Short-term temporal changes of bare soil CO2 fluxes after tillage described by first-order decay models

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Soil CO2 emission of sugarcane fields as affected by topography

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desgaste corrosivo-cavitativo-erosivo de um aço-carbono em meio aquoso com frações de sal (NaCl), CO2 e particulados sólidos (SiO2)

A batch of eighty-four coupons of low carbon steel were investigated at laboratory conditions under a corrosive, cavitative-corrosive (CO2) and corrosive-erosive (SiO2 + CO2) in an aqueous salt solution and two levels of temperature. The following measurements were made on Vickers (HV0,05, HV0,10, HV0,20) Microhardness tests at three levels of subsurface layer. A turbulent flow collided on the cylindrical sample, with and without mechanical stirring and gas bubbling, with and without fluid contamination by solid particles of SiO2, at two temperatures. Surface Roughness and Waviness, under two conditions "as received, after machining" and "after worn out", as well as gravimetric and electrochemical parameter were measured on the two opposite generatrices of each cylindrical sample, on the flow upstream (0°) and downstream (180°) by Profilometry, Mass Variation and Linear Polarization Resistance (LPR). The results of the Microhardness and Surface Texture of all coupons were subjected to statistical comparison, using the software Statgraphics® Centurion XVI, 95% statistical certainty, and significant differences were observed in some arrays of measurements. The corrosive wear rate measured by LPR and mass variation shown to be sensitive to the presence of bubbles and hydrodynamic fluctuations inside the cell, considering the temperature and contamination of corrosive fluid by solid particles. The main results of visual inspection relative to some topologies of the surface damages involving different mechanisms that were seen to give explanation for some fluctuations in wear rates of the steel experimentally investigated

Avaliação da decomposição de plantas aquáticas no solo através da liberação de CO2

O objetivo deste trabalho foi avaliar a decomposição de três espécies de plantas aquáticas imersas, incorporadas ao solo, provenientes do controle mecânico, em reservatórios de usinas hidrelétricas. O estudo foi realizado em casa de vegetação, localizada no Núcleo de Pesquisas Avançadas em Matologia (NUPAM) da FCA/Unesp-Botucatu. A avaliação foi conduzida em vasos contendo 14 kg de solo, com três incorporações de 50 e 100 t MF de plantas ha-1, sob duas condições de solo: seco e úmido. Com a simulação de descarte da biomassa coletada e incorporada ao solo, pôde-se conhecer, através da liberação de CO2, a degradação de três espécies de macrófitas aquáticas submersas. Para quantificação do CO2 liberado, em cada vaso foi acondicionado um frasco com solução de NaOH, sendo, logo após, lacrados e incubados por 24 horas; em seguida, foram titulados com HCl. Para ajuste e interpolação dos dados, estes foram analisados seguindo modelo de Mitscherlich, com algumas modificações. As liberações acumuladas em solo úmido foram de 1.294 e 1.582 kg CO2 ha-1, sendo 6,2 e 5,6 vezes superiores ao ocorrido em solo seco, para 50 e 100 t MF ha-1, respectivamente, observando-se que cerca de 55% da liberação de CO2 ocorreu nos primeiros 30 dias. Pode-se concluir que o solo seco é a melhor condição para descarte e incorporação da biomassa, porém deverá existir um sistema de irrigação para que o processo de degradação da biomassa incorporada seja acelerado.

Extração do óleo essencial de Cymbopogom winterianus J. com CO2 pressurizado

The extraction with pressurized fluids has become an attractive process for the extraction of essential oils, mainly due the specific characteristics of the fluids near the critical region. This work presents results of the extraction process of the essential oil of Cymbopogon winterianus J. with CO2 under high pressures. The effect of the following variables was evaluated: solvent flow rate (from 0.37 to 1.5 g CO2/min), pressure (66.7 and 75 bar) and temperature (8, 10, 15, 20 and 25 ºC) on the extraction kinetics and the total yield of the process, as well as in the solubility and composition of the C. winterianus essential oil. The experimental apparatus consisted of an extractor of fixed bed and the dynamic method was adopted for the calculation of the oil solubility. Extractions were also accomplished by conventional techniques (steam and organic solvent extraction). The determination and identification of extract composition were done by gas chromatography coupled with a mass spectrometer (GC-MS). The extract composition varied in function of the studied operational conditions and also related to the used extraction method. The main components obtained in the CO2 extraction were elemol, geraniol, citronellol and citronellal. For the steam extraction were the citronellal, citronellol and geraniol and for the organic solvent extraction were the azulene and the hexadecane. The most yield values (2.76%) and oil solubility (2.49x10-2 g oil/ g CO2) were obtained through the CO2 extraction in the operational conditions of T = 10°C, P = 66.7 bar and solvent flow rate 0.85 g CO2/min

