Critical surface tension of acrylamide-grafted polypropylene copolymer by the contact angle method

The contact angles theta of polar liquids on PP-g-AM copolymer (AM content 0.19, 0.26, and 0.37 wt%) were measured. The critical surface tension gamma(c) of PP-g-AM films were evaluated by the Zisman plot (cos theta versus gamma(L)), the Young-Dupre-Good-Girifalco plot (1 + cos theta) versus 1/gamma(L)(0.5), and the log(1 + cos theta) versus log gamma(L) plot. The gamma(L) values estimated by the plot log(1 + cos theta) versus log gamma(L) were smaller than those obtained by the other plots.

Crystalline behavior and critical crystalline sequence length of propylene/alpha-olefin copolymer

The melting points(T-m), crystalline temperature(T-c) and crystallinity(chi(c)) of propylene/alpha-olefin (pentene-l, octene-1 and decene-1) copolymers have been investigated, The results show that the T-m, T-c and chi(c) of the copolymers are lower than those of propylene homopolymer, indicating that lower alpha-olefin incorporation in copolymer has strongly hampered the crystallization of propylene, From critical crystalline sequence length of several propylene/alpha-olefin copolymers, it can be seen that a long chain alpha-olefin has much stronger effect on crystallization of PP than a short alpha-olefin does.

DYNAMIC SCALING OF THE STRUCTURE-FUNCTION FOR SPINODAL DECOMPOSITION IN CRITICAL AND NONCRITICAL MIXTURES OF POLY(VINYL ACETATE) POLY(METHYL METHACRYLATE)

The dynamics of phase separation in a binary polymer blend of poly(vinyl acetate) with poly(methyl methacrylate) was investigated by using a time-resolved light-scattering technique. In the later stages of spinodal decomposition, a simple dynamic scaling law was found for the scattering function S(q, t)(S(q, t) approximately I(q, t)): S(q, t)q(m)-3 S approximately (q/q(m)). The scaling function determined experimentally was in good agreement with that predicted by Furukawa, S approximately (X) approximately X2/(3 + X8) for critical concentration, and approximately in agreement with that predicted by Furukawa, S approximately (X) approximately X2/(3 + X6) for non-critical mixtures. The light-scattering invariant shows that the later stages of the spinodal decomposition were undergoing domain ripening.

Three-stage transformation of chlorophyll transient fluorescence pattern under sustained dehydration and the discovery of critical water content in seaweeds

The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and investigated. The pulse amplified modulation (PAM) system was used to analyze the distinct fluorescence parameters during thallus dehydration. Results proved that the fluorescence kinetics of different seaweed all showed three patterns of transformation with sustained water loss. These were: 1) peak kinetic pattern (at the early stage of dehydration fluorescence enhanced and quenched subsequently, representing a normal physiological state). 2) plateau kinetic pattern (with sustained water loss fluorescence enhanced continuously but quenching became slower, finally reaching its maximum). 3) Platform kinetic pattern (fluorescence fell and the shape of kinetic curve was similar to plateau kinetic pattern). A critical water content (CWC) could be found and defined as the percentage of water content just prior to the fluorescence drop and to be a significant physiological index for evaluation of plant drought tolerance. Once thallus water content became lower than this value the normal peak pattern can not be recovered even through rehydration, indicating an irreversible damage to the thylakoid membrane. The CWC value corresponding to different marine species were varied and negatively correlated with their desiccation tolerance, for example. Laminaria japonica had the highest CWC value (around 90%) and the lowest dehydration tolerance of the three. In addition, a fluorescence "burst" was found only in red algae during rehydration. The different fluorescence parameters F-o, F-v and F-v, F-m were measured and compared during water loss. Both F-o and F-v increased in the first stage of dehydration but F-v/F-m. kept almost constant. So the immediate response of in vivo chlorophyll fluorescence to dehydration was an enhancement. Later with sustained dehydration F-o increased continuously while F-v decreased and tended to become smaller and smaller. The major changes in fluorescence (including fluorescence drop during dehydration and the burst during rehydration) were all attributed to the change in F-o instead of F-v This significance of F-o indicates that it is necessary to do more research on F-o as well as on its relationship with the state of thylakoid membrane.

