sensitive liquid level sensor making use of polymer optical fiber Bragg gratings (POFBGs). The key elements of the system are a set of POFBGs embedded in silicone rubber diaphragms. This is a new development building on the idea of determining liquid level by measuring the pressure at the bottom of a liquid container, however it has a number of critical advantages. The system features several FBG-based pressure sensors as described above placed at different depths. Any sensor above the surface of the liquid will read the same ambient pressure. Sensors below the surface of the liquid will read pressures that increase linearly with depth. The position of the liquid surface can therefore be approximately identified as lying between the first sensor to read an above-ambient pressure and the next higher sensor. This level of precision would not in general be sufficient for most liquid level monitoring applications; however a much more precise determination of liquid level can be made by linear regression to the pressure readings from the sub-surface sensors. There are numerous advantages to this multi-sensor approach. First, the use of linear regression using multiple sensors is inherently more accurate than using a single pressure reading to estimate depth. Second, common mode temperature induced wavelength shifts in the individual sensors are automatically compensated. Thirdly, temperature induced changes in the sensor pressure sensitivity are also compensated. Fourthly, the approach provides the possibility to detect and compensate for malfunctioning sensors. Finally, the system is immune to changes in the density of the monitored fluid and even to changes in the effective force of gravity, as might be obtained in an aerospace application. The performance of an individual sensor was characterized and displays a sensitivity (54 pm/cm), enhanced by more than a factor of 2 when compared to a sensor head configuration based on a silica FBG published in the literature, resulting from the much lower elastic modulus of POF. Furthermore, the temperature/humidity behavior and measurement resolution were also studied in detail. The proposed configuration also displays a highly linear response, high resolution and good repeatability. The results suggest the new configuration can be a useful tool in many different applications, such as aircraft fuel monitoring, and biochemical and environmental sensing, where accuracy and stability are fundamental. © (2015) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

Parallel Algorithm for the Local Variations Method

Димитър С. Илиев, Станимир Д. Илиев - Актуално е изследването на поведението на течен менискус в околността на хетерогенна стена. До сега няма получено числено решение за формата на менискуса около стена, която е с хаотична хетерогенност. В настоящата статия е разработен алгоритъм за метода на локалните вариации, който може да се използва на многопроцесорни системи. С този метод е получен за първи път профила на равновесен течен менискус около вертикална стена с хаотична хетерогенност.

Editorial

Full text: There are phrases in daily use today which were not so common a decade or so back, such as ‘ageing population’ or ‘climate changes’ or ‘emerging markets’ or even ‘social networking’. How do these things affect our lives is certainly interesting but for us as eye care practitioners how these changes affect our clinical work may be also relevant and sometimes more interesting. A recent advertisement for recruitment to the Royal Marine Corps of the British Army ended with a comment ‘find us on Facebook!’ The BCLA, IACLE and other organisations as well as many manufacturers have their own Facebook groups. In 2011 Chandni Thakkar was awarded the BCLA summer studentship and her project was based around increasing the contact lens business of a small independent optometric practice where contact lens sales were minimal. The practice typically recruited one new wearer per month. Chandni was able to increase the number of new patient fits with various strategies (her work was presented as poster at the 2012 BCLA conference in Birmingham). One of her strategies was to start a Facebook group and 655 joined the special group she started in just over a month. Interestingly she found that the largest single factor in convincing patients to trial contact lenses was recommendation by the eye care practitioner at the end of the examination, but nonetheless it is interesting that so many people used the social networking site to find out more information regarding contact lenses in her study. Moreover, we already see the use, by some practitioners, of smart phone ‘apps’ or electronic diaries or text messages when coordinating patient check-ups. Climate change has affected the way we think and act; we now leave out special recycle bins and we hope that the items that are recyclable are actually recycled and do not just join our other refuse somewhere down the track! How environmentally friendly are contact lenses? This was discussed by various speakers at this year's BCLA conference in Birmingham. Daily disposable lenses surely produce more contact lens waste but do not involve solutions in plastic bottles like monthly lenses. It is certainly something that manufacturers are taking seriously and of course there are environmental benefits but the cynic in each of us sees the marketing potential too. The way the ageing population is certainly something that will impact all healthcare providers. In the case of eye care with people living longer they will need refractive corrections for longer. Furthermore, since presbyopes are not resigning themselves to only gentle hobbies like knitting and gardening, but instead want to continue playing tennis or skiing or whatever, their visual demands are becoming more complex. This is certainly an area that contact lens manufacturers are focussing on (pun not intended!). Again the BCLA conference in Birmingham saw the launch of various new products by different companies to help us deal with our presbyopic contact lens wearers. It is great to have such choice and now with fitting methods becoming easier too we have no excuse not to try them out with our clients. Finally to emerging markets – well there was not a specific session at the BCLA conference in May discussing this but this most certainly would have been discussed by professional services managers and marketing directors of most of the contact lens companies. ‘How will we conquer China?’ ‘How can we increase our market share in Russia?’ Or ‘How should we spend our marketing budget in India?’ These topics as well as others would certainly have cropped up in backroom discussions. Certainly groups like IACLE (International Association of CL Educators) have increasing numbers of members and activities in developing markets to ensure that educators educate, to that practitioners can practice successfully and in turn patients can become successful contact lenses wearers. Companies also wish to increase their market share in these developing markets and from the point of view of CLAE we are certainly seeing more papers being submitted from these parts of the world. The traditional centres of knowledge are being challenged, I suppose as they have been throughout history, and this can only be a good thing for the pursuit of science. The BCLA conference in Birmingham welcomed more international visitors than ever, and from more countries, and long may that continue. Similarly, CLAE looks forward to a wider audience in years to come and a wider network of authors too.