Liberação de CO2, biomassa microbiana e fósforo disponível em solo adicionado de matéria seca de poaia-branca

O presente experimento, inteiramente casualizado, foi desenvolvido em condições de laboratório no Departamento de Defesa Fitossanitária, FCA/UNESP - Botucatu, entre julho e setembro de 1992. Amostras de Areia Quartzosa equivalentes à 40 g de terra seca à 105 oC ± 2 com ou sem adição de 1,9 g de matéria seca de plantas de poaia-branca (Richardia brasiliensis), 0,19 g de nitrogênio (NH4)2SO4 e 0,88 g de apatita de Araxá, foram incubadas no escuro a 25 o C ± 2 , com umidade mantida a 60% da capacidade de retenção de água. Durante a incubação, determinou-se o CO2 liberado, utilizando-se o método de retenção em NAOH seguida de titulometria com HCl; a biomassa microbiana, método de fumigação-incubação; o pH e a quantidade de fósforo extraído por resina. A maior liberação de CO2 ocorreu durante os dez primeiros dias de incubação, com 77% do total de carbono liberado nos tratamentos com adição de poaia, e 37% nos tratamentos sem adição da mesma. A liberação de CO2 foi 57 vezes maior nos tratamentos com poaia em relação ao controle. A poaia também provocou aumentos na biomassa microbiana (média de 8 vezes a biomassa do tratamento controle), e a adição de nitrogênio e/ou fosfato de rocha junto à poaia antecipou os picos de formação de biomassa de 20 para 10 dias de incubação. Os níveis de fósforo disponível foram maiores no tratamento com adição de fosfato de rocha apenas. A poaia também alcalinizou o sistema, não permitindo desta forma, observar-se relação significativa entre pH e teor de fósforo disponível.

Avaliação da capacidade de adsorção do CO2 em zeólita 12X com gases sintéticos e originados da pirólise do lodo de esgoto

This work depicts a study of the adsorption of carbon dioxide on zeolite 13X. The activities were divided into four stages: study batch adsorption capacity of the adsorbent with synthetic CO2 (4%), fixed bed dynamic evaluation with the commercial mixture of gases (4% CO2, 1.11% CO, 1 2% H2, 0.233% CH4, 0.1% C3, 0.0233% C4 argon as inert closing balance), fixed bed dynamic modeling and evaluation of the breakthrough curve of CO2 originated from the pyrolysis of sewage sludge. The sewage sludge and the adsorbent were characterized by analysis TG / DTA, SEM, XRF and BET. Adsorption studies were carried out under the following operating conditions: temperature 40 °C (for the pyrolysis of the sludge T = 600 °C), pressures of 0.55 to 5.05 bar (batch process), flow rate of the gaseous mixture between 50 - 72 ml/min and the adsorbent masses of 10, 15 and 20 g (fixed bed process). The time for the adsorption batch was 7 h and on the fixed bed was around 180 min. The results of this study showed that in batch adsorption process step with zeolite 13X is efficient and the mass of adsorbed CO2 increases with the increases pressure, decreases with temperature increases and rises due the increase of activation temperature adsorbent. In the batch process were evaluated the breakthrough curves, which were compared with adsorption isotherms represented by the models of Langmuir, Freündlich and Toth. All models well adjusted to the experimental points, but the Langmuir model was chosen in view of its use in the dynamic model does not have implications for adsorption (indeterminacy and larger number of parameters such as occurred with others) in solving the equation. In the fixed bed dynamic study with the synthetic gas mixture, 20 g of mass adsorbent showed the maximum adsorption percentage 46.7% at 40 °C temperature and 50 mL/min of flow rate. The model was satisfactorily fitted to the three breakthrough curves and the parameters were: axial dispersion coefficient (0.0165 dm2/min), effective diffusivity inside the particle (dm2/min 0.0884) and external transfer coefficient mass (0.45 dm/min). The breakthrough curve for CO2 in the process of pyrolysis of the sludge showed a fast saturation with traces of aerosols presents in the gas phase into the fixed bed under the reaction process