Behavioral responses of tilapia (Oreochromis niloticus) to acute fluctuations in dissolved oxygen levels as monitored by computer vision

Behavioral and ventilatory parameters have the possibility of predicting the stress state of fish in vivo and in situ. This paper presents a new image-processing algorithm for quantifying the average swimming speed of a fish school in an aquarium. This method is based on the alteration in projected area caused by the movement of individual fish during frame sequences captured at given time intervals. The image enhancement method increases the contrast between fish and background, and is thus suitable for use in turbid aquaculture water. Behavioral parameters (swimming activity and distribution parameters) and changes in ventilation frequency (VF) of tilapia (Oreochromis niloticus) responded to acute fluctuations in dissolved oxygen (DO) which were monitored continuously in the course of normoxia, falling DO level, maintenance of hypoxia (three levels of 1.5, 0.8 and 0.3 mg l(-1)) and subsequent recovery to normoxia. These parameters responded sensitively to acute variations in DO level; they displayed significant changes (P < 0.05) during severe hypoxia (0.8 and 0.3 mg l(-1) level) compared with normoxic condition, but there was no significant difference under conditions of mild hypoxia (1.5 mg l(-1) level). There was no significant difference in VF between two levels of severe hypoxia 0.8 and 0.3 mg l(-1) level during the low DO condition. The activity and distribution parameters displayed distinguishable differences between the 0.8 and 0.3 mg l(-1) levels. The behavioral parameters are thus capable of distinguishing between different degrees of severe hypoxia, though there were relatively large fluctuations. (c) 2006 Elsevier B.V. All rights reserved.

Interannual fluctuations in floral longevity, pollinator visitation and pollination limitation of an alpine plant (Gentiana straminea Maxim., Gentianaceae) at two altitudes in the Qinghai-Tibetan Plateau

Prolonged floral longevity and bumblebees as dominate pollinators in alpine ecosystem have been suggested to overcome pollination limitation of alpine plants arising from the decrease of pollinator activity with increasing altitude. However, this conclusion has never been examined in the Qinghai-Tibetan Plateau (QTP), the highest and largest plateau in the world. In this study, we intended to test year-to-year correlations between floral longevity, visiting frequency and pollen limitation of this species between two populations (at 3200 m and 4000 m) of Gentiana straminea in this plateau. Pollinator exclusion elongated both male and female phases greatly at both sites, and durations of both male and female phases in natural condition varied greatly over three years. The visiting frequency of bumblebees varied greatly at the higher altitude, but seemed to be stable at the lower altitude. Seed production was pollination limited in both populations in most studied years. The floral durations, pollinator frequency and pollination limitation showed no significant and consistent variations with the increase of altitude. The previous hypothesis that the prolonged floral longevity of alpine plants can compensate for low levels of pollinator visitation therefore could not be confirmed, and our results further suggested that in the QTP platform, the altitude shows no consistent effect on the reproductive performance of this species, despite that the fluctuation of visit frequency intensified at the higher altitude.