Capillary siphons and their application in the fuel delivery system of direct methanol fuel cells

The objective of the work is to develop a fuel delivery system for potable direct methanol fuel cell. Currently, one of the most fundamental limitations of direct methanol fuel cells is that the fuel supplied to the anode of the DMFC must be a very dilute aqueous methanol solution (usually 0.5∼1.5 M). If a DMFC is filled with a dilute aqueous methanol solution, the fuel cell operation time per refuel would be very short, which would considerably diminish the advantage of a DMFC over a conventional battery. To overcome this difficulty, a complex fuel delivery system based on the modern micro system technology was proposed by the author. The proposed fuel delivery system would include micro-pumps, a methanol sensor, and a control unit. The fuel delivery system adds considerable costs to the fuel cell system and consume considerable amount of electricity from the fuel cell, which in turn significantly reduces the net power output of the fuel cell. As a result, the DMFC would have tremendous difficulty to compete with the conventional battery technology in terms of costs and power output. ^ This work presents a novel passive fuel delivery system for direct methanol fuel cells. In this particular system, a methanol fuel and an aqueous methanol solution are stored separately in two containers and a wick is disposed between the two containers in a siphon fashion, with the container of the aqueous methanol solution communicating with the anode of the DMFC. Methanol is siphoned from the methanol container to the aqueous solution container in-situ when the methanol in the aqueous methanol solution is consumed during the operation of the fuel cell. Through a proper selection of the wick and the containers, the methanol concentration near the anode of the DMFC could be maintained within a preferable range. ^

Incursión en el espacio ontológico de las novelas “La ninfa inconstante” de Guillermo Cabrera Infante y “Todos se van” de Wendy Guerra

This thesis examines the phenomenological projection of space in two Cuban novels: La ninfa inconstante (2008) by Guillermo Cabrera Infante (1929–2005), and Todos se van (2006) by Wendy Guerra (1970–). Both novels are paradigmatic of two generations of Cuban writers who portray the city of Havana as a backdrop against which to project socio-political and biographical narratives. To problematize ethical and political omissions in the novels, this work incorporates disciplines such as philosophy, urbanism, architecture, sociology and literary theory. Through the concepts of prominent phenomenologists, such as Gaston Bachelard, Martin Heidegger and Maurice Merleau-Ponty, amongst others, this study evaluates how space becomes a construction to ambivalent dynamics of truth telling within contrasting, suffocating sociopolitical contexts. In addition, it explores how these phenomenological spaces are defined in relation to power. For instance, the Cuban Revolution, and its aftermath of more than 52 years, brings forth a sense of displacement and placelessness. The novels present and develop both authors’ spatial consciousness (that we call “ontological space”), which is not necessarily a container of three-dimensional objects, but instead, fictional emergent constructions. This thesis concludes that literature can become a meaningful space to cope with unbearable realities.

Do long-tailed macaques (Macaca fascicularis) know what others can and cannot hear?