A comparative solid state C-13 NMR and thermal study of CO2 capture by amidines PMDBD and DBN

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biomass consumption and CO2, CO and main hydrocarbon gas emissions in an Amazonian forest clearing fire

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biodiesel CO2 emissions: A comparison with the main fuels in the Brazilian market

The use of biodiesel is increasing as an attractive fuel due to the depleting fossil fuel resources and environmental degradation. This paper presents results of an investigation on the potentials of biodiesel as an alternative fuel and main substitute of diesel oil, comparing the CO2 emissions of the main fuels in the Brazilian market with those of biodiesel, in pure form or blended in different proportions with diesel oil (2%, 5%, and 20%, called B2, B5, and B20, respectively). The results of the study are shown in ton CO2 per m(3) and ton CO2 per year of fuel. The fuels were analyzed considering their chemical composition, stoichiometric combustion parameters and mean consumption for a single vehicle. The fuels studied were: gasoline, diesel oil, anhydrous ethyl alcohol (anhydrous ethanol), and biodiesel from used frying oil and from soybean oil. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. With data provided by the Brazilian Association of Automotive Vehicle Manufacturers (ANFAVEA) for the number of vehicles produced in Brazil, the emissions of CO2 for the national fleet in 2007 were obtained per type of fuel. With data provided by the Brazilian Department of Transit (DENATRAN) concerning the number of diesel vehicles in the last five years in Brazil, the total CO2 emissions and the percentage that they would decrease in the case of use of pure biodiesel, B100, or several mixtures, B2, B5 and B20, were calculated. Estimates of CO2 emissions for a future scenario considering the mixtures B5 and B20 are also included in this article. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

DCOOD optically pumped by a (CO2)-C-13 laser: new terahertz laser lines

In this work we report on new optically pumped THz laser lines from deuterated formic acid (DCOOD). An isotopic (CO2)-C-13 laser was used for the first time as a pump source for this molecule, and a Fabry-Perot cavity was used as a THz laser resonator. Optoacoustic absorption spectra were used as a guide to search for new THz laser lines. We could observe six new laser lines in the range from 303.8 mu m (0.987 THz) to 725.1 mu m (0.413 THz). The lines were characterized according to wavelength, relative polarization, relative intensity, and optimum working pressure. The transferred lamb-dip technique was used to measure the frequency absorption transition for both of these laser lines. Furthermore, we also present a catalogue of all THz laser lines generated from DCOOD.

Reforma a vapor catalítica do metano: Otimização da produção e seletividade em hidrogênio por absorção in situ do CO2 produzido