压力和铁含量对铁方镁石(Mg1-xFex)O(x<=0.25)弹性常数影响的第一性原理研究

By first principle methods based on density functional theory (DFT),the equation of state(EOS) and elastic constants of both periclase and ferropericlase are calculated. The pressure and iron doping effects on the elastic constants of ferropericlase are investigated systematically. Firstly, we calculate the elastic constants of periclase and compare the obtained results with experimental data and other theoretical calculations, which shows a encouraging consistence and demonstrates the practicability of first-principle methods. Secondly, by adding iron into periclase crystal model, we build up ferropericlase with iron contents ranging from 0% to 25% mole percent. The corresponding elastic constants are calculated in a large pressure range(0~120GPa). Emphatically, the strong correlation of 3d electrons in transitional elements, such as iron, is difficult to treat in first-principle methods for a long time. The current solution is to make additional correction. During the initial stage of this study, the strong correlation of 3d electrons in iron is not considered, and we observed that addition of iron decreases the volume of ferropericlase, which is totally contradictory to the experimental data. By applying LDA+U approximation in order to solve the strongly correlated 3d electron of iron, we observed the expansion of volume by iron as expected. On the basis of the LDA+U approximation, the elastic constants of ferropericlase are calculated. After a detailed analysis of data obtained from theoretical calculations, we have reached the following conclusions:(1)pressure imposes positive effects on all elastic constants, and the degree of effects is C11>C12>C44. (2) Iron has no distinctive effects on C11 and C12, although some fluctuations are observed around 60GPa. However, iron has obvious softening effects on C44 The softening effects on C44 are intensified as pressure increases. Above the 100GPa, the effects increase greatly, even surpasses the pressure's positive effects in ferropericlase crystal models with iron mole percent of having 12.5%, 18.75% and 25% iron content. (3)As to the modulus deprived from elastic constants, iron has no effect on the adiabatic bulk module BS, only a little fluctuation around 60GPa. We find iron's softening effects on shear modulus G. (4)We find out that, compared with low iron content, elastic constants with iron content approaching 25mole% is consistently fluctuated，which may be caused by the limitations of the LDA+U approximation method itself. (5)We investigate the pressure and Fe doping effects on elastic anisotropy factor（A=(2C44+C12-C11)/C11） of ferropericlase and find out that iron contents will lower the critical isotropic pressure. At the same pressure, when the pressure is below the isotropic pressure, iron softens the anisotropy factor ; when pressure surpasses the isotropic pressure, iron increases the anisotropy factor.

Computational Vision: A Critical Review

We review the progress made in computational vision, as represented by Marr's approach, in the last fifteen years. First, we briefly outline computational theories developed for low, middle and high-level vision. We then discuss in more detail solutions proposed to three representative problems in vision, each dealing with a different level of visual processing. Finally, we discuss modifications to the currently established computational paradigm that appear to be dictated by the recent developments in vision.

Design thinking - a critical analysis.

The latest buzz phrase to enter the world of design research is “Design Thinking”. But is this anything new and does it really have any practical or theoretical relevance to the design world? Many sceptics believe the term has more to do with business strategy and little to do with the complex process of designing products, services and systems. Moreover, many view the term as misleading and a cheap attempt to piggyback the world of business management onto design. This paper seeks to ask is design thinking anything new? Several authors have explicitly or implicitly articulated the term “Design Thinking” before, such as Peter Rowe’s seminal book “Design Thinking” [1] first published in 1987 and Herbert Simon’s “The Sciences of the Artificial” [2] first published in 1969. In Tim Brown’s “Change by Design” [3], design thinking is thought of as a system of three overlapping spaces rather than a sequence of orderly steps namely inspiration – the problem or opportunity that motivates the search for solutions; ideation – the process of generating, developing and testing ideas; and implementation – the path that leads from the design studio, lab and factory to the market. This paper seeks to examine and critically analyse the tenets of this new design thinking manifesto set against three case studies of modern design practice. As such, the paper will compare design thinking theory with the reality of design in practice.

Development of process control methodology for tracking the quality and safety of pain, agitation and sedation management in critical care units