Theory of mind has been defined as the ability to attribute mental sates such as perceptions, knowledge, and belief to others. Studies examining theory of mind in primates have been the center of intense controversy. Much of the research on this subject has focused on designing methodologies to test a primate’s ability to discern the perceptions of others. Namely, many studies have examined an individual’s knowledge of what others can and cannot see. However, other sensory modalities have not undergone as much extensive research. This study aimed to replicate the methodology of a previous experiment with the addition of two novel experimental conditions. Individual long-tailed macaques (Macaca fascicularis) were allowed to approach one of two identical, lidded, clear boxes which had jingle bells attached to them. One of the boxes had the metal bits removed from inside of the jingle bells attached to it, thus creating one “silent” box and leaving the remaining one “noisy”. The experimenter either looked directly at the subject, down at the ground between their knees, or in the novel conditions, turned their back to the subject, or wore a welder’s mask while facing the subject after demonstrating each box’s auditory properties. It was predicted that subjects would choose to approach the silent container in the latter three conditions. The results indicated that subjects selected boxes at random in all conditions. Additionally, in order to explore the possibility of perspective-taking representing a derived trait in the genus Macaca, a phylogeny of the genus was created and annotated to display the presence of perspective-taking as a phenotypic trait in extant species. Three likely evolutionary scenarios leading to the current distribution of perspective-taking are postulated and analyzed for parsimony through the number of assumed gains and losses. The most parsimonious tree suggests that perspective taking could be a conserved trait among the order, giving credence to the argument that some other variable was responsible the negative results in this experiment. It is suggested that the results of the present study represent an artifact of the social environment of the subject population. Moreover, arguments are made for the development of more naturalistic studies for examining mental state attribution in primates.

A state of war: Florida from 1939 to 1945

World War II profoundly impacted Florida. The military geography of the State is essential to an understanding the war. The geostrategic concerns of place and space determined that Florida would become a statewide military base. Florida's attributes of place such as climate and topography determined its use as a military academy hosting over two million soldiers, nearly 15 percent of the GI Army, the largest force the US ever raised. One-in-eight Floridians went into uniform. Equally, Florida's space on the planet made it central for both defensive and offensive strategies. The Second World War was a war of movement, and Florida was a major jump off point for US force projection world-wide, especially of air power. Florida's demography facilitated its use as a base camp for the assembly and engagement of this military power. In 1940, less than two percent of the US population lived in Florida, a quiet, barely populated backwater of the United States. But owing to its critical place and space, over the next few years it became a 65,000 square mile training ground, supply dump, and embarkation site vital to the US war effort. Because of its place astride some of the most important sea lanes in the Atlantic World, Florida was the scene of one of the few Western Hemisphere battles of the war. The militarization of Florida began long before Pearl Harbor. The pre-war buildup conformed to the US strategy of the war. The strategy of theUS was then (and remains today) one of forward defense: harden the frontier, then take the battle to the enemy, rather than fight them in North America. The policy of "Europe First," focused the main US war effort on the defeat of Hitler's Germany, evaluated to be the most dangerous enemy. In Florida were established the military forces requiring the longest time to develop, and most needed to defeat the Axis. Those were a naval aviation force for sea-borne hostilities, a heavy bombing force for reducing enemy industrial states, and an aerial logistics train for overseas supply of expeditionary campaigns. The unique Florida coastline made possible the seaborne invasion training demanded for US victory. The civilian population was employed assembling mass-produced first-generation container ships, while Floridahosted casualties, Prisoners-of-War, and transient personnel moving between the Atlantic and Pacific. By the end of hostilities and the lifting of Unlimited Emergency, officially on December 31, 1946, Floridahad become a transportation nexus. Florida accommodated a return of demobilized soldiers, a migration of displaced persons, and evolved into a modern veterans' colonia. It was instrumental in fashioning the modern US military, while remaining a center of the active National Defense establishment. Those are the themes of this work.

The Use of Thermal Capacity in Measuring the Effectiveness of Meals on Wheels Transport Containers

The Meals on Wheels (MOW) program is designed to help combat hunger in persons needing assistance. MOW has a duty not only to provide food but also to ensure that it reaches eligible clients safely. Given the population that MOW serves, transporting food safely takes on increased importance. This experiment focused on the major food safety issue of maintaining temperature integrity through the use of transport containers. For containers that did not contain electric heating elements, several factors influenced how fast the food temperature fell. Those factors included the U-value and size of the container as well as how many meals were in the container. As predicted, the smaller the U-value, the longer it took the temperature to fall. Larger containers did better at maintaining food temperatures, provided they were fully loaded. In general, fully loaded small and medium containers were better at maintaining food temperatures than larger containers loaded with the same number of meals.

Kinetic performance : a study in portable architecture

The purpose of this research was to explore a new way of experiencing a performance space using the portability and flexibility of a cargo container. Since the 17th century there has been a split between theater, as a written work, and architecture. Theater has lost its founding essence becoming more about the structure and less about the performance. Contemporary theater designs came through the development of street performances, which developed into theater types such as the Black Box and lately video and projection screening. With the exploration of kinetic uses in architecture and defragmentation of a cargo container there is a new step on the development of theater design. Using a cargo container gave me a familiar object with specific dimensions to start my exploration as well as the possibility of having the theater transported to many sites. The findings demonstrate that there are many unexplored possibilities to create a performance space outside the conventional theater that can promote new types of performances as well as the use of new technologies of video and projection.