Topics of research related to energy and environment have significantly grown in recent years, with the need of its own energy as hydrogen. More particularly, numerous researches have been focused on hydrogen as energy vector. The main portion of hydrogen is presently obtained by reforming of methane or light hydrocarbons (steam, oxy, dry or auto reforming). During the methane steam reforming process the formation of CO2 undesirable (the main contributor to the greenhouse effect) is observed. Thus, an oxide material (sorbent) can be used to capture the CO2 generated during the process and simultaneously shifting the equilibrium of water gas shift towards thermodynamically more favorable production of pure hydrogen. The aim of this study is to develop a material with dual function (catalyst/sorbent) in the reaction of steam reforming of methane. CaO is well known as CO2 sorbent due to its high efficiency in reactions of carbonation and easy regeneration through calcination. However the kinetic of carbonation decreases quickly with time and carbonation/calcination cycles. A calcium aluminate (Ca12Al14O33) should be used to avoid sintering and increase the stability of CaO sorbents for several cycles. Nickel, the industrial catalyst choice for steam reforming has been added to the support from different manners. These bi-functional materials (sorbent/catalyst) in different molar ratios CaO.Ca12Al14O33 (48:52, 65:35, 75:25, 90:10) were prepared by different synthesis methodologies, among them, especially the method of microwave assisted self-combustion. Synthesis, structure and catalytic performances of Ni- CaO.Ca12Al14O33 synthesized by the novel method (microwave assisted selfcombustion) proposed in this work has not being reported yet in literature. The results indicate that CO2 capture time depends both on the CaO excess and on operating conditions (eg., temperature and H2O/CH4 ratio). To be efficient for CO2 sorption, temperature of steam reforming needs to be lower than 700 °C. An optimized percentage corresponding to 75% of CaO and a ratio H2O/CH4 = 1 provides the most promising results since a smaller amount of water avoids competition between water and CO2 to form carbonate and hydroxide. If this competition is most effective (H2O/CH4 = 3) and would have a smaller amount of CaO available for absorption possibly due to the formation of Ca(OH)2. Therefore, the capture time was higher (16h) for the ratio H2O/CH4 = 1 than H2O/CH4 = 3 (7h) using as catalyst one prepared by impregnating the support obtained by microwave assisted self-combustion. Therefore, it was demonstrated that, with these catalysts, the CO2 sorption on CaO modifies the balance of the water gas-shift reaction. Consequently, steam reforming of CH4 is optimized, producing pure H2, complete conversion of methane and negligible concentration of CO2 and CO during the time of capture even at low temperature (650 °C). This validates the concept of the sorption of CO2 together with methane steam reforming

Alterações do pH, da P O2 e da P CO2 arteriais e da concentração de lactato sangüíneo de cavalos da raça Árabe durante exercício em esteira de alta velocidade

Avaliaram-se as alterações do pH, da P O2 e da P CO2 do sangue arterial e da concentração de lactato sangüíneo de 11 cavalos adultos da raça Árabe, submetidos a exercício progressivo em esteira de alta velocidade. Antes do exercício, no intervalo dos 15 segundos finais de cada mudança de velocidade e aos 1, 3 e 5 minutos após o término do exercício foram coletadas amostras de sangue arterial e venoso para a mensuração dos gases sangüíneos e da concentração de lactato. O exercício resultou em diminuição do pH, da pressão parcial de O2 (P O2) e da pressão parcial de CO2 (P CO2). A concentração de lactato sangüíneo elevou-se exponencialmente a partir da velocidade de 8,0m/s até os momentos após término do exercício.

Crescimento e índices de troca gasosa em plantas de pepino irrigadas com água enriquecida com CO2

Avaliou-se o efeito do enriquecimento da água de irrigação com CO2 sobre índices fisiológicos de desenvolvimento e troca gasosa de folhas de plantas de pepino do tipo japonês, cultivados em ambiente protegido. Os experimentos realizados em duas épocas do ano foram instalados em delineamento experimental de blocos ao acaso com 4 tratamentos e 5 repetições. Os tratamentos foram constituídos pelos híbridos Hokuho e Tsuyataro, irrigados com água comum ou enriquecida com CO2, em uma concentração de 1 no primeiro e 0,25 no segundo experimento. A produção de massa de material seco e área foliar adotaram tendência exponencial, não sendo possível observar o início da diminuição da taxa de produção de massa do material seco aos 63 dias após transplante (DAT). A taxa de crescimento da comunidade e taxa de crescimento relativa do híbrido Hokuho irrigado com água comum foi diferente do irrigado com água enriquecida com CO2, no entanto, no híbrido Tsuyataro foram semelhantes. A taxa de assimilação líquida atingiu a máxima pendente na fase de crescimento vegetativo e floração, e foi reduzida drasticamente após os 20 DAT no híbrido Hokuho, e após os 35 DAT no híbrido Tsuyataro. A razão de área foliar diminuiu ligeiramente nos dois híbridos com o desenvolvimento do cultivo. No início observaram-se diferenças entre irrigação com água comum e enriquecida com CO2, porém após 20 DAT não se apreciaram mais diferenças. Quanto a troca gasosa, a taxa assimilatória líquida de CO2 e de transpiração, conductância estomática e eficiência no uso da água foram semelhantes entre plantas irrigadas com água comum e enriquecida com CO2 durante o primeiro semestre. Já no segundo semestre, maiores valores foram registrados pelas plantas irrigadas com água enriquecida.