Objective: To develop sedation, pain, and agitation quality measures using process control methodology and evaluate their properties in clinical practice. Design: A Sedation Quality Assessment Tool was developed and validated to capture data for 12-hour periods of nursing care. Domains included pain/discomfort and sedation-agitation behaviors; sedative, analgesic, and neuromuscular blocking drug administration; ventilation status; and conditions potentially justifying deep sedation. Predefined sedation-related adverse events were recorded daily. Using an iterative process, algorithms were developed to describe the proportion of care periods with poor limb relaxation, poor ventilator synchronization, unnecessary deep sedation, agitation, and an overall optimum sedation metric. Proportion charts described processes over time (2 monthly intervals) for each ICU. The numbers of patients treated between sedation-related adverse events were described with G charts. Automated algorithms generated charts for 12 months of sequential data. Mean values for each process were calculated, and variation within and between ICUs explored qualitatively. Setting: Eight Scottish ICUs over a 12-month period. Patients: Mechanically ventilated patients. Interventions: None. Measurements and Main Results: The Sedation Quality Assessment Tool agitation-sedation domains correlated with the Richmond Sedation Agitation Scale score (Spearman [rho] = 0.75) and were reliable in clinician-clinician (weighted kappa; [kappa] = 0.66) and clinician-researcher ([kappa] = 0.82) comparisons. The limb movement domain had fair correlation with Behavioral Pain Scale ([rho] = 0.24) and was reliable in clinician-clinician ([kappa] = 0.58) and clinician-researcher ([kappa] = 0.45) comparisons. Ventilator synchronization correlated with Behavioral Pain Scale ([rho] = 0.54), and reliability in clinician-clinician ([kappa] = 0.29) and clinician-researcher ([kappa] = 0.42) comparisons was fair-moderate. Eight hundred twenty-five patients were enrolled (range, 59-235 across ICUs), providing 12,385 care periods for evaluation (range 655-3,481 across ICUs). The mean proportion of care periods with each quality metric varied between ICUs: excessive sedation 12-38%; agitation 4-17%; poor relaxation 13-21%; poor ventilator synchronization 8-17%; and overall optimum sedation 45-70%. Mean adverse event intervals ranged from 1.5 to 10.3 patients treated. The quality measures appeared relatively stable during the observation period. Conclusions: Process control methodology can be used to simultaneously monitor multiple aspects of pain-sedation-agitation management within ICUs. Variation within and between ICUs could be used as triggers to explore practice variation, improve quality, and monitor this over time

Understanding nurses’ decision-making when managing weaning from mechanical ventilation: a study of novice and experienced critical care nurses in Scotland and Greece.

Aim and objectives To examine how nurses collect and use cues from respiratory assessment to inform their decisions as they wean patients from ventilatory support. Background Prompt and accurate identification of the patient's ability to sustain reduction of ventilatory support has the potential to increase the likelihood of successful weaning. Nurses' information processing during the weaning from mechanical ventilation has not been well-described. Design A descriptive ethnographic study exploring critical care nurses' decision-making processes when weaning mechanically ventilated patients from ventilatory support in the real setting. Methods Novice and expert Scottish and Greek nurses from two tertiary intensive care units were observed in real practice of weaning mechanical ventilation and were invited to participate in reflective interviews near the end of their shift. Data were analysed thematically using concept maps based on information processing theory. Ethics approval and informed consent were obtained. Results Scottish and Greek critical care nurses acquired patient-centred objective physiological and subjective information from respiratory assessment and previous knowledge of the patient, which they clustered around seven concepts descriptive of the patient's ability to wean. Less experienced nurses required more encounters of cues to attain the concepts with certainty. Subjective criteria were intuitively derived from previous knowledge of patients' responses to changes of ventilatory support. All nurses used focusing decision-making strategies to select and group cues in order to categorise information with certainty and reduce the mental strain of the decision task. Conclusions Nurses used patient-centred information to make a judgment about the patients' ability to wean. Decision-making strategies that involve categorisation of patient-centred information can be taught in bespoke educational programmes for mechanical ventilation and weaning. Relevance to clinical practice Advanced clinical reasoning skills and accurate detection of cues in respiratory assessment by critical care nurses will ensure optimum patient management in weaning mechanical ventilation

Critical incident technique and explicitation interviewing in studies of information behavior

Urquhart, C., Light, A., Thomas, R., Barker, A., Yeoman, A., Cooper, J., Armstrong, C., Fenton, R., Lonsdale, R. & Spink, S. (2003). Critical incident technique and explicitation interviewing in studies of information behavior. Library and Information Science Research, 25(1), 63-88. Sponsorship: JISC (for JUSTEIS element)

The Lord of the Rings and ?Identification?: A Critical Encounter

Barker, M. (2005) 'The Lord of the Rings and 'identification': a critical encounter', European Journal of Communication, 20, 3, 353-378 Sponsorship: This research was made possible by a grant from the Economic and Social Research Council (ESRC Grant No. 000-22-0323)

Critical Security Studies and World Politics

Booth, Ken, Critical Security Studies and World Politics (Boulder, CO: Lynne Rienner Publishers, 2005), pp.ix+321 RAE2008